Digital Equipment DECstation 5000 Upgrade Instructions
DECstation 5000
Model 1xx to DEC
3000 Model 300 AXP
Upgrade Instructions
MLO-010693
Part Number: EK–DS513–UP. A01
Options You Can Upgrade
Can Cannot
Upgrade Upgrade
Drives: RZ23L, RZ24L RZ57
RZ24, RZ25 RX23
RZ26 RX33
RZ55 (e) TK50Z
RZ56 (e) RRD40
RZ58 (e) RW100
RRD42 (t)
TLZ04 (e)
TLZ06 (t)
TKZ081(e)
TKZ091(e)
TSZ071(e)
TZK101(e)
TZ30 (e)
Expansion
Boxes: PMTcE**
SZ03
SZ12
SZ16
Input
Devices: VSXXX-AA/AB LK501
VSXXX-GA/GB VSXXX-BB
VSXXX-FA/JA
VSXXX-XX
VSX10-AA/A3*
VSX20-AA/A3*
VSX30-AA/A3*
(e) Supported in external device only.
(t) Supported in external device including tabletop.
1
Support planned.
*DEC Open3D required for software support.
**Minimum revision of host module must be D03.
Options You Can Upgrade
Can Cannot
Upgrade Upgrade
Graphics
Modules: PMAGB-BA/BB PMAG-AA/AB
PMAGB-BC/BD PMAG-DA/DB
PMAGB-JA/JB AV10U-AA/DA
PMAG-GB/HA PMAG-EA/EB
PMAGB-BE/BF PMAG-FA/FB
PMAGB-DA/DB* PMAGB-ED/EC
PMAGB-EA/EB* PMAGB-DC/DD
PMAGB-FA/FB2PMAG-CA/CB
PMAG-JA/JB
PMAG-BA/BB
Memory: None
Monitors: VR319-Dx VR262-Ax
VR320-Dx VR290-Dx
VRC16-Cx/Hx VR297-Dx
VRM17-Ax/Hx VR299-Dx
VRT16-Hx VRT19-Dx
VRT19-Hx VR319-Cx
VR320-Cx
VRT16-Dx
VRT13
TURBOchannel
Devices: DEFZA-AA
PMAD-AA/AB DSYT1-AB
1
DEFZA-CA
PMAZ-AA/AB
*DEC Open3D required for software support.
1
Support planned.
2
DEC Open3D and PMTcE required for support.
x=variable model number
Check the Components Shipped
Your shipment should contain the following
two kits:
System Kit:
Mouse
with Mousepad
System Unit
Universal
Strain Relief
Strap
Keyboard
SCSI
Terminator
Documentation
Antistatic
Wrist Strap
10BASE-T Loopback
Connector
Modem Loopback
Connector
Network
Cable
Accessory Kit:
Mounting
Brackets (2)
Return
Address
Label
Monitor
Video Cable
Keyboard/Mouse
Extension Cable
Monitor
Power Cord
System Power
Cord
Screwdriver
External
SCSI Cable
Upgrade
Card
Screws (8)
xxxxxxx
xxxxxxxxxxx
xxx
MLO-010839
Record Your System SCSI IDs
If your DEC 3000 system has a factoryinstalled drive, you may need to change the
SCSI ID setting on the drive you upgrade.
To display the SCSI ID settings of the drives
in your DECstation system:
1. Enter the following command to shut
down the software and put the system in
console mode:
2. Enter the cnfg 3 command at the
console prompt (>>). A screen similar to
the following displays:
>>cnfg 3
3: KN02 DEC Vn.n TCF0 (8 MB)
(enet: 08-00-2b-30-14-df)
(SCSI = 7)
--------------------------------------------- DEV PID VID REV SCSI ID
==============================================
rz2 RZ24 (C) DEC DEC 0700 DIR
rz5 RRD42 (C) DEC DEC 0700 CD-ROM
.
.
shutdown -h now
This example display shows an RZ24 drive
set to SCSI ID 2 and an RRD42 drive set to
SCSI ID 5.
Write down your system drive names and
SCSI ID settings here:
Loading...