Digimerge VCE304161, VCE308161, VCE316161, VCE304, VCE308 User Manual

...

Download

Page 1

4/8/16 Channel Network DVR , 120 fps

Models VCE304, VCE308, VCE316

DIGIMERGE TECHNOLOGIES INC.

VCE300 SERIES MPEG4

Page 2

PRECAUTION

This symbol is intended to alert the user to the presence of unprotected “Dangerous voltage" within the product's enclosure that may be strong enough to cause a risk of electric shock.

This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

NOTE: This equipment has been tested and found to comply with the limits for a class digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Disposal of Old Electrical & Electronic Equipment

(Applicable in the European Union and other European countries with separate collection systems)

This symbol on the product or on its packaging indicates that this product shall not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. The recycling of materials will help to conserve natural resources. For more detailed information about recycling of this product, please contact your local city office , your household waste disposal service or the shop where you purchased the product.

Page 3

CONTENTS

All the safety and operating instructions must be read before the unit is operated.

• Make sure to switch the power off before you install the DVR.

• There is the danger of an electric shock if the DVR is opened by an unqualified service

engineer or installer.

• Avoid using the DVR outside of the reference temperature and humidity indicated in the

specification.

• Avoid exposing the DVR to violent movement or vibration.

• Do not use or store the DVR in direct sunlight or near to any source of heat.

• Do not place any object into the holes used for air circulation.

• Always use the DVR in a well ventilated location to prevent overheating.

• Risk of explosion if battery is replaced by an incorrect type.

• Dispose of used batteries according to the instructions.

• When the cooling fan is stopped, the below warning message will be displayed

at the monitor.

“ COOLING FAN IS STOPPED, TURN THE POWER OFF AND CHECK COOLING FAN”

In this case, do the power off right away and check the cooling fan working.

• The HDD is recommended to use enhanced IDE Hard Disc Drive type made by

Western Digital, Seagate, Hitachi and IBM, Samsung Electronics.

EXTERNAL HDD BAY (If specified as an accessory)

• Always attach the joining cable lead between the DVR and the HDD Bay for correct system

management. (Refer to the section describing the installation procedure for the EXTERNAL HDD BAY)

• While the EXTERNAL HDD BAY is in operation never disconnect the power or connecting

cable. Before opening the top cover, you must turn off the power by the switch on the front panel of the DVR. And then disconnect the power cord and other cables. Failure to follow this procedure will result in lost data or malfunction of the system.

• When replacing any HDD always make certain that the replacement part is fitted in the same

place and with the same connections as the original.

DIGITAL VIDEO RECORDER

Page 4

CONTENTS

TABLE OF CONTENTS

1. FEATURE LIST ----------------------------------------------------------------------------------

2. PACKING DETAIL ------------------------------------------------------------------------------------------

3. LOCATION AND CONTROL -----------------------------------------------------------------

3.1 FRONT PANEL CONTROLS -------------------------------------------------------------------------------

3.2 REAR PANEL CONNECTORS -----------------------------------------------------------------------------

4. INSTALLATION ---------------------------------------------------------------------------------------------

4.1 TOTAL CONNECTION LAY-OUT -------------------------------------------------------------------------

4.2 INDIVIDUAL CONNECTION --------------------------------------------------------------------------------

4.2.1 CAMERA ------------------------------------------------------------------------------------------

4.2.2 AUDIO ---------------------------------------------------------------------------------------------

4.2.3 MONITOR -----------------------------------------------------------------------------------------------

4.2.4 EXTERNAL HDD BAY --------------------------------------------------------------------------

4.2.5 USB 2.0 Ports -----------------------------------------------------------------------------------

5. OPERATION --------------------------------------------------------------------------------------

5.1 FACTORY DEFAULT ------------------------------------------------------------------------------

5.2 BUTTON CONTROLS -----------------------------------------------------------------------------

5.2.1 POWER ON / OFF --------------------------------------------------------------------------

5.2.2 SCREEN DISPLAY ------------------------------------------------------------------------------

5.2.3 RECORD ---------------------------------------------------------------------------------------

5.2.4 SEARCH & PLAYBACK ------------------------------------------------------------------

5.2.5 PLAY BUTTON INFORMATION ------------------------------------------------------------

5.2.6 DIGITAL ZOOM------------------------------------------------------------------------------------

5.2.7 SCREEN SELECT (LV/PB) ----------------------------------------------------------------------

5.2.8 SPOT MONITOR -----------------------------------------------------------------------------------

5.2.9 COPY ----------------------------------------------------------------------------------------------

5.2.10 DVR STATUS ------------------------------------------------------------------------------------

5.2.11 PTZ CONTROL ------------------------------------------------------------------------------------

5.2.12 FUNCTION BUTTON ---------------------------------------------------------------------------

5.2.13 AUDIO SELECT --------------------------------------------------------------------------------

5.3 REMOTE CONTROLLER -------------------------------------------------------------------------

5.4 MOUSE CONTROL --------------------------------------------------------------------------------

6. MENU SETUP ----------------------------------------------------------------------------------------------------

6.1 QUICK SETUP -----------------------------------------------------------------------------------------------

6.2 SCREEN ------------------------------------------------------------------------------------------------------

6.2.1 AUTO SEQUENCE ------------------------------------------------------------------------------

6.2.2 DISPLAY ---------------------------------------------------------------------------------------

6.2.3 TITLE -----------------------------------------------------------------------------------------

6.2.4 MULTI SCREEN ---------------------------------------------------------------------------------

6.2.5 COVERT ----------------------------------------------------------------------------------------------

6.2.6 SPOT ----------------------------------------------------------------------------------------------

10 11

12 13 13 13 14 14 16

20 20 20 22 23 28 29 29 30 31 32 33 34 37

41 41 43 45 46 47 48

Page 5

CONTENTS

6.3 RECORD ---------------------------------------------------------------------------------------------------------

6.3.1 RECORD SETUP -----------------------------------------------------------------------------------

6.3.2 RECORD PROGRAM -----------------------------------------------------------------------------

6.3.3 IMAGE QUALITY --------------------------------------------------------------------------------------

6.3.4 AUDIO RECORD -------------------------------------------------------------------------------------

6.3.5 OVERWRITE -----------------------------------------------------------------------------------------

6.3.6 PLAY MODE -----------------------------------------------------------------------------------------

6.3.7 BACKUP MODE --------------------------------------------------------------------------------------

6.3.8 HOLIDAY -------------------------------------------------------------------------------------------------

6.4 EVENT ------------------------------------------------------------------------------------------------------------

6.4.1 MOTION DETECTION -----------------------------------------------------------------------------

6.4.2 EVENT SCREEN MODE -------------------------------------------------------------------------

6.4.3 EVENT RECORD --------------------------------------------------------------------------------------

6.4.4 EVENT MESSAGE ---------------------------------------------------------------------------------

6.4.5 EVENT MESSAGE RESET -----------------------------------------------------------------------

6.4.6 EVENT BUZZER ------------------------------------------------------------------------------------

6.4.7 SENSOR INPUT --------------------------------------------------------------------------------------

6.4.8 RELAY OUTPUT -------------------------------------------------------------------------------------

6.5 SYSTEM ---------------------------------------------------------------------------------------------------------

6.5.1 HDD -----------------------------------------------------------------------------------------------------

6.5.2 CLOCK ------------------------------------------------------------------------------------------------

6.5.3 VIDEO STANDARD ---------------------------------------------------------------------------------

6.5.4 LANGUAGE -------------------------------------------------------------------------------------------

6.5.5 REMOTE CONTROL ID ---------------------------------------------------------------------------

6.5.6 KEY SOUND --------------------------------------------------------------------------------------------

6.5.7 ADVANCE SETUP ---------------------------------------------------------------------------------

6.5.7.1 PASSWORD CHECK ---------------------------------------------------------------

6.5.7.4 DVR MENU SET -----------------------------------------------------------------------

6.5.8 FIRMWARE UPGRADE --------------------------------------------------------------------------

6.6 LINK ----------------------------------------------------------------------------------------------------------------

6.6.1 NETWORK --------------------------------------------------------------------------------------------

6.6.2 RS232C ------------------------------------------------------------------------------------------------

6.6.3 RS485 --------------------------------------------------------------------------------------------------

6.6.4 PTZ ------------------------------------------------------------------------------------------------------

6.6.5 E-MAIL --------------------------------------------------------------------------------------------------

6.6.6 DYNAMIC DNS ----------------------------------------------------------------------------------------

6.7 SEARCH ----------------------------------------------------------------------------------------------------------

6.8 COPY -------------------------------------------------------------------------------------------------------------

6.9 EXIT -------------------------------------------------------------------------------------------------------------

49 49 50 58 59 59 60 60 60

60 61 62 62 62 62 62 63 64

65 65 67 68 68 69 69 69 70 71 72

73 73 76 76 77 77 80

DIGITAL VIDEO RECORDER

Page 6

FEATURES

7. EXTERNAL TERMINAL INFORMATION ---------------------------------------------------

7.1~2 RS-485 / T.ADJ -----------------------------------------------------------------------------------------

7.3~4 RELAYOUT / ALARM --------------------------------------------------------------------------------------

7.5~6 VGA / SERIAL ----------------------------------------------------------------------------------------------

7.7~8 ETHERNET/USB ---------------------------------------------------------------------------------------

8. SPECIFICATIONS ----------------------------------------------------------------------------

9. 256 CAMERA INTEGRATION SYSTEM --------------------------------------------------

10. HDD INSTALLATION ------------------------------------------------------------------------

10.1 INTERNAL HDD INSTALLATION -------------------------------------------------------------------

10.2 DVD±RW(or CD-RW) installation-------------------------------------------------------------------

11. NETWORK CLIENT VIEWER MANUAL----------------------------------------------

84 85 86 87

92 95

11.1 INSTALLATION OF NETWORK VIWER SOFTWARE ------------------------------------------

11.1.1 SYSTEM REQUIREMENT ---------------------------------------------------------------------

11.1.2 NETWORK ENVIRONMENT ------------------------------------------------------------------

11.1.3 INSTALLATION -----------------------------------------------------------------------------------

11.2 CONNECTING TO DVR ---------------------------------------------------------------------------------

11.2.1 ADD A NEW SITE INFORMATION --------------------------------------------------------

11.2.2 CHANGE THE SITE INFORMATION ------------------------------------------------------

11.2.3 DELETE THE SITE INFORMATION -------------------------------------------------------

11.2.4 CONNECT TO A DVR -----------------------------------------------------------------------

11.2.5 VIEWER SCREEN -----------------------------------------------------------------------------

11.3 DVR SEARCH ---------------------------------------------------------------------------------------------

11.4 HDD SEARCH ---------------------------------------------------------------------------------------------

11.5 FILE SEARCH -----------------------------------------------------------------------------------------------

11.6 ARRANGE THE SCREEN ------------------------------------------------------------------------------

11.7 OPTION -------------------------------------------------------------------------------------------------------------

11.8 CONTROL ---------------------------------------------------------------------------------------------------

11.8.1 SCREEN DISPLAY -----------------------------------------------------------------------

11.8.2 CONTROLLER ----------------------------------------------------------------------------

11.8.3 PTZ -------------------------------------------------------------------------------------------

11.8.4 SETUP --------------------------------------------------------------------------------------

11.8.5 STATUS -------------------------------------------------------------------------------------

11.8.6 PRINT ---------------------------------------------------------------------------------------------

11.8.7 COPY ----------------------------------------------------------------------------------------------

11.8.8 AUDIO IN -----------------------------------------------------------------------------------------

11.8.9 AUDIO OUT --------------------------------------------------------------------------------------

11.8.10 TIME SEARCH -----------------------------------------------------------------------------------

11.8.11 CALENDAR SEARCH ---------------------------------------------------------------------------

11.8.12 EVENT SEARCH -----------------------------------------------------------------------------------

11.8.13 TEXT SEARCH ---------------------------------------------------------------------------------

11.8.14 BLOCK SEARCH ------------------------------------------------------------------------------

11.8.15 LOG SEARCH -----------------------------------------------------------------------------------

11.9 KEY INFORMATION ------------------------------------------------------------------------------------

APPENDIX . USING THE DDNS SERVER FOR REMOTE CONNECTION ……………….

WARRANTY ………………………………………………………………………………………..

97 97 97 97

97 98 98 98 98 98

99 100

101

102

103 103 103 104 105 105 105 106 107 107 108 108 108 109 109 110 111 112 118

USER’S MANUAL

Page 7

FEATURES

Chapter 1 Features

Operation

Playback, recording, backup and transmission simultaneously Real time single or multi-screen display Pan & Tilt, 2X digital zoom and PIP display

Easy operation by IR remote controller, external keypad controller and USB 2.0 Mouse

Hidden camera option (covert) User-friendly setup menu and operation

Playback Multi-screen playback (Full/4/6/7/9/10/13/16 split) Search by date, time and camera

Preview window on event search mode

Playback mode(frame/ field) setup

Recording

Select of the recording quality grade for each channel

Individual camera frame rate can be set by user

The recording speed of max. 120 images per second (NTSC) Manual, schedule and event recording Pre & Post-alarm recording Select of the recording image size for each channel

4 channels audio recording

Select of the event mode for each channel

Network

Live and playback viewing Remote control on a networked PC with the exclusive client viewer (The viewer software is supplied for free.)

