How it Works
DIGISOL
Loading...
DG-BG4300N
User Manual
103 pgs3.66 Mb0

DIGISOL DG-BG4300N User Manual

DG-BG4300N
300Mbps Wireless ADSL2/2+
Broadband Router
User Manual
V1.0
As our product undergoes continuous development the specifications are subject to change without prior notice
DG-BG4300N User Manual
COPYRIGHT
Copyright © 2011 by this company. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of this company
This company makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranties, merchantability or fitness for any particular purpose. Any software described in this manual is sold or licensed "as is". Should the programs prove defective following their purchase, the buyer (and not this company, its distributor, or its dealer) assumes the entire cost of all necessary servicing, repair, and any incidental or consequential damages resulting from any defect in the software. Further, this company reserves the right to revise this publication and to make changes from time to time in the contents thereof without obligation to notify any person of such revision or changes.
Trademarks:
DIGISOL™ is a trademark of Smartlink Network Systems Ltd. All other trademarks are the
property of the respective manufacturers.
DG-BG4300N User Manual
INDEX
1. Product Information ......................................................................................................... 6
1.1 Introduction and Safety Information .................................................................................. 6
1.2 Other features of the router .............................................................................................. 6
1.3 Safety Information ......................................................................................................... 7
1.4 System Requirements ..................................................................................................... 8
1.5 Package Contents ........................................................................................................... 8
1.6 Get Familiar with your new ADSL2+ Wireless broadband router ............................................ 9
2. System and Network Setup ............................................................................................. 11
2.1 Hardware Installation ................................................................................................... 11
3. Software Installation ....................................................................................................... 13
4. Web Browser Configuration ............................................................................................. 22
5. Setup ............................................................................................................................ 27
5.1 WAN Configuration .................................................................................................... 27
5.1.1 ATM Settings ...................................................................................................... 29
5.1.2 ADSL Settings ..................................................................................................... 30
5.2 LAN Configuration ..................................................................................................... 32
5.2.1 LAN Interface Setup ............................................................................................ 32
5.2.2 DHCP Mode ........................................................................................................ 33
5.2.2.1 DHCP Server Configuration ........................................................................... 33
5.2.2.2 DHCP Relay Configuration ............................................................................ 34
5.2.3 DHCP Static Configuration ................................................................................... 35
5.2.4 LAN IPV6 Configuration ....................................................................................... 36
5.3 Wireless Configuration ............................................................................................... 40
5.3.1 Basic Setting ....................................................................................................... 40
5.3.2 Wireless Security Setup ....................................................................................... 41
5.3.3 Wireless Multiple BSSID Setup ............................................................................. 43
5.3.4 Wireless Access Control ....................................................................................... 44
5.3.5 Wireless Advanced Settings ................................................................................. 45
5.3.6 WPS ( Wi-Fi Pprotected Setup) ............................................................................ 48
6. Advanced Setup ............................................................................................................. 50
6.1 Route Setup .............................................................................................................. 51
6.1.1 Static Route Setup .............................................................................................. 51
6.1.2 IPv6 Routing Configuration .................................................................................. 52
6.1.3 RIP Configuration ............................................................................................... 53
6.2 NAT Configuration ..................................................................................................... 54
6.2.1 DMZ Setup ......................................................................................................... 54
6.2.2 Virtual Server ...................................................................................................... 55
6.2.3 NAT Forwarding Setup ......................................................................................... 58
6.2.4 NAT ALG and Pass-Through ................................................................................. 59
6.2.5 NAT EXCLUDE IP Setup ....................................................................................... 60
6.2.6 NAT Port Trigger ................................................................................................. 60
6.2.7 FTP ALG Configuration ........................................................................................ 61
6.2.8 NAT IP MAPPING ................................................................................................ 62
DG-BG4300N User Manual
6.3 QoS .......................................................................................................................... 63
6.3.1 IP QoS ............................................................................................................... 63
6.4 CWMP Setup ............................................................................................................. 65
6.4.1 TR-069 Configuration .......................................................................................... 65
6.5 Port Mapping Setup ................................................................................................... 67
6.5.1 Port Mapping Configuration ................................................................................. 68
