Digi-Sense 20250-11 User manual

User Manual

Thermohygrometer

with NIST-Traceable Calibration

Model 20250-11

3

3

THE STANDARD IN PRECISION MEASUREMENT

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

www. .com

[e-mail]1.800.561.8187

Introduction

The Digi-Sense Thermohygrometer (Model 20250-11) offers
fast response and high accuracy. This device measures
humidity (relative and absolute), temperature, plus it
calculates dew point and wet bulb. Advanced features
include data Hold, Min/Max readings, and automatic
power-off. The instrument is fully tested and calibrated to
NIST-traceable standards. Careful use of this meter will
provide years of reliable service.

Unpacking

Check individual parts against the list of items below. If
anything is missing or damaged, please contact your
instrument supplier immediately.

1. Meter

2. Carrying case

3. Three AAA batteries

4. User manual

5. NIST-traceable calibration report with data

2

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

Meter Description

1. Humidity/temperature sensor

2. LCD

3.

Power on/off button

4. MODE button

5.

Backlight button

6. °C/°F button

7. HOLD button

8. MIN/MAX button

1

5

4

3

2

3

3

6

7

8

3

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

Display Layout

1. Relative humidity unit

2. Absolute humidity unit (grams per cubic meters)

3. Absolute humidity (grains per cubic feet)

4. Humidity displayed reading

5. °C temperature unit

6. °F temperature unit

7. Dew point icon

8. Wet bulb icon

9. Hold icon

10. Minimum reading icon

11. Maximum reading icon

12. Low-battery indication

13. Auto power-off icon

14. Temperature / DP / WB displayed reading

15. Absolute humidity icon

Note: Display has additional units (GPP and g/kg)
for absolute humidity measurements.

2 3

1

4

15

14

5
6

7
8

4

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

13 12 11 10 9

Setup and Operation

Power

Press the Power on/off button to turn unit on.

Taking Measurements

1. Hold the probe in the area to be tested.

2. Allow adequate time for readings to
stabilize.

3. Press the MODE button to toggle
between humidity measuring units
(shown on top display): %RH, GPP,
g/kg, g/m

4. Press the °C/°F button to toggle between temperature
measuring units (shown on bottom display): °C, °F,

Dew Point (DP), or Wet Bulb (WB).

Absolute Humidity Measurements

1. To select the Absolute Humidity
measurement, press the MODE button
until g/m
on the screen.

2. Absolute humidity is now shown in
upper display.

Temperature Measurements

1. To select the temperature measure­ment, press the °C/°F button until the
°C or °F icon appears in the lower
right.

2. Temperature is now shown in lower
display.

3

, or gr/ft3 .

3

(or gr/ft3) and abs appears

5

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

Setup and Operation (continued)

Dew Point Measurements

1. To select the Dew Point measurement,
press the °C/°F button until the DP (°C)
or DP (°F) icon appears in the lower
right.

2. Dew Point temperature is now
shown in lower display.

Wet Bulb Measurements

1. To select the Wet Bulb measurement,
press the °C/°F button until the WB (°C)
or WB (°F) icon appears in the lower
right.

2. Wet Bulb temperature is now shown
in lower display.

Data Hold Function

1. Press HOLD button to freeze the dis-
played readings. The HOLD icon appears
on the lower right-hand side of the
screen.

2. Press HOLD button again to return to
normal operation.

6

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

Setup and Operation (continued)

Viewing the Min and Max Readings

The MIN/MAX mode allows the user to view only
the lowest (MIN) or highest (MAX) reading.

1. Press MIN/MAX button once and the
MIN icon appears on bottom of screen.
The LCD is now displaying the minimum
reading of the selected parameter in the
display. The display will not change until
a lower reading is registered.

2. Press MIN/MAX button again and the
MAX icon appears on bottom of screen.
The LCD is now displaying the maxi­mum reading of the selected parameter
in the display. The display will not change
until a higher reading is registered.

3. Press MIN/MAX button again to exit the
MIN/MAX mode.

Note: While powering on the meter each time, it
restarts recording Minimum and Maximum, and the
recordings don’t stop until the meter is turned off.

7

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

Setup and Operation (continued)

LCD Backlight

Press Backlight button to turn on the backlight. Press again
to turn off the backlight.

Automatic Power-Off

To conserve battery life, the meter automatically turns off
after 10 minutes (indicated by the icon on the screen). To
disable this feature:

1. Turn the meter off.

2. Press and hold the HOLD button while powering on.

3. “dis AUP” will appear in the display and the Auto power­off icon will no longer be shown, indicating that the Auto
power-off feature is disabled.

4. Note that Auto power-off is re-enabled each time the
meter is turned on.

8

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

Specifications

Range

Humidity 0 to 100% RH

Absolute humidity
(calculated)

Temperature –22 to 212°F (–30 to 100°C)

Dew point (calculated) –22 to 212°F (–30 to 100°C)

Wet bulb (calculated) 32 to 176°F (0 to 80°C)

0 to 500 g/m
0 to 218.5 gr/ft

Resolution

Humidity 0.1

Temperature 0.1°F/C

Accuracy

Humidity ±2% RH from 40 to 60% RH

Temperature ±0.9°F (0.5°C) from –4 to 140°F (–20 to 60°C)

±3% RH from 20 to 40% RH and 60 to 80% RH
±4% RH from 0 to 20% RH and 80 to 100% RH

±1.8°F (1°C) from –22 to –4°F (–30 to 19°C)
and 140 to 212°F (60 to 100°C)

3

3

9

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

Specifications (continued)

Display Dual LCD

Response time <15 sec (90% of final value in moving air)

Sensors Humidity: precision capacitance;

Auto power-off Unit shuts off automatically after 10 minutes

Operating temperature 32 to 122°F (0 to 50°C)

Operating humidity <80% RH, noncondensing

Storage temperature –40 to 185°F (–40 to 85°C)

Storage humidity <99% RH, noncondensing

Weight 14 oz (400 g)

Dimensions 6

Power Three AAA 1.5 V batteries

Battery life Typically 48 hrs. Battery life will be reduced

Temperature: thermistor

to preserve battery life

1

⁄2" x 21⁄8" x 13⁄8" (16.5 x 5.4 x 3.4 cm)

significantly if the automatic backlight is used
continuously.

10

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

Maintenance, Recalibration, and Repair

Cleaning and Storage

• The meter should be cleaned with a damp cloth and

mild detergent when necessary. Do not use solvents
or abrasives.

• Store the meter in an area with moderate temperature

and humidity (refer to the operating and storage range
in the specifications chart earlier in this manual).

Battery Replacement

When the battery power falls low, the Low Battery icon
will appear on the screen. Replace the three AAA batter­ies by removing the screw holding the rear battery
compartment cover to access the battery compartment.
Ensure that the compartment cover is securely fastened
when finished.

It is recommended that Digi-Sense products are cali­brated annually to ensure proper function and accurate

measurements; however, your quality system or regula­tory body may require more frequent calibrations. To
schedule your recalibration, please contact InnoCal, an
ISO 17025 calibration laboratory accredited by A2LA.

11

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com