Flexible connections - 10/ 100 Mbps Ethernet

Up to 16 network users access simultaneously

Audio transmission between DVR and Client Dynamic IP is available

DIGITAL VIDEO RECORDER

Page 8

PACKING DETAIL

External storage

Automatic backup to selected backup HDD (Event backup/ Mirroring) Own external storage device to extend the HDD capacity You can install 10 HDDs in 1 external HDD Bay and connect up to 4 Bay with this DVR. (250GB X 40HDDs = 10TB, 500GB X 40HDD = 20TB, 1TB X 40HDD = 40TB)

Audio

4 channels audio recording in real time Audio channel select for each channel

Copy

USB 2.0 external HDD

USB 2.0 memory stick

CD-R/ CD-RW/ DVD±RW/ DVD-RAM (optional)

General

Software downloading facility via network and USB memory stick

Auto detection of PAL / NTSC

Built-in software Watchdog Automatic time adjustment through Network VGA output for PC monitor(Optional) Optional external CDRW or DVD±RW Loop-through connections Support of multiple Languages Graphic User Interface for the MENU screen Analog Spot

USER’S MANUAL

Page 9

Chapter 2 Packing Detail

2. Network Viewer Program CD

5. R-HDD Rack Key

8. Batteries

1. DVR

2. Network Viewer Program CD

3. User’s Manual

4. Remote Controller

5. R-HDD Rack Key

6. Rack Mounts

7. AC Adaptor & Power Cord

8. Batteries (For Remote Controller)

9. HDD Screws

1. DVR

3. User’s Manual

6 Rack Mounts

9. HDD Screws

FEATURES

4. Remote controller

7. AC Adaptor & Power Cord

DIGITAL VIDEO RECORDER

Page 10

LOCATION AND CONTROL

Chapter 3 Location and Control

3.1 FRONT PANEL CONTROLS

○1

○

○4 ○2

○

Name Description

 USB USB 2.0 port to use a USB memory stick, Mouse or USB external devices

 CHANNEL SELECT

 AUDIO SEL / 0 Audio select button / Button to select the camera or input the password

 (+10) Button to select the camera(+10)+(0~6) 10/11/12/13/14/15/16

 MULTI

 SPOT / ESC  MENU / Button to display the setup menu/ move to the upper direction

 LV / PB  ALARM RESET /

 / STATUS/ ( HOME )

 D-ZOOM /

 AUTO / F / ( - ) / A

 PIP / / CLEAR Button to control PIP function/ move to the lower direction/ TILT down in PTZ mode/

 FREEZE / F / ( + ) / B

 REC( )

 SLOW( )/

 PB / PAUSE( )/ (Z-)

 FAST( )/ / (Z+)

 DIRECTION( )

 COPY(AF)

 SEARCH(PRESET)

 PTZ/ BOOKMARK Button to control PTZ camera/ Bookmark marking button

 FUNCTION

 LED Display

 Remote Sensor

 R.HDD RACK

Buttons to select the camera or input the password

Multi-channel select button

Button to control spot monitor/ return to the previous menu/ Not use password

/ TILT up in PTZ mode

Button to convert the screen into real view mode or into playback mode

Button to release the event signal/ move the left direction/ PAN left in PTZ mode

Button to enter the next step/ display the status/ return to home position in PTZ mode

Button to control the digital zoom/ move to the right direction/ PAN right in PTZ mode

Button to begin the auto sequence mode/ decrease the value/ focus in PTZ mode/ Button to set the section repetition playback

Button to release the section repetition playback Button freeze image/ increase the value/ focus in PTZ mode/ Button to set the section repetition playback

Button to begin and stop recording

Button to slow down the playback speed/ Backward playback button in pause mode

Button to start the playback. If press again, a still picture is displayed during playback./ Zoom out of PTZ camera Button to speed up the playback speed/ Forward playback button in pause mode/ Zoom in of PTZ camera

Button to change the direction of playback/ Last Record backward playback

Button to display the copy menu/ automatically focus in PTZ mode

Button to display the search menu/ preset in PTZ mode

Relay4 User action(FUNCTION + “+” / “-“)/ PTZ speed control

Display of the status of power(POWER), HDD(HDD) and network(RX / TX)

Input sensor for the remote controller

Removable HDD rack (Option: Built-in CD-RW or DVD±RW)

○

USER’S MANUAL

Page 11

○3

LOCATION AND CONTROL

3.2 REAR PANEL CONNECTORS

○1

○

Name Description

○3

○

○15

○

○14 ○16

○16

○

○1 CAMERA IN

○2 CAMERA OUT

○3 SPOT

○

VIDEO OUT

○5 AUDIO IN

○6 AUDIO OUT

○7 ETHERNET

○8 USB1 / USB2

○9 VGA OUT

○10 SERIAL

○11 S-VIDEO OUT

○12 GROUND

○13 RS-485

○14 T-ADJ

○15 RELAY OUT

○16 ALARM IN

○17 POWER IN

○18 POWER SWITCH

BNC input ports for cameras

BNC output(looping) ports for cameras

BNC output port for spot monitor

BNC output port for the main monitor (Same as the RCA video output of the front panel)

Stereo Jack input ports for an audio signal(4CH Line input)

Stereo Jack output port for an audio signal

Port for 10/ 100Mbps Ethernet/ xDSL

USB 2.0 ports to use USB memory stick, Mouse or the external devices

Output port for the VGA monitor This DVR is compatible with TFT LCD monitor in PAL mode.

Connector for debugging. This DVR can be controlled by the other device through this connector(RS-232C).

Output port for the S-video output

Earth ground port to connect with the external devices

Terminal blocks of RS-485

Input and output terminal blocks for time synchronization among DVRs

4 relay output terminal blocks

Input terminal blocks for alarm signals

Socket for a 12V/5A power cord

AC Power switch

DIGITAL VIDEO RECORDER

Page 12

INSTALLATION

Chapter 4 Installation

4.1 TOTAL CONNECTION LAY-OUT

USER’S MANUAL

Page 13

INSTALLATION

4.2 INDIVIDUAL CONNECTION

4.2.1 Camera

• Connect a female BNC connector of each camera to a male BNC connector, “CAMERA IN” port.

• Connect the looping BNC output to other inputs as required

4.2.2 Audio (*Refer to the specification)

Audio Input

• AUDIO IN : Connect the RCA Line Jack of the relevant equipment (for example, a camera

with a built-in microphone) to the AUDIO IN port

Audio Output

• AUDIO OUT : Connect the RCA Line output to a monitor with a built-in speaker

NOTE

This DVR can be connected only with a line audio and not support a microphone for audio input and output. To record audio should be enable in the AUDIO setup at the MENU setup.

You can select audio channels regardless of cameras. ** Please refer to 5.2.13 AUDIO SELECT.

DIGITAL VIDEO RECORDER

Page 14

INSTALLATION

4.2.3 Monitor

• Connect the female BNC for monitor output.

• Connect the male Y/C cable socket for S-VIDEO monitor output.

USER’S MANUAL

Page 15

INSTALLATION

4.2.4 External HDD Bay

(USB output)

INSTALLATION PROCESS.

1) Turn off the power of DVR.

2) Connect the grounding conductor between DVR and external HDD bay.

3) Connect the USB cable between DVR and external HDD bay.

4) Connect the power cords of DVR and each external HDD bay.

5) Plug the power cords of DVR and each external HDD bay.

6) Turn the power of DVR on.

7) After booting the system automatically, press the STATUS button and check the system information of setting the HDD. (If the HDD is not recognized properly, turn the power of DVR off first and check the cable connections referring to user’s manual of external bay.)

CAUTION - Do not disconnect the external HDD Bay from DVR in normal operating condition.

NOTE - Please refer to the external bay manual for more information.

DIGITAL VIDEO RECORDER

Page 16

OPERATION

4.2.5 USB 2.0 ports

○1 Three USB ports are provided to connect a USB memory stick, One USB port is on the

front panel and the other two are on the rear panel.

○

A USB mouse can be connected to one of the ports. You can use the mouse to navigate

through the screens and menus much like you would on a computer.

INSTALLATION PROCESS.

Connect the desired device with DVR as the above pictures.

(For example, USB memory stick, mouse, external storage device etc.)

NOTE: You have to turn on the power of USB storage devices after DVR is booted completely.

USER’S MANUAL

Page 17

Chapter 5 Operation

5.1 FACTORY DEFAULT

* 16CH DVR

MENU Setup>

QUICK SETUP>

QUICK SETUP…………………….….…….…..…...OFF

IMAGE SIZE……………………….………………....720x240

RECORD FRAME……………………….……….…..60 EVENT……….…………………………...…………...ALL PRE RECORD TIME……….…………...….………..5SEC

POST RECORD TIME………………….…...……....10SEC

IMAGE QUALITY…..…………………………………HIGH AUDIO RECORD…………………………….……….OFF REMOTE CONTROL ID…………….…..……….…..ALL

SCREEN>

AUTO SEQUENCE

QUAD-A~E/ SIX/ SEVEN/ NINE-A~B/ TEN/ THIRTEEN/ SIXTEEN….3SEC ADD AUTO SINGLE….………………..…...OFF AUTO-SINGLE CH1~16………………..…..3SEC VIDEO LOSS SKIP..…………………….…..ON

DISPLAY

HDD FREE SPACE.……………….………..ON HDD FREE SPACE MODE..…...…………..GIGABYTE RECORD STATUS..………………………...ON CLOCK DISPLAY…………………..……..…ON DATE & TIME MODE..…………….……..… MM/DD/YY

TITLE DISPLAY………………………....…..ON

TITLE MODE…………………………..….....TEXT

BORDER COLOR.………………………..…WHITE REMOTE CONTROL ID..………….……..…OFF

TITLE

CH 1~CH 16………………………….……….CH 1~CH16

MULTI SCREEN

MULTI 4E………………………………….….2/ 4/ 6/ 8 MULTI 6……………………………………….1/ 2/ 3/ 4/ 5/ 6 MULTI 7……………………………………….1/ 2/ 3/ 4/ 5/ 6/ 7 MULTI 9B……………………………………..10/11/12/13/14/15/16/1/2 MULTI 10………………………………………1/ 2/ 3/ 4/ 5/ 6/ 7/ 8/ 9/ 10 MULTI 13………………………………………1/ 2/ 3/ 4/ 5/ 6/ 7/ 8/ 9/ 10/ 11/ 12/ 13

COVERT

CH 1~16………………………….….….……..OFF SELECT……………………………….……….LV&PB&NW COVERT TITLE DISPLAY……………………OFF

SPOT

SPOT MODE……………………….………….MANUAL SPOT SEQUENCE TIME….……………..…..3SEC VIDEO LOSS SKIP……………………………ON

OPERATION

DIGITAL VIDEO RECORDER

Page 18

RECORD>

EVENT>

SYSTEM>

OPERATION

RECORD SETUP

RECORD PROGRAM..…………………….....6

RECORD PROGRAM (Refer to 6.3.2) IMAGE QUALITY

RECORD QUALITY………………………........HIGH

AUDIO RECORD

AUDIO 1~4………………..…………………......OFF

OVERWRITE

OVERWRITE……....………………………..…..ON

DISK FULL WARNING……..……………….…..5%

PLAY MODE.…………………………………….….......FRAME

BACKUP MODE..……………………………….…........OFF

HOLIDAY

HOLIDAY RECORD………………………….….OFF

HOLIDAY SETUP(MM/DD) ………………..…..00/00

MOTION DETECTION

CHANNEL…………………………………...…...1

SENSITIVITY…………………………...….…….3 EVENT SCREEN MODE…………………...…….….…UNCHANGED EVENT RECORD.………………………….…..…..……OFF

EVENT MESSAGE..…………………………….……....OFF

EVENT MESSAGE RESET……………….……......…..5SEC

EVENT BUZZER..…………………………………..…...OFF SENSOR INPUT

SENSOR 01~16 INPUT TYPE..………………..NOT USED RELAY OUTPUT

CH 1~16: ALARM/ V-LOSS/ MOTION..…….…1/ 2/ 3

RELAY 1~3 OUTPUT TIME..……………...……1SEC

RELAY 4 SELECT.….………………….…..……POWER

HDD

HDD CONFIGURATION

REC HDD FORMAT……..…………………..……NO

BACKUP HDD FORMAT…………………………NO

CLOCK

TIME ADJUST

INTERNET TIME ADJUST...……….……OFF

DAYLIGHT SAVING TIME..…….….…....OFF

VIDEO STANDARD…………….………………………...NTSC LANGUAGE……………….………..………………….….ENGLISH REMOTE CONTROL ID.…………….………..………… ALL KEY SOUND…..………………….……………….……….ON ADVANCED SETUP

PASSWORD CHECK…………………….……….OFF SET PASSWORD

ADMIN PASSWORD…..…….……….…..11111111 USER1 PASSWORD.…………..…….…..22222222 USER2 PASSWORD.…………..…….…..33333333 USER3 PASSWORD.…………..…….…..44444444 USER4 PASSWORD.…………..…….…..55555555

USER AUTHORITY

REC……………………………….…….….OFF SEARCH&PLAY.……………….……..….OFF

USER’S MANUAL

Page 19

LINK>

SEARCH>

COPY>

OPERATION

COPY……………….………….……..……OFF LIVE AUDIO………………….……………OFF DVR SETUP………………….……………OFF DVR STATUS………………….……….…OFF PTZ CONTROL……………….…………..OFF

DVR MENU SETUP

FACTORY DEFAULT…………..………...NO LOAD MENU FROM FILE SAVE MENU TO FILE

FIRMWARE UPGRADE………………….……….……….NO

NETWORK

DHCP……..………………………………….………OFF IP ADDRESS………………………………………..192 168 000 002 SUBNET MASK……………………………………..255 255 255 000 GATEWAY…………………………………………..192 168 000 001 DNS…………………………………………………..000 000 000 000 PORT……………………………………….………..5400

RS232C

BAUD RATE..………………….…………….……..115200 DATA BIT……..……………………………….…….8 PARITY BIT….……..……………………….………NONE STOP BIT……..…………………………….……….1

RS485

SYSTEM ID……..…………………………….…….1 BAUD RATE..………………….……………….…..115200 DATA BIT……..………………………………….….8 PARITY BIT….……..………………………….……NONE STOP BIT……..……………………………….…….1

PTZ

CH 1~16: MODEL/SPEED/ID….…………………..NONE/9600/1

E-MAIL

SEND E-MAIL………………………………………..OFF

DYNAMIC DNS

DDNS…………………………………………………OFF

CALENDAR SEARCH SEARCH & COPY TIME SEARCH EVENT SEARCH BLOCK SEARCH FILE SEARCH

MEDIA………………………………………...……...USB_FRONT BOOKMARK SEARCH LOG FILE

COPY STATUS

COPY START/ END/ CUR TIME.………….………2000/00/00 00:00:00 MEDIA FORMAT

FORMAT MEDIA..……………………….…………..USB_FRONT

DIGITAL VIDEO RECORDER

Page 20

OPERATION

5.2 BUTTON CONTROLS

5.2.1 POWER ON /OFF

After the connection of power cord and other devices with this DVR, turn the power on. a. The video signal system (NTSC or PAL) is set to NTSC. b. Power Failure Recovery This DVR automatically reverts back to programmed record parameters upon power restoration.

• If there is no video signal at the video signal system is “AUTO”, the video signal system is set to NTSC. Do not input the PAL

type video signal or it may cause the DVR’s malfunction. In this case, turn off and on again.

5.2.2 SCREEN DISPLAY

5.2.2.1 Multi-Display & Full Screen display

a. Multi display

To change a single camera display to the multi camera, press the MULTI button.

b. Full screen display

Press the desired camera number button to display on the monitor.

Use the +10 Button when you select two digit camera numbers. EX) Camera Number 12 = Press the +10 Button, and then press the No. 2 Button.

CAMERA/NUMBER INPUT buttons are used to input the password in the password lock function.

USER’S MANUAL

Page 21

5.2.2.2 Auto Sequence Display

5.2.2.3 Freeze

• Press the AUTO button, each screen display will be automatically switching according to the AUTO SEQUENCE setup.

• If you set up “ADD AUTO SINGLE : OFF” in the AUTO SEQUENCE setup menu, the single display will be skipped.

• To view the single display, set up “ADD AUTO SINGLE : ON” in the AUTO SEQUENCE setup menu and the single display will be included in the auto sequence display.

• Press the AUTO button again to exit the AUTO mode.

If an event takes place, the AUTO SEQUENCE mode will be cancelled. Please refer to the AUTO SEQUENCE of Chapter 6 MENU setup for more information.