6.6 Others ...................................................................................................................... 69
6.6.1 Bridge Setting ..................................................................................................... 69
6.6.2 Client Limit Configuration .................................................................................... 70
6.6.3 Tunnel Configuration ........................................................................................... 71
6.6.4 Other Advanced Configuration ............................................................................. 72
7. Service Setup ................................................................................................................ 73
7.1 IGMP Configuration ................................................................................................... 73
7.1.1 IGMP Proxy Configuration .................................................................................... 74
7.1.2 MLD Configuration .............................................................................................. 75
7.2 UPnP Setup ............................................................................................................... 77
7.2.1 UPnP Configuration ............................................................................................. 77
7.3 SNMP Setup .............................................................................................................. 78
7.3.1 SNMP Protocol Configuration ............................................................................... 78
7.4 DNS Setup ................................................................................................................ 79
7.4.1 DNS Configuration ............................................................................................... 79
7.4.2 IPv6 DNS ............................................................................................................ 80
7.5 Dynamic DNS ............................................................................................................ 81
7.5.1 Dynamic DNS ( DDNS) Configuration .................................................................... 81
8. Firewall Setup ................................................................................................................ 83
8.1 MAC Filtering ............................................................................................................ 83
8.2 IP/Port Filtering Setup ............................................................................................... 84
8.2.1 IP/Port Filtering .................................................................................................. 84
8.2.2 IPv6/ Port Filtering .............................................................................................. 86
8.3 URL Filter ................................................................................................................. 87
8.3.1 URL Blocking Configuration ................................................................................. 87
8.4 ACL Setup ................................................................................................................. 88
8.4.1 ACL Configuration ............................................................................................... 88
8.4.2 IPv6 ACL Configuration ....................................................................................... 89
8.5 DoS Setting .............................................................................................................. 90
9. Maintenance Setup ........................................................................................................ 91
9.1 Upgrade ................................................................................................................... 91
9.1.1 Upgrade Firmware .............................................................................................. 91
9.1.2 Backup/Restore Settings ...................................................................................... 92
9.2 Password .................................................................................................................. 94
9.2.1 User Account Configuration ................................................................................. 94
9.3 Reboot ..................................................................................................................... 95
9.3.1 Commit/Reboot ................................................................................................... 95
9.4 Time Setup ............................................................................................................... 96
9.4.1 System Time Configuration .................................................................................. 96
9.5 Log Setup ................................................................................................................. 97
9.5.1 Log Setting ......................................................................................................... 97
DG-BG4300N User Manual
9.6 Diagnostic Setup ....................................................................................................... 98
9.6.1 Ping Diagnostic ................................................................................................... 98
9.6.2 Ping6 Diagnostic ................................................................................................. 98
9.6.3 Traceroute Diagnostic .......................................................................................... 99
9.6.4 OAM Fault Management – Connectivity Verification ............................................... 99
9.6.5 ADSL Diagnostic................................................................................................ 100
9.6.6 Diagnostic Test ................................................................................................. 101
Troubleshooting ............................................................................................................... 102
DG-BG4300N User Manual
1. Product Information
1.1 Introduction and Safety Information
The DG-BG4300N supports Annex A mode. It provides four 10/100 Base-T Ethernet ports for user. The device provides high-speed ADSL2+ broadband connection to the Internet or Intranet for high-end users, such as net bars and office users.
It provides high performance access to the Internet, downstream up to 24 Mbps and upstream up to 1 Mbps. The device supports WLAN access to the Internet, such as WLAN AP or WLAN device. It complies with IEEE 802.11b/g, IEEE 802.11n specifications, WEP, WPA, and WPA2 security specifications.
You can configure the router by running the Setup Wizard in the CD-ROM provided in the package. The wizard provides quick setup for Internet and Wireless connection. When you start the Setup Wizard, Please follow the easy steps in Quick Installation Guide.
1.2 Other features of the router
High Internet Access throughput. Downstream at 24 Mbps and Upstream at 1 Mbps. Wireless speed up to 300Mbps. Allows multiple users to share a single xDSL internet connection. Access private LAN servers from the internet. Four wired LAN ports (10/100M) and one WAN port (RJ-11). Works with IEEE 802.11b/g/n wireless LAN devices. Supports IPv6. Supports DHCP (Server/Client) for easy IP-address setup.
