Digimerge DPZ16TO27, DPZ16WO37 Instruction Manual

Copyright © 2009 Digimerge Technology Inc.

www.digimerge.com

Right For Business

™

INSTRUCTION MANUAL

English Version 1.0

INDOOR/OUTDOOR

PTZ CAMERA

DPZ16TO27
DPZ16WO37

Speed Dome Camera Instruction Manual 2/49

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION : TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO NOT OPEN THE COVERS.

NO USER SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONAL

This lightning flash with arrowhead symbol is intended to alert the user to
the presence of un-insulated "dangerous voltage" within the product's
enclosure that may be of sufficient magnitude to constitute a risk of electric
shock to persons.

This exclamation point symbol is intended to alert the user to the presence
of important operating and maintenance (servicing) instructions in the
literature accompanying the appliance.

This Device compiles with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:

(1) This device may not cause harmful interface, and
(2) This device must accept any interference received, including

interference that may cause undesired operations.

Speed Dome Camera Instruction Manual 3/49

Important Safety Guide

1. Read, heed and follow all the Instructions
Read all the safety and operating instructions before using the product.

2. Keep this manual
Keep this manual for reference in future.

3. Attachments / Accessories
Use only the attachments or accessories specified by the manufacturer.

4. Installation

z Do not install near any heat resources such as radiators, heat registers, stoves, or other

appratus including amplifiers that product heat. Improperly installed product may fall,
cause serious injury to a child or adult and damage the product.

z Do not block any ventilation holes or openings. Install in accordance with the

manufacturer’s instructions.

z Use only with the cart, stand, tripod, bracket, mounting devices, or table specified by

the manufacturer.

z Installation should be done only by qualified personnel and conform to all the

instructions by the manufacturer.

z Refer all servicing to qualified service personnel.
z Unless the product is specifically marked as IP66, more than IP66 or confirmed by the

manufacturer, it is designed for indoor use only and it must not be installed where
exposed to rain and moisture.

z Do not load on the product.
z Use stainless steel hardware to fasten the mount.
z To prevent damage from water leakage when installing a mount outdoors on a roof or

wall, apply sealant properly around holes.

z These servicing instructions are for use by qualified service personnel only. To reduce

the risk of electric shock, do not perform any servicing other that contained in the
operationg instructions unless you are qualified to do so.

z Use only replacement parts specified by the manufacturer.

5. Power source

This product should be operated only from the type of the power source indicated on the
marking label.

NOTICE

Speed Dome Camera Instruction Manual 4/49

Caution

 Operating

z Before using, make sure that the power supply and others are properly installed.
z While operating, if any abnormal condition or malfunction is observed, stop using the

product immediately and then contact your local dealer.

 Handling

z Do not disassemble or tamper with the parts inside the product.
z Do not drop or subject the product to shock and vibration as this can damage the

product.

z Care must be taken when you clean the clear dome cover. Especially, scratch and dust

will ruin the quality of the product.

 Installation and Storage

z Do not install the product in areas of extreme temperature, which exceed the allowable

range.

z Avoid installing in humid or dusty places.
z Avoid installing in places where radiation is present.
z Avoid installing in places where there are strong magnetic fields and electric signals.
z Avoid installing in places where the product would be subject to strong vibrations.

NOTICE

Speed Dome Camera Instruction Manual 5/49

① Introduction

Feat ures 6
Package Components 8
Main Part Description 9

② Installation

DIP Switch Setup 10

Installation with Ceiling Mount Bracket 13

Installation with Wall Mount Bracket 14

Wiring and Cabling 15

③ Operation

Check Point before Operation 18

Check Points for Preset and Pattern Function before Operation 18

OSD Menu 19

Reserved Preset (Hot Keys) 19

Preset 20
Swing 20

Pattern 21

Group 22

Other Functions 22

OSD Display 24

④ OSD Menu

Quick Programming Guide 25

Main Menu 25

Display Setup 26

Privacy Zone Mask Setup 27

Camera Setup 29

Motion Setup 34

Preset Setup 37
Swing Setup 39

Pattern Setup 40

Group Setup 41

System Initialize 44

⑤ Specifications

45

Dimension 49

TABLE OF CONTENTS

Speed Dome Camera Instruction Manual 6/49

Fe at ur es

 Powerful Zoom Camera & Setup Options

z Image Sensor : 1/4" Double density interline transfer CCD (DPZ16WO37 model)