OPERATION

MULTI SCREEN MODE

At the Multi display mode, press the FREEZE button and then select the desired camera number. Press the FREEZE button again to release the FREEZE mode.

SINGLE SCREEN MODE

Press the FREEZE button after the desired channel is selected. Press the FREEZE button again to release the FREEZE mode.

- If you press the MULTI button after pressing the FREEZE button, all the channels will display still images.

- FREEZE function is not available, when auto mode is selected. (Refer to AUTO SEQUENCE in the SCREEN menu for further information)

DIGITAL VIDEO RECORDER

Page 22

OPERATION

5.2.3 RECORD

Press the REC button and the following message will be displayed as below;

MANUAL MODE

Press the REC button to begin recording. To stop recording, press the REC button again. The screen will be turned into real time display

mode.

SCHEDULE MODE

When Schedule mode is selected, the recording will be automatically executed according to the recording schedule. (Please refer to the SCHEDULE SETUP in the RECORD setup.)

The color of record indication ( NNNNNNNN ) on the screen will be changed according to the type of recording and refer to the following.

- “ N ” : Manual recording status.

- “ S ” : Schedule recording status.

- “ E ” : Event recording status. (Motion detection/ Video loss/ Sensor)

- “ - ” : Not recording.

All channels will be displayed by “E” even if an event happened just on one channel. “E” will be displayed because this unit enters the event record mode when event happened. If a channel has an event, all channels will be recorded by event recording frame rate to be set in RECORD PROGRAM menu.

USER’S MANUAL

Page 23

OPERATION

5.2.4 SEARCH & PLAYBACK

Press the SEARCH button, the SEARCH menu screen appears.

TIME SEARCH

If you press the PLAY button in the real time screen mode, playback will be executed from the end of the previous time search and press the desired channel select button. To exit the playback mode and see the live screen again, press LV/PB button.

5.2.4.1 CALENDAR SEARCH

At the SEARCH menu;  Move the cursor to CALENDAR SEARCH using or button.  Press the ENTER button and the CALENDAR SEARCH screen appears.

* The date is displayed by white in case of no data.  Move the cursor to the desired position using the , , , buttons.  And then press the ENTER button, and the following screen appears.

 Move the cursor to the desired position using the , buttons and then press the ENTER

button to play the selected time.

Note : Dots in green color on the bar indicates recorded data.

DIGITAL VIDEO RECORDER

Page 24

OPERATION

5.2.4.2 SEARCH & COPY

At the SEARCH menu;  Move the cursor to TIME SEARCH using or button.  Press the ENTER button and TIME SEARCH screen appears.

 Select the desired HDD ID using the (-) or (+) button.  Move the cursor to CHANNEL using the or button and select the desired channel using the

(-) or (+) button.

 Move the cursor to the desired position of SEARCH TIME using the , , , buttons, and

then set up the desired time using the(-), (+) buttons.

 Press the ENTER button and you can playback.  Press ESC button to go to the previous menu. Move the cursor to START COPY and then press the ENTER button .

Enter a PASSWORD if your want to protect your File. If you don’t want a password press

ESC to start to COPY

5.2.4.3 TIME SEARCH

At the SEARCH menu;  Move the cursor to TIME SEARCH using or button.  Press the ENTER button and TIME SEARCH screen appears.

 Select the desired HDD ID using the (-) or (+) button.  Move the cursor to CHANNEL using the or button and select the desired channel using the

(-) or (+) button.

 Move the cursor to the desired position of SEARCH TIME using the , , , buttons, and

then set up the desired time using the(-), (+) buttons to set the search time.

 Press the ENTER button and you can playback.  Press the ESC button to exit this menu.

USER’S MANUAL

Page 25

OPERATION

5.2.4.4 EVENT SEARCH

At the SEARCH menu;  Move the cursor to EVENT SEARCH using or button.  Press the ENTER button and the EVENT SEARCH menu screen appears.

 Select the desired HDD ID using the (-) or (+) button.  Move the cursor to CHANNEL using the or button and select the desired channel using the

(-) or (+) button.

 Move the cursor to EVENT using the or button and select the event type to search using

the (-) or (+) button.

 Move the cursor to the desired position of SEARCH TIME using the , , , buttons,

and then set up the desired time using the(-), (+) buttons.

 Press the ENTER button, and the event list searched appears.  When the event list appears on the screen, select the desired list using , buttons and

press the ENTER button for the playback.

- When video loss is detected, up to five seconds of pre-recording data is stored on the HDD and the details will be listed in the EVENT LIST. The beep sounds and the LED of the ALARM RESET button will flicker. Press the ALARM RESET button to remove this signal.

- When the unit receives a signal from the sensor input, DVR begins to record the input data according

to the PRE/POST TIME in the RECORD setup and the details will be listed in the EVENT LIST.

5.2.4.5 BLOCK SEARCH

At the SEARCH menu;  Move the cursor to BLOCK SEARCH using or button.  Press the ENTER button and the BLOCK SEARCH menu screen appears.

DIGITAL VIDEO RECORDER

Page 26

OPERATION

 Select the desired HDD ID using the (-) or (+) button.  Move the cursor to the desired position of SEARCH TIME using the , , , buttons,

and then set up the desired time using the(-), (+) buttons.  Press the ENTER, and the list searched appears.  When the list appears on the screen, select the desired list using , buttons and press the

ENTER button for the playback.

5.2.4.6 FILE SEARCH This function allows you to PLAYBACK by EVENT LIST any information previously BACKED UP or COPIED from the DVR to any media. (CD, DVD or USB flash drive).

At the SEARCH menu;  Move the cursor to FILE SEARCH using or button.  Press the ENTER button and the FILE SEARCH screen appears.

 Select the desired type of MEDIA using the (-) or (+) button.  Press the ENTER button, and the list searched appears.  When the list appears on the screen, select the desired list using , buttons.  Press the ENTER button for the playback.

5.2.4.7 BOOKMARK SEARCH This function allows you to PLAYBACK events created by the BOOKMARK feature. This is helpful when you make a list of important events while you are on PLAYBACK mode.

At the SEARCH menu;  Move the cursor to BOOKMARK SEARCH using or button.  Press the ENTER button and the BOOKMARK SEARCH screen appears.

 Press the ENTER button, and the list searched appears.

USER’S MANUAL

Page 27

 When the list appears on the screen, select the desired list using , buttons.  Press the ENTER button for the playback.

 Press the “PB/PAUSE” button to playback.  Find the desired image using the SLOW, FAST, DIR buttons.  Press the “PB/PAUSE” button to see the still picture of the desired image.  Press the “PTZ” button to add the BOOKMARK list.

CAUTION

 If the internal HDD(s) is initialized, all of the event images will be deleted.  When the unit is in normal recording status, the pre-recording will not be executed.

5.2.4.8 LOG FILE The LOG FILE SEARCH is not for PLABACK, it is for event information only. This is useful to find important information regarding to important events.

At the SEARCH menu;  Move the cursor to LOG FILE using or button.  Press the ENTER button and the LOG FILE screen appears.

 Move the cursor to the desired position of SEARCH TIME using the , , , buttons,

and then set up the desired time using the(-), (+) buttons.  Press the ENTER button, and the list searched appears.  When the list appears on the screen, select the desired list using , buttons.

OPERATION

DIGITAL VIDEO RECORDER

Page 28

OPERATION

5.2.5 PLAY BUTTON INFORMATION

5.2.5.1 SLOW ( )

Press this button to make the speed level which is slower than normal speed (X1) and displayed it at the upper left side of screen as below;(If you press this button again, the playback speed will be changed in the order of the below seven speed level) i. ½ - 2 times slower than normal playback speed ii. ¼ - 4 times slower than normal playback speed iii. 1/8 - 8 times slower than normal playback speed iv. 1/16 - 16 times slower than normal playback speed v. 1/32 - 32 times slower than normal playback speed vi. 1/64 - 64 times slower than normal playback speed vii. 1/128 - 128 times slower than normal playback speed ** : Backward playback still images after pausing of playback image.

5.2.5.2 PB / PAUSE ( ) ( Z- )

Press this button to begin playback at normal speed (X1). Press this button again to pause the playback.

NOTE If you press the “PB” button to playback, it will playback from the end of played final image.

** ( Z- ) : Zoom out of live view in PTZ mode.

 Press the “AUTO” button to set up the A position(starting position) and “(A- )” will be displayed

on upper right of the screen.

 And then press the “FREEZE” button to set up the B position(ending position) and “(A-B)” will be

displayed on upper right of the screen and played between A to B repeatedly.

Press the “PIP(CLEAR)” button and section repetition playback will cancel.

5.2.5.3 FAST ( ) ( Z+ )

Press this button to make faster the speed level which is higher than normal speed (X1) and displayed at the upper left side of screen as below:

i. 2 - 2 times faster than normal playback speed ii. 4 - 4 times faster than normal playback speed iii. 8 - 8 times faster than normal playback speed iv. 16 - 16 times faster than normal playback speed v. 32 - 32 times faster than normal playback speed vi. 64 - 64 times faster than normal playback speed vii. 128 - 128 times faster than normal playback speed

(However much data may be recorded can be searched in 3 seconds) ** : Forward playback still images after pausing of playback image.

5.2.5.4 DIRECTION ( ) Press this button to change direction to forward ( )or backward ( ) in playback mode.

NOTE

** ( Z+ ) : Zoom in of live view in PTZ mode.

Press DIR button to make a reversed playback from the end of recorded or played images during the real time display mode.

USER’S MANUAL

Page 29

OPERATION

5.2.6 DIGITAL ZOOM

 Press the desired camera number button you wish to display on the monitor.  Press the D-ZOOM button. The indication screen appears on the main screen.

 Press the , , , buttons to select the desired location.

 Press the ESC button to exit this screen.

5.2.7 SCREEN SELECT(LV/PB) _8CH

During the playback, press the LV/PB button to convert the screen into real time display mode. (Press this button again to return to the playback mode.)

DIGITAL VIDEO RECORDER

Page 30

OPERATION

5.2.8 SPOT MONITOR

Set up the desired mode in “SPOT” of “SCREEN MENU” before executing the SPOT mode.

This function allows you to select any LIVE camera to the SPOT monitor while you are on PLAYBACK MODE. This is helpful in cases you need to have an important LIVE camera all the time

5.2.8.1 MANUAL MODE

 Press the “SPOT” button on the front panel to toggle “SPOT” mode indicated on the main

monitor.  Press a camera button to display that camera on the spot monitor.  OSD of the selected channel will be indicated at the upper left of screen in live mode.

5.2.8.2 EVENT MODE The Spot monitor will display the channel which an event happened if you select this mode and an event happens.

NOTE

If you press the “SPOT” button after setting this mode, you can control the spot monitor manually.

5.2.8.3 SEQUENCE MODE Full screen and split screens will be displayed on the Spot monitor in sequence.

NOTE

If you press the “SPOT” button after setting this mode, you can control the spot monitor manually.

** Please refer to 6.2.6 SPOT of SCREEN.

Spot Monitor

USER’S MANUAL

Page 31

OPERATION

5.2.9 COPY

Press the COPY button to copy the recorded images into other media and the COPY MENU screen appears.

5.2.9.1 COPY

5.2.9.1-1 COPY TO EXTERNAL HDD

At the COPY menu, Move the cursor to COPY using the , buttons.

 Press the ENTER button and the following screen appears.

 Select the desired MEDIA using (-), (+) buttons.  Move the cursor to HDD ID using the , buttons and select the desired HDD to copy

among HDD IDs using the (-), (+) buttons.  Move the cursor to the desired position of COPY START TIME/ COPY END TIME using

the , , , buttons and press the (-) or (+) button to set up the time to set up the

COPY START TIME and COPY END TIME.

** Scroll bar - It can operate with just Mouse click.

 Press the ENTER button to copy.

** You can see a password input message. You need this password when opening the file in

network viewer.

NOTE

When the copy is in process, the copying status (ex. “COPY 30%” ) will be displayed on the right side of the monitor.

You can search and playback the copied images in HDD with DVR itself (Please refer to 5.2.4.6 FILE SEARCH.)

** You have to format in case of the media to be used in DVR for the first time.

DIGITAL VIDEO RECORDER

Page 32

OPERATION

5.2.9.1-2 COPY TO USB memory stick

At the COPY menu,

 Move the cursor to COPY using the , buttons.

 Press the ENTER button and the following screen appears.

 Select the desired MEDIA using (-), (+) buttons.

 Move the cursor to HDD ID using the , buttons and select the desired HDD to copy

among HDD IDs using the (-), (+) buttons.

 Move the cursor to the desired position of COPY START TIME/ COPY END TIME using

the , , , buttons and press the (-) or (+) button to set up the time to set up the COPY START TIME and COPY END TIME.

** Scroll bar: - It can operate with just Mouse click.

 Press the ENTER button to copy.

** You can see a password input message. You need this password when opening the file in network viewer.

When the copy is in process, the copying status(ex. “COPY 30%”) will be displayed on the right side of the monitor.

You can search and playback the copied images in USB stick memory with DVR itself as well as PC. (Please refer to 5.2.4.6 FILE SEARCH.)

** You have to format in case of the media to be used in DVR for the first time.

USER’S MANUAL

Page 33

OPERATION

5.2.9.1-3 COPY TO CD-R/ CD-RW/ DVD±RW/ DVD-RAM

At the COPY menu,

 Move the cursor to COPY using the , buttons.

 Press the ENTER button and the following screen appears.

 Select the desired MEDIA(INTERNAL CD-RW/DVD) (-), (+) buttons.

 Move the cursor to HDD ID using the , buttons and select the desired HDD to copy

among HDD IDs using the (-), (+) buttons.

 Move the cursor to the desired position of COPY START TIME/ COPY END TIME using

the , , , buttons and press the (-) or (+) button to set up the time to set up the COPY START TIME and COPY END TIME. ** Scroll bar: - It can operate with just Mouse click.

 Press the ENTER button to copy.

** You can see a password input message. You need this password when opening the file in network viewer.

NOTE

- CD-R, CD-RW or DVD±RW/RAM is option and this DVR need the interface board to install a built-in CDR, CD-RW or DVD±RW/RAM.

- If you want a external CD-RW or DVD±RW, must purchase it from a authorized dealer.

- You can search and playback the copied images in CD or DVD with DVR itself as well as PC.

- The ‘FileViewer’ for the playback of the copied stream is copied to the media also. (Please refer to 5.2.4.6 FILE SEARCH.)

** You have to format in case of the media to be used in DVR for the first time except CD-R.

5.2.9.1-4 STOPPING COPY

Press the COPY button to stop copying and the following screen appears.

DIGITAL VIDEO RECORDER

Page 34

OPERATION

Move the cursor using the , buttons and select “YES” or “NO” and then press the ENTER button.

5.2.10.1-5 CONTINUE COPY

 If the media is full during copying, you can see the following message, “USB MEDIA

FULL OR FAIL PRESS [COPY]” message.