DG-BG4300N User Manual
1.3 Safety Information
In order to keep the safety of users and your properties, please follow the safety instructions as mentioned below:
1. This router is designed for indoor use only; DO NOT place this router outdoor.
2. DO NOT place this router close to a hot or humid area, like kitchen or bathroom. Also, do not leave this router in the car during summer.
3. DO NOT pull any connected cable with force; disconnect it from the router first.
4. If you want to place this Router at a height or mount on the wall, please make sure it is firmly secured. Falling from a height would damage the router and its accessories and warranty will be void.
5. Accessories of this router, like antenna and power supply, are dangerous to small children. KEEP THIS ROUTER OUT OF THE REACH OF CHILDREN.
6. The Router will get heated up when used for long time (This is normal and is not a malfunction). DO NOT put this Access Point on paper, cloth, or other flammable materials.
7. There’s no user-serviceable part inside the router. If you find that the router is not working properly, please contact your dealer of purchase and ask for help. DO NOT disassemble the router, warranty will be void.
8. If the router falls into water when it’s powered, DO NOT use your hands to pick it up. Switch the electrical power off before you do anything, or contact an experienced electrical technician for help.
9. If you smell something strange, or even see some smoke coming out from the router or power supply, remove the power supply or switch the electrical power off immediately, and call dealer of purchase for help.
DG-BG4300N User Manual
1.4 System Requirements
Notebook or desktop computer with network adapter (wired/wireless)  Internet connection, provided by xDSL or cable modem with a RJ-45 Ethernet port.  Web browser (Microsoft Internet Explorer 4.0 or above, Netscape Navigator 4.7 or above, Opera
web browser, or Safari web browser).
An available AC power socket (100 – 240V, 50/60Hz)
1.5 Package Contents
Before you start using this router, please check if there’s anything missing in the package, and contact your dealer of purchase to claim for missing items:
DG-BG4300N ADSL2+ Wireless Broadband Router Switching power adapter (9V DC, 1A) Rubber feet (4 Nos.) Quick Installation Guide Installation software CD (includes User Manual, Utility) Patch chord (1 No.)
DG-BG4300N User Manual
LED
Color
Status
Description
Power Red
ON
Device is initializing or initialization is failed
Green OFF
Power is OFF
ON
Power is ON
WPS
Green Blinking
WPS negotiation is enabled, waiting for the clients
OFF
WPS negotiation is not enabled on the device.
WLAN
Green ON
WLAN connection is normal.
Blinking
Data is being transmitted or received.
OFF
Wireless is not enabled
LAN (1~4)
Green ON
LAN connection is normal.
Blinking
Physical link is UP.
OFF
LAN port is not in use.
ADSL
Green ON
Physical link is UP.
Blinking
ADSL handshaking process is ON.
OFF
No ADSL signal is being detected.
Internet
Green ON
Internet connection is established.
Blinking
Data is being transmitted or received.
OFF
Device is not connected to Internet.
1.6 Get Familiar with your new ADSL2+ Wireless broadband router
Front Panel
Interfaces
Description
Antenna
It is a 2dBi dipole antenna.
Radio
ON/OFF
Switch the button to activate or deactivate the wireless functions.
WPS
Press this button for less then 5 seconds to start WPS function.
Reset
Press this button and hold for 10 seconds to restore all settings to factory defaults.
LAN (1~4)
Local Area Network (LAN) ports 1 to 4.
Line (WAN)
(WAN / Internet) port. Connect ISP line to the Line port.
Power
Power connector, connects to A/C power adapter.
Rear Panel
DG-BG4300N User Manual
DG-BG4300N User Manual
2. System and Network Setup
2.1 Hardware Installation
Step 1 Connect the Line interface of the device and the Modem interface of the splitter with a
telephone cable. Connect the phone set to the Phone interface of the splitter through a telephone cable. Connect the input cable to the Line interface of the splitter.
Step 2 Connect all your computers, network devices (switch / hub) to the LAN port of the router.
