Digisine Energytech 101029185569 User Manual

Features

■ Bluetooth® v4.1 specification

■ 7.5dBm Bluetooth low energy maximum transmit

output power

■ -92.5dBm Bluetooth low energy receive sensitivity

■ Support for Bluetooth v4.1 specification host stack

including ATT, GATT, SMP, L2CAP, GAP

■ RSSI monitoring for proximity applications

■ <900nA current consumption in dormant mode

■ 32kHz and 16MHz crystal or system clock

■ Switch-mode power supply

■ Programmable general purpose PIO controller

■ 10-bit ADC

■ 11 digital PIOs

■ 3 analogue AIOs

■ UART

■

I²C / SPI for EEPROM / flash memory ICs and

peripherals

■ Debug SPI

■ 4 PWM modules

■ Wake-up interrupt and watchdog timer

General Description

BDP-1010 are single-mode Bluetooth low

energy products for the Bluetooth Smart market.

BDP-1010 increases application code and data

space for greater application development flexibility.

BDP-1010 enables ultra low-power connectivity and

basic data transfer for applications previously limited by

the power consumption, size constraints and complexity

of other wireless standards. BDP-1010 provides

everything required to create a Bluetooth low energy

product with RF, baseband, MCU, qualified Bluetooth

v4.1 specification stack and customer application

running on a single module

Applications

■ Bluetooth low energy takes less time to make a

connection than conventional Bluetooth wireless

technology and can consume approximately 1/20

the power of Bluetooth Basic Rate. BDP-1010

supports profiles for health and fitness sensors,

watches, keyboards, mice and remote controls.

Typical Bluetooth Smart applications:

■ HID: keyboards, mice, touchpads, remote controls

■ Sports and fitness sensors: heart rate, runner

■ Health sensors: blood pressure, thermometer and

■ Mobile accessories: watches, proximity tags, alert

■ Smart home: heating control and lighting control

BDP-1010 BLE Module

Bluetooth Module

Production Information

th

of

speed and cadence, cycle speed and cadence

glucose meters

tags and camera controls

FCC Statement

This device complies with Part 15 of the FCC rules standard. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that

may cause undesired operation.

This device and its antenna(s) must not be co-located or operating in conjunction with
any other antenna or transmitter.

This module is intended for OEM integrator. The OEM i
compliance to all the rules that apply to the product into which this certified RF module
is integrated. Additional testing and certification may be necessary when multiple
modules are used.

In the users manual of the end product, the end user has to be informed to keep at
least 20cm separation with the antenna while this end product is installed and
operated.
The end user has to be informed that the FCC radio-frequency exposure guidelines
for an uncontrolled environment can be satisfied.
The end user has to also be informed that any changes or modifications not expressly
approved by the manufacturer could void the user's authority to operate this
equipment.
Operation is subject to the following two conditions: (1) this device may not cause
harmful interference and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Changes or modifications to this unit not expressly approved by the party responsible
for compliance could void the user authority to operate the equipment.
Referring to the multi-transmitter policy, multiple-transmitter(s) and module(s) can be
operated simultaneously without C2PC.

ntegrator is responsible for the

LABEL OF THE END PRODUCT:

The final end product must be labeled in a visible area with the following " Contains
TX FCC ID: VLV101029185569 ".

NCC Warning Statement

Article 12
Without permission, any company, firm or user shall not alter the frequency,
increase the power, or change the characteristics and functions of the original
design of the certified lower power frequency electric machinery.
Article 14
The application of low power frequency electric machineries shall not affect the
navigation safety nor interfere a legal communication, if an interference is
found, the service will be suspended until improvement is made and the
interference no longer exists.