Page 1
Instruction Manual
M3200 / M4200 SERIES
Page 2
Page 3
Instruction Manual
M3200 / M4200 SERIES
#LX400051; r. 1.0/23100/23101; en-US
iii
Page 4
Thank you for purchasing this product. FLIR is committed to providing our customers with a high quality,
reliable security solution.
This manual refers to the following models:
M3200 Series: M3204 (4-channel) / M3208 (8-channel) / M3216 (16-channel)
M4200 Series: M4204 (4–channel) / M4208 (8–channel)
For the latest online manual, downloads and product updates, and to learn about our complete line of
accessory products, please visit our website at:
www.flirsecurity.com/pro
WARNING
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING: TO REDUCE THE RICK OF ELECTRIC SHOCK DO NOT REMOVE
COVER. NO USER SERVICABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral
triangle, is intended to alert the user to the presence of uninsulated
"dangerous voltage" within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of electric shock.
The exclamation point within an equilateral triangle is intended to
alert the user to the presence of important operating and
maintenance (servicing) instructions in the literature accompanying
the appliance.
WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS UNIT
TO RAIN OR MOISTURE.
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF THE PLUG
TO THE WIDE SLOT AND FULLY INSERT.
#LX400051; r. 1.0/23100/23101; en-US
iv
Page 5
Table of contents
1 Important Safeguards ................ ........... ........... ........... ........... ........... ... 1
1.1 General Precautions ......... ........... ........... ......... .. ......... .. ......... .. ....1
1.2 Installation....... .................... ........... ........... ........... ........... .......... 1
1.3 Service .. ......... .. ........... ......... ........... ........... ........... ......... .. ........ 3
1.4 Use.... ........... ........... ......... ........... ........... ........... ........... ........... 3
2 M3200 Series Features ....... ........... ........... ......... .. ......... .. ........... ...........4
3 M4200 Series Features ....... ........... ........... ......... .. ......... .. ........... ...........5
4 Getting Started (M3200 / M4200 SERIES). ........... ......... ........... ........... ..... 6
5 Series Front Panel (M3200 / M4200 SERIES) ... ........... ........... ........... ....... 7
5.1 M3200 / M4200 Series...... ........... ........... ......... .. ......... .. ......... .. ....7
6 Rear Panel (M3200 / M4200 SERIES) . .. ......... .. ......... .. ......... ........... ......... 9
6.1 M3200 Series ........ ........... ......... ........... ........... ........... ......... .. ....9
6.2 M4200 Series ........ ........... ......... ........... ........... ........... ......... .. .. 10
7 Basic Setup (M3200 / M4200 SERIES) .................. ........... ........... ......... . 12
7.1 Step 1: Connect the BNC Cameras...... ........... ........... .. ......... ........ 12
7.2 Step 2: Connect the Mouse.. ........... ........... ........... ........... ........... 12
7.3 Step 3: Connect the Ethernet Cable ........... ........... ........... ......... .. .. 12
7.4 Step 4: Connect the Monitor.. ........... ........... .................... .. ......... . 13
7.5 Step 5: Connect the Power Adapter and Power on the DVR.... .. ......... . 13
7.6 Step 6: Upgrade Firmware to Latest Version (if Available) ..... ........... .. 13
7.7 Step 7: Verify Camera Image........ .. ........... .................... ........... ... 14
7.8 Step 8: Set the Time ..... ........... ........... ........... ......... .. ......... .. ...... 14
7.9 Default System Password & Port Numbers .. ........... ........... ........... .. 14
7.9.1 FLIR Cloud™ . ......... .. .................... ........... ........... .......... 14
7.10 Quick Access to System Information .... ........... ........... .. ......... ........ 15
8 About MPX... ........... ........... ......... .. ........... ........... ........... ......... .......... 16
8.1 What types of cabling and run lengths does MPX work with?...... .. ...... 16
9 Mouse Control ........ ........... ......... .. ........... ........... ......... ........... .......... 17
10 Remote Control . ......... ........... ........... ........... ......... .. ........... ........... ..... 18
10.1 Setting the Remote Control Address ..... .. ......... .. .................... ....... 19
11 Using the System ........ ........... ........... ........... ........... ........... ........... .... 20
11.1 On-Screen Display ....... ........... ........... .................... .. ......... .. ...... 20
11.2 Using the Quick Menu.. .. ......... ........... ........... ........... .................. 21
11.3 Adjusting Color Settings ..... ........... ........... ........... ........... ......... ... 21
11.4 Using the Navigation Bar ......... .................... ........... ........... ......... 22
11.5 Using the Camera Toolbar ....... .. ......... ........... ........... ........... ....... 22
11.5.1 Using Quick Playback ........... ........... ........... ........... ......... 23
11.5.2 Using Digital Zoom in Live Display .......... ........... ........... ..... 23
11.5.3 Using Real-time Backup .. .................... ........... ........... ...... 23
11.6 Using the Virtual Keyboard........ .................... ........... .. ......... .. ...... 24
12 Setting The Time .......... ........... ........... ........... ......... ........... ........... ..... 25
13 Recording.. .. ......... .. ......... ........... ........... ........... ......... ........... .. ......... . 26
13.1 Video Recording Types ............ ......... ........... ........... .. ......... ........ 26
13.2 Main Stream and Sub Stream.. ........... ........... ........... ......... .......... 26
13.3 Setting up Scheduled or Manual Recording ....... .. ........... ................ 26
13.4 Configuring Hard Drive Overwrite ... ......... .. ......... .. ......... .. ......... .... 27
14 Search (Playback) ... ......... .. ......... .. ........... ........... ......... ........... .......... 28
14.1 Playing Back Video from the Hard Drive...... ......... .. ......... .. ......... .. .. 28
#LX400051; r. 1.0/23100/23101; en-US
v
Page 6
Table of contents
14.2 Playback Controls ................ ........... ........... ........... ........... ......... 29
14.3 Playing Back from a USB Drive ...... ........... ......... .. ......... .. ......... .. .. 29
15 Backup........... ......... ........... .. ......... .. ......... ........... ........... ........... ....... 31
15.1 Formatting the USB Thumb Drive ........ ........... .................... .......... 31
15.2 Backing up Video.......... ........... ......... .. ......... .. ........... ................ 32
15.3 Using Video Clip Backup ..... ......... ........... ........... ........... ......... .. .. 32
15.4 Viewing Backup Files...... ......... ........... ........... ........... ......... .. ...... 33
15.4.1 Viewing Backup Files on PC .... ........... ......... ........... .......... 33
15.4.2 Viewing Backup Files on Mac ........ ........... ......... .. ......... .. .. 36
16 Managing Passwords and User Accounts....... ........... ........... ........... ..... 39
16.1 Changing Passwords...... ........... ........... ........... ........... ......... ...... 39
16.2 Adding Users . ........... ........... ........... ........... ........... ................... 40
16.3 Modifying Users ................... ........... ........... ........... ........... ........ 40
16.4 Deleting Users ... ........... ........... .................... ........... ........... ...... 41
16.5 Account Groups ........ ........... ........... ........... ........... ........... ........ 41
16.6 Adding Groups ... ........... ........... ........... .................... ........... ...... 41
16.7 Modifying Groups .......... ........... ........... ........... ........... ............... 42
16.8 Deleting Groups ..... .................... ........... ........... ......... .. ......... .. .. 42
17 Using the Main Menu ..... ........... ......... ........... .. ......... .. ......... ........... .... 43
17.1 Camera ......... ......... ........... ........... ........... ......... .. ........... ......... 43
17.1.1 Recording... ........... .................... ........... ........... ........... .. 43
17.1.2 Configuring Recording Quality ......... .................... ........... .. 44
17.1.3 Configuring Audio Recording ....... .................... ........... ...... 45
17.1.4 Configuring Snapshot Recording Settings.. .................... ...... 45
17.1.5 Creating Custom Channel Names.... ........... ........... .. ......... . 46
17.1.6 Selecting Cable Type ... ........... ........... .................... ......... 47
17.2 Info ......... ........... ........... ........... ......... .. ......... .. ......... .. ......... .... 48
17.2.1 HDD Info .................. ........... ........... ........... ........... ........ 48
17.2.2 Record Info... ........... ........... ......... .. ......... .. ........... ......... 48
17.2.3 Version ... .. ......... .. ......... .. .................... ........... ........... ... 49
17.2.4 Alarm Status .... .................... ........... ........... .. ......... ........ 49
17.2.5 Online Users ..... ........... ........... ........... ........... ........... ..... 50
17.2.6 Load......... ........... ........... ........... ........... ........... ............ 50
17.2.7 Test........... ........... .................... ........... ........... ........... .. 51
17.2.8 BPS .......... ........... ........... ........... ........... .................... .. 51
17.2.9 Log ..... .................... ........... ........... ........... ........... ........ 51
17.3 Setting.... .................... ........... ........... ......... .. ........... ........... ..... 53
17.3.1 Network .............. ........... ........... ........... ......... .. ......... .. .. 53
17.3.2 Selecting DHCP or Static IP Address (TCP/IP) .......... .. ......... . 53
17.3.3 Configuring System Ports (Connection)......... ......... ........... .. 54
17.3.4 Configuring DDNS Settings . .................... ........... ........... ... 54
17.3.5 Configuring Email Alerts ... .. .................... ........... ........... ... 55
17.3.6 Event...... ......... ........... ........... ........... ........... ........... ..... 56
17.3.7 Configuring Motion Detection......... ......... .. ......... .. ......... .... 56
17.3.8 Configuring Video Loss Settings ........... ......... ........... ......... 58
17.3.9 Configuring Alarm Input Devices..... ......... .. ......... .. ......... .. .. 59
17.3.10 Controlling Alarm Output Devices .... ........... ......... ........... ... 60
17.3.11 Configuring Hard Drive Warnings.... ........... ........... ......... .. .. 61
17.3.12 Configuring Network Warnings . ........... ........... ................... 62
17.3.13 Storage.......... ........... .................... ........... ........... ......... 62
#LX400051; r. 1.0/23100/23101; en-US
vi
Page 7
Table of contents
17.3.14 Configuring the Video Recording Schedule ....... ........... ........ 63
17.3.15 Configuring Pre-Recording . ........... ........... ......... .. ......... .. .. 63
17.3.16 Configuring the Snapshot Schedule ..... ........... ........... ........ 64
17.3.17 Configuring Holidays........ ........... ........... ........... .............. 65
17.3.18 Formatting the Hard Drive . ........... .................... ........... ..... 66
17.3.19 Configuring Hard Drive Type................. ........... ........... ...... 67
17.3.20 Setting up Hard Drive Mirroring (Advanced) ... .. ........... ......... 67
17.3.21 Configuring General System Settings ......... ........... ......... .. .. 68
17.3.22 Setting the Monitor Resolution (Display) ........... .. ......... .. ...... 69
17.3.23 Configuring RS232 for a PTZ Keyboard........ ........... ............ 70
17.3.24 Saving Your System Configuration to a USB Thumb
Drive ................ ........... ........... .. ......... ........... ........... .... 71
17.3.25 Setting the System to Factory Defaults...... ......... ........... ...... 72
17.3.26 Upgrading Firmware from USB.. .. ......... .. ........... ......... ....... 73
17.4 Shutdown.... .. ......... .. ......... ........... ........... ........... ......... .. ......... . 75
18 Connecting to Your System Over the Internet on PC or Mac ....... ........... .. 76
18.1 System Requirements..... .................... ........... ........... ........... ...... 76
18.2 Step 1 of 3: Connect your System to Your Router ............... ........... ... 76
18.3 Step 2 of 3: Obtain the system’s Device ID..... .. ......... ........... ........... 77
18.4 Step 3 of 3: Connect to the System Over the Internet ....... ......... .. ...... 77
19 Using FLIR Cloud™ Client for PC or Mac .. ........... ......... ........... ........... .. 81
19.1 Home Page ..... .. ........... .................... ........... ........... ......... .. ...... 81
19.2 Live View ....... ......... ........... ........... ........... ......... .. ........... ......... 81
19.2.1 Live View Controls.. ........... ........... ........... ........... ........... . 82
19.2.2 Opening Live View in Multiple Monitors ....... ......... .. ......... .. .. 83
19.3 Controlling PTZ Cameras .... ........... .. ......... .. ......... ........... ........... 84
19.3.1 PTZ Presets... ........... ........... ........... ........... ........... ........ 85
19.3.2 PTZ Tours.... .................... ........... ........... ........... ........... . 86
19.3.3 PTZ Pattern ........... ........... ........... .................... ........... .. 87
19.3.4 PTZ Scan ....... .. ......... .. ......... .. ......... ........... ........... ....... 88
19.3.5 PTZ Pan...... ......... ........... ........... ........... ........... ........... . 88
19.4 Playback. ........... ......... ........... ........... ........... ........... ........... ..... 88
19.5 Playback Controls ................ ........... ........... ........... ........... ......... 90
19.6 Downloading Video to your Computer Hard Drive... .................... ...... 91
19.7 Alarm .......... ........... .................... .. ......... .. ......... .. ......... ........... 92
19.8 Log.... ........... ........... ........... ........... ........... ......... ........... ......... 93
19.9 E-map .......... ........... ........... ........... ........... ........... ......... .......... 94
19.10 Devices .. ........... ........... ........... ........... .................... ........... ..... 96
19.11 Device Config ......... ........... ......... ........... ........... ........... ........... . 97
19.12 Alarm CFG .. .. ......... .. ......... ........... ........... ........... ........... ......... . 97
19.13 Tour & Task ..... .. ........... ........... .................... ........... ........... .... 100
19.14 Account ..... ........... ........... ........... ........... ........... .................... 101
19.14.1 Managing User Accounts..... ........... ......... ........... ........... 101
19.14.2 Managing Roles........ ........... ......... .. ......... .. ........... ....... 103
19.15 General ....... .................... ........... .. ......... .. ......... ........... ......... 104
19.15.1 Basic.. ........... .. ......... ........... ........... ........... ......... ....... 104
19.15.2 File ..... .................... ........... ........... ........... ........... ...... 104