 Press the COPY button and the following screen appears.

 Move the cursor to the CONTINUE COPY and then press the ENTER button.

5.2.9.2 COPY STATUS

At the COPY menu,  Move the cursor to COPY STATUS using the , buttons.  Press the ENTER button to see the current copying status and the following screen appears.

 Press the ESC button to exit this menu.

CUR TIME : Indicate current copying situation among the total copying data.

USER’S MANUAL

Page 35

5.2.10.3 MEDIA FORMAT

At the COPY menu,  Move the cursor to MEDIA FORMAT using the , buttons.  Press the ENTER button and the following screen appears.

 Select formatting media using the (-), (+) button.  Move the cursor to MEDIA FORMAT and then press the “ENTER” button.  The message, “FORMATTING” will be displayed while formatting.

NOTE If you don’t connect any media, you can see the message, “Fail”.

OPERATION

5.2.10 DVR STATUS

Press the “STATUS” button or double-click the left button of Mouse, The SYSTEM INFOMATION screen will appear. To see the next page, press the , or use the wheel scroll of Mouse. Press the STATUS button again to move on next information screen or press the “ESC” button to exit the menu.

DIGITAL VIDEO RECORDER

Page 36

OPERATION

5.2.11 PTZ CONTROL

5.2.11.1 PTZ control in live view

 Press the “PTZ” button to control pan, tilt and zoom functions of PTZ camera and the PTZ

channel, model name and ID will be displayed on the left side of the monitor as the following picture.

 Press the desired camera button to be displayed.

 Use the or button to pan left and right and the or button to tilt up and down.

 Press the PLAY, FAST button to zoom in and out.  Use the (-) or (+) button to focus. Or press the (AF) button for auto focusing. 

Press the PTZ button again to exit the PTZ mode.

** Please refer to 6.6.4 PTZ setup of SCREEN menu.

5.2.11.2 PTZ PRESETTING

 Press the “PTZ” button to enter PTZ mode.  Press the “PRESET” button to enter PRESET mode and “PTZ(PRESET)MOVE”, OSD will

be displayed on the left side of the monitor.

 Move to the desired preset location using the “NUMBER” buttons.  Press the “PRESET” button again and “PTZ(PRESET)SET”, OSD will be displayed on the

left side of the monitor.

 Make the desired setting of the PTZ camera using the , , , , (-), (+) buttons.

 Press the “NUMBER” button to set up the revised presetting.

PRESETS

- A preset is a user-defined camera position using pan and tilt, zoom, and focus commands. This DVR has the Programming capacity for 16 preset locations.

USER’S MANUAL

Page 37

OPERATION

5.2.12 FUNCTION BUTTON

You need this button to control “USER” mode of RELAY 4 SELECT. Please refer to 6.4.8 RELAY OUTPUT.

5.2.13 AUDIO SELECT

< Audio select >

You can select audio channels regardless of monitoring screen. Press the “0(audio select)” button and then press the desired number button and you can hear audio

of selected channel regardless of monitoring screen.

< Link of audio and camera > Press the “0(audio select)” button and then press the “MULTI” button and you can hear audio of

selected camera.

That is to say, you can hear CH 1 audio when viewing CH 1,

CH 2 audio when viewing CH 2, CH 3 audio when viewing CH 3 and CH 4 when viewing CH 4.

Press the “0 (audio select) ” button and then press the “MULTI” button to listen to the audio of the selected camera. With this function if you are using multiple microphones you can listen the desired audio channel with the desired camera while viewing.

5.2.14 PIP CONTROL

 Select a single camera in live view, and then press the PIP button and the following screen will be

displayed.

 Select the desired camera that will be displayed on the PIP screen.  Press the ENTER button to make the bigger PIP screen and use the , , , buttons to

move the position of PIP screen.  Press the ENTER button to change the PIP Box size x2.  Press the ESC button to exit this mode.

DIGITAL VIDEO RECORDER

Page 38

OPERATION

5.3 REMOTE CONTROLLER

○1

○

Button Name Description

○1 REMOTE

CONTROLLER ID

○2 (IRIS-/+) Iris close and open of PTZ ○3 (ZOOM-/+) Zoom in and out of PTZ

○4 SPOT / ESC

○5 ENTER (HOME) Enter / Go home in PTZ mode

○

○6 (  ) / ALARM RESET

○ ○7

○7 ( ▲ ) / MENU

○

○8 ( ▼ ) / PIP

○

○9 (  ) / D-ZOOM

○

○10 AUTO / ( - ) / F(-)

○

○11 FREEZE / ( + ) / F(+)

○

○12 SEARCH / (PRESET)

○

○13 COPY / (AF) Display the copy menu / Auto focus of PTZ

○14 BOOKMARK / (PTZ)

○15 SLOW ( )

○16 PLAY / PAUSE ( )

○17 FAST ( ) Press this button to speed-up playback

○18 LV/PB ( ) Convert the screen into real display mode

○19 DIR ( ) Change the direction of playback ○20 RECORD ( ) Begin and stop recording ○21 MULTI Display multi-screen ○22 TEXT Reserved ○23 AUDIO SELECT Audio select button ○24 CHANNEL ID Camera number select button ○25 FUNCTION Refer to 5.2.12 FUNCTION BUTTON

Refer to 6.5.6 REMOTE CONTROLLER ID in the system setup

Enter the spot mode / Return to the previous mode

Move the cursor in left direction in the setup menu. Frame by Frame(field by field) playback / Release the event signal

Move the cursor up to the next line in the setup menu / Display the setup menu

Move the cursor down to the next line / Enter the PIP mode

Move the cursor in right direction in the setup menu. Frame by Frame(field by field) playback / Control of zoom in and out

Auto sequence / Downward value / Focus control of PTZ

Freeze / Up-going value / Focus control of PTZ

Display the search menu / Enter the preset mode of PTZ

Refer to 5.2.4.7 BOOKMARK SEARCH / Enter the PTZ mode

Press this button to slow-down playback speed

Press this button to begin playback. If press again during the playback, a still picture is displayed

speed

during the playback

5.4 MOUSE CONTROL

○

○1

* You can click the below keys on the MENU screen with a mouse.

○1 Status display Double-click of the left button ○3 Menu display One-click of the right button ○3 Exit Double-click of the right button ○2 Value change Turning the wheel scroll ○1 Select Double-click on the item or icon

USER’S MANUAL

Page 39

MENU SETUP

Chapter 6 MENU setup

ENTRANCE OF THE MENU SETUP

Press the MENU button for the desired DVR setting.

You can use the mouse instead of buttons on the front panel of DVR.

Simply click the desired icon or item in case of using the mouse.

6.1 QUICK SETUP

Press the MENU button and the QUICK SETUP menu appears as the following picture. ** This menu is simply used when user want to change just a few important settings.

Select the desired item using the , buttons and set up the value using the (-), (+) buttons.

6.1.1 QUICK SETUP

Select “ON” or “OFF” using the (-), (+) buttons to use the QUICK SETUP setting.

NOTE : If you select “ON”, RECORD MENU will be disregarded.

6.1.2 IMAGE SIZE

Select the desired IMAGE SIZE ( recording resolution ) for recording using the (-), (+) buttons.

6.1.3 RECORD FRAME

Select the desired frame rate for normal recording using the (-), (+) buttons. All event channels will be recorded by the setting RECORD FRAME/16. For example, if you set RECORD FRAME to 120, 16 each channel will be recorded by 7 ips. ** Please refer to chapter 6.3 RECORD.

6.1.4 EVENT

Select a kind of EVENT using the (-), (+) buttons. If you want to select all kind of event, choose “ALL” and if you don’t want event recording, choose

“OFF”.

The default is “ALL”.

DIGITAL VIDEO RECORDER

Page 40

MENU SETUP

NOTE: Divide event type into three classes(alarm, loss, motion).

6.1.5 PRE RECORD TIME

Select the desired time for pre-recording using the (-), (+) buttons. When video loss, alarm or motion is detected, the DVR will store pre-recorded data during the

selected time. The pre-recording time can be set from 0 second to 5 second and the default is “5”.

6.1.6 POST RECORD TIME

Select the desired time for post-recording using the (-), (+) buttons. When video loss, alarm or motion is detected, the DVR will store post-recorded data during the

selected period. The post-recording time can be set from 0 second to 60 second and the default is “10”.

NOTE: The pre- and post- recording is not valid in normal recording mode.

6.1.7 IMAGE QUALITY

Select the desired image quality using the (-), (+) buttons. There are 3 kinds of image quality. Please refer to chapter 6.3 RECORD.

6.1.8 AUDIO RECORD

Select “ON” or “OFF” using the (-), (+) buttons to record audio.

6.1.9 REMOTE CONTROL ID

Refer to 6.5.6

USER’S MANUAL

Page 41

MENU SETUP

6.2 SCREEN

To set up the SCREEN menu,  Move the cursor to the SCREEN icon using the , buttons in the MENU screen.  Press the ENTER button when the cursor is on the SCREEN icon and the following items appear.

6.2.1 AUTO SEQUENCE

At the SCREEN menu,  Move the cursor to the AUTO SEQUENCE using , buttons.  Press the ENTER button when the cursor is on the AUTO SEQUENCE and the following 4 pages

screen appears.

[ 4CH DVR ] [ 8CH DVR ]

DIGITAL VIDEO RECORDER

Page 42

MENU SETUP

 Move the cursor to each single or split channel using the , buttons.  When the desired channel is selected, change the value of AUTO SEQUENCE duration using

the (-), (+) buttons to set the length of time for switching each channel in sequence.

• The value is from 1SEC to 60SEC and the default is “3SEC”.

 To exit this AUTO SEQUENCE menu, press the ESC button.

VIDEO LOSS SKIP : If selected ON, every VIDEO LOSS channel will be skipped in

ADD AUTO SINGLE: If selected OFF, every single channel will be skipped in

The default is “OFF”.

the AUTO SEQUENCE mode. The default is “ON”.

the AUTO SEQUENCE mode.

[ 16CH DVR ]

USER’S MANUAL

Page 43

MENU SETUP

6.2.2 DISPLAY

At the SCREEN menu,

 Move the cursor to the DISPLAY using , buttons.

 Press the ENTER button when the cursor is on the DISPLAY and the following items

appear.

 To exit this DISPLAY menu, press the ESC button.

6.2.2.1 HDD FREE SPACE

At the DISPLAY menu,  Move the cursor using the , buttons to select the HDD FREE SPACE.  Use the (-), (+) buttons to choose “ON” or “OFF”.

• The default is “ON”.

ON: Remaining capacity of the fixed(not backup) HDDs will be displayed on the screen.

6.2.2.2 HDD FREE SPACE MODE

At the DISPLAY menu,

 Move the cursor using the , buttons to select the HDD FREE SPACE

MODE.

 Use the (-), (+) buttons to choose “PERCENT” or “GIGABYTE”.

• The default is “GIGABYTE”.

PERCENT: Remaining capacity of hard drives will be displayed on the screen in percent.

GIGABYTE: Remaining capacity of the hard drives will be displayed on the screen in gigabyte.

6.2.2.3 RECORD STATUS At the DISPLAY menu,  Move the cursor using the , buttons to select the RECORD STATUS.  Use the (-), (+) buttons to choose “ON” or “OFF”.

• The default is “ON”.

ON: Displaying the recording status of each channel on the screen.

6.2.2.4 CLOCK DISPLAY

At the DISPLAY menu,

ON: The date and time will be displayed on the screen.

 Move the cursor using the , buttons to select the CLOCK DISPLAY.  Use the (-), (+) buttons to choose “ON” or “OFF”.

• The default is “ON”.

DIGITAL VIDEO RECORDER

Page 44

MENU SETUP

6.2.2.5 DATE&TIME MODE

At the DISPLAY menu,  Move the cursor using the , buttons to select the DATE&TIME MODE.  Use the (-), (+) buttons to choose “MM/DD/YY”, “DD/MM/YY” or “YY/MM/DD”.

• The default is “MM/DD/YY”.

YY/MM/DD : All date and time will be displayed in numbers. Ex. 2005/01/01 00:00:00 MM/DD/YY : the month section will be displayed in character. Ex. JAN. 01 2005 00:00:00 DD/MM/YY : the day section will be displayed in character. Ex. 01. JAN 2005 00:00:00

6.2.2.6 TITLE DISPLAY

At the DISPLAY menu,  Move the cursor using the , buttons to select the TITLE DISPLAY.  Use the (-), (+) buttons to choose “ON” or “OFF”.

• The default is “ ON”.

ON: Each channel title will be displayed on the screen. (Please refer to 2-4, TITLE setup)

6.2.2.7 TITLE MODE

At the DISPLAY menu,  Move the cursor using the , buttons to select the TITLE MODE.  Use the (-), (+) buttons to choose “TEXT” or “BITMAP”.

• The default is “ TEXT”.

A bitmap is a type of graphics file on a computer.

6.2.2.8 BORDER COLOR

At the DISPLAY menu,

 Move the cursor using the , buttons to select the BORDER COLOR.  Use the (-), (+) buttons to choose “WHITE” or “BLACK”.

• The default is “WHITE”.

WHITE: The color of the border line will be displayed on the multi-channel screen in white. BLACK: The color of the border line will be displayed on the multi-channel screen in black.

6.2.2.9 REMOTE CONTROL ID

At the DISPLAY menu,

 Move the cursor using the , buttons to select the REMOTE CONTROL ID.  Use the (-), (+) buttons to choose “ON” or “OFF”.

• The default is “OFF”.

ON: The remote controller ID will be displayed on the screen.

USER’S MANUAL

Page 45

MENU SETUP

6.2.3 TITLE

At the SCREEN menu,  Move the cursor to the TITLE using , buttons.  Press the ENTER button when the cursor is on the TITLE and the following 2 pages

screen appears.

 Use the , buttons to see the next page.

 Press the ENTER button after selecting desired channel using the , buttons

and the following screen appears.

 Select the character using the , , , buttons and then press the ENTER button.

 To exit this CHARACTER TABLE screen, press the ESC button.

CHANNEL TITLE MODE: There are “TEXT” and “BITMAP”. TEXT: Using the CHARACTER TABLE BITMAP: It is possible to download new characters using the client software if you want.

DIGITAL VIDEO RECORDER

Page 46

MENU SETUP

6.2.4 MULTI SCREEN

You can select the desired channels and make a 4 split screen and a 9 split screen using this menu. At the SCREEN menu,

 Move the cursor to the MULTI SCREEN using , buttons.

 Press the ENTER button when the cursor is on the MULTI SCREEN and the following screen

appears.

 To exit this MULTI SCREEN menu, press the ESC button.

6.2.4.1 MULTI 4E / MULTI 6 / MULTI 7 / MULTI 9B / MULTI 10 / MULTI 13

 Press the ENTER button after selecting the desired item using the , buttons.

