Digisol DG-WM6305SIE2 User Manual

1

DG-WM6305SIE2

User Manual

2018-03-13

As our products undergo continuous development the specifications are subject to change without prior notice.

V1.0

DG-WM6305SIE2 User Manual

2

COPYRIGHT

Copyright 2017 by Digisol Systems Ltd. All rights reserved.

Company has an ongoing policy of upgrading its products and it may be possible
that information in this document is not up-to-date.

Please check with your local distributors for latest information. No part of this
document can be copied or reproduced in any form without written consent from
the company.

TRADEMARK

DIGISOLTMis a trademark of Digisol Systems Ltd. All other trademarks are the
property of the respective manufacturers.

DG-WM6305SIE2 User Manual

3

1. Hardware and Operation mode Instruction

………………………………………

.4

2. Connect Wireless AP Router with PC………………………………………………8

3. Login………………………………………………………………………………..9

4. WEB GUI Interface Setting………………………………………………………..11

5. Share Internet and obtain IP address automatically

……………………………

..30

INDEX

1.1. LED Indicator………………………………………………………………...4

1.2. AP Router Interface…………………………………………………………4

1.3. Power Supply………………………………………………………………..5

1.3.1. PoE Adapter Power Supply…………………………………………..5

1.3.2. PoE Switch Power Supply…………………………………………….5

1.4. AP Router Installation……………………………………………………….7

4.1. Status

4.2. Wizard Configuration

4.3. Advanced Setting…………………………………………………………..22

Troubleshooting……………………………………………………………………...31

………………………………………………………………………

………………………………………………………

4.2.1. Gateway Mode

4.2.2. WiFi Repeater Mode

4.2.3. Wisp Operation Mode

4.2.4. AP Operation Mode………………………………………………...21

4.3.1. Device Status……………………………………………………….22

4.3.2. Wireless Setting…………………………………………………….23

4.3.3. Virtual AP……………………………………………………………25

4.3.4. Access Control………………………………………………………26

4.3.5. Advanced Settings…………………………………………………..27

4.3.6. Network Setting

4.3.7. Management

……………………………………………………

………………………………………………

………………………………………………

……………………………………………………

………………………………………………………

.11

14

...14

..16

19

.27

..28

DG-WM6305SIE2 User Manual

4

DC 12V Power Adapter

 Patch Cord

Mounting Screws

RST

Reset Button, it make AP Router revert to de fau l t settings after pressing it

WAN

WAN Port, connect with ADSL modem or Internet mainly. It will b e LAN port
under Wirel ess AP Router and WiFi Repeater operation mode

LED

LED Indicator for WAN port and LAN port

DC

DC power connector

1. Hardware and Operation mode Instruction

Package Contents

Before using this access point, please check if there is anything missing in the
package, and contact your dealer of purchase to claim for missing items:



DG-WM6305SIE2 Ceiling Mount AP Router



 User Manual CD


1.1. LED Indicator

Green:- Power Indicator
Blue:- WiFi Indicator

1.2. AP Router Interface

for 15 seconds.

LAN LAN Port to end user s

DG-WM6305SIE2 User Manual

5

1.3. Power Supply:

1.3.1. PoE Adapter Power Supp ly:

The connection diagram showed as P1, internet cable connect to PoE adapter’s LAN
Port, Ceiling AP Router’s WAN port connect to PoE adapter’s PoE Por t, then PC will
access into ceiling AP t hrough cable or wireless. The wireless AP Router support 48V
IEEE 802 .3af standard PoE, the PoE adapter should be 48V PoE standard.

D

P1

1.3.2. PoE Switch Power Sup ply:

The connection diagram showed as P2, Internet cable from PoE Switch t o Ceiling AP’s
W

AN Port, then PC access into ceiling AP wired/wireless.If the PD wireless AP

support 48V IEEE 802.3af standard PoE, then the PoE switch should comply with

802.3af 48V PoE standard.