19.15.3 Alarm Prompt ........... ........... ........... ......... .. ........... ....... 105
19.15.4 Version .......... ........... ........... ......... ........... ........... ....... 106
20 Connecting to your System Using Smartphone or Tablet Apps. ........... .. 107
20.1 iPhone........... ......... ........... ........... ........... ......... .. ........... ....... 107
#LX400051; r. 1.0/23100/23101; en-US
vii
Page 8
Table of contents
20.1.1 Prerequisites....... ........... ........... ........... .................... ... 107
20.1.2 Connecting to your System on iPhone............ ........... ........ 107
20.1.3 Live View Interface ...... .. ......... .. ......... ........... ........... ..... 108
20.1.4 Controlling PTZ Cameras......... ........... ......... ........... ....... 109
20.1.5 Viewing Snapshots and Videos with Local Files ........ .......... 110
20.1.6 Using Playback Mode on iPhone ..... .................... ........... . 111
20.1.7 Enabling Push Notifications .................. ........... ........... .... 112
20.1.8 Using the Event List ..... ........... ........... .................... ....... 114
20.1.9 Using Favorites.... .. ......... .. ......... ........... ........... ............ 115
20.1.10 Using the E-Map ........... ......... .. ......... .. ........... .............. 116
20.1.11 Device Manager......... ........... ........... ........... ........... ...... 118
20.1.12 Adding Devices Using an IP or DDNS Address
(Advanced)...... ......... ........... ........... ........... ........... ...... 119
20.2 iPad ........... ........... .................... ........... ........... ........... .......... 121
20.2.1 Prerequisites....... ........... ........... ........... .................... ... 121
20.2.2 Connecting to your system on an iPad ....... ........... ............ 121
20.2.3 Live View Interface ...... .. ......... .. ......... ........... ........... ..... 122
20.2.4 Controlling PTZ Cameras......... ........... ......... ........... ....... 123
20.2.5 Using Playback Mode on iPad. ......... .. ......... ........... ......... 124
20.2.6 Using Local File to View Manual Recordings ........ ........... ... 126
20.2.7 Enabling Push Notifications .................. ........... ........... .... 127
20.2.8 Using the Event List ..... ........... ........... .................... ....... 129
20.2.9 Using Favorites.... .. ......... .. ......... ........... ........... ............ 130
20.2.10 Using the E-Map ........... ......... .. ......... .. ........... .............. 131
20.2.11 Using the Device Manager .......... ........... .................... .... 133
20.2.12 Adding Devices Using an IP or DDNS Address
(Advanced)...... ......... ........... ........... ........... ........... ...... 133
20.3 Android ... ........... ........... .................... .. ......... .. ......... .. ......... .. 136
20.3.1 Prerequisites....... ........... ........... ........... .................... ... 136
20.3.2 Connecting to your System on Android ....... ......... .. ......... .. 136
20.3.3 Live View Interface ...... .. ......... .. ......... ........... ........... ..... 137
20.3.4 Controlling PTZ Cameras......... ........... ......... ........... ....... 138
20.3.5 Viewing Snapshots and Videos with Local Files ........ .......... 139
20.3.6 Using Playback Mode on Android ..... ........... ......... ........... 139
20.3.7 Enabling Push Notifications .................. ........... ........... .... 141
20.3.8 Using the Event List ..... ........... ........... .................... ....... 142
20.3.9 Using Favorites.... .. ......... .. ......... ........... ........... ............ 142
20.3.10 Using the E-Map ........... ......... .. ......... .. ........... .............. 144
20.3.11 Device Manager......... ........... ........... ........... ........... ...... 145
20.3.12 Adding Devices Using an IP or DDNS Address
(Advanced)...... ......... ........... ........... ........... ........... ...... 146
21 DDNS Setup (Advanced) ............ ........... ........... ........... ........... .......... 148
21.1 Accessing your System within a Local Network (LAN)........ .. ......... .. 148
21.1.1 Step 1 of 3: Connect your System to Your Router ..... ........... 148
21.1.2 Step 2 of 3: Obtain the System’s Local IP Address . ........... ... 149
21.1.3 Step 3 of 3: Connect to the System’s Local IP
Address .. .. ......... .. ......... .. .................... ........... ........... . 149
21.2 DDNS Setup—Access your System Remotely over the
Internet...... ........... ........... ........... ........... ........... ......... ........... 151
21.2.1 Step 1 of 4: Port Forwarding ...... .................... .. ......... .. .... 152
21.2.2 Step 2 of 4: Create a DDNS Account . ........... ........... ......... 152
#LX400051; r. 1.0/23100/23101; en-US
viii
Page 9
Table of contents
21.2.3 Step 3 of 4: Enable DDNS on the System ............ ........... ... 153
21.2.4 Step 4 of 4: Connect to the System’s DDNS Address ........ ... 154
22 RTSP Streaming (Advanced). ........... ........... ......... ........... ........... ....... 158
23 Connecting a PTZ Camera (M3200 / M4200 SERIES) . ........... ........... ..... 160
23.1 Controlling a PTZ Camera (Local DVR).. .. ......... .. ........... .............. 160
23.2 Advanced PTZ Controls ....... ......... ........... ........... ........... .......... 161
23.2.1 Presets ....... .. ......... ........... ........... ........... ........... ........ 162
23.2.2 Tours...... .. ......... .. ......... .. .................... ........... ........... . 162
23.2.3 Pattern.. ........... ......... .. ......... .. ......... .. .................... ..... 163
23.2.4 Auto Scan .................. ........... ........... ......... .. ......... .. .... 163
24 M3200 / M4200 SERIES Hard Drive Installation.... ........... ........... .. ........ 165
24.1 Installing a Hard Drive.............. ........... ........... ........... ......... .. .... 165
24.2 Removing the Hard Drive................... ........... ........... .. ......... ...... 166
24.3 Formatting Hard Drives .................. .. ......... .. ......... .. ......... ......... 167
25 Troubleshooting ..................... ........... ........... .. ......... ........... ........... .. 169
26 M3200 Series System Specifications ........... ......... ........... ........... ....... 171
27 M4200 Series System Specifications ........... ......... ........... ........... ....... 174
28 Notices.... ......... ........... .. ......... .. ......... .. ......... ........... ........... ............ 177
28.1 FCC/IC Notice.......... ........... ......... .. ......... .. ......... .. .................. 177
28.2 Modification.......... ........... ......... .. ........... ........... ......... ........... . 177
28.3 ROHS ........... ........... .. ......... .. ......... ........... ........... ................ 177
#LX400051; r. 1.0/23100/23101; en-US
ix
Page 10
Page 11
1
Important Safeguards
In addition to the careful attention devoted to quality standards in the manufacturing process of your product, safety is a major factor in the design of every instrument. However,
safety is your responsibility too. This sheet lists important information that will help to ensure your enjoyment and proper use of the product and accessory equipment. Please read
them carefully before operating and using your product.
1.1 General Precautions
1. All warnings and instructions in this manual should be followed.
2. Remove the plug from the outlet before cleaning. Do not use liquid aerosol detergents.
Use a water-dampened cloth for cleaning.
3. Do not use this product in humid or wet places.
4. Keep enough space around the product for ventilation. Slots and openings in the storage cabinet should not be blocked.
5. It is highly recommended to connect the product to a surge protector to protect from
damage caused by electrical surges. It is also recommended to connect the product to
an uninterruptible power supply (UPS), which has an internal battery that will keep the
product running in the event of a power outage.
CAUTION
Maintain electrical safety. Power line operated equipment or accessories connected to this product
should bear the UL listing mark or CSA certification mark on the accessory itself and should not be modified so as to defeat the safety features. This will help avoid any potential hazard from electrical shock or
fire. If in doubt, contact qualified service personnel.
1.2 Installation
1. Read and Follow Instructions - All the safety and operating instructions should be
read before the product is operated. Follow all operating instructions.
2. Retain Instructions - The safety and operating instructions should be retained for future reference.
3. Heed Warnings - Comply with all warnings on the product and in the operating
instructions.
4. Polarization - Do not defeat the safety purpose of the polarized or grounding-type
plug.
A polarized plug has two blades with one wider than the other.
A grounding type plug has two blades and a third grounding prong.
The wide blade or the third prong are provided for your safety.
If the provided plug does not fit into your outlet, consult an electrician for replacement
of the obsolete outlet.
#LX400051; r. 1.0/23100/23101; en-US
1
Page 12
1
Important Safeguards
5. Power Sources - This product should be operated only from the type of power source
indicated on the marking label. If you are not sure of the type of power supplied to your
location, consult your video dealer or local power company. For products intended to
operate from battery power, or other sources, refer to the operating instructions.
6. Overloading - Do not overload wall outlets or extension cords as this can result in the
risk of fire or electric shock. Overloaded AC outlets, extension cords, frayed power
cords, damaged or cracked wire insulation, and broken plugs are dangerous. They
may result in a shock or fire hazard. Periodically examine the cord, and if its appearance indicates damage or deteriorated insulation, have it replaced by your service
technician.
7. Power-Cord Protection - Power supply cords should be routed so that they are not
likely to be walked on or pinched by items placed upon or against them. Pay particular
attention to cords at plugs, convenience receptacles, and the point where they exit
from the product.
8. Surge Protectors - It is highly recommended that the product be connected to a
surge protector. Doing so will protect the product from damage caused by power
surges. Surge protectors should bear the UL listing mark or CSA certification mark.
9. Uninterruptible Power Supplies (UPS) - Because this product is designed for continuous, 24/7 operation, it is recommended that you connect the product to an uninterruptible power supply. An uninterruptible power supply has an internal battery that will
keep the product running in the event of a power outage. Uninterruptible power supplies should bear the UL listing mark or CSA certification mark.
10. Ventilation - Slots and openings in the case are provided for ventilation to ensure reli-
able operation of the product and to protect it from overheating. These openings must
not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should never be placed
near or over a radiator or heat register. This product should not be placed in a built-in
installation such as a bookcase or rack unless proper ventilation is provided and the
product manufacturer’s instructions have been followed.
11. Attachments - Do not use attachments unless recommended by the product manufacturer as they may cause a hazard.
12. Water and Moisture - Do not use this product near water — for example, near a bath
tub, wash bowl, kitchen sink or laundry tub, in a wet basement, near a swimming pool
and the like.
13. Heat - The product should be situated away from heat sources such as radiators, heat
registers, stoves, or other products (including amplifiers) that produce heat.
14. Accessories - Do not place this product on an unstable cart, stand, tripod, or table.
The product may fall, causing serious damage to the product. Use this product only
with a cart, stand, tripod, bracket, or table recommended by the manufacturer or sold
with the product. Any mounting of the product should follow the manufacturer’s instructions and use a mounting accessory recommended by the manufacturer.
15. Camera Extension Cables – Check the rating of your extension cable(s) to verify
compliance with your local authority regulations prior to installation.
16. Mounting - The cameras provided with this system should be mounted only as instructed in this guide or the instructions that came with your cameras, using the provided mounting brackets.
#LX400051; r. 1.0/23100/23101; en-US
2
Page 13
1
Important Safeguards
17. Camera Installation - Cameras are not intended for submersion in water. Not all cameras can be installed outdoors. Check your camera environmental rating to confirm if
they can be installed outdoors. When installing cameras outdoors, installation in a
sheltered area is required.
1.3 Service
1. Servicing - Do not attempt to service this product yourself, as opening or removing
covers may expose you to dangerous voltage or other hazards. Refer all servicing to
qualified service personnel.
2. Conditions Requiring Service - Unplug this product from the wall outlet and refer
servicing to qualified service personnel under the following conditions:
• When the power supply cord or plug is damaged.
• If liquid has been spilled or objects have fallen into the product.
• If the product has been exposed to rain or water.
• If the product has been dropped or the cabinet has been damaged
• If the product does not operate normally by following the operating instructions. Ad-
just only those controls that are covered by the operating instructions. Improper adjustment of other controls may result in damage and will often require extensive
work by a qualified technician to restore the product to its normal operation.
• When the product exhibits a distinct change in performance. This indicates a need
for service.
3. Replacement Parts - When replacement parts are required, have the service technician verify that the replacements used have the same safety characteristics as the original parts. Use of replacements specified by the product manufacturer can prevent fire,
electric shock, or other hazards.
4. Safety Check - Upon completion of any service or repairs to this product, ask the
service technician to perform safety checks recommended by the manufacturer to determine that the product is in safe operating condition.
1.4 Use
1. Cleaning - Unplug the product from the wall outlet before cleaning. Do not use liquid
cleaners or aerosol cleaners. Use a damp cloth for cleaning.
2. Product and Cart Combination - When product is installed on a cart, product and
cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to overturn.
3. Object and Liquid Entry - Never push objects of any kind into this product through
openings as they may touch dangerous voltage points or “short-out” parts that could
result in a fire or electric shock. Never spill liquid of any kind on the product.
4. Lightning - For added protection of this product during a lightning storm, or when it is
left unattended and unused for long periods of time, unplug it from the wall outlet and
disconnect the antenna or cable system. This will prevent damage to the product due
to lightning and power line surges.