 Set the desired number of camera in each channel screen using the (-), (+) buttons.  Use the , , , buttons to set the other channel screen.  To exit this screen, press the ESC button.

The same camera numbers should not be selected on a multi-screen.

USER’S MANUAL

Page 47

MENU SETUP

6.2.5 COVERT

At the SCREEN menu,

 Move the cursor to the COVERT using the , buttons.

 Press the ENTER button when the cursor is on the COVERT and the following 2 pages screen

appears.  Move the cursor and select the desired item using the , buttons.  Use the (-), (+) buttons to choose “ON” or “OFF”.  Use the , buttons to see the next page.

ON: Selected channel will be displayed in black screen (Hidden camera).

SELECT: It is possible to select among “LIVE&PLAYBACK&NETWORK”, “PLAYBACK&NETWORK”,

“LIVE&NETWORK”, “LIVE&PLAYBACK”, “NETWORK”, “PLAYBACK” and “LIVE”.

COVERT TITLE DISPLAY : If you set “ON” on this item, the “COVERT” word will be displayed

- LIVE: To covert selected channels on live screen

- PLAY: To covert selected channels on playback screen

- NETWORK: To covert selected channels on network viewer screen

on the covert channels. The default is “OFF”.

DIGITAL VIDEO RECORDER

Page 48

MENU SETUP

6.2.6 SPOT

At the SCREEN menu,  Move the cursor to the SPOT using , buttons.

 Press the ENTER button when the cursor is on the SPOT and the following screen

appears.

 To exit this SPOT menu, press the ESC button.

6.2.6.1 SPOT MODE

Use the (-), (+) buttons to select the SPOT MODE.

• MANUAL: Manually select the channel of spot monitor.

• EVENT: Event channel will be displayed automatically on spot monitor.

• SEQUENCE: Every single channel will be switching and displaying in sequence.

6.2.6.2 SPOT SEQUENCE TIME

Use the (-), (+) buttons to set the SPOT SEQUENCE TIME. The duration of spot sequence can be set from 1SEC to 60SEC.

6.2.6.3 VIDEO LOSS SKIP

Select “ON” or “OFF” using the (-), (+) buttons If you select “ON”, loss images will be skipped.

USER’S MANUAL

Page 49

MENU SETUP

6.3 RECORD

To set up the RECORD menu,  Move the cursor to the RECORD icon using the , in the MENU screen.  Press the ENTER button when the cursor is on the RECORD icon and the following items

appear.

6.3.1 RECORD SETUP ( SCHEDULE RECORDING)

This menu allows you to configure a weekly recording schedule. In the schedule you must use the predefined programs ( 0-9 ) in order to set up the recording properly. You can use and combine different predefined programs during the week according with your own needs. ( see RECORD PROGRAM section for more information )

At the RECORD menu,

 Move the cursor to the RECORD SETUP using , buttons.  Press the ENTER button when the cursor is on the RECORD SETUP and the following

screen appears.

 Move the cursor to choose the desired time using the , , , buttons.  Select the desired program among PROGRAM 0~9 and POWER OFF using the (-), (+) buttons

or jog dial.

 Turn right the shuttle ring to set up the schedule of programmed time and the program number

will be green. Turn the left the shuttle ring to release the schedule mode.

Or move the cursor to the desired position and then click the green square next to

“SCHEDULE” using the Mouse.

 Press the ESC button to exit this RECORD SETUP menu or press the ENTER button to enter

the RECORD PROGRAM menu.

DIGITAL VIDEO RECORDER

Page 50

MENU SETUP

6.3.2 RECORD PROGRAM

This feature uses predefined recording modes to create new ones according with your own needs. This means you can create different programs using existing predefined programs. You have available up to 10 different programs ( 0-9). These programs will be used to setup the recording schedule on the RECORD SETUP menu program for Motion detection or another for continuous recoding

At the RECORD menu,

 Move the cursor to the RECORD PROGRAM using , buttons. Press the ENTER button when the cursor is on the RECORD PROGRAM and the following

screen appears

. For example, you can create a

VCE300

RESOLUTION

360 x 240

720 x 240

720 x 480

[4CH DVR]

[16CH DVR]

4CH

FPS/TL

CIF 120

D1/2 60

D1 30

FPS

ch ( Max)

7.5

[8CH DVR]

 Use the , , , buttons to move the cursor to the desired item.

 Select the desired value for each selected

item using the (-), (+) buttons or jog dial.

 After all setting are done, exit using the

‘ESC’ key or the right-double-click of mouse.

When exiting from this menu, the DVR compute the values under this menu. And then if some mistakes exist out of settings it will show the proper error message and return to this menu again. And if ‘0’ IPS value is detected out of setting it will show the warning message for some seconds and exit.

per

8CH

FPS/TL

CIF 120

D1/2 60

D1 30

FPS

per

ch( Max)

7.5

3.75

16CH

FPS/TL

CIF 120

D1/2 60

D1 30

FPS per ch( Max)

1.875

7.5

3.75

USER’S MANUAL

Page 51

Recording IPS Table



1. REC PROGRAM

Shows the current PROGRAM #. Example PROGRAM0. Select the program according with

your needs .Predefine programs are from 0 – 9.

MENU SETUP

• User can choose the program number to be modified here.

2. IMAGE SIZE: Shows the actual resolution of each camera

IMAGE SIZES are : NTSC 360x240, 720x240, 720x480 PAL 360x288, 720x288, 720x576

3. NORMAL RECORD IPS: This setting allows you to configure the # of IPS for continuous recording on each camera. The total IPS will depend on the DVR model and

resolution .The IPS value for each channel can not be over the real-time IPS. The ‘realtime IPS’ is 30 for NTSC and 25 for PAL.

4. EVENT IPS

The EVENT recording mode will record events caused by event conditions. These event conditions can be triggered by different events like, motion detection, external alarm input and video loss detection.

DIGITAL VIDEO RECORDER

Page 52

MENU SETUP

There are two types of events: SINGLE and COMPLEX.

SINGLE

COMPLEX

EVENT CH ONLY ALL CHANNELS

Under the EVENT IPS the DVR will record the channel triggered by any event using the higher IPS on a particular channel.

The rest of the channels of the group will record based on the NORMAL IPS set value on each camera

EVENT CH ONLY ALL CHANNELS

Under the EVENT IPS the DVR will record the channels triggered by any event .

The rest of the channels of the group will record based on the NORMAL IPS set value on each camera

Note: The maximum value between the NORMAL IPS and the EVENT IPS determine the allowed maximum for a channel.

The CH- SUM must not exceed the maximum IPS of the group.

Under the EVENT IPS the DVR will record the channels triggered by any event with the IPS value predefined or set by the user

The rest of the channels of the group will record sharing the remaining NORMAL IPS among all remaining channels.

The DVR records ALL channels triggered by events

Triggered channels use EVENT IPS on each channel.

The rest of the channels of the group will record based on the remaining EVENT IPS among all remaining channels.

EVENT CH-SUM

This item show the currently allocated sum of each channel.

(a) For SINGLE/EVENT CH ONLY

• The displayed format is ‘nn/----’.

• The value ‘nn’ of a channel means the total recording IPS of a group when the event

happens on this channel. The EVENT IPS of this channel and the sum of other channels in a group makes this value ‘nn’.

• Any one of the CH-SUMs can not exceed the maximum IPS of a group because when event

happens with the normal record on the total IPS of a group will be the same value of this.

• ‘----‘ has no meanings.

(b) For SINGLE/ALL CHANNLES

• The displayed format is ‘nn/AUTO’.

• The value ‘nn’ of a channel is the recording IPS of the channel with an event.

and ‘AUTO’ means that the auto-calculated IPS of the channel when event will happen from other channels.

• Under this mode, the ‘GROUP n SUM’ has meaning for only the NORMAL IPS and can not

USER’S MANUAL

Page 53

exceed the maximum IPS of a group. And the total EVENT IPS is always the maximum IPS of a group because the remains of the EVNET IPS for a channel will be allocated to other channels evenly according to the automatic calculated value. So when event(s) happen while the normal record is on, the maximum IPS of a group will be used.

• The displayed format is ‘nn/MAX’.

• The value ‘nn’ of a channel is the greater one between the NORMAL IPS and the EVENT

IPS.

• The actual event recording IPS of a channel is not the ‘nn’ but the value allocated under the

EVENT IPS.

• ‘nn’ can’t exceed the real-time IPS value.

• Because under this mode the NORMAL IPS has meaning even for the event recording

mode, the representative IPS should be the greater one.

• The total sum of all CH-SUM (GROUP n SUM of CH-SUMs) in a group can not exceed the

maximum IPS of a group.

• ‘MAX’ means the greater value of a channel between the NORMAL IPS and the

EVENT IPS. This is only the indication for user’s understanding.

(d) For COMPLEX/ALL CHANNELS

• The displayed format is ‘---/----‘.

• ‘---/----‘, CH-SUM value, has not meaning under this mode at all.

• In this case, only the ‘GROUP n SUM’s of the NORMAL IPS and the EVENT IPS have

the meaningful sum.

5 QUALITY N/E

the recording video quality for a channel. the value under ‘N’ row is for the quality for the normal recording. the value under ‘E’ row is for the quality for the event recording. three step of quality exist. N means the ‘Normal Quality’, H means the ‘High Quality’ and B means the ‘Best Quality’.

6. PRE/POST TIME The unit of the value on this row is the second. PRE TIME is the pre-recording duration that means how long the channel is recorded before the event happen until the moment event issues. POST TIME is the duration that the event channel will be recorded after the moment event issue. PRE TIME can have the value between 0 and 5 seconds. POST TIME can have the value between 0 and 60 seconds.

7. EVENT A/L/M These items are the conditions under which the event recording starts The value ‘0’ means if the ‘0’ checked event condition happen the DVR should start the event recording for this channel and switch to the event recording mode. The value ‘-‘ means to discard this unchecked condition as an event.

MENU SETUP

DIGITAL VIDEO RECORDER

Page 54

(

)

(

MENU SETUP

10 PREDEFINED PROGRAMS ARE INCLUDED BY DEFAULT. PROGRAMS ARE AVAILABLE FROM 0 - 9.

PROGRAM 0. PROGRAM 1

FEATURES.

RECORDING MODES: NORMAL (Continuous) : 1 ips EVENT RESOLUTION . 720 X 240 QUALITY: H/H PRE/POST 5/10 EVENT LOG :0 / 0 / 0. ( ALL Events= ON)

PROGRAM 2. PROGRAM 3

COMPLEX/EVENT CH ONLY 1 ips

FEATURES

RECORDING MODES: NORMAL (Continuous) : 4 fps EVENT RESOLUTION . 360 X 240 CIF QUALITY: N/N PRE/POST 5/10 EVENT LOG : 0 / 0 / 0. ( ALL Events= ON)

SINGLE / EVENT CH ONLY 15 fps

FEATURES.

RECORDING MODES: NORMAL (Continuous) : 3 ips EVENT RESOLUTION . 360 X 240 QUALITY: H/H PRE/POST 5/10 EVENT LOG :0 / 0 / 0.

SINGLE /EVENT CH ONLY 30 ips

ALL Events= ON

FEATURES.

RECORDING MODES: NORMAL (Continuous) : 7 ips EVENT RESOLUTION . 360 X 240 QUALITY: B/B PRE/POST 5/10 EVENT LOG :0 / 0 / 0.

COMPLEX/EVENT CH ONLY 7 ips

ALL Events= ON)

USER’S MANUAL

Page 55

(

)

(

)

(

PROGRAM 4. PROGRAM 5

MENU SETUP

FEATURES.

RECORDING MODES: NORMAL (Continuous) : 2 ips EVENT RESOLUTION . 720 X 240 QUALITY: N/N PRE/POST 5/10 EVENT LOG :0 / 0 / 0.

PROGRAM 6. PROGRAM 7

SINGLE /EVENT CH ONLY 15 ips

ALL Events= ON

FEATURES.

RECORDING MODES: NORMAL (Continuous) : 1 ips EVENT RESOLUTION . 720 X 240 QUALITY: H/H PRE/POST 5/10 EVENT LOG :0 / 0 / 0.

SINGLE /EVENT CH ONLY 30 ips

ALL Events= ON)

FEATURES.

RECORDING MODES: NORMAL (Continuous) : 3 ips EVENT RESOLUTION . 720 X 240 QUALITY: B/B PRE/POST 5/10 EVENT LOG :0 / 0 / 0.

COMPLEX /EVENT CH ONLY 3 ips

ALL Events= ON

DIGITAL VIDEO RECORDER

FEATURES.

RECORDING MODES: NORMAL (Continuous) : 1 ips EVENT RESOLUTION . 720 X 480 QUALITY: N/N PRE/POST 5/10 EVENT LOG :0 / 0 / 0.

SINGLE /EVENT CH ONLY 5 ips

ALL Events= ON)

Page 56

(

)

(

MENU SETUP

PROGRAM 8. PROGRAM 9

FEATURES.

RECORDING MODES: NORMAL (Continuous) : 1 ips EVENT RESOLUTION . 720 X 480 QUALITY: H/H PRE/POST 5/10 EVENT LOG :0 / 0 / 0.

SINGLE /EVENT CH ONLY 10 ips

ALL Events= ON

FEATURES.

RECORDING MODES: NORMAL (Continuous) : 1 ips EVENT RESOLUTION . 720 X 480 QUALITY: B/B PRE/POST 5/10 EVENT LOG :0 / 0 / 0.

COMPLEX /EVENT CH ONLY 1 ips

ALL Events= ON)

Pre-defined PROGRAM table>

• These are 10 kinds of program and you can change the program setting.

• The program 0 is used for the QUICK SETUP as well when QUCIK SETUP is ON.

PROGRAM 0 1 2 3 4 5 6 7 8 9

RECORD RECORD SETTING

IMAGE SIZE NORMAL RECORD ONLY EVENT SINGLE

CH - SUM 1 / MAX 86 / - 102 / - 7 / MAX 45 / - 45 / - 3 / MAX 20 / - 25 / - 1 / MAX

QUALITY NORMAL

QUALITY EVENT H N H B N H B N H B

PRE-ALARM RECORDING POST-ALARM RECORDING

EVENT ON/OFF

COMPLEX SINGLE SINGLE COMPLEX SINGLE SINGLE COMPLEX SINGLE SINGLE COMPLEX

EVENT

ONLY

720x240 360x240 360x240 360x240 720x240 720x240 720x240 720x480 720x480 720x480

1 4 3 7 2 1 3 1 1 1

1 15 30 7 15 30 3 5 10 1

H N H B N H B N H B

5 5 5 5 5 5 5 5 5 5

10 10 10 10 10 10 10 10 10 10

V-LOSS V-LOSS V-LOSS V-LOSS V-LOSS V-LOSS V-LOSS V-LOSS V-LOSS V-LOSS

EVENT

ONLY

EVENT

ONLY

EVENT

ONLY

EVENT

ONLY

EVENT

ONLY

EVENT

ONLY

EVENT

ONLY

EVENT

ONLY

EVENT

ONLY

USER’S MANUAL

Page 57

(

)

MENU SETUP

PROGRAM EXAMPLES.

