Digi-Sense 94461-01 User manual

SPECIFICATIONS

Timing Capacity: 99 minutes, 59 seconds
Timing Accuracy: ±0.01%

COUNTDOWN ALARM TIMING

1. Clear the display to zero.

2. Press the MIN (minutes) button to advance the
minutes digits. Press and hold down the MIN
button to rapidly advance the minutes.

3. Press the SEC (seconds) button to advance the
seconds digits. Press and hold down the SEC
button to rapidly advance the seconds.

4. Once the desired time is on the display, press the
START/STOP button to begin countdown timing.

5. When the timer reaches zero, an alarm will sound
and the timer will begin counting up.

The alarm will sound for one minute and then turn off
automatically to preserve battery life while the timer
continues counting up.

While the alarm is sounding, pressing the
START/STOP button will silence the alarm, stop the
count-up timing, and recall the last programmed
time. After one minute, pressing the START/STOP
button will stop the count-up timing and recall the last
programmed time.

MEMORY RECALL

When timing repetitive intervals, the memory function
will recall the last programmed time. This feature
allows the timer to be dedicated to a frequently timed
test. The timer will return to the last programmed time
again and again.

1. Follow steps 1 through 5 in the “Countdown Alarm
Timing” section.

2. When the alarm starts, press the START/STOP
button to stop the alarm and recall the last
programmed time.

4. Press the START/STOP button a again to begin
countdown timing.

CLEARING THE DISPLAY TO ZERO

If an error is made during an entry, press the MIN
and SEC buttons simultaneously to clear the display
to zero. If you wish to clear the display to zero when

WLPHLVUXQQLQJ\RXPXVW¿UVWVWRSWKHWLPLQJE\

pressing the START/STOP button, then press the MIN
and SEC buttons simultaneously. The timer will only
clear when time is stopped.

STOPWATCH (COUNT-UP) TIMING

1. Clear the display to zero.

2. Press the START/STOP button to begin
count-up timing.

3. Press the START/STOP button to stop
count-up timing.

Once timing is completed and the timer has
been stopped, press the MIN and SEC buttons
simultaneously to clear the display to zero.

TIMEOUT

The timer may be stopped during any running time
by pressing the START/STOP button. Timing may
be resumed by pressing the START/STOP button a
second time.

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

CONVERT A TIMEOUT TO A COUNTDOWN TIME

The timer may be stopped during any running time
(countdown or count-up) by pressing the START/
STOP button. Once the timing has been stopped,
pressing the MIN or SEC button will increment the
display from the point that it was stopped and will set
the timer into countdown mode. Once the desired
time is on the display, press the START/STOP button
to begin countdown timing.

ALL OPERATIONAL DIFFICULTIES

If this timer does not function properly for any reason,
replace the battery with a new high quality battery
(see the “Battery Replacement” section). Low
battery power can occasionally cause any number

RI³DSSDUHQW´RSHUDWLRQDOGLI¿FXOWLHV5HSODFLQJWKH

battery with a new fresh battery will solve

PRVWGLI¿FXOWLHV

BATTERY REPLACEMENT

$QLQFRUUHFWGLVSOD\QRGLVSOD\RURSHUDWLRQDOGLI¿FXOWLHV

indicate that the battery should be replaced. Slide
open the battery cover on the back of the timer. Insert
a new AAA alkaline battery. Make certain to note the
proper polarity as indicated by the diagram in the
battery compartment. Replace the battery cover.

©2014 92-5011-40 Rev. 0 081414

TRACEABLE
GIANT-DIGIT

COUNTDOWN

TIMER

INSTRUCTIONS

®

™

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com