#LX400051; r. 1.0/23100/23101; en-US
3
Page 14
2
M3200 Series Features
Features
• 720p @ Real-time (30/25fps per channel)
• Supports 2.0 MP (1080p @ 15fps per channel)
• See double the detail of 960H
• Supports MPX HD cameras and standard analog cameras
• Ideal for retrofit using existing coax cable
• Easy, Secure Cloud connection
• Zero video latency
• Cabling up to 2300 ft. (700m)
• Duplex transmission for camera control (PTZ, focus, alarm trigger)
• FLIR DDNS service option
• H.264 video compression
• HDMI/VGA simultaneous video output
• Supports audio transmission, 4 Audio In / 1 Out
• Supports 2x HDD up to 4TB (8TB total), 2x USB 2.0 ports
• RS-485 supports Pelco D & P PTZ
• Drive mirroring to second internal HDD
#LX400051; r. 1.0/23100/23101; en-US
4
Page 15
3
M4200 Series Features
Features
• Supports 2.1 MP (1080p @ 30/25fps per channel)
• Full HD 1080P recording provides the most detailed picture
• Supports MPX HD cameras and standard analog cameras
• Ideal for retrofit using existing coax cable
• Easy, Secure Cloud connection
• Zero video latency
• Cabling up to 2300 ft. (700m)
• Duplex transmission for camera control (PTZ, focus, alarm trigger)
• FLIR DDNS service option
• H.264 video compression
• HDMI/VGA simultaneous video output
• Supports audio transmission, 4 Audio In / 1 Out
• Supports 2x HDD up to 4TB (8TB total), 2x USB 2.0 ports
• RS-485 supports Pelco D & P PTZ
• Drive mirroring to second internal HDD
#LX400051; r. 1.0/23100/23101; en-US
5
Page 16
4
Getting Started (M3200 / M4200 SERIES)
The system comes with the following components:
DVR (Digital Video Recorder)
USB mouse Ethernet cable
Hard drive size, number of channels, and camera configuration may vary by model. Please
refer to your package for specific details. Check your package to confirm that you have received the complete system, including all components shown above.
12V DC power supply + power
cable
Remote control
(may not be exactly as shown)
Quick start guides
#LX400051; r. 1.0/23100/23101; en-US
6
Page 17
5
Series Front Panel (M3200 / M4200 SERIES)
5.1 M3200 / M4200 Series
1. USB Port: Connect a USB mouse (included) or connect a USB flash drive (not included) for data backup or firmware upgrades.
2. IR: Not supported.
3. Channel Indicators: Glow when camera is connected to the corresponding channel.
4. Playback Controls:
•
Pause/Play: In live view, press to enter playback mode. Press to play/pause
playback.
•
Reverse: Press to reverse playback/pause playback.
•
•
•
•
5. Function Buttons:
• REC: Press to open manual recording controls.
• FN: Performs special functions in some menus.
• SHIFT: During text input, press to switch input types.
• ESC: In menus, press to go back / exit menus. In playback, press to return to live
6. Directional Buttons:
• ENTER: From live view, press once to open the System Information screen; press
• Directional Buttons: Press to move cursor in menus. In live view, press up to
7. Power Button: Press and hold to power off the system. Press to power the system
back on.
Fast: Press to increase playback speed.
Next: Press to skip to next video.
Previous: Press to skip to previous video.
Slow: Press for slow playback.
view.
twice to open the Main Menu. In menus, press to confirm menu options.
change split screen layout; press left / right to select channels when single-channel
mode is selected.
#LX400051; r. 1.0/23100/23101; en-US
7
Page 18
5
Series Front Panel (M3200 / M4200 SERIES)
8. IR Receiver and LED Indicators: IR receiver for the remote control. Keep the IR receiver clear from obstructions.
LED Indicators:
• POWER: Glows to indicate the system is on.
• HDD: Glows to indicate hard drive is in normal state. Turns off when there is a hard
drive error.
• NET: Glows when network is in normal state. Turns off for network error.
#LX400051; r. 1.0/23100/23101; en-US
8
Page 19
6
Rear Panel (M3200 / M4200 SERIES)
6.1 M3200 Series
M3204 (4–Channel)
M3208 (8–Channel)
1. On / Off switch: Turns the DVR on or off.
2. Alarm IO: Connect alarm/sensor devices (not included).
3. DC12V: Connect the included AC power adapter.
4. A/B: Connect RS485 cables for PTZ cameras (not included).
5. LAN: Connect a CAT 5 RJ45 Ethernet cable for local and remote connectivity.
6. RS232: Serial connection for PTZ keyboard (not included).
7. VGA: Connect a VGA monitor (not included) to view the system interface.
8. USB port(s): Connect a USB mouse (included) or USB flash drive (not included) for
data backup or firmware updates.
9. HDMI: Connect to an HDMI monitor or TV (not included) to view the system interface.
10. Audio OUT: RCA audio output.
11. Audio IN: RCA audio input for up to 4 channels.
12. Video input: Connect FLIR MPX or analog cameras to the system.
M3216 (16–Channel)
1. Alarm IO: Connect alarm/sensor devices.
2. A/B: Connect RS485 cables for PTZ cameras (not included).
3. DC12V: Connect the included AC power adapter.
4. On / Off switch: Turns the DVR on or off.
5. LAN: Connect a CAT 5 RJ45 Ethernet cable for local and remote connectivity.
6. RS232: Serial connection for PTZ keyboard (not included).
7. VGA: Connect a VGA monitor (not included) to view the system interface.
#LX400051; r. 1.0/23100/23101; en-US
9
Page 20
6
Rear Panel (M3200 / M4200 SERIES)
8. USB port(s): Connect a USB mouse (included) or USB flash drive (not included) for
data backup or firmware updates.
9. HDMI: Connect to an HDMI monitor or TV (not included) to view the system interface.
10. Audio OUT: RCA audio output.
11. Audio IN: RCA audio input for up to 4–channels.
12. Video input: Connect FLIR MPX or analog cameras.
6.2 M4200 Series
M4204 (4–Channel)
1. On / Off switch: Turns the DVR on or off.
2. Alarm IO: Connect alarm/sensor devices.
3. DC12V: Connect the included AC power adapter.
4. A/B: Connect RS485 cables for PTZ cameras (not included).
5. LAN: Connect a CAT 5 RJ45 Ethernet cable for local and remote connectivity.
6. RS232: Serial connection for PTZ keyboard (not included).
7. VGA: Connect a VGA monitor (not included) to view the system interface.
8. USB port(s): Connect a USB mouse (included) or USB flash drive (not included) for
data backup or firmware updates.
9. HDMI: Connect to an HDMI monitor or TV (not included) to view the system interface.
10. Audio OUT: RCA audio output.
11. Audio IN: RCA audio input for up to 4 channels.
12. Video input: Connect FLIR MPX or analog cameras to the system.
M4208 (8–Channel)
1. Alarm IO: Connect alarm/sensor devices.
2. A/B: Connect RS485 cables for PTZ cameras (not included).
3. DC12V: Connect the included AC power adapter.
4. On / Off switch: Turns the DVR on or off.
5. LAN: Connect a CAT 5 RJ45 Ethernet cable for local and remote connectivity.
6. RS232: Serial connection for PTZ keyboard (not included).
7. VGA: Connect a VGA monitor (not included) to view the system interface.
8. USB port(s): Connect a USB mouse (included) or USB flash drive (not included) for
data backup or firmware updates.
9. HDMI: Connect to an HDMI monitor or TV (not included) to view the system interface.
10. Audio OUT: RCA audio output.
11. Audio IN: RCA audio input for up to 4–channels.
#LX400051; r. 1.0/23100/23101; en-US
10
Page 21
6
Rear Panel (M3200 / M4200 SERIES)
12. Video input: Connect FLIR MPX or analog cameras.
#LX400051; r. 1.0/23100/23101; en-US
11
Page 22
7
Basic Setup (M3200 / M4200 SERIES)
7.1 Step 1: Connect the BNC Cameras
• Connect FLIR MPX or analog cameras to the Video Input ports on the rear panel of
the DVR.
Push and twist the BNC connector clockwise to secure it to the BNC port.
NOTE
For more information on MPX cameras and cabling, see 8 About MPX, page 16.
7.2 Step 2: Connect the Mouse
• Connect a USB mouse (included) to one of the USB ports.
7.3 Step 3: Connect the Ethernet Cable
• Connect an Ethernet cable (included) to the LAN port on the rear panel of the DVR.
Connect the other end of the Ethernet cable to a router on your network.
#LX400051; r. 1.0/23100/23101; en-US
12
Page 23
7
Basic Setup (M3200 / M4200 SERIES)
7.4 Step 4: Connect the Monitor
• Connect the included HDMI cable from the HDMI port to the TV or monitor
(recommended).
OR
• Connect a VGA cable (not included) from the VGA port to the monitor.
1. VGA port.
2. HDMI port.
7.5 Step 5: Connect the Power Adapter and Power on the DVR
1. Connect the included power adapter to the DC 12V port. Connect the end of the power
adapter to a wall socket or a surge protector.
2. Turn the power switch to ON to turn on the DVR.
At startup, the system performs a basic system check and runs an initial loading sequence.
After a few moments, the system loads a live display view.
7.6 Step 6: Upgrade Firmware to Latest Version (if Available)
If a firmware upgrade is available, you will be asked to install it once the system starts up.
It is required to upgrade your system firmware and client software or mobile apps to the latest version to enable remote connection to the system.
If a firmware upgrade is available:
1. After startup, a notification will appear asking you to upgrade the firmware. Click OK to
upgrade.
#LX400051; r. 1.0/23100/23101; en-US
13
Page 24
7
Basic Setup (M3200 / M4200 SERIES)
2. Enter the system user name (default: admin) and password (default: 000000) and
click OK. Wait for the firmware update to complete. The system will restart once the
firmware has been upgraded.
WARNING
DO NOT POWER OFF THE SYSTEM OR DISCONNECT THE POWER CABLE DURING FIRMWARE INSTALLATION
7.7 Step 7: Verify Camera Image
• Power on the cameras, and then verify the camera video quality before mounting the
cameras to a permanent location.
• Always verify the outdoor rating of your camera before installing it in a permanent
location.
7.8 Step 8: Set the Time
• Set the system time and date for accurate video time stamps. Videos with inaccurate
times may not be valid as surveillance evidence.
• For details on setting the system time, see 12 Setting The Time, page 25.
7.9 Default System Password & Port Numbers
CAUTION
By default, the system user name is admin and the password is 000000. It is essential that you create
your own password. For details, see 16 Managing Passwords and User Accounts, page 39.
A user name and password is required to log in to the system. After logging on using a
computer or mobile device the first time, you will be asked to create a custom password
for the system.
Local system and remote connectivity (LAN & Internet) user name and password:
• Username: admin
• Password: 000000
Default ports for DDNS remote access:
• Port 80 (HTTP port)
• Port 35000 (Client port)
7.9.1 FLIR Cloud™
This system features the exclusive FLIR Cloud™. This is a cloud service that allows you to
connect to your system over the Internet via a secure handshake with our servers. This
means you can easily connect to your system without requiring any network configuration.
For details on setting up your system to connect to the Internet using FLIR
Cloud™:
• See 18 Connecting to Your System Over the Internet on PC or Mac, page 76.
OR
• See 20 Connecting to your System Using Smartphone or Tablet Apps, page 107.
Connectivity using FLIR’s free DDNS service is also available, and requires the ports listed
above to be port forwarded on your router. See 21 DDNS Setup (Advanced), page 148 for
DDNS setup instructions.
#LX400051; r. 1.0/23100/23101; en-US
14
Page 25
7
Basic Setup (M3200 / M4200 SERIES)
7.10 Quick Access to System Information
To quickly open a window that displays vital system information:
• Right-click to open the Quick Menu and click Info. Enter the system user name (default:
admin) and password (default: 000000).
OR
• Press the ENTER button on the front panel.
OR
• Press the ENTER button on the remote control.
NOTE
The QR code shown in the System Info screen can be scanned during mobile setup to enter the system’s Device ID.
#LX400051; r. 1.0/23100/23101; en-US
15
Page 26
8
About MPX
FLIR MPX™ is a revolutionary video surveillance format powered by HD-CVI technology.
MPX delivers megapixel picture quality over coax, meaning you can upgrade your existing
analog systems to HD resolution (1MP & 2.1MP) over a single coax cable (RG59 & RG6
compatible).
NOTE
The DVRs covered in this manual are compatible with 1MP (720p) and 2MP (1080p) cameras.
8.1 What types of cabling and run lengths does MPX work with?
MPX allows a maximum cable run of up to 2300ft (700m) @ 720p or up to 2000ft (610m)
@ 1080p, depending on the type of cable used (see below). It is required that the cable
runs be made in a single run between camera and DVR, as daisychaining multiple cable
runs together can prevent the DVR from getting a picture from the camera or may impact
image quality. MPX supports standard UTP baluns for use with CAT5E or CAT6 cabling in
your installation. The baluns should have a 12V and BNC connection at both ends. You
can run up to 300ft (91m) per segment of CAT5E or CAT6.
Cable Type Maximum Run Length
RG59 20AWG Conductor 95% Braid CSA/UL or C
(UL) approved
RG6 20AWG Conductor 95% Braid CSA/UL or C
(UL) approved
Analog CCTV Balun 720p: Up to 300ft (91m)
720p: Up to 1500ft (455m)
1080p: Up to 1000ft (300m)
720p: Up to 2300ft (700m)
1080p: Up to 2000ft (600m)
1080p: Up to 300ft (91m)
1
1. Long cable runs over 1000ft may be affected by electromechanical interference (EMI), which can increase the
amount of noise in the picture in some installations.
#LX400051; r. 1.0/23100/23101; en-US
16
Page 27
9
Mouse Control
The mouse is the primary control device for the system. To connect a USB mouse:
• Connect a USB mouse to the USB port on the front or rear panel.
1. Left-button:
• In live view, click to open the Navigation Bar. Right-click to close the navigation bar.
• In live view, while in a split-screen display mode, double-click an individual channel
to view it in full-screen. Double-click again to return to the split-screen display mode.
• While navigating menus, click to open a menu option.
2. Right-button:
• During live view, right-click anywhere on the screen to open the Quick Menu.
• Within system menus, right-click to exit menus.
3. Scroll wheel: In live view, use the scroll wheel to zoom in/out.
#LX400051; r. 1.0/23100/23101; en-US
17
Page 28
10
Remote Control
1. Power: Press and hold to power off the system. Press to power on.
2. Playback controls:
•
Pause/Play: In live view, press to enter playback mode. Press to play/pause
playback.
•
Reverse: Press to reverse playback/pause playback.
•
•
•
•
3. Esc: In menus, press to go back / exit menus. In playback, press to return to live view.
4. Directional keys:
• Enter: Press once to open the System Information screen; press twice to open the
• Press
• Press
5. Mult: Press to switch between full-screen and split-screen layouts.
6. Number keys:
• 1~0: In live view, press to open channels in full-screen.
• In menus, press to input numbers or text input.
