DIGITALas D-FORCE1400VA, D-FORCE600VA User Manual
Sliding Gate Operator
User's Manual
D-FORCE1400VA
D-FORCE1400VA SLIDING GATE OPERATOR
1. Products introduction
Please read the instructions carefully before proceeding.
MCU is supplied to control the gate operator.
Keypad / single button interface.
Have Infrared safety sensor interface.
Soft start and soft stop function and the soft stop width are adjustable.
Working time is adjustable.
Motor output torque is adjustable.
User can select Auto-close function.
Manual key release designed for emergency purposes.
2. Important safety information
Carefully read and follow all safety precautions and warning before
attempting to install and use this automatic gate operator.
The gate operator should be installed by a qualified technician;
otherwise, serious personal injury or property damage may occur.
When opening or closing the gate, do not attempt to walk or drive
through the gate.
If enable the auto-close function, must use the infrared sensor.
Children should not be allowed to play near or operate automatic
gates.
The automatic gate operator must be grounded.
Install the gate operator on the inside of the property; DO NOT install
it on the outside of the property where the public has access to it.
Be careful when in close proximity to moving parts where hands or
fingers could be pinched.
Do not allow control devices to be placed so that a person can access
them by reaching through the gate.
In the event of power failure, an emergency release key allows you to
2
D-FORCE1400VA SLIDING GATE OPERATOR
operate the gate manually.
The operator should be switched off before repairing it or opening its
cover.
Please erase and reprogram the transmitter code after installing the
operator.
Make sure the Power supply (AC220V or AC110V) of the gate operator is
suitable for the power supply in your area.
3. Main technical parameters
Type D-FORCE1400VA D-FORCE1400VAU
Power supply 220V, 50Hz 110V, 60Hz
Motor speed 52rpm 62rpm
Rated output power of motor 500W
Remote control operating distance 30m (Frequency:433.92mHz)
Remote control mode Single button
Output shaft height 58.5mm
Max. gate weight 1400Kg
Output torque 32N·m
Noise ≤60dB
Duty cycle S2, 15 minutes
extra remote control 20
Environmental temperature -20°C~+50°C
Gate Move speed 12m/min 14m/min
3
D-FORCE1400VA SLIDING GATE OPERATOR
4. Mechanical Installation
The D-FORCE1400VA will handle gate weighting up to 800kg/1400 kg
and up to 14m/20m if the proper installation procedures have been
followed.
The D-FORCE1400VA gate operator operates by forcing a drive rack by a
drive gear. The entire configuration is shown in the diagram below. The
gate operator must be installed on the inside of the gate.
Wall
Switch
Gate operator
Input power
Rack
Sliding gate
Fig.1
Gate preparation
Be sure the gate is properly installed and slides smoothly before installing
the D-FORCE1400VA sliding gate operator. The gate must be plumb, level,
and move freely.
Conduit
In order to protect the cable, use PVC conduit for low voltage power cable
and control wires. Conduit must be preset into the concrete when it is
poured. Wires within the conduit shall be located or protected so that no
4
D-FORCE1400VA SLIDING GATE OPERATOR
damage can result from contact with any rough or sharp part.
Concrete p ad
The base unit of the gate operator requires a concrete pad in order to
maintain proper stability. The concrete pad should be approximately
450mm x 300mm x 200mm deep in order to providing for adequate weight
and structure to insure proper stable installation.
Anchors (see Fig.2)
You can use anchor bolts, anchors, washers and nuts. These anchors must
be set into the concrete when it is poured or you can use wedge anchors to
fasten the operator.
Gate operator
Gear
Groundsill
Input power
Plain washer
Nut
Spring washer
Nut
Fig.2
Ope rator b ase (see Fig.3)
After the concrete has hardened, mount the gate operator base to the
concrete pad. Verify that the base is properly leveled.
Using bolts and washers mount the gate operator to the base and insert the
cover. Check the operator and make sure it is lined up with the gate.
5
D-FORCE1400VA SLIDING GATE OPERATOR
230
114
Fig.3
Installation of Rack
Fix the three nuts (in the same package with rack) on the rack element.
Lay the first piece of rack on the gear and weld the first nut on the
gate.
Move the gate manually, checking if the rack is resting on the gear,
and weld the second and third nut.
Bring another rack element near to the previous one. Move the gate
manually and weld the three nuts as the first rack, thus proceeding
until the gate is fully covered.
When the rack has been installed, to ensure it meshes correctly with
the gear.
The space between rack and gear is about 0.5mm.
6
D-FORCE1400VA SLIDING GATE OPERATOR
Fig.4
5. Adjustment
Spring limit switch
To ensure safety, it is recommended to install limit switches at both
ends of the gate to prevent the gate from sliding out of the rails. The
rails must be installed horizontally.
Install the limit block as shown in Fig.5 and Fig.6. The spring limit
switch and blocks are used to control the position of the gate.
Release the gear with the key and push the sliding gate manually to
pre-determine the position, fix the block to the rack and lock the gear
by push up the release bar. Moving the gate electrically, adjust the
block to the proper position until the position of the opening and
closing meet the requirement.
7
Loading...