DG-BG4300N User Manual
Step 3 Connect the power adapter (9V DC / 1A) to the wall socket, and then connect it to the ‘Power’ socket of the router.
Step 4 Please check all LEDs on the front panel. Power LED ‘should be steadily ON, ADSL and LAN should be ON. Check if the computer / network device connected to the respective port of the router is powered ON and correctly connected. If power LED ‘P’ is not ON, or any LED you expected is not ON, please recheck the cabling.
DG-BG4300N User Manual
3. Software Installation
Step 1: Insert the Setup CD into your CD-ROM drive of notebook/desktop computer.
Step 2 : You will see the Autorun utilit. Click ‘Start’ to continue.
DG-BG4300N User Manual
Step 3 : Connect one end of the telephone cable RJ-11 into the ADSL port provided on the splitter from the service provider and connect other telephone cable from the splitter to the LINE port on the router. Click ‘Next’ to continue.
DG-BG4300N User Manual
Step 4 : Power ON the router. It will take approximately 30 seconds for router to boot up completely. Ensure that all the LED’s on the router are ON. If not, try the above steps again else click ‘Next’ to
continue.
Step 5 : Connect one end of the network cable to one of the LAN ports (1~4) of the router and the other
end to your computer. Click ‘Next’ to continue with the installation.
Step 6 : On this page, you can view the description of LED indicators.
DG-BG4300N User Manual
Step 7 : If the LED indications are proper click ‘Next’ to continue with the installation.
Step 8 : Here, you can configure the ADSL router. Select the Country : India and then select the service
provider from the drop-down list. You can change the VPI/VCI value as instructed by your ISP.
DG-BG4300N User Manual
VPI : The valid value is in the range of 0 to 255 VCI : The valid value is in the range of 32 to 65535. (0 to 31 is reserved for local management of
ATM traffic).
Note : If ISP you are looking for is not listed in the dropdown list, then you can add the parameters manually, select ‘User defined’ in the Country and enter the Service Provider with correct VPI/VCI values.
DG-BG4300N User Manual
Step 9 : Click ‘Next’ to continue with the installation.
You can select LLC or VC-Mux as the encapsulation mode according to the uplink equipment or use the default setting.
1483 Bridged : If you select 1483 Bridged as the WAN protocol, you must use the third party
Dial-up software or Windows New Connection Wizard to configure the Internet dial-up access.
1483 MER : If you select 1483 MER as the WAN protocol, the router obtains an IP address
automatically.
1483 Routed : If you select 1483 Routed as the WAN protocol, you can not use the DHCP
service. You need to enter the IP address, subnet mask, default gateway and DNS that is provided by your ISP.
PPPoE /PPPoA : If you select PPPoE or PPPoA as the WAN protocol, click Next, and the
following page appears.
Step 10 : In this page, enter the correct user ID and password that is provided by your ISP. After settings, click ‘Next’ to continue with the installation.
DG-BG4300N User Manual
Following page appears showing the WAN status.
DG-BG4300N User Manual
Note: If the WAN IP address appears 0.0.0.0, then click Retry for retrying the connection to Internet. If a valid IP address appears, other than 0.0.0.0, then click Finish to complete the configuration.
Click ‘Next’ to continue with the installation. Step 11 : In this page, you can set the SSID for wireless network.
Step 12 : Click ‘Next’ and the following page appears. In this page, you can select WEP or WPA-PSK
/WPA2-PSK as the security mode. Enter 5 characters for WEP key. And enter 8~63 characters for WPA-
DG-BG4300N User Manual
PSK key. For more information about wireless security, refer to the user manual.
Step 13 : Click ‘Next’ and the following page appears. In this page, you can view the configuration summary.
Step 14 : Click ‘Finish’ to save your settings and reboot the router.
DG-BG4300N User Manual
4. Web Browser Configuration
The DSL device is an ADSL2+ wireless router. When you power on the device, the system will boot up and connect to ADSL automatically. The system provides a PVC for bridge test by default. The default configurations for the system are listed below.
LAN IP address: 192.168.1.1, Netmask: 255.255.255.0 Default VPI/VCI for ATM (maximum 8 sets): 0/32, 1/32, 0/35 ADSL Line mode: Auto-detect.