• Shift: Press to change input types.
7. Add: Configure remote control address. See below for details.
8. Rec: Press to open manual record menu.
9. Fn: Press to perform special functions in some menus.
Fast: Press to increase playback speed.
Next: Press to skip to next video.
Previous: Press to skip to previous video.
Slow: Press for slow playback.
Navigation Bar. Press to confirm menu selections.
to move the menu cursor.
to change menu options.
#LX400051; r. 1.0/23100/23101; en-US
18
Page 29
10
Remote Control
10.1 Setting the Remote Control Address
If you have more than one system, you can set up your remote control to pair with a specific system.
To set the remote control address:
1. Right-click and click Main Menu. Enter the system user name (default: admin) and
password (default: 000000).
2. Click
>General>General.
3. Under Device No., enter the address number you would like to assign to the remote
control.
4. Click OK.
5. Using the remote control, press Add. Then enter the address number and press Enter.
#LX400051; r. 1.0/23100/23101; en-US
19
Page 30
11
Using the System
Use the system’s graphical on-screen display to navigate menus and configure options
and settings.
11.1 On-Screen Display
The system shows the following for all display views:
1. Display area:
• Double-click on a channel to view in full-screen; double-click again to return to split
screen.
• Right-click to open the Quick Menu.
• Left-click to open the Navigation Bar.
• Move the mouse to the top of a channel to view the Camera Toolbar.
• Click-and-drag cameras to rearrange the channel display. This does not affect the
channels each camera is connected or recording to.
2. Channel name
3. C: Camera is continuously recording.
4. M: Motion has been detected.
5. Date & time: Current system date and time. For details on setting the date and time,
see 12 Setting The Time, page 25.
#LX400051; r. 1.0/23100/23101; en-US
20
Page 31
11
Using the System
11.2 Using the Quick Menu
The Quick menu gives you access to the system’s key functions. To access the Quick
Menu, right-click the screen during live view.
The Quick Menu has the following options:
• View: Select a camera in full-screen or select a multi-channel display.
• Pan/Tilt/Zoom: Access controls for PTZ cameras (not included).
• Color Setting: Configure color settings for cameras.
• Info: Opens the system information window.
• Sequence: Click to start/stop sequence mode.
• In sequence mode, the system will automatically cycle through connected cameras
every few seconds.
• A
will appear to show that sequence mode is on.
• Click the icon to pause sequence mode on the channel that is currently shown (icon
changes to
). Click again to resume sequence mode.
• Right-click and select Sequence to return to normal viewing mode.
• Search: Search/playback recorded video. See 14 Search (Playback), page 28.
• Manual: Open the Record menu to select manual recording options. See 13.3 Setting
up Scheduled or Manual Recording, page 26.
• Main Menu: Open the Main Menu. See 17 Using the Main Menu, page 43.
11.3 Adjusting Color Settings
Use the Color Settings menu to adjust color settings for your cameras.
To adjust color settings:
1. Right-click on the channel you would like to configure and select Color Setting. Enter
the system password if prompted.
#LX400051; r. 1.0/23100/23101; en-US
21
Page 32
11
Using the System
2. Adjust the Hue, Brightness, Contrast, and Saturation settings that the camera will
use. To enable custom Gain controls, check Gain and use the slider to configure the
gain level.
3. Click OK to save changes.
11.4 Using the Navigation Bar
The Navigation Bar gives quick access to certain functions and menus.
To open the Navigation bar:
• Left click on the screen to open the Navigation Bar. The Navigation Bar has the following options:
1. Main Menu.
2. Collapse.
3. Select display layout.
4. Sequence: Click to start/stop sequence mode.
5. PTZ: Click to open PTZ controls.
6. Camera: Click to open camera image settings.
7. Search: Search and playback recorded video. See 19.4 Playback, page 88.
8. Alarm Status: View alarms in progress. See 17.2.4 Alarm Status, page 49.
9. Channel Info: Click to access status information about connected cameras.
10. Network: Configure network settings for your system. See 17.3.1 Network, page 53.
11. HDD Manager: Manage hard drives connected to the system. See 17.3.18 Format-
ting the Hard Drive, page 66.
12. USB Manager: Click to access options for connected USB thumb drives (not in-
cluded). You can backup video, logs, or system configurations and install firmware
upgrades.
13. System Update: Click to check for firmware upgrades. Your system must be con-
nected to the Internet to check for firmware upgrades.
11.5 Using the Camera Toolbar
The Camera Toolbar is used to perform actions on a specific channel.
#LX400051; r. 1.0/23100/23101; en-US
22
Page 33
11
Using the System
To access the Camera Toolbar:
• Move the mouse to the top of the channel display. The Camera Toolbar has the following options:
1. Quick Playback.
2. Digital zoom.
3. Real-time backup.
4. Snapshot.
5. Mute/unmute audio.
11.5.1 Using Quick Playback
Quick Playback is used to playback the last 5~60 minutes of video from the selected channel. You can also access Quick Playback in split-screen mode, while still viewing live video
from the other channels.
To use Quick Playback:
1. Move your mouse to the top of the channel display and click
NOTE
By default, the system will begin playback from 5 minutes ago. You can increase this to up to 60 minutes using the Realtime Play setting in Main Menu>Setting>General.
.
2. Right-click to exit Quick Playback.
11.5.2 Using Digital Zoom in Live Display
1. Move your mouse to the top of the channel display and click
to activate digital
zoom. A check mark will appear in the icon to indicate digital zoom is activated.
NOTE
You may activate digital zoom in multiple channels at the same time.
2. Click and drag inside the channel to zoom in.
• Click and drag to pan the zoom area.
• Right-click to zoom out and select a new zoom area.
• Click
to disable digital zoom. Note that the channel will remain at the same
zoom level until you right-click inside it.
11.5.3 Using Real-time Backup
Real-time backup allows you to save footage from the live display to a USB thumb drive
(not included) or external hard drive (not included).
#LX400051; r. 1.0/23100/23101; en-US
23
Page 34
11
Using the System
To use Real-time Backup:
1. Insert the USB thumb drive or external hard drive into one of the USB ports on the
system.
2. Move your mouse to the top of the channel display and click
to start Real-time
Backup.
3. Click
If the system prompts you to log in, you will need to click
logging in.
again to end Real-time Backup. The file is saved to your USB device.
NOTE
again to start Real-time Backup after
11.6 Using the Virtual Keyboard
The Virtual Keyboard is used to input text or numeric values in certain menus.
1. Backspace.
2. Enter capital letters.
3. Confirm entry.
#LX400051; r. 1.0/23100/23101; en-US
24
Page 35
12
Setting The Time
CAUTION
It is highly recommended to set the date and time when first setting up your system.
Inaccurate time stamps may render your footage unusable for court evidence.
To set the date and time:
1. In the main viewing mode, right-click and click Main Menu.
2. Log in using the system user name (default: admin) and password (default: 000000).
3. Click
4. Under System Time, enter the current time and select your time zone. Then, click OK.
5. Check DST to enable auto Daylight Savings Time updates.
• You can adjust the Start Time and End Time for Daylights Savings Time if the default settings do
not match your region.
• Under DST Type, select Day of Week to set the start and end time based on a day and week (e.g.
2nd Sunday in March), or select Date to set the start and end time to a specific date.
6. (Optional) Check NTP to sync your system with an Internet time server. Click Manual
Update to instantly update the time.
and select Setting. Click General and select the Date&Time tab.
NOTE
NOTE
• Your system must have a constant connection to the Internet to use NTP.
• (Advanced) You can enter a custom NTP server under Server IP and Port, and you can select
how often the system will sync the time using Interval.
7. Click Apply to save changes.
#LX400051; r. 1.0/23100/23101; en-US
25
Page 36
13
Recording
By default, the system is set to immediately record video from connected cameras continuously, 24 hours a day. You can customize the recording settings according to your needs.
13.1 Video Recording Types
The system supports the following recording types.
• Recording—Continuous: Normal, continuous recording. A
recording is in progress.
• Recording—Motion: The system records when motion is detected by the camera. An
icon is shown when motion is detected.
13.2 Main Stream and Sub Stream
The system employs two video recording streams, a Main Stream and a Sub Stream. Both
Main Stream and Sub Stream recording are enabled by default.
The Main Stream records high quality video to your system’s hard drive.
The Sub Stream records lower resolution video for efficient streaming to devices over the
Internet. Sub Stream recording must be enabled to view video recordings on a computer
or mobile device.
You can configure the video quality parameters for the Main Stream or Sub Stream. For
details, see 17.1.2 Configuring Recording Quality, page 44.
13.3 Setting up Scheduled or Manual Recording
You can set the system to record based on a schedule or you can manually turn recording
on and off. By default, the system is set to record on an always on recording schedule.
To configure the recording schedule, see 17.3.14 Configuring the Video Recording Sched-
ule, page 63.
To select between scheduled and manual recording:
1. Right-click and then select Manual>Record.
icon is shown when
#LX400051; r. 1.0/23100/23101; en-US
26
Page 37
Recording13
2. Under Main Stream, select how the system will record the Main Stream for each
channel.
• Schedule: Main Stream Recording will follow the recording schedule.
• Manual: The system will record the Main Stream continuously as long as this option
is checked.
• Stop: The system will not record the Main Stream for this channel. This option is
not recommended.
3. Under Sub Stream, select how the system will record the Sub Stream for each
channel.
• Schedule: Sub Stream Recording will follow the recording schedule.
• Manual: The system will record the Sub Stream continuously as long as this option
is checked.
• Stop: The system will not record the Sub Stream for this channel.
4. Under Snapshot, select Enable to enable snapshot recording on each channel. Or,
select Disable to disable snapshot recording.
5. Click OK to save changes.
13.4 Configuring Hard Drive Overwrite
When the hard drive is full, the system will overwrite the oldest recordings by default. This
is recommended, as it makes sure that your system will continue to record without any input from you. You can also set the system to stop recording once the hard drive is full.
To configure hard drive overwrite:
1. Right-click and select Main Menu. Click
> Setting>General>General.
2. Under HDD Full, select Overwrite for the system to overwrite the oldest recordings
when the hard drive is full. Or, select Stop Record for the system to stop recording
when the hard drive is full.
3. Click OK to save changes.
#LX400051; r. 1.0/23100/23101; en-US
27
Page 38
14
Search (Playback)
Search mode is used to navigate and playback recorded video files on the system.
14.1 Playing Back Video from the Hard Drive
1. From live view, right-click and then click Search.
2. Log in using the system user name (default: admin) and password (default: 000000).
3. Configure the following:
3.1. Use the calendar on the right to select the day to playback.
3.2. Use the drop-down menus to select the channels you would like to playback.
NOTE
Click the display options (
3.3. Click inside the video bar to select the playback time. The system will begin
playing back at the selected time.
) to playback multiple channels simultaneously.
#LX400051; r. 1.0/23100/23101; en-US
28
Page 39
14
Search (Playback)
14.2 Playback Controls
1. Select playback device.
2. Calendar: Select the day to playback.
3. Channel select: Select channels to playback.
4. Video clip backup: Select video clip start and end times.
5. Backup video clip: Click to save selected clip.
6. Playback Bar: Click inside the bar to select a playback time.
7. Zoom Playback Bar: Select scope of time bar.
8. Recording types: Click to show/hide recording types.
9. Speed up.
10. Slow.
11. Previous/next frame.
12. Play backward.
13. Stop.
14. Play.
14.3 Playing Back from a USB Drive
If you have video files saved to a USB thumb drive (not included) or external hard drive
(not included), you can play them back using the system.
To play back from a USB drive:
1. Connect the USB thumb drive (not included) or USB external hard drive (not included)
with video files on it into a USB port on the system.
2. From live view, right-click and click Search.
3. Log in using the system user name (default: admin) and password (default: 000000).
#LX400051; r. 1.0/23100/23101; en-US
29
Page 40
14
Search (Playback)
4. Click From ReadWrite Hdd and select From IO Device. Click Browse to open the
USB drive and manually select the video file.
5. Double click the video file you would like to open.
#LX400051; r. 1.0/23100/23101; en-US
30
Page 41
15
Backup
Backup video files to external USB flash drive (not included) or self-powered USB external
hard drive (not included).
NOTE
USB external hard drives must be formatted in the FAT32 file format to be used with the system.
15.1 Formatting the USB Thumb Drive
It is recommended to format your USB thumb drive (not included) before using it with the
system.
CAUTION
Formatting the USB device will permanently erase all data.
To format a USB device:
1. Insert a USB thumb drive (not included) into one of the USB ports.
2. From live view, right-click and then select Main Menu. Login if prompted.
3. Click
4. Select the USB device you would like to format under Device Name and click Browse.
5. Click Format. Click OK to confirm.
>Backup.
#LX400051; r. 1.0/23100/23101; en-US
31
Page 42
Backup15
15.2 Backing up Video
1. Insert a USB thumb drive (not included) into one of the USB ports.
2. From live view, right-click and then select Main Menu. Login if prompted.
3. Click
>Backup.
4. Configure your search options:
• Select the USB device you would like to format under Device Name.
• Type: Select the recording type you would like to search for or select All to search
all recording types.
• Channel: Select the channel you would like to search or select All to search all
channels.
• File Format: Select DAV to save files to save files to .dav format. You can playback .
dav files using the FLIR video player software from www.flirsecurity.com/pro. Or, se-
lect ASF for .asf format. You can playback .asf files in VLC Media Player (free download from www.videolan.org) on PC or Mac.
NOTE
VLC Media Player is a free software available from www.videolan.org. VLC Media Player is not
supported by FLIR.
• Start Time/End Time: Select the start and end time for your search.
5. Click Add. A list of files that match your search criteria appears.
6. Check files you would like to backup and then click Backup. Wait for the backup to
complete.
NOTE
HD video files saved on the system may take up a large amount of disk space. The size of video files
selected and the amount of free space on your USB device is shown at the top of the screen.
15.3 Using Video Clip Backup
Video clip backup allows you to select a duration of video during playback mode and save
it to a USB device (not included).