1/4" Super HAD color CCD (DPZ16TO27 model)

z Zoom : ×27 Optical Zoom, ×12 Digital Zoom (DPZ16TO27 model)

×37 Optical Zoom, ×12 Digital Zoom (DPZ16WO37 model)

z Day & Night, Privacy Mask, WDR and HLC (WDR :

DPZ16WO37 model

only)

z SNR (Super Noise Reduction) Function
z Various Focus Mode : Auto-Focus, Manual Focus, Semi-Auto Focus
z Various Setup Options in OSD Menu.

 Powerful Pan/Tilt Functions

z MAX. 360°/sec High Speed Pan/Tilt Motion
z With the Vector Drive Technology, Pan/Tilt motions are accomplished along the

shortest path. As a result, the time to target view is remarkably short and the video on
the monitor is very natural in monitoring.

z With the Micro-Stepping Control Technology, the video looks very natural at high

zoom magnification during a jog operation on a controller since the camera can be
controlled by 0.05°/sec. Hence it is very easy to make the camera focus on desired
target views at high zoom magnification. Additionally it is easy to make the camera
focus on desired positions with zoom-proportional pan/tilt movement.

 Preset, Pattern, Swing, Group, Privacy Mask and More…

z MAX. 127 Presets are programmable and each preset can have its own parameter

values independently from the other presets.
For an example, refer to the below table.

Preset No. White Balance Auto Exposure ••• Label Remarks

Preset 1 Case A Case 3 “ENTRANCE”

Preset 2 Case C Case 5 “WAREHOUSE”

Preset 3 Case V Case 2 “OFFICE”

•••

Preset 95 − − − − Reserved for OSD Menu

•••

Preset 128 Case K Case 9 “TERRACE”

INTRODUCTION

1

Speed Dome Camera Instruction Manual 7/49

z MAX. 8 sets of Swing are programmable. This function is that the camera moves

repetitively between two preset positions at programmed speeds.

z MAX. 4 Patterns are programmable. This function is that the camera memorizes the

path (mostly curve path) by the joystick of the controller and revives the trajectory
operated by the joystick as closely as possible.

z MAX. 8 sets of Group are programmable. This function is that the camera memorizes

the combination of Presets, Pattern and/or Swings sequently and runs Presets, Pattern
and/or Swings repetitively. A Group can be combined upto 20 functions with any of
Preset/Pattern/Swing.

z MAX. 8 Privacy Masks are programmable, not to intrude on any other’s privacy.

 PTZ(Pan/Tilt/Zoom) Control

z With the RS-485 communication connection, MAX. 255 units of cameras can be

connected to a single controller.

z Pelco-D or Pelco-P protocols can be selected as a control protocol in the current

firmware version.

 OSD(On Screen Display) Menu

z OSD menu is provided to display the status of camera and to configure the functions

interactively.

z The information such as Camera ID, Pan/Tilt Angle, Direction, Alarm Input and Preset

is displayed on screen.



Alarm In/Out Function(Only for the models which have I/O function)

z 3 alarm sensor inputs and 1 alarm sensor outputs are available.
z The camera can be set to move to a Preset position or to run functions such as Pattern,

Swing and Group when there are external sensor activations. Also “Post Alarm”
function is possible, which is supposed to activate after user-defined time period and
sequentially in succession to the action by external sensor activations.