D

P2

Operation Mode:

There are three operation mode on this wireless AP:

6

P3

DG-WM6305SIE2 User Manual

D

D

D

P4

P5

D

D

DG-WM6305SIE2 User Manual

7

1.4. AP Router Installation:

The Ceiling Wireless AP Router, will be installed under ceiling based on following
steps:

P6

DG-WM6305SIE2 User Manual

8

2. Connect Wireless AP Router with PC

Connect the PC with wireless AP by Wireless SSID and LAN cable:
The diagram of wireless connection showed as follow:
Pls note: the default SSID is DG-WM6305SIE2-2.4G/5.8G, SSID’s are open with no
password.

P7: Connecting the PC to the AP with wireless

P8: Connecting the PC to the AP with wired LAN

DG-WM6305SIE2 User Manual

9

3. Login

1. Connect the Ceiling AP Router with computer by wired or wireless

2. The default IP address of this wireless AP Router is 192.168.1.200. Configure the

PC’s local connection. IP address as 192.168.1.X (X is number from 2 to 254), subnet
mask is 255.255.255.0.

P9

P10

10

3. Input 192.168.1.200 into browser, login page will appear, the default login

password: admin.

4. After login the following page appear which shows Device Status. This page will

DG-WM6305SIE2 User Manual

P11: Login Page

show the device default operation mode, Channel, Connection status, CPU usage,
Wireless settings, LAN Setting, Wireless AP’s Location, Hardware/Firmware version.

P12: Device Status

11

4. WEB GUI interface Setting

4.1. Status

After login, the Device Status and home page will be showed

DG-WM6305SIE2 User Manual

P13: Device Status

This page, show the device default operation mode, channel, end user QTY,
connection status, CPU usage status, Wireless, LAN and AP location info.

In this ceiling wireless AP, the default operation mode is AP mode.
Then in 2.4G Wireless Setting, GUI configuration page shown as below:
User can configure the SSID, Password, Band width, Channel then Apply to finish.

12

P14: 2.4G Wireless Setting

DG-WM6305SIE2 User Manual

Then in 5G Wireless Setting, GUI configuration page shown as below:
User can configure the SSID, Password, Band width, Channel then Apply to finish.

P15: 5G Wireless Setting

DG-WM6305SIE2 User Manual

13

As shown below user can set LAN Setting to configure the DHCP or Static IP address.

P16: LAN Setting

AP location setting: can mark where the AP set up, and AP name.

P17: AP Location Setting

DG-WM6305SIE2 User Manual

14

4.2. Wizard Configuration

Wizard: It instruct users to configure wireless AP Router’s operation mode based on
needs, there are four operation mode including Gateway, Repeater, WISP, Wireless
AP. Please confirm the operation mode first before starting the configuration.

Clicking Wizard in Status page will pop up following page to configure the operation
mode and there are explanation for each operation mode for better application.

P18: Wizard Configuration

4.2.1 Gateway Mode

Before Clicking the Gateway mode, confirm your internet will be Static IP, PPPoE, or
DHCP. Then clicking on the Gateway mode will pop up the below image. Please
choose the right WAN setting mode, then click next to continue. Then configure the
wireless parameters and click next.

P19: WAN Setting in Gateway Mode

DG-WM6305SIE2 User Manual

15

P20: Wireless Setting in Gateway Mode

Please note: to make the device work in some clear channel, user can click wireless
analyzer at first. Check Less AP in the channel, and then select your channel
accordingly, then Wireless performance will be more stable. Picture shown as below:

P21: 2.4G Wireless Analyzer

Clicking next will complete the Gateway mode setting and show following picture:

Please Note: The equipment will restart automatically for the changes to take effect.

DG-WM6305SIE2 User Manual

16

P22: Settings Complete in Gateway Mode

When return to Status page, will show Wireless router’s SSID, Internet connection,
LAN connection status shown as below.