To use Video Clip Backup:
1. Insert a USB flash drive (not included) or USB external hard drive (not included) into
one of the USB ports.
#LX400051; r. 1.0/23100/23101; en-US
32
Page 43
Backup15
2. Start playing back video using the steps in 14.1 Playing Back Video from the Hard
Drive, page 28.
3. Click
to mark the beginning of the video clip. Click to mark the end of the
video clip.
4. Click
to open the Backup menu.
5. Configure the following:
5.1. Check the USB device where you would like to save the file.
5.2. Check the files you would like to backup.
5.3. Click Backup . Then click Start. Wait for the backup to complete before remov-
ing the USB flash drive.
15.4 Viewing Backup Files
To playback .dav backup video files, a Player is available for PC and Mac at
www.flirsecurity.com/pro.
15.4.1 Viewing Backup Files on PC
You can download Video Player for PC from www.flirsecurity.com/pro.
To view backup video files using the Player on PC:
1. Download and install the Video Player for PC from www.flirsecurity.com/pro.
#LX400051; r. 1.0/23100/23101; en-US
33
Page 44
Backup15
2. Double click one of the files on the left to begin playback.
OR
Click
to open a back up video file in another location.
3. Use the Player controls to control playback or select other files for playback.
Video Player Controls
1. File List: Double-click to open a file.
#LX400051; r. 1.0/23100/23101; en-US
34
Page 45
Backup15
2. Display Area: Select the split-screen mode. Double-click a video file to expand. Click
the controls inside the display area to do the following:
•
: View information about the video file.
•
: Start/stop a manual recording from the video file.
•
: Take a snapshot from the video file.
•
: Close the video file.
3. Hide/show file list.
4. Playback controls:
•
: Playback files in sequence.
•
: Synchronize playback times.
: Play/pause playback.
•
•
: Stop playback.
•
: Previous frame.
: Next frame.
•
•
•
: Volume control.
: Playback speed.
5. Zoom Timeline.
6. Add Files: Click to open back up video files.
7. Digital Zoom: Click to activate digital zoom mode. Click and drag in the video to zoom
in. Right-click to unzoom.
8. Drag: When digital zoom is activated, click to activate drag mode. Then click and drag
in the video to view different areas of the image.
9. Full-screen: Click to open the player in full screen. Press ESC to exit full screen.
#LX400051; r. 1.0/23100/23101; en-US
35
Page 46
Backup15
10. Config: Click to open the configuration menu for the player. From here you can control
the default file formats and save locations for snapshots and video files saved from the
player.
15.4.2 Viewing Backup Files on Mac
A Video Player for Mac is available from www.flirsecurity.com/pro.
To view backup video files using the Player on Mac:
1. Download Video Player for Mac from www.flirsecurity.com/pro.
2. Double click the downloaded file in Safari to extract the Smart Player app file.
3. Drag the Smart Player app to your Desktop or Applications list. Double click Smart
Player (
) to open it.
#LX400051; r. 1.0/23100/23101; en-US
36
Page 47
Backup15
4. Double click one of the files on the left to begin playback.
OR
Click
to open a back up video file in another location.
5. Use the Player controls to control playback or select other files for playback.
Video Player Controls
1. File List: Double-click to open a file.
#LX400051; r. 1.0/23100/23101; en-US
37
Page 48
Backup15
2. Display Area: Select the split-screen mode. Double-click a video file to expand. Click
the controls inside the display area to do the following:
•
: View information about the video file.
•
: Take a snapshot from the video file.
•
: Close the video file.
3. Hide/show file list.
4. Playback controls:
•
: When a video file ends, this button lets you select if you want the video player
to repeat the same file or play the next file.
: Play/pause playback.
•
•
: Stop playback.
•
: Previous file.
•
: Next file.
•
•
: Volume control.
: Playback speed.
5. Zoom Timeline.
6. Add Files: Click to open back up video files.
7. Full-screen: Click to open the player in full screen. Press ESC to exit full screen.
8. Config: Click to open the configuration menu for the player. From here you can control
the default file formats and save locations for snapshots and control the aspect ratio.
9. About: Click to see version information for the Player software.
#LX400051; r. 1.0/23100/23101; en-US
38
Page 49
16
Managing Passwords and User Accounts
By default, the system user name is admin and the password is 000000. Passwords are
enabled by default and are required to access the Main Menu or connect to the system using a computer or mobile device. You will be prompted to create a custom password after
you connect for the first time.
NOTE
If you forget the password to the system, contact technical support to have it reset.
The system includes the following default accounts:
• admin: The admin account has full access to the system, may configure all system set-
tings, and can manage user accounts.
• default: The default account is a limited user account that may only view live video from
the cameras.
For security reasons, it is essential that you change the password on your system. By de-
fault, the system password is enabled.
16.1 Changing Passwords
You can change the system password of the admin and user accounts from the Users
menu.
To modify an account password:
1. From Live View, right-click and then select Main Menu.
2. If prompted, enter the system user name (default: admin) and password (default:
000000).
3. Click
4. Click
5. Check Modify Password.
6. Under Old Password, enter the account’s previous password.
7. Under New Password, enter a new 6 character password for the account. Repeat the
new password under Confirm Password.
8. Click OK to save changes.
and select Setting. Select Account.
next to the user account you would like to modify.
#LX400051; r. 1.0/23100/23101; en-US
39
Page 50
Managing Passwords and User Accounts16
16.2 Adding Users
You can allow multiple users to log in to the system. When adding different users, you can
assign what menus they have access to. For example, you may want your friend to monitor
your system while you are away, while not giving full access to your system.
To add a user account:
1. From Live View, right-click and then select Main Menu.
2. If prompted, enter the system user name (default: admin) and password (default:
000000).
3. Click
and select Setting. Select Account.
4. Click Add User.
5. Configure the following:
• User Name: Enter a name for the user account.
• Password: Enter a 6 character password for the user account. Enter the password
again under Confirm Password.
• Memo (optional): Enter a description of the user account.
• Group: Select the group you would like to assign to this user account. A user ac-
count cannot be given permissions its group does not have.
• Multiuser: Check to enable this user account to be used to login from more than
one device at the same time.
• Authority: Check the permissions you would like the user account to have. Under
the System tab, select the menus the user account may access. Under the Play-
back tab, select which channels the user account may access recorded video from.
Under the Covert tab, select the channels the user account may view live video
from.
• User MAC: Not supported. Leave this field blank.
6. Click OK to save changes.
Now, you can log in to the system locally, or remotely using the user name and password
you created. When logging into the system with a user account, the user will only have access to the menus you assigned.
16.3 Modifying Users
1. In the Account menu, click
next to the user account you would like to modify.
2. Update the user’s account details as needed, and then click OK to save changes.
#LX400051; r. 1.0/23100/23101; en-US
40
Page 51
Managing Passwords and User Accounts16
16.4 Deleting Users
1. In the Account menu, click
next to the user account you would like to delete.
2. Click OK to confirm.
NOTE
The admin and default user accounts cannot be deleted from the system.
16.5 Account Groups
Account groups can be used to easily manage permissions for multiple user accounts.
User accounts can be given all the permissions of a group, but cannot be given permissions that the group does not have.
The system includes the following groups by default:
• admin: Accounts in the admin group are system administrators. They have full access
to the system, may configure all system settings, and can manage user accounts.
• user: Accounts in the user group are normal users. They have limited access to system
menus.
16.6 Adding Groups
1. From Live View, right-click and then select Main Menu.
2. If prompted, enter the system user name (default: admin) and password (default:
000000).
3. Click
and select Setting.
4. Click Account and select the Group tab.
5. Click Add Group.
#LX400051; r. 1.0/23100/23101; en-US
41
Page 52
Managing Passwords and User Accounts16
6. Configure the following:
• Under Group Name, enter a name for the group.
• Under Memo, enter an optional comment for this group.
• Under Authority, check the permissions that the group will have. Users accounts
assigned to this group can not be given any permissions the group does not have.
7. Click OK to save changes.
16.7 Modifying Groups
1. In the Group tab, click
next to the group you would like to modify.
2. Update the group’s details as needed, and then click OK to save changes.
16.8 Deleting Groups
1. In the Account menu, click
next to the user account you would like to delete.
2. Click OK to confirm.
NOTE
The admin and user groups cannot be deleted from the system.
#LX400051; r. 1.0/23100/23101; en-US
42
Page 53
17
Using the Main Menu
To open the Main Menu:
• Using the Mouse: Right-click and click Main Menu.
NOTE
The system password may be required to access the Main Menu. By default the user name is admin
and the password is 000000.
1. SEARCH: Open Search/Playback mode. For details, see 14 Search (Playback), page
28.
2. BACKUP: Export files to USB device. For details, see 15 Backup, page 31.
3. CAMERA: Configure image settings, recording parameters, and titles for your
cameras.
4. INFO: View system information.
5. SETTING: Configure general system, schedule, network, recording, display, and motion settings. Restore system to factory defaults.
6. SHUTDOWN: Logout, restart, or shutdown the system.
17.1 Camera
The Camera menu allows you to configure image settings, recording parameters, and titles for your cameras.
NOTE
To change the image settings for your cameras, see 11.3 Adjusting Color Settings, page 21.
17.1.1 Recording
The Recording menu allows you to set recording parameters for your cameras, such as
the resolution and frame rate.
#LX400051; r. 1.0/23100/23101; en-US
43
Page 54
Using the Main Menu17
17.1.2 Configuring Recording Quality
The system employs two video recording streams, a Main Stream and a Sub Stream. The
Main Stream records high quality video to your system’s hard drive. The Sub Stream records lower resolution video for efficient streaming to devices over the Internet. You can
customize the video quality settings for these streams according to your needs.
To configure recording quality:
1. From the Main Menu, click
and select Recording>Recording.
2. Select the camera you would like to configure.
3. Configure the following settings. Settings for the Main Stream are in the left column.
Settings for the Sub Stream are in the right column.
• Type: For the Main Stream, you can set different recording quality settings for Con-
tinuous, MD (Motion Detect), and Alarm recording. Select the type of recording you
would like to configure.
• Resolution: Select the resolution the selected camera will be recorded at. Higher
resolutions create a more detailed image, but take up more hard drive space to record and require more bandwidth to stream to connected computers or mobile
devices.
• Available resolutions for the Main Stream are: 1080P (1920x1080), 720P
(1280x720), 960H (960x480 NTSC / 960x576 PAL), D1 (704x480 NTSC /
704x576 PAL), 2CIF (704x240 NSTC / 704x288 PAL), HD1 (352x480 NTSC /
352x576 PAL), and CIF (352x240 NTSC / 352 × 288 PAL).
• Available resolutions for the Sub Stream are: D1 (704x480 NTSC / 704x576
PAL), CIF (352x240 NTSC / 352 × 288 PAL), and QCIF (176x120 NTSC /
176x144 PAL).
• Frame Rate (FPS): Select the frame rate in Frames Per Second (FPS) that each
stream will record at. A higher frame rate provides a smoother picture, but requires
more storage and bandwidth.
• Bit Rate Type: Select CBR (Constant Bit Rate) or VBR (Variable Bit Rate) to deter-
mine the bit rate type. If you select VBR, you can set the video quality setting between 1 and 6. If you select VBR, select the Quality from 1 (lowest) to 6 (highest).
• Bit Rate (Kbps): Select the bit rate for each recording stream. A higher bit rate results in a better image, but increases the amount of hard drive space or bandwidth
required.
4. (Optional) Click the Copy button to copy recording settings to other channels.
5. Click OK to save changes.
#LX400051; r. 1.0/23100/23101; en-US
44
Page 55
Using the Main Menu17
17.1.3 Configuring Audio Recording
The system supports one channel of audio recording.
NOTE
You must connect an RCA audio input device to the system to use audio recording or you must have an
MPX camera that supports audio.
To configure audio recording:
1. From the Main Menu, click
and select Recording>Recording.
2. Under Channel, select 1.
3. Check the left Audio/Video checkbox to enable audio recording. Check the middle
checkbox to enable audio streaming to remote devices (such as a smartphone). Check
the right checkbox to enable video streaming to remote devices.
4. Under Audio Format, select the format that will be used to record audio. G711a is
recommended.
5. Under Audio Source, select Normal to use the system’s RCA audio input.
6. Click OK to save changes.
17.1.4 Configuring Snapshot Recording Settings
The system can be set to record snapshot images when a camera detects motion. These
snapshots can be viewed through the Search menu or can be attached to email alerts and
push notifications. The Snapshot tab in the Recording menu controls the quality and recording parameters for each camera.
NOTE
In order to enable Snapshot recording, the following menu options must be configured:
• The Snapshot schedule must be enabled for times that you would like to save snapshots. See 17.3.16
Configuring the Snapshot Schedule, page 64.
• Snapshot recording must be enabled for motion detection in the Event menu. See 17.3.7 Configuring
Motion Detection, page 56.
To configure snapshot recording settings:
1. From the Main Menu, click
and select Recording>Snapshot.
2. Under Snap Number, select the number of snapshots the system will take when the
snapshot button is pressed.
#LX400051; r. 1.0/23100/23101; en-US
45
Page 56
Using the Main Menu17
3. Configure the following settings for snapshots saved automatically from motion detection or the snapshot schedule:
• Channel: Select the channel you would like to configure.
• Mode: Select Timing for the system to take snapshots according to the snapshot
schedule (see 17.3.16 Configuring the Snapshot Schedule, page 64) Select Trig-
ger for the system to take snapshots only when triggered by motion detection
(snapshot must be enabled in the Motion Detect menu (see 17.3.7 Configuring Mo-
tion Detection, page 56).
• Image Size: Select the resolution for snapshots.
• Image Quality: Select the snapshot image quality between 1 (lowest) and 6
(highest)
• Snapshot Frequency: Select the number of snapshots (up to 6) the system will
take each time.
4. Click OK to save changes.
17.1.5 Creating Custom Channel Names
You can assign custom names to your cameras. For example, you can name your cameras
based on their location (e.g. hallway or front door).
To create custom channel names:
1. From the Main Menu, click
and select Channel Name.
