SPECIFICATIONS:
Display: ⅝" high 4 digit LCD
Range: –40 to 2000°F (Fahrenheit Model)
–40 to 1200°C (Celsius Model)
Accuracy Chart:
Fahrenheit Model Celsius Model
Range Accuracy ± Range Accuracy ±
32 to 932 °F 0.75% + 2 °F 0 to 500 °C 0.75% + 1 °C
933 to 1382 °F 1% + 2 °F 501 to 750 °C 1% + 1 °C
1383 to 1832 °F 2% + 2 °F 751 to 1000 °C 2% + 1 °C
1833 to 2000 °F 4% + 2 °F 1001 to 1200 °C 4% + 3 °C
31 to –4 °F 4 °F 0 to 20 °C 2 °C
–5 to –40 °F 6 °F –21 to –40 °C 3 °C
Resolution: 1°
Update Rate: Less than 1 second
Probes: Ultra-fast response, naked bead
type-K thermocouple
Case: ABS plastic
Fail safe: Low battery indicator
Power: 9 volt alkaline battery
Accessories
supplied: Integrated stand and PVC pouch
with carrying strap
PROBE
The probes supplied are ultra-fast response, naked bead
type-K thermocouples. Operating temperature range
for this thermocouple is the 482 °F (250 °C), and short
term usage to 572 °F (300 °C). Accessory probes are
available for measuring temperatures throughout the
entire range of this unit. (See Accessories)
Longer leads and extensions may be used.
The lead effect for 164 feet (50 meters) is generally less
than 0.2° C with a limit of error of 2.2 °C. Type-K wire
and type-K connectors must be used.
OPERATION
Insert the sensor plug into the socket (T1 or T2). The plug
and socket are keyed with a small and large pin. Make
certain the plug is inserted correctly, do not insert the
plug incorrectly and force it.
Slide the OFF/T1/T2 switch to T1 to display the
temperature of T1, or to T2 to display the temperature of
T2. If there is no probe (an open condition) the display
will indicate 1 on the left side.
Place the probe tip in contact with the material to be
measured and read the temperature on the display.
Slide the OFF/T1/T2 switch to OFF to turn the unit off.
To conserve battery life, always turn the unit off when not
in use.
ACCESSORIES
Cat. No. 4014–
Stainless Steel Triple Purpose Probe, probe diameter ⅛″
(0.32 cm), probe length 6″ (15.2 cm), overall length 9″
(22.9 cm), cable length 50″ (127 cm).
Cat. No. 4008–
Surface Probe, at disk on end has diameter of 0.39″ (1
cm), overall length 9″ (23 cm), cable length 36″ (91.4 cm).
Cat. No. 4028–
Ultra-fast response, naked bead thermocouple, (identical
to probe supplied with unit) cable length 48″ (122 cm).
ALL OPERATIONAL DIFFICULTIES
If this thermometer does not function properly for any
reason, please replace the battery with a new high quality
battery (see “Battery Replacement section). Low battery
power can occasionally cause any number of “apparent”
operational difculties. replacing the battery with anew
fresh battery will solve difculties
BATTERY REPLACEMENT
LO BAT appearing on the display indicates that the
battery should be replaced. To replace the battery, slide
the battery cover, located on the back of the unit, in
the directions of the arrow (away from the instrument).
Remove the exhausted battery and replace it with a new
9 volt alkaline battery. Replace the battery cover.
Find Qua lity Produ cts Onlin e at: sales@Gl obalTestSupply.c om
www.GlobalTestSupply.com
©2014 92-4025-40 Rev. 0 280814
Find Qua lity Produ cts Onlin e at: sales@Gl obalTestSupply.c om
www.GlobalTestSupply.com
TRACEABLE
EXPANDED RANGE
THERMOMETER
INSTRUCTIONS
®
Loading...