Based on the most common applications you can use an existing program as a reference ( # 3 ) to create a new configuration based on you own needs. Once you finish your program make sure to add it to the SCHEDULE PROGRAM and SAVE it.

1. CONTINUOS RECORDING

FEATURES.

RECORDING MODES: NORMAL (Continuous) : 15 ips EVENT RESOLUTION . 360 X 240 QUALITY: B/B PRE/POST 5/10 EVENT LOG :0 / 0 / 0.

COMPLEX/EVENT CH ONLY 0 ips

ALL Events= ON

2. EVENT MOTION DETECTION

FEATURES.

RECORDING MODES: NORMAL (Continuous) : 0 ips EVENT RESOLUTION . 360 X 240 QUALITY: B/B PRE/POST 5/10 EVENT LOG :0 / 0 / 0.

COMPLEX/EVENT ALL CH 14 ips

3. CONTINOUS + MOTION DET

FEATURES.

RECORDING MODES: NORMAL (Continuous) : 1 ips EVENT RESOLUTION . 360 X 240 QUALITY: B/B PRE/POST 5/10 EVENT LOG :0 / 0 / 0.

COMPLEX/ALL CH 14 ips

DIGITAL VIDEO RECORDER

Page 58

MENU SETUP

6.3.3 IMAGE QUALITY

At the RECORD menu,

 Move the cursor to the IMAGE QUALITY using , buttons.

 Press the ENTER button when the cursor is on the IMAGE QUALITY and the following screen

appears.

 Select the desired RECORD QUALITY using the (-), (+) buttons.  And you can see the size of each image quality and how long you can record in the installed

HDDs by the image quality.

 To exit this IMAGE QUALITY menu, press the ESC button.

NOTE You have to turn off the “REC” button to use the image quality menu.

RECORD TIME: A period how long you can record in free space of installed HDD(s) by setting of Max. frame rate. TOTAL TIME: A period how long you can record in total installed HDD(s) by setting of Max. frame rate.

** The better the image quality is, the bigger the file size is and the worse the image quality,

the smaller the file size is.

6.3.4 AUDIO RECORD

At the RECORD menu,

 Move the cursor to the AUDIO RECORD using the , buttons.

 Press the ENTER button when the cursor is on the AUDIO RECORD and the following screen

appears.

 Select the audio recording channels using the (-), (+) buttons.  Press the AUDIO SEL button and then press the desired channel button on the front panel after

saving this menu and you can hear the selected channel audio.

NOTE : AUDIO SELECT + CHANNEL during live or playback

USER’S MANUAL

Page 59

MENU SETUP

6.3.5 OVERWRITE

This feature allows you to enable or disable the hard drive overwrite feature. At the RECORD menu,

 Move the cursor to the OVERWRITE using , buttons.

 Press the ENTER button when the cursor is on the OVERWRITE and the following screen

appears.

 Use the (-), (+) buttons to set “ON” or “OFF”.  It is possible to set a point of time to work the DISK FULL WARNING. Move the cursor to ” DISK FULL WARNING” using , buttons and then select the desired

value using (-), (+) buttons. The value is from 5% to 10% and OFF is not.  To exit this OVERWRITE menu, press the ESC button.

ON: The recorded data will be overwritten when it is a point of time to work the “OVERWRITE”.

“DISK FULL WARNING” is the rest capacity of the HDD.

If you set “OVERWRITE” to OFF and “DISK FULL WARNING” to 5%, alarm will work when

the rest capacity of the HDD is 5%.

6.3.6 PLAY MODE

At the RECORD menu,

 Move the cursor to the PLAY MODE using , buttons.

 Select the PLAY MODE using the (-), (+) buttons.

FRAME : It will playback images in frame mode which is useful for recorded images in high frame rate.

This may occur moving artifact with recorded images in low frame rate.

FIELD : It will playback images in field mode. This reduces the resolution, but is suitable

for recorded images in low frame rate.

6.3.7 BACKUP MODE

At the RECORD menu,

 Move the cursor to the “BACKUP MODE” using , buttons.

 Select the “BACKUP MODE” using the (-), (+) buttons.

EVENT : Backup only when the event occurs. MIRROR : Recording the same images in backup HDD. OFF : Not backup.

DIGITAL VIDEO RECORDER

Page 60

MENU SETUP

6.3.8 HOLIDAY

At the RECORD menu,  Move the cursor to the “HOLIDAY” using , buttons.

 Press the “ENTER” button to set up “HOLIDAY” and the HOLIDAY menu screen appears.

 Set up “ON” or “OFF” of HOLIDAY RECORD using the (-), (+) buttons.

 Move the cursor using , buttons and set up the value using the (-), (+) buttons.

 To exit this HOLIDAY menu, press the ESC button.

NOTE: DVR will record like SUNDAY recording program on setting HOLIDAY.

6.4 EVENT

To set up the EVENT menu,  Move the cursor to the EVENT icon using the , in the MENU screen.  Press the ENTER button when the cursor is on the EVENT icon and the following items appear.

USER’S MANUAL

Page 61

MENU SETUP

6.4.1 MOTION DETECTION

At the EVENT menu,  Move the cursor to the MOTION DETECTION using , buttons.  Press the ENTER button when the cursor is on the MOTION DETECTION and the following

screen appears.

6.4.1.1 CHANNEL

At the MOTION DETECTION menu,  Move the cursor to CHANNEL using , buttons.  Select the desired channel using the (-), (+) buttons.

6.4.1.2 SENSITIVITY

At the MOTION DETECTION menu,  Move the cursor to SENSITIVITY using , buttons.  Select the sensitivity level using the (-), (+) buttons.

SENSITIVITY: The higher the number is, the more sensitive. 1(lowest) ~ 5(highest)

6.4.1.3 AREA SETUP

Setup the desired area for motion detection. Transparent area shows the detection area. The green area means no detection area.

At the MOTION DETECTION menu,  Move the cursor to AREA SETUP using , buttons.

 Press the ENTER button to set the motion detection area.  Select the motion detection area using the , , , buttons and then press the ENTER

button to save the area.

 To exit this AREA SETUP, press the ESC button.

Mouse operation: Click the right button of mouse and drag to select the desired cells. AREA SETUP GRID: 16 x 12

6.4.1.4 TEST MOTION

At the MOTION DETECTION menu,  Move the cursor to TEST MOTION using the , buttons.  Press the ENTER button to test the motion detection.

 To exit this TEST MOTION, press the ESC button.

DIGITAL VIDEO RECORDER

Page 62

MENU SETUP

6.4.2 EVENT SCREEN MODE

At the EVENT menu,

 Move the cursor to the EVENT SCREEN MODE using , buttons.

 Select the EVENT SCREEN MODE using the (-), (+) buttons.

UNCHANGED : Keeping the current screen even if the event occurs. FULL SCREEN : Display the full screen of the channel which the event occurs. MULTI SCREEN : Display the multi-screen when the event occurs. FULL RETURN : Display the full screen of the channel which the event occurs and return. MULTI RETURN : Display the multi-screen when the event occurs and return.

6.4.3 EVENT RECORD

At the EVENT menu,

 Move the cursor to the EVENT RECORD using , buttons.

 Select “ON” or “OFF” using the (-), (+) buttons.

6.4.4 EVENT MESSAGE

At the EVENT menu,

 Move the cursor to the EVENT MESSAGE using , buttons.

 Select “ON” or “OFF” using the (-), (+) buttons.

ON: The warning message will be displayed when the event occurs.

6.4.5 EVENT MESSAGE RESET

At the EVENT menu,

 Move the cursor to the EVENT MESSAGE RESET using , buttons.

 Set the time to reset the event message using the (-), (+) buttons.

6.4.6 EVENT BUZZER

At the EVENT menu,

 Move the cursor to the EVENT BUZZER using , buttons.

 Select “ON’ or “OFF” using the (-), (+) buttons to set the event buzzer.

USER’S MANUAL

Page 63

MENU SETUP

6.4.7 SENSOR INPUT

At the EVENT menu,  Move the cursor to the SENSOR INPUT using the , buttons.  Press the ENTER button when the cursor is on the SENSOR INPUT and the following 2 pages

screen appears.

 Select the desired channel using the , buttons.  Select the type of sensor which is connected with DVR using the (-), (+) buttons.  To exit this SENSOR INPUT menu, press the ESC button.

Select the right sensor type according to the type of installed sensor with the unit. NORMAL OPEN : The sensor is open in normal times. NORMAL CLOSE : The sensor is close in normal times. NOT INSTALLED: No sensors are connected to the DVR unit

DIGITAL VIDEO RECORDER

Page 64

MENU SETUP

6.4.8 RELAY OUTPUT

At the EVENT menu,  Move the cursor to the “RELAY OUTPUT” using the , buttons.  Press the ENTER button when the cursor is on the “RELAY OUTPUT” and the following

screen appears.

 Move the cursor using the , , , buttons and set up the value using the (-), (+) buttons.  Press the button to see the next page.  To exit this screen, press the “ESC” button.

NOTE

- It is possible to set the RELAY OUTPUT of each channel in the type of event.

- Relay output is from 1 to 4 and it is possible to set the period of the relay output. <RELAY 4 SELECT>

There are POWER, USER, NOT USED and HDD ERROR.

z POWER: The relay is working when power is off. z USER: User can operate the relay manually.

(You can also use this function through network viewer. Please refer to page 87.)

Press the “FUNCTION” button to operate RELAY 4 manually. NC→NO: And then press the (+) button. NO→NC: And then press the (-) button. Press the “FUNCTION” button again if you want to exit this mode.

USER’S MANUAL

Page 65

MENU SETUP

6.5 SYSTEM

To set up the SYSTEM menu,  Move the cursor to the SYSTEM icon using the , in the MENU screen.  Press the ENTER button when the cursor is on the SYSTEM icon and the following items appear.

6.5.1 HDD

At the SYSTEM menu,

 Move the cursor to the HDD using the , buttons.

 Press the ENTER button when the cursor is on the HDD and the following screen

appears.

 To exit this HDD menu, press the ESC button.

DIGITAL VIDEO RECORDER

Page 66

MENU SETUP

6.5.1.1 HDD CONFIGURATION

At the HDD menu,  Move the cursor to HDD CONFIGURATION using the , buttons.

 Press the ENTER button when the cursor is on the HDD CONFIGURATION and the

following screen appears.

 Use the , , , buttons to move the cursor and use the (-), (+) buttons to change the

value.

HDD MODE

- REC: Normal and Event recording

- BACKUP: Only for backup

6.5.1.2 REC HDD FORMAT

At the HDD menu,  Move the cursor to REC HDD INITIALIZE using the , buttons.

 Press the ENTER button when the cursor is on the REC HDD FORMAT and the following

screen appears.

 If you want to initialize, move the cursor to “YES” and then press the “ENTER” button.

If not, move the cursor to “NO” and then press the “ENTER” button.

 To exit this screen, press the ESC button.  To exit this HDD menu, press the “ESC” button again.

USER’S MANUAL

Page 67

MENU SETUP

6.5.1.3 BACKUP HDD FORMAT

At the HDD menu,  Move the cursor to “BACKUP HDD INITIALIZE” using the , buttons.

 Press the “ENTER” button when the cursor is on the “BACKUP HDD FORMAT” and the

following screen appears.

 If you want to initialize, move the cursor to “YES” and then press the ENTER button.

 To exit this screen, press the ESC button.  To exit this HDD menu, press the “ESC” button again.

If not, move the cursor to “NO” and then press the ENTER button.

6.5.2 CLOCK

At the SYSTEM menu,

 Move the cursor to the CLOCK using the , buttons.

 Press the ENTER button when the cursor is on the CLOCK and the following screen appears.

6.5.2.1 DATE&TIME

At the CLOCK menu,

 Move the cursor to the DATE&TIME using the , buttons.

 Press the ENTER button when the cursor is on the DATE&TIME and the following screen

appears.

 Use the , , , buttons to move the cursor to the desired position of date or time.

 Use the (-), (+) buttons to modify the current date and time.

• DATE: YYYY/MM/DD YEAR/MONTH/DAY

• TIME : HH:MM:SS HOUR:MINUTE:SECOND

 To exit this DATE & TIME screen, press the ESC button.

DIGITAL VIDEO RECORDER

Page 68

MENU SETUP

6.5.2.2 TIME ADJUST

At the CLOCK menu,  Move the cursor to the TIME ADJUST using the , buttons.  Press the ENTER button when the cursor is on the TIME ADJUST and the following screen

appears.

 Select “ON” or “OFF” using the (-), (+) buttons when the cursor is on “INTERNET TIME ADJUST”. If the INTERNET TIME ADJUST is “ON”, the time of DVR will be adjusted to the time offered by the internet server.

 Move the cursor using the , , , buttons and then set the IP address of SELECT TIME SERVER using the (-), (+) buttons.

 Set the correct TIME ZONE standardizing GMT(Greenwich Mean Time).  Move the cursor to the DAYLIGHT SAVING TIME(Summer time) using the , buttons and

then select “ON” or “OFF” using the (-), (+) buttons.

 If the DAYLIGHT SAVING TIME set “ON”, set up the starting date and time and end date and time.

Use the , buttons to move the cursor and use the (-), (+) buttons to change

the value.

 To exit this TIME ADJUST menu, press the ESC button.

6.5.3 VIDEO STANDARD

At the SYSTEM menu,

 Move the cursor to the VIDEO STANDARD using the , buttons.

 Select the desired value using the (-), (+) buttons.

If you select “AUTO”, this DVR can detect NTSC/PAL automatically boot time.

The default is “NTSC”.

6.5.4 LANGUAGE

At the SYSTEM menu,

 Move the cursor to the LANGUAGE using the , buttons.

 Select the desired language using the (-), (+) buttons.

Available languages: ENGLISH, KOREAN, JAPANESE , POLISH, SPANISH, RUSSIAN, CHINESE, TAIWANESE

USER’S MANUAL

Page 69

MENU SETUP

6.5.5 REMOTE CONTROL ID

At the SYSTEM menu,

 Move the cursor to the REMOTE CONTROL ID using the , buttons.

 Set the REMOTE CONTROL ID using the (-), (+) buttons.

If you are operating more than one DVR in the same place and wish to use the remote controller, the remote controller ID setup is required.

Creates the Remote controller ID

Select one of ALL, 11~14, 21~24, 31~34, 41~44, and then press the same number button on the supplied remote controller before the operation.

6.5.6 KEY SOUND

At the SYSTEM menu,

 Move the cursor to the KEY SOUND using the , buttons.

 Set “ON” or “OFF” using the (-), (+) buttons.

ON : The beep sounds when you press any buttons on the front panel. OFF : The beep does not sound.

6.5.7 ADVANCED SETUP

At the SYSTEM menu,  Move the cursor to the ADVANCED SETUP using the , buttons.  Press the ENTER button when the cursor is on the ADVANCED SETUP and the following

screen appears.