2. Enter a custom name for each channel.
3. Click OK to save changes.
#LX400051; r. 1.0/23100/23101; en-US
46
Page 57
Using the Main Menu17
17.1.6 Selecting Cable Type
The Cable Type menu is used only if you are using cabling with a resistance higher than
10Ω per 100m (330ft) and you are having picture quality issues. Select the UTP option for
any channels having the issue. In all other installations, use the Coaxial setting. Click OK
to save your changes.
#LX400051; r. 1.0/23100/23101; en-US
47
Page 58
Using the Main Menu17
17.2 Info
Info contains menus that show you system information.
17.2.1 HDD Info
The HDD Info sub-menu shows information related to the hard drives installed in the system, including capacity, status, and type.
To access the HDD Info menu:
• From the Main Menu, click
and then click Info.
17.2.2 Record Info
#LX400051; r. 1.0/23100/23101; en-US
48
Page 59
Using the Main Menu17
The Record Info menu shows the start and end times of recordings saved on the hard
drive.
To access the Record Info menu:
• From the Main Menu, click
and then select Info>Record Info.
17.2.3 Version
The Version sub-menu allows you to view information about the current firmware installed
on the system.
To access the Version menu:
• From the Main Menu, click
and then click Info>Version.
17.2.4 Alarm Status
The Alarm Status menu shows you a display of system alarms. Activated alarms are highlighted in white. Additional info such as channels that are currently detecting motion is
shown.
The following alarms are shown in the Alarm Status menu:
• No HDD: No hard drive is detected.
• Disk Error: Hard drive error detected.
• Disk Full: Hard drive is full.
• Net Disconnection: System is not connected to the network.
• IP Conflict: More than one device on the network is using the same IP address.
• MAC Conflict: More than one device on the network is using the same MAC address.
• Local Alarm: Not supported.
• Net Alarm: Not supported.
#LX400051; r. 1.0/23100/23101; en-US
49
Page 60
Using the Main Menu17
• Video Loss: Shows disconnected channels.
• Motion: Shows channels with active motion alarms.
To access the Alarm Status menu:
• From the Main Menu, click
and then select Alarm Status.
17.2.5 Online Users
The Online Users menu shows a list of users connected to the system using computers or
mobile devices.
To access Online Users:
• From the Main Menu, click and then select Network.
17.2.6 Load
The Load menu shows you the network traffic your system is sending and receiving.
To access Load:
• From the Main Menu, click
#LX400051; r. 1.0/23100/23101; en-US
and then select Network>Load.
50
Page 61
Using the Main Menu17
17.2.7 Test
The Test menu allows you to test if your system can connect to other devices over the LAN
or Internet. You can enter the IP address of a device and click Test to determine if your
system can connect to it.
To access Test:
• From the Main Menu, click
and then select Network>Test.
17.2.8 BPS
The BPS sub-menu shows the bitrates of connected cameras. The bitrate is the amount of
data the camera is sending to the system.
To access BPS:
• From the Main Menu, click
and then select BPS.
17.2.9 Log
The Log sub-menu allows you to search for system logs.
#LX400051; r. 1.0/23100/23101; en-US
51
Page 62
Using the Main Menu17
To search for system logs:
1. From the Main Menu, click
and then select Log.
2. Under Type, select the log type to search for.
3. Under Start Time and End Time, select the start and end time for your search.
4. Click Search.
5. (Optional) Click Backup to export logs to a USB flash drive connected to the system.
#LX400051; r. 1.0/23100/23101; en-US
52
Page 63
Using the Main Menu17
17.3 Setting
The Setting menu allows you to configure general system, schedule, network, recording,
display, and motion settings. It also allows you to restore the system to factory defaults.
17.3.1 Network
The Network menu allows you to configure network parameters for your system.
17.3.2 Selecting DHCP or Static IP Address (TCP/IP)
The TCP/IP menu allows you to configure IP address settings.
To configure IP address settings:
1. From the Main Menu, click
and then select Network>TCP/IP.
2. Check DHCP (recommended) to let the system automatically obtain an IP address
from the router or uncheck to assign a static IP address.
If you uncheck DHCP, configure the following:
• IP Address: Enter the IP address you would like to assign to the system. Make sure
that no other device on your network is using the same IP address.
• Subnet Mask: Enter the subnet mask for your network.
• Default Gateway: Enter the gateway address for your network.
• Preferred DNS: Enter the address of your primary DNS server.
• Alternate DNS: Enter the address of your secondary DNS server.
3. Click OK to save changes.
#LX400051; r. 1.0/23100/23101; en-US
53
Page 64
Using the Main Menu17
17.3.3 Configuring System Ports (Connection)
The Connection menu allows you to configure ports used by the system. Please note that
port forwarding is not required to use FLIR Cloud™ or to connect using the apps.
If you are using DDNS connectivity, port forwarding is required for the HTTP Port (defaut:
80) and TCP (Client Port) (default: 35000).
To configure system ports:
1. From the Main Menu, click
and then select Network>Connection.
2. Configure the ports as needed and click OK to save changes.
NOTE
Up to 3 devices may connect to the system at the same time when using FLIR Cloud™.
17.3.4 Configuring DDNS Settings
FLIR DDNS is available as an optional connectivity option. Please see 21 DDNS Setup
(Advanced), page 148 for details.
The primary connectivity option uses FLIR Cloud™ to connect to your system over the Internet without requiring port forwarding or DDNS registration. For details, see 18 Connect-
ing to Your System Over the Internet on PC or Mac, page 76.
To configure DDNS Settings:
1. Visit http://ddns.myddns-flir.com and register for a DDNS account.
2. From the Main Menu, click
#LX400051; r. 1.0/23100/23101; en-US
and then select Network>DDNS.
54
Page 65
Using the Main Menu17
3. Check Enable.
4. Under Domain Name, enter the Domain Name/URL Request your received in the
email after registering for DDNS.
5. Under User ID, enter your DDNS User Name.
6. Under Password, enter your DDNS Device password.
7. Click OK to save your settings.
NOTE
Please allow 10~15 minutes for the DDNS servers to update with your new DDNS address before attempting to connect.
17.3.5 Configuring Email Alerts
You can configure the system to send out email alerts for motion detection or other events.
NOTE
To send out motion detection alerts, you must enable the Send Email option for motion detection on each
camera you would to receive alerts from. For details, see 17.3.7 Configuring Motion Detection, page 56.
NOTE
SMTP server connection information is required to set up email alerts. Contact your email service provider to retrieve your SMTP server information.
To configure Email Alerts:
1. From the Main Menu, click
and then select Network>Email.
2. Check Enable to enable email notifications.
#LX400051; r. 1.0/23100/23101; en-US
55
Page 66
Using the Main Menu17
3. Configure the following:
• SMTP Server: Enter the SMTP server address.
• Port: Enter the port used by the SMTP server.
• Anonymous: Check if your server supports anonymous log ins. Otherwise, leave
this unchecked.
• User Name: Enter the SMTP user name.
• Password: Enter the SMTP password.
• Receiver: Enter the email address that will receive alerts.
• Sender: Enter the sender’s email address.
• Subject: Enter the subject line for the email alert.
• Attachment: Check to include a jpg image attachment of the camera.
NOTE
You must enable the Snapshot option for motion detection on each camera you would to receive
attachments. For details, see 17.3.7 Configuring Motion Detection, page 56.
• Encrypt Type: Select SSL or TLS if your server uses encryption. Select None if
your server does not use encryption.
• Event Interval: Enter the interval between alert emails.
• Health Enable: Check to enable health check emails. Health check emails will be
sent periodically to ensure that the system is functioning normally.
• Interval: Enter the interval in minutes for health check emails.
4. Click Test to send a test email.
5. Click OK to save settings.
17.3.6 Event
The Event menu allows you to configure settings for motion detection, video loss, and system warnings.
17.3.7 Configuring Motion Detection
Motion Detection events allow the system to mark footage that has motion. This allows
you to quickly locate relevant footage through Search. You can also configure system responses to motion detection events, such as activating the system buzzer or sending an
email alert.
To configure Motion Detection events:
1. From the Main Menu, click and then click Event>Motion>Motion Detect.
2. Under Channel, select the channel you would like to configure.
3. Check Enable to enable motion detection on the selected channel.
#LX400051; r. 1.0/23100/23101; en-US
56
Page 67
Using the Main Menu17
4. Click Setup next to Region to configure which areas of the image will be enabled for
motion detection. A grid will appear over the camera’s live view.
Motion Grid
• Areas enabled for motion detection are shown in color and areas that are disabled
are transparent.
• Hover the mouse at the top of the screen to select which motion area you would like
to configure. You can set up to 4 motion detection areas and customize the sensitivity and threshold for motion detection separately for each area between 0 (lowest)
and 100 (highest).
• The Sensitivity determines how sensitive the camera is to motion. For example, if
the sensitivity is high, small amounts of motion are more likely to trigger an event. It
is recommended to select a Sensitivity between 30~70.
• The Threshold determines how much motion is required to trigger an event. If the
amount of motion exceeds the threshold, an event occurs. It is recommended to select a Threshold between 10~50.
• Right-click when finished.
NOTE
It is recommended to have a second person walk in front of the camera to test different Sensitivity
and Threshold settings to determine the best setting for your camera’s location.
5. Under Anti-dither, enter the anti-dither time. After a motion event occurs and motion
stops, if motion is detected within the anti-dither time, the system continues the motion
event and includes the new motion within the first event, rather than creating a new
motion event.
6. Under Post_REC, enter the time the system will record after a motion event occurs.
7. To configure a schedule when motion detection will be enabled on this channel, click
Setup next to Period. Configure times when motion detection will be enabled. For example, you may want to disable motion detection during business hours and enable it
outside of business hours. Click OK when finished.
NOTE
This setting can override scheduled motion recording. This means that motion recording will only
take place at times that are enabled both in the Schedule menu and here.
#LX400051; r. 1.0/23100/23101; en-US
57
Page 68
Using the Main Menu17
8. Configure the following system actions when motion is detected:
• Alarm Out: Check the box to activate alarm output devices (not included) that will
trigger when the selected channel detects motion. Select the alarm output devices
that will be activated when motion is detected.
• Latch: Enter the number of seconds an alarm output device will activate after mo-
tion is detected.
• Show Message: Check to enable an on-screen pop-up when one of your cameras
detects motion. On-screen pop-up shows the channels an event occurred on and
the type of event.
• Alarm Upload: Check to enable the system to upload alerts to FLIR Cloud™ Client.
• Send Email: Check to enable email alerts. You must configure email alerts before
you will be able to receive them (see 17.3.5 Configuring Email Alerts, page 55).
• Recording Channel: Select the channels that will record when motion is detected
on the selected channel.
• PTZ Activation: Check to enable PTZ actions when motion is detected (PTZ cam-
era required; not included). Click Setup to select which PTZ actions will be taken by
each camera.
• Buzzer: Check to enable the system buzzer.
• Sequence: Check to enable a custom sequence mode when motion is detected on
the selected channel. Then click the channels you would like to display in the custom sequence mode.
• Snapshot: Check to save a snapshot when the camera detects motion.
9. Click OK to save changes.
17.3.8 Configuring Video Loss Settings
Video Loss occurs if the system loses connection to one of the cameras.
To configure Video Loss settings:
1. From the Main Menu, click
and then click Event>Motion>Video Loss.
2. Under Channel, select the channel you would like to configure.
3. Check Enable to enable video loss events for the selected channel.
#LX400051; r. 1.0/23100/23101; en-US
58
Page 69
Using the Main Menu17
4. Configure the following to customize settings for video loss events:
• Period: Click Setup to configure a schedule for video loss events. It is recom-
mended to leave this on the default setting, so you can be alerted at any time one of
your cameras loses video.
• Alarm Out: Select the alarm output devices (not included) that will trigger when vid-
eo loss occurs.
• Latch: Enter the number of seconds an alarm output device will activate after video
loss occurs.
• Show Message: Check to show a popup message on the monitor if one of your
cameras loses video.
• Alarm Upload: Check to enable the system to upload alerts to FLIR Cloud™ Client.
• Send Email: Check to enable email alerts. You must configure email alerts before
you will be able to receive them (see 17.3.5 Configuring Email Alerts, page 55).
• Record Channel: Click the checkbox to enable video recording when video loss
occurs. You can then select the channels the system will record when video loss occurs on the currently selected channel.
• PTZ Activation: Check to enable PTZ actions when video loss occurs (PTZ camera
required; not included). Click Setup to select which PTZ actions will be taken by
each camera.
• Post_REC: Enter the number of seconds the system will record after video loss
occurs.
• Snapshot: Click the box to enable snapshot recording when video loss occurs. You
can then select which channels will save snapshots when video loss occurs on the
currently selected channel.
• Sequence: Check to enable a custom sequence mode when video loss occurs on
the selected channel. Then click the channels you would like to display in the custom sequence mode.
• Buzzer: Check to enable the system buzzer when video loss occurs on the cur-
rently selected channel.
5. Click OK to save changes.
17.3.9 Configuring Alarm Input Devices
You can connect alarm input devices such as motion sensors (not included) or glass break
detectors (not included) to the system. The system can be set to trigger recording or take
other actions when these devices are activated.
To configure alarm input devices (not included):
1. From the Main Menu, click
#LX400051; r. 1.0/23100/23101; en-US
and then click Event>Alarm.
59
Page 70
Using the Main Menu17
2. Configure the following to activate an alarm input device:
• Alarm In: Select the alarm input port the device is connected to.
• Enable: Check to enable the alarm input device connected to the selected port.
• Type: Select Normal Open or Normal Close depending on the type of alarm input
device you have.
3. Configure the following system responses and parameters for the alarm input device:
• Period: Click Setup to configure the times of the week when the selected device
will be activated. By default, the device will be activated 24/7.
• Anti-dither: Enter the anti-dither time. After the device triggers, if it triggers again
within the anti-dither time, the system continues the event and includes the second
activation within the first event, rather than creating a new event.
• Alarm Out: Check the box to activate alarm output devices (not included) and se-
lect the alarm output devices (not included) will be activated when the selected device is triggered.
