DigiPower DPS-6000 User Manual

Page 1
DPS-6000
DPS-6000 is a new type intelligent charger with a LCD
of display. It has -dV, Vmax, Temperature and Timer protection. The charger has 2 independent channels and 2 or 4 Ni-MH batteries (AA or AAA) can be charged at the same time. It is convenient for home or travel as a portable compact charger.
AC 100-240V, 50/60Hz for adapter DC 12V,500mA for charger
Input plug for adapter
LCD indicates the charging status
Charger Indicator:
1) Charging: Battery indicator rolling
from 0 to 3
(2)
(3)
2) Charge finished: Battery indicator
remains constantly on:
Fault: Battery symbol flash (1/sec.):
3)
4) Power on but no batteries in
the charger:
(0) (1)
LCD Display
AC adapterBattery slot
Step 1. Load batteries into charger
1.This charger is designed to charge 2 or 4 AA or AAA Ni-MH rechargeable batteries.
2.If you want to charge 4 AA, or 2 AA and 2 AAA, put batteries into the charger compartments, taking care to observe polarity (+/-) as indicated inside the charger. (Fig.1)
Cut off temperature
Charging Time
11
Protection +/- polarity worng
connection
12
AA and AAA mixed
Alkaline
Average Trickle
13
current Dimension
14
Best Ambient
15
Temperature Approval type
16
5) Power off: LCD off
Ni-MH rechargeable battery AA/AAA battery
2 or 4 pcs AA/AAA 2 batteries can charge at left or right 2 channels
AA mini 2500mAh AAA mini 1000mAh
AA*2: 1500mA 250mA AA*4: 750mA 125mA (Pulse current Imax=1.5A 250mA, 50% duty, 1s on, 1s off) AAA*2: 350mA 100mA AAA*4: 350mA 50mA (Pulse current Imax=700mA 100mA, 50% duty, 1s on, 1s off)
0-24mV/Channel
3.4V 100mV/Channel
47-55
1 temperature sensor each Channel
120min 10% 2pcsAA
240min 10% 4pcsAA
180min 10% 2/4pcsAAA
No charging current
Charge as AAA battery No charging current
20-100mA
116mm(L)x75mm(W)x33.5mm(H)
20-25
AC Adapter: CETL Charger: FCC
Fig.1 Charging 4pcs of AA or AAA
3.If charging only 2 batteries at a time, place the batteries in the left or right side compartments of the charger.(Fig.2)
Fig.2 Charging 2pcs of AA or AAA
Page 2
Step 2. Plug in the charger
1.Connect the charger input plug with AC mains.
Step 3. Charging start and LCD indication
1.The LCD battery indicator rolls to indicate batteries are being charged. The LCD battery indicator remains constantly on to indicate batteries are fully charged.
2.The LCD battery symbol flashes to indicate charger is in fault mode.
3.No LCD light indicates the charger is in default mode.
4.The LCD indicating list is as follows:
No.
Status of LCD Status of charger
i ) Do not operate the charger if it has been subjected to shock or damage. Take it to a qualified service-man for repair. Not recommended for use by children.
j ) Do not disassemble the charger. Incorrect reassembly may result in a risk of electric shock or fire. Unplug the charger from outlet before attempting any maintenance or cleaning.
k) This power unit is intended to be correctly positioned in a vertical or floor mount position.
l ) For connection to a supply not in the U.S.A, use an attachment plug adapter of the proper configuration for the power outlet.
1
2
3
4
Roll ing
On
Flas hing
Off
Char ging
Full c harged
Faul t mode
Defa ult mode
Note: The charger will not supply charging current under
default mode.The default mode is due to the below cases: A. No battery put inside charger B. Battery connected with reverse-polarity C. The charger has an internal failure D. Power off
Step 4. End of Charging
1.When the charge time is completed, the batteries could be taken out and are ready for use.
2.Remove the charger from the AC mains.
3.Follow the process from step 1 if you want to start another charge.
Note: Proposed working temperature for charger: 20 C-25 C.
m) This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
n) Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
a) Before charging, read usage instructions.
b) This charger is designed for indoor use only. Do not expose to moisture or rain.
c) Please do not recharge non-rechargeable batteries.
d) This charger is intended to charge AA/AAA metal-hydride (Ni-MH) batteries only. Attempting to charge any other types of batteries may cause personal injury and damage.
e) This charger can charge 2 AA and 2 AAA at the same time.
f ) Do not mix Alkaline/Ni-MH, or different capacity batteries together to charge.
g) Remove charger from AC mains when not in use.
h) Never use an extension cord or any attachment not recommended by manufacturer. Otherwise, this may result in a risk of fire, electric shock or injury to persons.
Loading...