P23: Status in Gateway Mode

4.2.2. WiFi Repeater mode

1. Login the Web management page, click “Wizard” then “WiFi Repeater”

2. Scan AP and select the AP’s SSID want to bridge then input the AP’s key, click next
to complete.

DG-WM6305SIE2 User Manual

17

P24: Repeater Mode

Click next to configure the Wireless Setting as follows, then click next to finish.

P25: Wireless Setting in Repeater Mode

Click Return button, will back to Status, show Repeater mode data, will show fail or
success, and user can configure this data in this page if required.

Please Note: The equipment will restart automatically for the changes to take effect.

18

P26: Status in Repeater Mode

DG-WM6305SIE2 User Manual

In wifi repeater operation mode, the default is SSID disable. If you want to enable
SSID, then click Wireless Setting.
Pls note, when click wireless relay setting, following page will pop up, you can make
changes from here easily.

P27: Wireless Relay Settings

DG-WM6305SIE2 User Manual

19

4.2.3. WISP Operation mode

Click WISP operation mode in Wizard, then will pop up the configure page, please set
the WISP operation mode based on the steps shown in picture:

P28: WISP Mode

Select the appropriate wireless AP and configure the correct WAN setting in WISP
operation mode, then next to complete.

Please Note: The equipment will restart automatically for the changes to take effect.

P29: WAN Setting in WISP Mode

20

Configure the Wireless Data as shown below

P30: Wireless Setting in WISP Mode

DG-WM6305SIE2 User Manual

Then complete and back to status, will show the connection fail or success, then can
configure the data based on request:

P31: Status in WISP Mode

DG-WM6305SIE2 User Manual

21

4.2.4. AP Operation mode

Set the wireless data, AP Location info as required, then click next to continue and
enter into LAN setting.
After LAN setting, complete the AP mode configuration and back to Status:

P32: Wireless Setting in AP Mode

P33: LAN Setting in AP Mode

Please Note: The equipment will restart automatically for the changes to take effect.

22

P34: Status in AP Mode

DG-WM6305SIE2 User Manual

4.3. Advanced Setting

In advanced setting you can get wireless AP Router’s device status, Wireless setting,
Network setting and AP management configuration. Let’s click Advanced Setting in
status page, will show Return home, Setup Wizard which we showed before.
Let’s see more in Device Status, Wireless, Network and Management in following
pages:

4.3.1. Device Status

To show the device status, Wireless Status and LAN status.
In status, mainly to check the AP Router’s firmware version, hardware version,
uptime info.

P35: Device Status

Wireless status show wireless AP’s SSID, MAC address for WiFi, Channel, Encryption,
Client List info.

23

P36: 2.4G Wireless Status

DG-WM6305SIE2 User Manual

P37: 5G Wireless Status

In LAN Status, we can check device IP address, Subnet Mask, LAN MAC address and
other info showed in following picture.

P38: LAN Status

4.3.2. Wireless Setting

Wireless setting, mainly to configure the wireless SSID, password, encryption,
channel, Multi SSID, tag VLAN & RF power adjust from Basic Setting, Virtual AP,
Access control and Advanced Setting:

DG-WM6305SIE2 User Manual

24

2.4G Wireless Setting: In this part, will show the 2.4G Basic Setting, Virtual AP,
Access control and Advanced Setting:

P39: Basic Settings in 2.4G Wireless Setting

5G Wireless Setting: In this part, will show the 5G Basic Setting, Virtual AP, Access
control and Advanced Setting:

P40: Basic Settings in 5G Wireless Setting

Wireless Status: On mean SSID on, Off mean SSID off.

2.4G Wireless Analyzer: Mainly to analyze the AP’s signal strength and channel, to

make user more easy to choose the channel with less wireless AP and to avoid the
Wireless Interference.

25

P41: 2.4G Wireless Analyzer

DG-WM6305SIE2 User Manual

4.3.3. Virtual AP

There are 3 virtual AP in 2.4G and in 5G wireless, for use of multi SSID, then users
can configure it as shown in following picture.