• Latch: Enter the number of seconds an alarm output device will activate after the
selected device is triggered.
• Show Message: Check to enable an on-screen pop-up when the selected device
is triggered.
• Alarm Upload: Check to enable the system to upload alerts to FLIR Cloud™ Client.
• Send Email: Check to enable email alerts. You must configure email alerts before
you will be able to receive them (see 17.3.5 Configuring Email Alerts, page 55).
• Record Channel: Select the channels that will record when the selected device is
triggered.
• PTZ Activation: Check to enable PTZ actions when the selected device is triggered
(PTZ camera required; not included). Click Setup to select which PTZ actions will
be taken by each camera.
• Sequence: Check to enable a custom sequence mode when the alarm device trig-
gers. Then click the channels you would like to display in the custom sequence
mode.
• Buzzer: Check to enable the system buzzer.
• Snapshot: Check to save a snapshot.
4. Click OK to save changes.
17.3.10 Controlling Alarm Output Devices
You can connect alarm output devices (not included), such as sirens or strobe lights, to
the system. The Alarm Output menu allows you to enable or disable alarm output devices
and manually activate a device.
#LX400051; r. 1.0/23100/23101; en-US
60
Page 71
Using the Main Menu17
To access the Alarm Output menu:
1. From the Main Menu, click
and then click Event>Alarm Output.
To control alarm output devices:
• To enable alarm output devices, select Schedule or Manual for each device you would
like to enable. Select Stop to disable the alarm output device. Click OK to save
changes.
• To manually disable activated alarm devices, click OK under Alarm Release.
17.3.11 Configuring Hard Drive Warnings
Hard drive warnings will notify you if an issue is detected with the hard drive.
To configure hard drive warnings:
1. From the Main Menu, click
and then click Event>Warning>HDD.
2. Under Event Type, select the hard drive event you would like to configure.
• No Disk: No hard drive detected.
• Disk Error: A hard drive error has been detected.
• Disk Full: The hard drive is full or almost full. You can enter the percentage of disk
space remaining that will trigger a warning under Less Than (e.g. when less than
10% of the hard drive is empty, trigger a warning). Disk Full warnings will not occur if
overwrite is enabled.
• All: Configure warnings for all hard drive events.
#LX400051; r. 1.0/23100/23101; en-US
61
Page 72
Using the Main Menu17
3. Configure the responses the system will take when the selected event occurs:
• Alarm Out: Activate selected alarm out devices. Use Latch to select the number of
seconds the alarm out device will be activated.
• Show Message: Show a popup message on the monitor.
• Alarm Upload: Check to enable the system to upload alerts to FLIR Cloud™ Client.
• Send Email: Check to enable email alerts. You must configure email alerts before
you will be able to receive them (see 17.3.5 Configuring Email Alerts, page 55).
• Buzzer: Check to activate the system buzzer.
4. Click OK to save changes.
17.3.12 Configuring Network Warnings
Network warnings will notify you if your system loses connection to the Internet or local
network or if there is an issue on your network.
To configure network warnings:
1. From the Main Menu, click
and then click Event>Warning>Network.
2. Under Event Type, select the event type you would like to configure.
• Net Disconnection: The system has lost connection to the network.
• IP Conflict: More than one device on your network has the same IP address.
• MAC Conflict: More than one device on your network has the same MAC address.
• All: Configure responses for all network events.
3. Configure the following for the selected event type:
• Alarm Out: Activate selected alarm out devices. Use Latch to select the number of
seconds the alarm out device will be activated.
• Enable: Check to enable the selected event type.
• Show Message: Check to show a popup message when the selected event occurs.
• Send Email: Check to enable email alerts. You must configure email alerts before
you will be able to receive them (see 17.3.5 Configuring Email Alerts, page 55).
• Buzzer: Check to activate the system buzzer.
4. Click OK to save changes.
17.3.13 Storage
The Storage menu allows you to configure the recording schedule and hard drives connected to the system.
#LX400051; r. 1.0/23100/23101; en-US
62
Page 73
Using the Main Menu17
17.3.14 Configuring the Video Recording Schedule
You can set a custom recording schedule according to your needs. For example, you can
set the system to record continuously during business hours and record on motion detection only outside of business hours.
A custom recording schedule helps reduce the amount of hard drive space required, increasing the time your system can retain recordings.
To configure the video recording schedule:
1. From the Main Menu, click
and then click Storage>Schedule>Record.
2. Under Channel, select the channel you would like to configure or select All.
3. Configure the schedule as needed:
• Check Continuous, MD (motion detection), Alarm, or Alarm & MD to select the re-
cording type you would like to configure.
• Click and drag on each day to customize the recording schedule. The schedule is
set up as a grid, which each block representing one hour.
• Click
changes to
next to All to link the recording schedules for all days. The icon for a day
when days are linked. You can also click the boxes next to individual days to link them to each other. If the recording schedule is linked, changes
made to one of the days will apply to every day that is linked.
• Click
• Click
to disable all recording of the selected type on the selected day.
if you need to set a more precise schedule down to the minute.
4. Click OK to save changes.
17.3.15 Configuring Pre-Recording
The system can pre-record video when motion detection events occur.
#LX400051; r. 1.0/23100/23101; en-US
63
Page 74
Using the Main Menu17
To configure pre-recording:
1. From the Main Menu, click
and then click Storage>Schedule>Record.
2. Under Channel, select the camera you would like to configure or select All.
3. Under PreRecord, select the duration for pre-recording.
4. Click OK to save settings.
17.3.16 Configuring the Snapshot Schedule
You can set a schedule for recording snapshots from the cameras.
To set up the snapshot schedule:
1. From the Main Menu, click
and then click Storage>Schedule>Snapshot.
2. Under Channel, select the channel you would like to configure or select All.
#LX400051; r. 1.0/23100/23101; en-US
64
Page 75
Using the Main Menu17
3. Configure the schedule as needed:
• Check Continuous, MD (motion detection), Alarm, or Alarm & MD to select the recording type you would like to configure.
• Click and drag on each day to customize the recording schedule. The schedule is
set up as a grid, which each block representing one hour.
• Click
changes to
next to All to link the recording schedules for all days. The icon for a day
when it is linked. You can also click the boxes next to individual
days to link them to each other. If the recording schedule is linked, changes made
to one of the days will apply to every day that is linked.
• Click
• Click
to disable all recording of the selected type on the selected day.
if you need to set a more precise schedule down to the minute.
4. Click OK to save changes.
17.3.17 Configuring Holidays
You can set certain days as holidays. Holidays have a special recording schedule.
To configure holidays:
1. From the Main Menu, click
and then click Setting>General>Holiday.
2. Click Add New Holidays.
#LX400051; r. 1.0/23100/23101; en-US
65
Page 76
Using the Main Menu17
3. Configure the following:
• Holiday Name: Enter a name for this holiday.
• Repeat Mode: Select Once Only for the holiday to occur only this year or All-Year
for the holiday to be repeated each year.
• Holiday Range: Select Date to select a specific date, or select Week to select holidays based on which week they fall on.
4. Click Add. Now that you have added a holiday, an extra holiday setting is added to the
recording schedule.
NOTE
You cannot delete holidays, but you can disable them by selecting Stop under the Status drop-down
and then click Apply.
17.3.18 Formatting the Hard Drive
The HDD Manager menu allows you to format the hard drive. If you install a new hard
drive, you must format the hard drive using the system before you will be able to record.
To format the hard drive:
CAUTION
Formatting the hard drive erases all data on the hard drive. This step cannot be undone.
1. From the Main Menu, click and then click Storage>HDD Manager.
2. Select the hard dive you would like to format and then click Format. Click OK to
confirm.
#LX400051; r. 1.0/23100/23101; en-US
66
Page 77
Using the Main Menu17
3. Click OK to save changes. The system will restart to complete the formatting process.
17.3.19 Configuring Hard Drive Type
The system supports the following hard drive types:
• Read-write HDD: Normal recording hard drive.
• Read-only HDD: The system can playback data from this hard drive, but it will not re-
cord to it.
• Mirroring HDD: The hard drive will be used for mirror recording only. You must set up
mirroring recording before this feature will work.
To set the hard drive type:
1. From the Main Menu, click
and then click Storage>HDD Manager.
2. Click the hard drive you would like to configure.
3. Under Type, select Read-write HDD, Read-only HDD, or Mirroring HDD.
4. Click OK to save changes. The system will restart to complete this operation.
17.3.20 Setting up Hard Drive Mirroring (Advanced)
A mirror hard drive can be used to automatically backup video footage recorded to the recording (read-write) hard drive. When a mirroring hard drive is installed, the system can be
set to record cameras in parallel to both the recording hard drive and the mirror hard drive.
This way, the footage is automatically backed up if the recording hard drive fails.
How hard drive mirroring works:
1. Security system.
2. Primary hard drive.
3. Mirror hard drive.
#LX400051; r. 1.0/23100/23101; en-US
67
Page 78
Using the Main Menu17
NOTE
• The mirror hard drive must be as large or larger than primary hard drive to backup all recordings.
• HDD mirroring begins from when mirror hard drive is installed and configured.
• Two hard drives must be installed in the system to use HDD mirroring. For details on installing hard
drives, see 24 M3200 / M4200 SERIES Hard Drive Installation, page 165.
To set up hard drive mirroring:
1. From the Main Menu, click
and then click Storage>HDD Manager.
2. Click the Type drop-down under the second hard drive and select Mirror HDD.
CAUTION
Setting a hard drive for mirroring erases all data on the hard drive. This step cannot be undone.
3. Click OK to apply changes. Click Yes to confirm. The system will format the hard drive
and restart.
4. When the system restarts, click
and then click Storage>Schedule>Record.
5. Under Channel, select the channel you would like to enable for mirror recording, then
check Mirroring. Repeat the process for any additional channels.
6. Click OK to save changes.
17.3.21 Configuring General System Settings
You can use the General menu to configure miscellaneous system settings.
#LX400051; r. 1.0/23100/23101; en-US
68
Page 79
Using the Main Menu17
To configure general settings:
1. From the Main Menu, click
and then click Setting>General>General.
2. Configure the following:
• Device Type: Shows the model number of your system.
• Device No.: Select the remote control address of the system. See 10.1 Setting the
Remote Control Address, page 19.
• Language: Set the system languages. Available options are English, French, and
Spanish.
• Video Standard: Select NTSC (North America) or PAL (Europe).
• HDD Full: Select Overwrite for the system to overwrite the oldest recordings when
the hard drive is full or select Stop Record for the system to stop recording when
the hard drive is full.
• Pack Duration: Select the length (in minutes) of video files stored on the system.
For example, if this is set to 30 minutes, the system will create a new video file for
each 30 minutes of continuous recording.
• Instant Playback: Select the amount of time (in minutes) the system will go back
when instant playback is activated in live view.
• Auto Logout: Select the idle time (in minutes) before the system will logout the cur-
rent user.
• Navigation Bar: Check to enable the Navigation Bar that comes up when you left
click in live view.
• Startup Wizard: Check to enable a setup wizard when you start up the system.
• Mouse Speed: Use the slider to adjust the mouse speed.
3. Click OK to save changes.
17.3.22 Setting the Monitor Resolution (Display)
The Display menu allows you to configure the systems monitor resolution and other display settings.
#LX400051; r. 1.0/23100/23101; en-US
69
Page 80
Using the Main Menu17
To set the monitor resolution:
1. From the Main Menu, click
and then click Setting>Display>Display.
2. Under Resolution, select the correct resolution for your monitor: 1920x1080,
1280x1024, 1280x720, or 1024x768.
3. Click OK to save changes. Click OK again to restart the system using the new
resolution.
To configure other display settings:
1. From the Main Menu, click
and then click Setting>Display>Display.
2. Configure the following:
• Transparency: Select the menu transparency.
• Time Display: Check to show the time on the monitor.
• Channel Display: Check to show the channel names on the monitor.
• Image Enhance: Check for the system to digitally improve the video quality on the
live display. This setting does not affect recordings.
3. Click OK to save changes.
17.3.23 Configuring RS232 for a PTZ Keyboard
You can use the RS232 connector on the system to connect to a FLIR PTZ keyboard (not
included) via RS232.
#LX400051; r. 1.0/23100/23101; en-US
70
Page 81
Using the Main Menu17
NOTE
When configuring your PTZ keyboard, the RS232 address of your system is set under Device No. in the
Main Menu>
>General>General menu.
To configure RS232 settings for a PTZ keyboard:
1. From the Main Menu, click
and then click Setting>RS232.
2. Configure the following:
• Function: Select Netkeyboard.
• Baud Rate: Select a baud rate that is compatible with your PTZ keyboard.
• Data Bits: Select a data bits setting that is compatible with your PTZ keyboard.
• Stop Bits: Select a stop bit setting that is compatible with your PTZ keyboard.
• Parity: Select a parity setting that is compatible with your PTZ keyboard.
3. Click OK to save changes.
17.3.24 Saving Your System Configuration to a USB Thumb Drive
The system allows you to save your current system configuration to a USB thumb drive
(not included). This is useful if you want to backup your current settings.
NOTE
This function only saves settings created in system menus. It does not save or backup any video.
To save your system configuration to a USB thumb drive:
1. Insert a USB thumb drive (not included) into one of the USB ports.
#LX400051; r. 1.0/23100/23101; en-US
71
Page 82
Using the Main Menu17
2. From the Main Menu, click
and then click Setting>Config Backup.
3. Under Device Name, select the USB device where you would like to save the
configuration.
4. Click EXPORT to save your current system configuration.
To restore a saved system configuration:
1. Insert a USB thumb drive (not included) with a saved system configuration into one of
the USB ports.
2. From the Main Menu, click
and then click Setting>Config Backup.
3. Under Device Name, select the USB device.
4. Click the folder with the configuration files you would like to restore. Configuration file
folders are labeled “Config” and then the time and date the configuration was saved (e.
g. Config_20140425103727).
5. Click IMPORT to restore the system configuration.
6. Click OK to confirm. The system will restart to complete the operation.
17.3.25 Setting the System to Factory Defaults
The Default menu allows you to reset the system to factory default settings.