 Reserved Presets(Hot Keys)

z Most camera setup options can be set up easily and directly with the reserved presets

(Hot Keys), without entering into OSD menu. For more information, refer to “Reserved
Presets(Hot Keys)” in this manual.



Perfect Outdoor Environment Compatibility and Easy Installation

z The fans and heaters are built-in in the camera for cold and hot temperature

environment. Also idealistic mechanical design protects the camera from water and
dust. (IP66 when installed properly with wall mount bracket only)

INTRODUCTION

1

Speed Dome Camera Instruction Manual 8/49

Package Component

 Product & Accessories

z Main Body & Surface Mount Bracket z Default Accessories

[Main Cable, Wrench]

z Accessories for The Models with Alarm In/Out

Function [I/O Cable]

 Brackets (Optional)

z Wall Mount Bracket (Optional)

[Screws : Machine M5×15, Hex Lag #14×50]

z Ceiling Mount Bracket (Optional)

[Screws : Machine M5×15, Anchor Bolt 3/8"×70]

INTRODUCTION

1

Speed Dome Camera Instruction Manual 9/49

Main Part Description

D

IP Switc

h

Dome Cover

Sensor I/O Port (I/O Model)

Main Connector

Mounting Hook

Mounting Screw Hole

z Dome Cover Do not detach the protection vinyl from the dome cover before

finishing all the installation process to protect the dome cover from
scratches or dust.

z DIP Switch Used to set up camera IDs and protocols.

z Mounting Hook Used to assemble the main body with wall mount bracket or

ceiling mount bracket. Insert the mounting hooks into the holes on
the surface of the main body and turn the main body.

z Mounting Screw Hole Used to assemble the main body with a bracket with screws.

z Main Connector Us ed f or the powe r wire, th e vide o cabl e and the R S-485

communication cable connection.

z Sensor I/O Port Used for the sensor in/out connection. (The sensor I/O function

possible models only)

INTRODUCTION

1

Speed Dome Camera Instruction Manual 10/49

DIP Switch Setup

Before installing the camera, set up the DIP switch to configure the camera ID and the
communication protocol.

 Camera ID Setup

ON

ON

12345678

z ID numbers of cameras are set up with binary numbers.

See the examples shown below.

Pin 1 2 3 4 5 6 7 8

Binary Value 1 2 4 8 16 32 64 128

ex) ID=5 on off on off off off off off
ex) ID=10 off on off on off off off off

z The camera ID range is “1~255”. Camera ID must not be

“0”!

z The factory default of the camera ID is “1”.
z Match the camera ID with the Cam ID setting of your DVR

or Controller to control the camera.

z If you are connecting a single camera to a controller,

terminate the camera. When connecting more than one
camera to a single controller, terminate the last camera on
the communication line. The last camera means the camera
farthest in cable length from the controller.

z Note that the total length of the communication cable

between a controller and the camera(s) on the same
communication line must be less than 1.2Km.

INSTALLATION

2

Speed Dome Camera Instruction Manual 11/49

 Communication Protocol Setup

1234

ON

ON

z Select an appropriate Protocol with the DIP switch combination.

Switch Mode

P0

(Pin 1)

P1

(Pin 2)

P2

(Pin 3)

Protocol

OFF OFF OFF PELCO-D, 2400 bps

ON OFF OFF PELCO-D, 9600 bps

OFF ON OFF PELCO-P, 4800 bps

ON ON OFF PELCO-P, 9600 bps

Others Reserved

z Match the camera protocol with the camera protocol in the setting of

your DVR or controller to control the camera.

z Adjust the DIP switch after turning off the camera. If you changed the

camera protocol by changing the DIP S/W, the change will be effective
after you reboot the camera.

z The factory default protocol is “Pelco-D, 2400 bps”.