 To exit this ADVANCED SETUP menu, press the ESC button

NOTE: In case that the PASSWORD CHECK is on, only ADMIN and MASTER can enter the

ADVANCED SETUP MENU.

DIGITAL VIDEO RECORDER

Page 70

MENU SETUP

6.5.7.1 PASSWORD CHECK

At the ADVANCED SETUP menu,

 Move the cursor to the PASSWORD CHECK using the , buttons.  Select ON or OFF using the (-), (+) buttons. If you select OFF, password menu won’t work.

6.5.7.2 SET PASSWORD

At the ADVANCED SETUP menu,  Move the cursor to the SET PASSWORD using the , buttons.  Press the ENTER button when the cursor is on the SET PASSWORD and the following

screen appears.

 Select the administrator or user1~4 to change the password and then press “ENTER” button and you can see the following screen.

 Insert your desired password in the eight digits marked _ _ _ _ _ _ _ _ beside NEW PASSWORD using the CAMERA/ NUMBER INPUT buttons.

 And then reinsert 8 numbers of the NEW PASSWORD in the eight digits marked _ _ _ _

_ _ _ _ beside RE-TYPE using the CAMERA/ NUMBER INPUT buttons to verify the password.

 To exit this menu, press the ESC button.

NOTE: You can use only 0~9 number buttons to setup the PASSWORD. The d ef ault of A DMIN is 11111111, USER1 i s 22222222, USER2 is 33333333,

USER3 is 44444444, USRE4 is 55555555. If you forget the admin password, please contact the authorized dealer.

CAUTION: Change the password after purchasing for a security.

USER’S MANUAL

Page 71

6.5.7.3 USER AUTHORITY

At the ADVANCED SETUP menu,  Move the cursor to the USER AUTHORITY using the , buttons.  Press the ENTER button when the cursor is on the USER AUTHORITY and the following

screen appears.

 Move the cursor using the , , , buttons and change the value using the (-), (+) buttons.

If you set any items by “ON”, the password will be required when you start to work them. The defaults are “OFF”.

6.5.7.4 DVR MENU SETUP

At the ADVANCED SETUP menu,  Move the cursor to the DVR MENU SETUP using the , buttons.  Press the ENTER button when the cursor is on the DVR MENU SETUP and the following

screen appears.

MENU SETUP

6.5.7.4.1 FACTORY DEFAULT

At the DVR MENU SETUP menu,  Move the cursor to the FACTORY DEFAULT using the , buttons.  Press the ENTER button when the cursor is on the DVR INITIALIZE and the following

screen appears.

 If you want to initialize, move the cursor to “YES” and then press the ENTER button. If not,

move the cursor to “NO” and then press the ENTER button. Use the , buttons to move the cursor.

DIGITAL VIDEO RECORDER

Page 72

MENU SETUP

6.5.7.4.2 LOAD MENU FROM FILE

At the DVR MENU SETUP menu,

 Insert the USB memory stick to download the menu file from the USB memory stick.

Move the cursor to the LOAD MENU FROM FILE using the , buttons and then press the ENTER button.

6.5.7.4.3 SAVE MENU TO FILE

At the DVR MENU SETUP menu,

 Insert the USB memory stick to copy the current DVR menu file to the USB memory stick.

 Move the cursor to the SAVE MENU TO FILE using the , buttons and then press the ENTER button.

NOTE : It is possible to copy and upload the menu setting only with a front USB port.

6.5.8 FIRMWARE UPGRADE

At the SYSTEM menu,  Move the cursor to the FIRMWARE UPGRADE using the , buttons.  Press the ENTER button when the cursor is on the FIRMWARE UPGRADE and the following

screen appears.

 If you want to update firmware using the USB port, move the cursor to “YES” and then press the ENTER button. If not, move the cursor to “NO” and then press the ENTER button.

Use the , buttons to move the cursor.

 To exit this FIRMWARE UPGRADE screen, press the ESC button.

NOTE : It is possible to copy and upload the menu setting only with a front USB port.

USER’S MANUAL

Page 73

MENU SETUP

6.6 LINK

To set up the LINK menu,  Move the cursor to the LINK icon using the , in the MENU screen.  Press the ENTER button when the cursor is on the LINK icon and the following items appear.

6.6.1 NETWORK

At the LINK menu,

 Move the cursor to the NETWORK using the , buttons.

 Press the ENTER button when the cursor is on the NETWORK and the following screen appears.

 To exit this NETWORK menu, press the ESC button.

DIGITAL VIDEO RECORDER

Page 74

MENU SETUP

6.6.1.1 DHCP

At the NETWORK menu,

 Move the cursor to the DHCP using the , buttons.

 Select “OFF” using the (-), (+) buttons.

6.6.1.2 IP ADDRESS

At the NETWORK menu,

 Move the cursor to the IP ADDRESS using the , buttons.

 Select the desired position using the

6.6.1.3 SUBNET MASK

At the NETWORK menu,

 Move the cursor to the SUBNET MASK using the , buttons.  Select the desired position using the

, buttons and set the data value using the (-), (+) buttons.

6.6.1.4 GATEWAY

At the NETWORK menu,

 Move the cursor to the GATEWAY using the , buttons.

 Select the desired position using the

6.6.1.5 DNS

At the NETWORK menu,

 Move the cursor to the DNS using the , buttons.

 Select the desired position using the

6.6.1.6 PORT

At the NETWORK menu,

 Move the cursor to the PORT using the , buttons.

 Select the desired position using the

**Note: Default port is : 5400. Only one port is needed.

AVAILABLE PORTS : 5400, 5410. 5420, 5430, 5440, 5450, 5460.5470, 5480, 5490.

NOTE: Port setting on DVR and client viewer software must be matched.

, buttons and set the data value using the (-), (+) buttons.

USER’S MANUAL

Page 75

MENU SETUP

6.6.1.7 DYNAMIC DNS

At the NETWORK menu,

 Move the cursor to the DHCP using the , buttons.

 Select “ON” using the (-), (+) buttons.

 Move the cursor to the DYNAMIC DNS using the , buttons.

 Input the dynamic DNS using the (-), (+) buttons to change the value and

the , buttons to move the cursor.

NOTE: DHCP is a protocol for assigning dynamic IP addresses to devices on a network. ** You have to connect with Router in case of using a network of PPPOE type because this unit

doesn’t have a PPPOE protocol.

** Please refer to the below image in case of a PPPOE type

DDNS(www.ddns.digimerge.net)

DIGITAL VIDEO RECORDER

Page 76

MENU SETUP

6.6.2 RS232C

At the LINK menu,

 Move the cursor to the RS232C using the , buttons.

 Press the ENTER button when the cursor is on the RS232C and the following screen appears.

 Use the , buttons to choose the item and use the (-), (+) buttons to set the data value.

 To exit this RS232C menu, press the ESC button.

NOTE: The Set of value bring about is SERIAL port at DVR near side.

6.6.3 RS485

At the LINK menu,  Move the cursor to the RS485 using the , buttons.  Press the ENTER button when the cursor is on the RS485 and the following screen appears.  Use the , buttons to choose the item and use the (-), (+) buttons to set the data value.  To exit this RS485 menu, press the ESC button.

NOTE

SYSTEM ID : Unit distinction address at Remote keyboard. BAUD RATE : Data transmission speed per second. DATA BIT : Data transmission bit. PARITY BIT : Data transmission error checking. STOP BIT : Data transmission ending bit

USER’S MANUAL

Page 77

MENU SETUP

6.6.4 PTZ

At the LINK menu,

 Move the cursor to the PTZ using , buttons.

 Press the ENTER button when the cursor is on the PTZ and the following 1 or 2 pages

screen appears.

 Select the desired channel using , buttons.  Use the (-), (+) buttons to select the right model of installed PTZ camera.  Press the button to set up a ID of the PTZ camera.

 Use the (-), (+) buttons to select the desired ID.

 Press the button to see the next page.



To exit this PTZ menu, press the ESC button.

Available PTZ protocols: SPD, SRX-100B, VC-C4R,SD-290, SCC-643, PELCO D, DSC-230, CS-854, DMP23, LPT-A100L , PELCO P, BOSCH , TK-C655/C676, SK-D106, EZ

Baud rates : 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200

6.6.5 E-MAIL

At the LINK menu,

 Move the cursor to the E-MAIL using , buttons.

 Press the ENTER button when the cursor is on the E-MAIL and the following screen

appears.

DIGITAL VIDEO RECORDER

Page 78

MENU SETUP

6.6.5.1 SEND E-MAIL

At the E-MAIL menu,

Move the cursor to the SEND E-MAIL using the , buttons and select “ON” using the (-), (+) buttons to send e-mails when an event happened.

6.6.5.2 SMTP SERVER

At the E-MAIL menu,

 Move the cursor to the SMTP SERVER using the , buttons to input the e-mail sever address to be used by DVR.

 Press the ENTER button and the following screen appears.

 Select the character using the , , , buttons and then press the ENTER button.  To exit this CHARACTER TABLE screen, press the ESC button.

6.6.5.3 DVR E-MAIL ADDR

At the E-MAIL menu,

 Move the cursor to the DVR E-MAIL ADDR using the , buttons to input the e-mail address to receive the e-mail when an event happened.

 Press the ENTER button and the following screen appears.

 Select the character using the , , , buttons and then press the ENTER button.  To exit this CHARACTER TABLE screen, press the ESC button.

USER’S MANUAL

Page 79

6.6.5.4 USER ID

At the E-MAIL menu,

 Move the cursor to the USER ID using the , buttons to input the e-mail account to be used by DVR.

 Press the ENTER button and the following screen appears.

 Select the character using the , , , buttons and then press the ENTER button.  To exit this CHARACTER TABLE screen, press the ESC button.

6.6.5.5 PASSWORD

At the E-MAIL menu,

 Move the cursor to the PASSWORD using the , buttons to input the account password to be used by DVR.

 Press the ENTER button and the following screen appears.

 Select the character using the , , , buttons and then press the ENTER button.  To exit this CHARACTER TABLE screen, press the ESC button.

MENU SETUP

DIGITAL VIDEO RECORDER

Page 80

MENU SETUP

6.6.6 DYNAMIC DNS

At the LINK menu,

 Move the cursor to the DYNAMIC DNS using , buttons.

 Press the ENTER button when the cursor is on the DYNAMIC DNS and the following

screen appears.

6.6.6.1 SERVICE PROVIDER At the DYNAMIC DNS menu,

Move the cursor to the SERVICE PROVIDER using the , buttons and select “ON” using

the (-), (+) buttons to be provided the DDNS service.

6.6.6.2 DOMAIN NAME At the DYNAMIC DNS menu,

 Move the cursor to the DOMAIN NAME using the , buttons to input the domain name to

be used.

 Press the ENTER button and the following screen appears.

 Select the character using the , , , buttons and then press the ENTER button.  To exit this CHARACTER TABLE screen, press the ESC button.

USER’S MANUAL

Page 81

6.6.6.3 USER NAME

At the DYNAMIC DNS menu,

 Move the cursor to the USER NAME using the , buttons to input the user name to be

used.

 Press the ENTER button and the following screen appears.

 Select the character using the , , , buttons and then press the ENTER button.  To exit this CHARACTER TABLE screen, press the ESC button.

6.6.6.4 PASSWORD

At the DYNAMIC DNS menu,

 Move the cursor to the PASSWORD using the , buttons to input the account password

to be used by DVR.

 Press the ENTER button and the following screen appears.

 Select the character using the , , , buttons and then press the ENTER button.  To exit this CHARACTER TABLE screen, press the ESC button.

6.6.6.5 DDNS STATUS

 This menu item shows the operation status for DDNS

 If DDNS works well, ‘OK’ will be displayed

MENU SETUP

DIGITAL VIDEO RECORDER

Page 82

MENU SETUP

6.7 SEARCH

To set up the SEARCH menu,  Move the cursor to the SEARCH icon using the , in the MENU screen.  Press the ENTER button when the cursor is on the SEARCH icon and the following items appear.

** Please, refer to Search & Playback of Chapter 5 Operation.

6.8 COPY

To set up the COPY menu,  Move the cursor to the COPY icon using the , in the MENU screen.  Press the ENTER button when the cursor is on the COPY icon and the following items appear.

** Please, refer to Copy of Chapter 5 Operation.

USER’S MANUAL

Page 83

MENU SETUP

6.9 EXIT

At the MENU screen,  Move the cursor to the EXIT icon using the , buttons.  Press the ENTER button when the cursor is on the EXIT icon and the following items appear.

 Move the cursor to the desired item using the , buttons and press the ENTER button.

- SAVE ONLY : Select this item if you want only to save the changed setup.

- SAVE AND EXIT : Select this item if you want to save the changed setup and exit this

screen.

- EXIT WITHOUT SAVE : Select this item if you want not to save the changed setup before

exiting this screen

DIGITAL VIDEO RECORDER

Page 84

EXTERNAL TERMINAL INFORMATION

Chapter 7

External Terminal Information

7.1 RS-485

These ports are to control the connected PTZ cameras and can be used to connect the external controller.

No DESCRIPTION

1 TA(TX+) RS485:Transmit data

2 TB(TX-) RS485: Receive data

3 GND

7.2 T.ADJ

Time adjust input port is high level at normal and check a signal every 100ms. Time adjust output port is open at normal and a space cling to change During keep up 250ms

NO DESCRIPTION FALLING EDGE

1 TIME REFERENCE INPUT TTL

2 TIME REFERENCE OUTPUT

a minute at GND.

To other T.ADJ Input

USER’S MANUAL

Page 85

EXTERNAL TERMINAL INFORMATION

7.3 RELAY OUT

For controlling alarm output by relay

NO DESCRIPTION NO DESCRIPTION

1 NO(Normal Open) 5 NO(Normal Open)

2 CM(Common)

3 NO(Normal Open) 7 NO(Normal Open)

4 CM(Common)

7.4 ALARM

No DESCRIPTION

1 EXTERNAL ALARM 1 INPUT

2 EXTERNAL ALARM 2 INPUT

3 EXTERNAL ALARM 3 INPUT

4 EXTERNAL ALARM 4 INPUT

5 EXTERNAL ALARM 5 INPUT

6 EXTERNAL ALARM 6 INPUT

7 EXTERNAL ALARM 7 INPUT

8 EXTERNAL ALARM 8 INPUT

G ALARM IN COMMON GND

ALARM

V-LOSS

6 CM(Common)

8 CM(Common)

POWER

USER

NOT USED

HDD ERROR

DIGITAL VIDEO RECORDER

Page 86

EXTERNAL TERMINAL INFORMATION

7.5 VGA

This DVR is compatible with TFT LCD monitor in PAL mode. This DVR supports 1024 x 768 resolution & 70Hz refreshed rate in NTSC/PAL mode.