P42: 2.4G Virtual AP

26

4.3.4. Access Control

DG-WM6305SIE2 User Manual

P43: 5G Virtual AP

Allow or deny the users access into this device based on MAC address.

P44: 2.4G Access Control Settings

P45: 5G Access Control Settings

DG-WM6305SIE2 User Manual

27

4.3.5. Advanced Settings

This page, will show the regional info, mode, RF Power, Max user access,etc.

P46: 2.4G Advanced Wireless Settings

P47: 5G Advanced Wireless Settings

4.3.6. Network Setting

In network, you can configure LAN setting and tag VLAN as follow:
In LAN Settings, mainly including Static IP and DHCP.

DG-WM6305SIE2 User Manual

28

P48: LAN Settings

In VLAN part, you need an VLAN switch and make sure the multi SSID is enable, then
input the VLAN ID to different SSID.

P49: Tag VLAN Setting

4.3.7. Management

It show’s the System time, Logs, Upgrade firmware, System, User info.

System Time:- Can confgure the device timing

P50: System Time

DG-WM6305SIE2 User Manual

29

Upgrade Fimrware:- Browse the fimrware file and click on upgrade. Wait till the
upgrade is successfull. The device will reboot automatically and successfull firmware
upgrade.

P51: Firmware Upgrade

System:- You can save the config or restore the previously saved config or reset the
device to its default config.

P52: System Settings

DG-WM6305SIE2 User Manual

30

5. Share Internet and Obtain IP address

automatically

Set computer’s TPC/IP as Obtain an IP address automatically, Obtain DNS server
address automatically as following picture showed.
The computer will obtain the IP address from router or base station to get Internet.

P53

DG-WM6305SIE2 User Manual

31

Failure phenomenon

Solution

SYS Indicator off

Pls make sure the PoE module connection is right. POE Port
connect with AP, LAN port connect with computer

Can’t land to Wireless AP
through Web page

Pls check the IP address of computer and Wireless AP to see
whether they are in same networking segment, The method
is click “start”-“Run” input“cmd”，ping 192.168.1.200 to test
the Wireless AP connectivity.
Reset Wireless AP and load it again;
Pls make sure the IP address 192.168.1.200 is not occupied
by other device in Wireless AP’s networking;
Check computer and cable problem, recommend to use
10/100M UTP unshielded cable;
Clean up Arp binding from “Start”-“Run” input“cmd” arp –d
Clean the IE Brower’s temporary files and Cache file。

Wireless AP can’t connect
with AP（the status display
unconnected）

Try to scan the avaliable wireless networking again；
Make sure the Wireless AP’s wireless standard is correct；
(2.4Ghz signal should connect 2.4Ghz, 5.8Ghz signal should
connect 5.8Ghz signal).
The Security and passwords are matched between Wireless
AP Router and AP；
The signal strength of AP is too weak to connect, should be
more than -75dBm；

Can’t scan the wireless AP

Scan it several times more；
If using 5Ghz to scan, please make sure there are 5G
signal existed.
Reset the device, scan it again after device restarts；；

The connection of Wireless
AP and AP is success, but
the computer can’t share
internet

Pls Check the computer’s IP address and DNS setting. If it is
dynamic, set the network card as automatically obtain. If it is
static IP, pls contact with ISP for correct IP address and DNS
address.

Troubleshooting

The Failure phenomenon and solution.

If the problems are not listed, please contact the local service or call the Toll Free
service. We are willing to offer the service.

DG-WM6305SIE2 User Manual

32

How to Reset Wireless AP
Router

Press the “Reset” button more than 15 seconds after
power on. The device will restore factory default after it
restarts.

This product comes with three Years warranty. For further details about warranty

policy and product registration, please visit support section of www.digisol.com

DG-WM6305SIE2 User Manual

33