INSTALLATION

2

Speed Dome Camera Instruction Manual 12/49

 Terminal Resistor Setup

1234

ON

ON

T

he terminal resistor is used for the following cases.

z Case 1 : In case that the control cable length between a camera and

a controller is relatively very long (1:1 Connection)

If the communication cable length is very long, the electrical signal will
bound in the terminal point. This reflected signal causes distortion of
original signal. Accordingly, the camera can be out of control. In this
case, the terminal resistor of both sides i.e. the camera and the
controller must be set to ‘ON’ state.

z Case 2 : In case that multiple cameras are connected to a

controller.

Due to similar reasons with the case 1, the terminal resister of the
controller and the last camera must be set to ‘ON’ state. The last camera
means the camera farthest in cable length from the controller. Do not
turn on the terminal resistor of all the cameras on the same
communication cable.

Controller

#1 #2 #n

Terminal Resistor ON

RS-485

Terminal Resistor

OFF

Terminal Resistor

OFF

Terminal Resistor

ON

INSTALLATION

2

Speed Dome Camera Instruction Manual 13/49

Installation with Ceiling Mount Bracket (Optional)

① Remove the ceiling tile from the ceiling

and cut a hole whose diameter is
30~40mm on the ceiling tile to pass the
wire(s) and cable(s) through to the upside
of the ceiling. (In case of the wiring and
cabling through the mounting surface
only) Then prepare the ceiling mount
bracket. Pull the wire(s) for the system as
below. (Anchor Bolt 3/8"×70)

② Pull the wire(s) and cable(s) for the

system as below. Wire the cable(s) to the
ports. Insert the mounting hooks into the
holes on the surface of the main body and
turn the main body. Assemble the main
both with the camera mount adaptor with
the 3 screws. (Machine M5×15)

③ Screw the dome cover to the main body

and remove the protection vinyl from the
dome cover.

Important Notice

z Before starting the installation, make sure that the Camera ID and Protocol are set up properly.
z To adjust the installation height from the mounting surface, the pipe and coupler should be needed

between the surface mount part of the ceiling mount bracket and the camera mount part of the ceiling
mount bracket. Note that they are not supplied by the manufacturer.

INSTALLATION

2

Speed Dome Camera Instruction Manual 14/49

Installation with Wall Mount Bracket (Optional)

① Make a hole whose diameter is 30~40mm

on the mounting surface to pass the
wire(s) and cable(s) through the mounting
surface. (In case of the wiring and cabling
through the mounting surface only) Then
prepare the wall mount bracket. Pull the
wire(s) and cable(s) for the system as
below. Attach the wall mount bracket to
the mounting surface. (Hex Lag #14×50)

② Pull the wire(s) and cable(s) for the

system as below. Wire the cable(s) to the
ports. Insert the mounting hooks into the
holes on the surface of the main body and
turn the main body. Assemble the main
both with the camera mount adaptor with
the 3 screws. (Machine M5×15)

③ Screw the dome cover to the main body

and remove the protection vinyl from the
dome cover.

Important Notice

z Before starting the installation, make sure that the Camera ID and Protocol are set up properly.

INSTALLATION

2

Speed Dome Camera Instruction Manual 15/49

Wiring and Cabling

RS-485

BNC

SENSOR I/O

MAIN CABLE

I/O CABLE

POWER

MONITOR

CONTROLLER / DVR

IR
SENSOR

DOOR
SWITCH

 Port Description

z Main Cable

Port Pin Number (RJ45) Connector / Wire Color Signal

1 Video +

2,4

BNC Connector

Video −

5 Red RS-485 +

3 Yellow RS-485 −

7 Orange Power +

6,8 White Power −

z I/O Cable

Port Pin Number (RJ25) Wire Color Signal

1 Blue IN COM +

2 Yellow IN 1 −

3 Green IN 2 −

4 Red IN 3 −

5 Black OUT A

6 White OUT B

z Audio Cable

Port Pin Number Connector / Wire Color Signal

1 RCA (Yellow) Audio IN

2 Audio GND

3 RCA (White) Audio OUT

INSTALLATION

2