VGA

No DESCRIPTION

1 RED(Red Video [75ohm, 0.7Vp-p] )

2 GREEN(Green Video [75ohm, 0.7Vp-p] )

3 BLUE(Blue Video [75ohm, 0.7Vp-p] )

4~12 Reserved

13 HSYNC or CSYNC(Horizontal or Composite Sync.)

14 VSYNC(Vertical Sync.)

15 Reserved

7.6 SERIAL

This DVR is compatible with TFT LCD monitor in PAL mode.

No Description No Description

1 DCD Not used 6 DSR Not used

2 RxD Receive data 7 RTS Not used

3 TxD Transmit data 8 CTS Not used

4 DTR +12V output 9 RI Not used

5 GND Signal Ground

SERIAL

USER’S MANUAL

Page 87

EXTERNAL TERMINAL INFORMATION

7.7 Ethernet / USB

For both 10Base-T and 100 Base-TX.

ETHERNET

USB2

USB1

No DESCRIPTION

1 N/C (Not Connected)

2 N/C (Not Connected)

3 RX-(Receive Data-)

4 N/C (Not Connected)

5 N/C (Not Connected)

6 RX+(Receive Data+)

7 TX-(Transmit Data-)

8 TX+(Transmit Data+)

No DESCRIPTION

1 VCC

2 USB DATA -

3 USB DATA +

4 GND

DIGITAL VIDEO RECORDER

Page 88

SPECIFICATIONS

Chapter 8

1. VIDEO

Input Level

Video Standard NTSC(525 lines)/ PAL(625 lines)/ AUTO

Display Speed

Display Resolution

Monitor Output

2. AUDIO

LINE Input Level

Output Level

3. RECORDING

*1 Compression Method MPEG4 (Refer to the below table)

*2 Recording speed Refer to the below table

Quality User Define Low/ Fine/ Superfine

Scheduling Available per hour/ each channel

Mode

Water Marking Available

4. HDD

Capacity

Speed Min. 5400RPM, 7200RPM

DMA 45MHz DMA

Type EIDE compatible

Seek time Faster than 9.0ms avg.

External Bay Interface USB 2.0

5. ALARM

Sensor Input Terminal block 4 ports 8 ports 16ports

Alarm Output 4 Relay out (Programmable), Terminal block

Motion Detection Available per each camera/ Multi-detection level

6. CONNECTORS

Video Input BNC 4 ports 8 ports 16ports

Loop Output BNC 4 ports 8 ports 16ports

Monitor Output

Audio Input Stereo 2 ports: Audio 4 CH (Line only)

Audio Output RCA 1 CH (Line only) : Rear 1 port

USB 2.0

Specifications

NTSC 120fps

PAL 100fps

NTSC 720(H) X 480(V)

PAL 720(H) X 576(V)

Main

Spot

VGA

Internal Storage 1 Removable HDD + 2 HDDs (1TB x 3)

External Storage 40 HDDs (10 HDDs in an external bay x 4)

Main BNC 1 port

Spot BNC 1 port

S-Video BNC 1 port (4 pins mini DIN)

VGA(Option) BNC 1 port (15 pins female DSUB)

1.0 Vp-p±10% Composite, 75Ω Balanced

1.0Vp-p Composite, 75Ω Balanced (YC Output)

1.0Vp-p Composite, 75Ω Balanced Analogue non-interlaced RGB.

TFT LCD monitor that support 50Hz VGA mode in PAL

0.5~1.4Vp-p@20kΩ

-10dB 1KΩ

Manual / Event (Motion detection, Video loss, Sensor)/ Schedule

VCE304 VCE308 VCE316

HDD extension/ Mouse/ USB memory stick/ CD-RW/ DVD±RW (Front 1 port, Rear 2 ports)

This DVR is compatible with

USER’S MANUAL

Page 89

SPECIFICATIONS

Serial

Terminal Block External control (RS-485)

Alarm Input 4CH 8CH 16CH

Alarm Output

Ethernet RJ45 connector, 10/100 Mbps

7. ELECTRICAL

Power Source AC (AC85V-235V) to DC(+12V/5A)Adaptor

Power Consumption App. 45W(Including 1 HDD)

8. ENVIRONMENTAL

Operating Temperature

Storage Temperature

Humidity 30 ~ 90%RH (non-condensing)

9. PHYSICAL

Construction Steel case

Color Black

Dimension 420(W) x 68(H) x 330(D) mm

Weight App. 4kg (Including 1 HDD)

10. BACKUP & COPY

Digital Backup Event Backup/ Mirroring

Copy External HDD/ CD-RW/ DVD±RW/ USB Stick (2.0)

11. SEARCHING & PLAYBACK

Searching Method Time/ Event/ File/ Bookmark/POS/ Log file

12. MULTI-REMOTE SURVEILLANCE

Monitoring Environment Client software/ Central monitoring system/ Web

Max. connection DVR 16 DVRs accessible

Max. client Supporting multi-client (5 clients accessible)

13. SYSTEM MONITORING & RECOVERY

Monitoring Software Watchdog

Recovery Auto-Reboot by Watchdog/ Automatic database recovery

14. Others

OS Embedded Linux

Duplexer or Triplexer Triplexer

Control Device

File compatibility with PC (Windows) Compatible

Number of event list/ Log file list 20,000/ 20,000

External control (RS-232C) / For debugging : 9 pins male DSUB

4 Relay output : 3 pins terminal block (Normal-Open, Normal-Close, Common) x 4

0 ~ + 40

-10 ~ + 60

Front key/ Remote controller/ Mouse/ Network viewer Remote keyboard

DIGITAL VIDEO RECORDER

Page 90

SPECIFICATIONS

< Recording Speed Table >

*Note 1, 2 Unit : ips

Model 4CH/ 8CH /16CH Recording Speed

Compression Method MPEG4

NTSC

PAL

RECORDING CONDITIONS (NTSC) Based on 120GB of storage with the installation of 1 camera. This DVR can support up to 23TB with external HDD storage devices. The following table was calculated by a still image.

RECORDING TIME TABLE

MODEL

RECORD

IMAGE

Color Bar

(Simple

image)

Mid-

class

DVR

Cross Hatch

(Complex

image)

• The figures in the Recording Time Table were estimated under ideal recording conditions

and may vary from your actual recording situation.

• In the Recording Time Table, multiply by 2 for recording hours with an 240 GB HDD and

3 for recording hours with a 360 GB HDD.

• The complexity of the image and the amount of motion recorded greatly influences the

recording capacity of your hard drive (HDD). The higher the frames per second and the higher the video quality setting, the lower your HDD recording capacity will be. In the same manner, the lower the frames per second setting and the lower the video quality setting, the higher your HDD recording capacity will be.

• Note that the lower frame rate does not mean a lower video quality. The image quality

remains the same whether the frames per second setting is set high or low. One frame per second is the same as taking a photo every second.

• There are several factors that influence the recording capacity of your hard drive.

(a) The number of cameras used (b) The complexity of recording image © The number of frame recorded per second (d) The image quality setting – Best, High or Normal

360 x 240 120 720 x 240 60 720 x 480 30 360 x 288 100 720 x 288 50 720 x 576 25

IMAGE QUALITY

BEST

HIGH

NORMAL

BEST

HIGH

NORMAL

IMAGE

SIZE

2208 Bytes 1792 Bytes 1288 Bytes 8680 Bytes 5640 Bytes 3696 Bytes

120ips(360x240) 60ips(720x240) 30ips(720x480)

125 Hours 250 Hours

153 Hours 306 Hours

224 Hours 448 Hours

34 Hours 68 Hours

50 Hours 100 Hours

72 Hours 144 Hours

60ips(360x240)

30ips(720x240) 15ips(720x480)

USER’S MANUAL

Page 91

256 CAMERA INTEGRATION SYSTEM

Chapter 9

Block Diagram

256 Camera Integration system

DIGITAL VIDEO RECORDER

Page 92

SPECIFICATIONS

Chapter 10

HDD Installation Process

10.1 Internal HDD installation

10.1.1 How to install the internal Hard Disk Drive(s).

1) Unscrew on the top, the side and the rear

of this unit as indicated to remove the cover.

Caution) Plug out the power cord before addition / removal / change of HDD

2) Remove the upper cover from the unit and unscrew to remove the rack mounts as indicated.

3) Fix the additional HDD to rack mount with the screws as indicated.

USER’S MANUAL

Page 93

HDD INSTALLATION PROCESS

4) Place the HDD(s) on the HDD plate and screw as indicated. Put the ring guides same as picture on the rubber before screwing. (Set the master or slave of HDD before fixing the HDD(s) into DVR. Refer to the HDD Jumper Setting Information.)

* All HDDs must be set by slave or master

5) Connect the power and the flat cables as indicated.

6) Close the top cover and screw.

DIGITAL VIDEO RECORDER

Page 94

SPECIFICATIONS

10.1.2 How to install Hard Disk Drive(s) into the removable HDD rack.

1) Grip the strap of removable HDD rack and pull it out.

2) Remove the cover of removable HDD rack and connect the HDD with the cables as indicated.

3) Put the HDD into the rack and close the top cover.

4) Fix the removable HDD rack into the unit and lock using the supplied key.

USER’S MANUAL

Page 95

HDD INSTALLATION PROCESS

10.2 DVD±RW(or CD-RW) installation

1) Put out the cables and unscrew to

remove the removable HDD rack as indicated.

Note :If you want to install DVD±RW (or CD-RW)

into this DVR, you need a USB to IDE interface board.

2) Remove the removable HDD rack from DVR set as the picture.

3) Unscrew to remove the HDD rack mount

as indicated.

4) Screw to fix the rack mount on DVD±RW

(or CD-RW) as indicated.

5) Put the DVD±RW(or CD-RW) into the

unit as indicated.

DIGITAL VIDEO RECORDER

Page 96

SPECIFICATIONS

6)Screw to fix the DVD±RW(or CD-RW) as

indicated.

7) Prepare for the USB to IDE interface

board and parts to connect it as the picture.

8) Connect the USB to IDE interface board

and cable as the picture and then close the upper cover of the unit.

HDD Jumper Setting Information

Before install the Hard Disk Drive(s), please read the jumper setting information on the label. If the jumper is not set properly, the system will be disordered. Jumper setting is different according to HDD model.

Please visit following web sites of Hard Disk Drive manufacturer for more information about jumper setting.

HITACHI : www.hitachi.com MAXTOR : www.maxtor.com SAMSUNG : www.samsunghdd.com SEAGATE : www.seagate.com WESTERN DIGITAL : www.westerndigital.com

USER’S MANUAL

Page 97

DYNAMIC DDNS SERVER SETUP

Chapter 11

Network Viewer (DIGI-Client 4.0)

11.1 Installation of Network Viewer Software

11.1.1 System requirement

• Pentium III or above recommended

• O/S : Microsoft Windows 2000 / XP

• 128MB RAM or above recommended

• Super VGA 16M or above recommended

• 10/100 base T network card for LAN operation

11. 1.2 N etwork Environment

Minimum More than 1Mbps More than 0.5Mbps

Recommended

(16 Frames/Sec)

∗ Transfer rate of image varies with the number of client accessed to DVR.

NOTE : The software, DIGI-Client is compatible with Microsoft Windows 2000 / XP.

11.1.3 Installation

To start the installation,

Start Windows 2000 or XP

○

Insert Network Client Software

CD into the CD-ROM drive.

Install Network Client Software and locate

○

○4 Simply double-click the icon to start.

○

Input your desired password and

○

And the main menu controller of network viewer

11.2 Connecting to DVR

Please double-click the icon of Network viewer, and then the following main menu controller will appear on the PC screen.

network viewer file on your PC screen.

press the enter key.

will appear on the screen.

Client PC DVR

More than 3Mbps More than 3Mbps

DIGITAL VIDEO RECORDER

Page 98

11.2.1 Add a new site information

 Click the “Select a DVR” button to display the DVR List on the screen.  Fill out Type, DVR Name, IP address and Password to add the desired units into the DVR

information box, and then click on the “Add” button to save the information.

11.2.2 Change the site information  In case of any changes, type new information into the box after selecting the desired DVR on the list.  Click the “Change” button to save the changes.

11.2.3 Delete the site information

 Select the desired DVR on the list, and then click the “Delete” button to erase the information on

the list.

11.2.4 Connect to a DVR.

 Select the desired DVR that you want to connect in the “DVR list”.  Select the necessary Information according to the connection type.  Click the “Connect” button or to access the DVR and the images screen will be displayed.

NOTE

You can connect 16 x 16(16 users x 16 units) windows at the same time but Master viewer is only one by user.

PASSWORD

- T he d ef au lt p as sword of adm in istra to r is 11111111.

- To change the password, please refer to the PASSWOR D setup in Chapter 6 Set up MENU.

- The password must be the same as the registered site password.

11.2.5 Viewer Screen

 Click the button to see the full view window with control bar.

 RECORD Status

 LIVE

 Playback

USER’S MANUAL

Page 99

ply

DYNAMIC DDNS SERVER SETUP

11.3 DVR search

: This menu allows you to detect all the units on the local network.

 Click “Search DVR” button to display the “Search” menu window.  Click the “Search” button, and then all the units on the local network will be detected and listed on

the screen.

 Click the desired unit, and then click the “Add to list” button to add the unit into the “DVR list”.

11.4 HDD search

Connect DVR’s HDD with local PC, and then please double-click the Network viewer icon and the main menu controller will appear on the PC screen.

 Click the “HDD search” button and the view screen of HDD detected will appear on the PC

screen.

 Click the desired one of the “SEARCH” buttons and SEARCH window will appear on the PC

screen.

 Click the Play button after select of the desired Channel and Search Time in Time Search

window.

 Click the Search button after select of the desired Channel, Event type and Search Time in

Event Search window and then click the Play button after select of the desired list.

If you want to see the next list, click the Next button before playing.

 Click the Search button after input of the desired Search Time in Block Search window and

then click the Play button after select of the desired list.

If you want to see the next list, click the Next button before playing.

NOTE

- You can directly install the removable HDD rack from DVR to PC if compatible rack guide is installed on the PC. In this case, please check the jumper setting for proper operation.

- You can also sim

use external IEEE1394 HDD reader.

DIGITAL VIDEO RECORDER

Page 100

11.5 File Search

At the above main menu controller, 

Click the “File Search” button and the “File list” window will appear on the PC screen.

 If you want to search images saved in CD-RW, DVD±RW or PC, insert the CD or DVD

into your PC and click the “File Search” button and the File Search window will appear.

 Click the “Folder Select” button and then select the desired folder and then click the “OK”

button.

 Select the desired list and then click the “Play” button.

 Click the “File Search” button and the “File list” window will appear on the PC screen.

 Select the file to convert to AVI file and then click the “AVI Convert” button.  Select the folder to save the converted AVI file.  You can see the “Success” message when the converting is finished.

NOTE

- You need DivX codec to play the converted AVI files using Windows media.

We don’t supply the DivX codec so you must download the DivX codec by yourself.

100

USER’S MANUAL