#LX400051; r. 1.0/23100/23101; en-US
72
Page 83
Using the Main Menu17
To reset the system to factory default settings:
1. From the Main Menu, click
and then click Setting>Default.
2. Check the menus you would like to reset to default settings or check Factory Default
to reset the entire system to default settings.
3. Click OK.
17.3.26 Upgrading Firmware from USB
Firmware upgrades provide enhanced functionality. The system will automatically check
for firmware upgrades if it is connected to the Internet. The system also supports firmware
upgrades from a USB thumb drive (not included).
To upgrade firmware from a USB drive:
1. Download the firmware upgrade from www.flirsecurity.com/pro.
2. Extract the firmware file and copy the firmware to a blank USB thumb drive.
NOTE
Do not have any folders on the USB thumb drive—just the firmware file.
3. Insert the USB thumb drive to a USB port on the system.
4. Right-click and then click Main Menu. Click
>Setting>Upgrade.
5. Click Start.
#LX400051; r. 1.0/23100/23101; en-US
73
Page 84
Using the Main Menu17
6. Select the firmware file on the USB drive and click Start.
WARNING
DO NOT POWER OFF THE SYSTEM OR DISCONNECT THE POWER CABLE DURING FIRMWARE INSTALLATION
#LX400051; r. 1.0/23100/23101; en-US
74
Page 85
Using the Main Menu17
17.4 Shutdown
Use the Shutdown menu to shutdown, restart, or log out of the system.
To access the Shutdown menu:
1. From live view, right-click and select Main Menu.
2. Enter the system User Name (default: admin) and Password (default: 000000) and
click OK.
3. Click
>Shutdown.
4. Select one of the following:
• Logout: Log out the account that is currently active.
• Shutdown.
• Restart.
#LX400051; r. 1.0/23100/23101; en-US
75
Page 86
18
Connecting to Your System Over the Internet on PC or Mac
This system features connectivity using the exclusive FLIR Cloud™. This cloud-enabled
service allows for Internet connectivity without requiring any network configuration. Up to 3
devices may connect to the system at the same time.
NOTE
• Except where noted, the PC and Mac instructions in this section are the same.
• For smartphone/tablet setup, see 20 Connecting to your System Using Smartphone or Tablet Apps,
page 107.
• For the latest list of supported apps and devices, visit www.flirsecurity.com/pro.
18.1 System Requirements
Your system must meet the system requirements below:
Description Requirement
CPU Core 2 Duo 3.0GHz
Operating System Windows™ 8/7/Vista
Mac OSX 10.7 and above
Memory
Video 512 MB of video memory and above
Network (LAN) 10/100 BaseT Network
Network (WAN) 1 Mbps upstream
18.2 Step 1 of 3: Connect your System to Your Router
1. Power off your system by disconnecting the power adapter.
2. Connect an Ethernet cable (included) to the LAN port on the rear panel of the system.
Connect the other end of the Ethernet cable to an empty LAN port (usually numbered
1~4) on your router.
2GB
High-speed Internet service is required to remotely
connect to your system.
#LX400051; r. 1.0/23100/23101; en-US
76
Page 87
18
Connecting to Your System Over the Internet on PC or Mac
3. Reconnect the power adapter to power the system back on.
18.3 Step 2 of 3: Obtain the system’s Device ID
The Device ID is a unique code that allows your system to handshake with FLIR Cloud™
servers for a secure connection over the Internet.
To find the Device ID:
1. The Device ID is located on a sticker on the system.
2. Write down the Device ID of the system.
18.4 Step 3 of 3: Connect to the System Over the Internet
Follow the steps below to connect to the system over the Internet.
NOTE
Make sure to upgrade your system to the latest firmware version. You must have the latest firmware
and client software to connect to the system over the Internet.
To connect to the system over the Internet:
1. Download and install the client software.
• PC Users: Download and install the Client Software for PC from
www.flirsecurity.com/pro.
• Mac Users: Download and install the Client Software for Mac from
www.flirsecurity.com/pro. Double click to extract the software. Then, drag the soft-
ware to Applications.
2. Once installation is finished, double-click the FLIR Cloud™ Client icon (
) from the
desktop or Applications list.
#LX400051; r. 1.0/23100/23101; en-US
77
Page 88
18
Connecting to Your System Over the Internet on PC or Mac
3. Log into the Client Software using the Client Software user name (default: admin) and
password (default: admin) and then click Login.
4. Click Add Device.
5. Enter the following:
#LX400051; r. 1.0/23100/23101; en-US
78
Page 89
18
Connecting to Your System Over the Internet on PC or Mac
5.1. Device Name: Choose a name for your system of your choice.
5.2. Device ID: Manually enter the Device ID printed on the label.
5.3. Client Port: Enter the Client Port (default: 35000).
5.4. User Name: Enter the system User Name (default: admin).
5.5. Password: Enter the system Password (default: 000000).
6. Click Add. If this is the first time you are connecting, you will be prompted to change
the system password.
7. Enter a new 6 character password and click OK. This password will be used to connect to your system from now on.
8. Click then .
#LX400051; r. 1.0/23100/23101; en-US
79
Page 90
18
Connecting to Your System Over the Internet on PC or Mac
9. Click and drag Default Group to the display window to open your cameras in live view.
Congratulations! You can now connect over the Internet to view and playback video
on your computer.
#LX400051; r. 1.0/23100/23101; en-US
80
Page 91
19
Using FLIR Cloud™ Client for PC or Mac
FLIR Cloud™ Client allows you to connect to multiple systems from a PC or Mac.
19.1 Home Page
The Home Page allows you to access all the tabs within the software. Each tab allows you
to access different features.
To open tabs:
Click a tab from the Home Page to open it or click the
from within any tab to open a new tab.
19.2 Live View
The Live View tab is where you can view live video from connected systems.
To view live video from a system:
1. Click
2. Click and drag a DVR, NVR, group, or individual camera to open live video. To access
individual cameras, you can click + to expand groups or systems.
and then click to create a Live View tab.
button at the top of the screen
#LX400051; r. 1.0/23100/23101; en-US
81
Page 92
19
Using FLIR Cloud™ Client for PC or Mac
19.2.1 Live View Controls
1. Live display: Double-click to expand the area. Right-click to access additional options.
Hold the mouse over the display area to access the camera toolbar.
Camera toolbar:
1.1. Streaming quality: Shows the bitrate and resolution for the stream, and shows
if display is showing the Sub Stream or Main Stream.
1.2. Manual recording: Click to start/stop manual recording.
1.3. Snapshot: Click to save a snapshot.
1.4. Mute/unmute: Click to mute/unmute audio (audio camera required).
1.5. Not supported.
1.6. Instant playback: Plays back the most recently recorded video from the cam-
era. By default, it will play back the last 5 minutes of recorded video from the
camera.
1.7. Digital zoom: Click to enable digital zoom mode. Click and drag over the dis-
play area to zoom on the camera. Then click and drag to pan. Click the icon
again to zoom out.
1.8. Disconnect.
1. Split-screen mode: Click to select split-screen layout.
2. Aspect ratio: Use the drop down menu to select the aspect ratio for the selected
camera. Original uses the actual aspect ratio of the image. Full-win stretches the im-
age to fill up the entire display area.
#LX400051; r. 1.0/23100/23101; en-US
82
Page 93
19
Using FLIR Cloud™ Client for PC or Mac
3. Full-screen: Click to open full-screen mode. Press ESC to exit full-screen mode.
4.
Save view: Click to save the current display layout and open cameras as a view.
Then enter a name for the view.
5.
Start/stop tour: Click to start the tour. During the tour the client will cycle through
all saved views every few seconds. Click again to stop the tour.
6. PTZ Controls: Controls for PTZ cameras (not included). See 19.3 Controlling PTZ
Cameras, page 84 for details.
7. View: Click View to access view menu. Then double-click on a view to open it in the
display area.
8. Devices: Shows a list of groups, cameras, and systems connected to the client. Drag
items to the display area to open live video. Right-click to view additional options.
19.2.2 Opening Live View in Multiple Monitors
If your computer has multiple monitors, you can open more than one Live View tab and
move them to secondary monitors. This allows you to monitor cameras on multiple monitors at the same time.
NOTE
Using multiple monitors significantly increases the amount of computing resources necessary to run the
application and may affect performance.
To open Live View in multiple monitors:
1. Click
and then click to create a Live View tab.
#LX400051; r. 1.0/23100/23101; en-US
83
Page 94
19
Using FLIR Cloud™ Client for PC or Mac
2. Click and drag the tab outside of the client window to create a new window. You can
drag the window to one of the secondary monitors.
Result
19.3 Controlling PTZ Cameras
If you have PTZ cameras (not included), you can control them using the client.
NOTE
You must ensure the PTZ camera is properly connected to your system and your system is configured to
detect it before you can control them using the client.
To control PTZ cameras:
• Click the display area with the PTZ cameras and use the on-screen PTZ controls.
#LX400051; r. 1.0/23100/23101; en-US
84
Page 95
19
Using FLIR Cloud™ Client for PC or Mac
PTZ controls:
1. Open menu: Click to open camera OSD menu controls. This feature may not be supported for all camera models.
2. Move camera: Click the arrows to move the camera.
Click
to open dynamic zoom mode. Then click and drag in the video area to zoom
in the camera on an area.
3. Zoom +/-: Click to zoom the camera in and out.
4. Focus +/-: Click to increase/decrease the focus.
5. Iris +/-: Click to increase/decrease the iris.
6. Advanced: Click to access advanced PTZ controls.
19.3.1 PTZ Presets
Presets will save a camera position for quick retrieval.
To add presets:
1. Click
2. Click
to open the Advanced controls. Select Preset.
.
#LX400051; r. 1.0/23100/23101; en-US
85
Page 96
19
Using FLIR Cloud™ Client for PC or Mac
3. Select the number of the preset you would like to add.
4. Move the camera to the desired position.
5. Click
to save the current position as a preset.
To go to a saved preset:
1. Select the preset number from the list or click
to go to the currently selected
preset.
19.3.2 PTZ Tours
Tours will cycle through a set of presets.
To configure a PTZ tour:
1. Click
2. Click
to open the Advanced controls. Select Tour.
.
3. Under Cruise ID, select the number of the tour you would like to configure.
4. (Optional) Under Cruise Name, enter a name for the tour.
#LX400051; r. 1.0/23100/23101; en-US
86
Page 97
19
Using FLIR Cloud™ Client for PC or Mac
5. Use the chart to select which presets you would like to include in the tour and the order
of presets.
• Preset: Select the preset number.
• Time(s): Enter the time in seconds the camera will remain on the selected preset.
• Operation: Click
to add a preset to the tour. Click to delete a preset from
the tour.
6. Click OK to save changes.
To run a PTZ tour:
1. Select the tour number and click
.
19.3.3 PTZ Pattern
Patterns automatically cycle the camera between two positions.
To create a pattern:
1. Click
to open the Advanced controls. Select Pattern.
2. Select the number of the pattern you would like to set up.
3. Move the camera into the desired start position.
4. Click
to start recording the pattern.
5. Move the camera to the desired end position. Then, click
pattern.
To run a pattern:
1. Select the pattern number and click
#LX400051; r. 1.0/23100/23101; en-US
.
to stop recording the
87
Page 98
19
Using FLIR Cloud™ Client for PC or Mac
19.3.4 PTZ Scan
Scan automatically cycles between a left and right point.
To set up scan mode:
1. Click
to open the Advanced controls. Select Scan.
2. Move the camera to the desired left position and click .
3. Move the camera to the desired right position and click
To run scan mode:
1. Click
.
19.3.5 PTZ Pan
Pan makes the camera continuously pan 360°.
To run Pan mode:
1. Click
2. Click
to open the Advanced controls. Select Pan.
.
.
19.4 Playback
You can use Playback mode to playback video saved on systems connected to the client.
To access Playback mode:
• Click
#LX400051; r. 1.0/23100/23101; en-US
and then click to create a Playback tab.
88
Page 99
19
Using FLIR Cloud™ Client for PC or Mac
To playback video:
1. Check the channels you would like to play back from in the Device List.
2. Under Type, check the file types you would like to search for.
• All: All recordings.
• General: Continuous recordings.
• MD: Motion recordings.
• Alarm: Alarm recordings. Your system must support alarm devices (not included) to
use this feature.
3. Under Stream, select Main Stream to search for Main Stream recordings (high quality) or Sub Stream to search for Sub Stream recordings (smaller file size).
4. Select the start time and end time for your search under From and To. You may not
search more than 24 hours of video.
5. Click Search. Wait for the client to find video saved to the system.
6. Click inside the play back bar to start playback.
#LX400051; r. 1.0/23100/23101; en-US
89
Page 100
19
Using FLIR Cloud™ Client for PC or Mac
19.5 Playback Controls
1. Display area: Double-click to expand/return to split-screen mode. Hold the mouse
over the display area to open the camera toolbar.
• Snapshot: Click to save a snapshot.
•
Digital zoom: Click to enable digital zoom mode. Then, click and drag to zoom
in. Click and drag to pan the camera. Click
again to zoom out.
2. Event: Click to view recordings based on a list of events and files.
3. Record: Click to view recordings on a timeline.
4. Sync: Click to sync playback between channels. This forces all channels to playback
from the same time.
5. Pause/play.
6. Stop.
7. Frame-by-frame: Click to advance the video by a single frame.
8. Playback speed: Use the slider to adjust the playback speed.
9. Mute.
10. Volume.
11. Split-screen: Select split screen configuration.
12. Full-screen: Click to open playback in full-screen. Press ESC to exit full-screen.
13. Timeline zoom: Use the slider to zoom in/out on the timeline.
14. Playback timeline: Shows recordings from the selected channels on a timeline. Click
inside the timeline to start playback or select a playback time. Each type of recordings
is shown in a different color. Continuous recordings are green, motion recordings are
yellow, and alarm recordings are red.
15. Video clip: Click to start a video clip. You can download video clips to your hard drive.
#LX400051; r. 1.0/23100/23101; en-US
90
Loading...