User can change settings via WEB browser. The following sections describe the set up procedures. Please set your PC’s Ethernet port as follow:
IP address: 192.168.1.XXX (e.g. 192.168.1.10) Netmask: 255.255.255.0
DG-BG4300N User Manual
Access the Web Console:
Start your web browser.  Type the Ethernet IP address of the modem/router on the address bar of the browser. Default
IP address is 192.168.1.1.
Enter Password in the dialog box when it appears. Default Username: admin Password: 1234
DG-BG4300N User Manual
Once you have connected to ADSL2+ router. You will see the status page.
This page displays the ADSL modem/router’s current status and settings. This information is read-only except for the PPPoE/PPPoA channel for which user can connect/disconnect the channel on demand. Click the “Refresh” button to update the status
Function buttons in this page:
Connect / Disconnect The two buttons take effect only when PVC is configured as PPPoE/PPPoA mode. Click
Connect/Disconnect button to connect/disconnect the PPP dial up link.
DG-BG4300N User Manual
To view the ADSL Configuration Status please click on “ADSL”.
To view the ADSL Statistics please click on “Statistics”.
DG-BG4300N User Manual
DG-BG4300N User Manual
5. Setup
5.1 WAN Configuration
There are three sub-menu for WAN configuration: [Channel Config], [ATM Settings], and [ADSL Settings].
Channel Config ADSL modem/router supports 8 ATM Permanent Virtual Channels (PVCs). There are mainly three operations for each of the PVC channels: add, delete and modify. And there are several channel modes to be selected for each PVC channel. For each of the channel modes, the setting is quite different accordingly. Please refer to the section – Channel Mode Configuration for further details.
DG-BG4300N User Manual
Function buttons in this page:
Add Click Add to complete the channel setup and add PVC channel into configuration.
Modify
Select an existing PVC channel by clicking the radio button at the Select column of the Current ATM VC Table before we can modify the PVC channel. After selecting PVC channel, we can modify the channel configuration at this page. Click Modify to complete the channel modification and apply to the configuration.
Delete
Select an existing PVC channel to be deleted by clicking the radio button at the Select column of the Current ATM VC Table. Click Delete to delete this PVC channel from configuration.
DG-BG4300N User Manual
Field
Description
VPI
Virtual Path Identifier. This is read-only field and is selected on the Select column in the Current ATM VC Table.
VCI
Virtual Channel Identifier. This is read-only field and is selected on the Select column in the Current ATM VC Table. The VCI, together with VPI, is used to identify the next destination of a cell as it passes through the ATM switch.
5.1.1 ATM Settings
The page is for ATM PVC QoS parameters setting. The DSL device support 4 QoS mode —CBR/rt­VBR/nrt-VBR/UBR.
Fields in this page:
DG-BG4300N User Manual
QoS
Quality of Service, a characteristic of data transmission that measures how accurately and how quickly a message or data is transferred from a source host to a destination host over a network. The four QoS options are: UBR (Unspecified Bit Rate): When UBR is selected, the SCR and MBS fields are disabled. CBR (Constant Bit Rate): When CBR is selected, the SCR and MBS fields are disabled. nrt-VBR (non-real-time Variable Bit Rate): When nrt-VBR is selected, the SCR and MBS fields are enabled. rt-VBR (real-time Variable Bit Rate): When rt-VBR is selected, the SCR and MBS fields are enabled.
PCR
Peak Cell Rate, measured in cells/sec, is the cell rate which the source may never exceed.
SCR
Sustained Cell Rate, measured in cells/sec, is the average cell rate over the duration of the connection.
MBS
Maximum Burst Size, a traffic parameter that specifies the maximum number of cells that can be transmitted at the peak cell rate.
Function buttons in this page:
Apply Changes
Set new PVC OoS mode for the selected PVC. New parameters will take effect after saving into flash memory and reboot the system. See section “Admin” for save details.
Undo Discard your settings.
5.1.2 ADSL Settings
The ADSL setting page allows you to select any combination of DSL training modes.
Loading...
+ 73 hidden pages
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use