Digimerge D4202 User Manual

lP Video Router

& TLR-DVR Controller

Models: D4202

Installation / User Manual

Digimerge Technologies Inc.

CAUTION

RISK OF ELECTRIC SHOCK. DO NOT OPEN .

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT

EXPOSE THE UNIT TO RAIN OR MOISTURE

The lightning flash with arrowhead symbol, within an equilateral

triangle, is intended to alert the user to the presence of un -insulated
"dangerous voltage" within the product's enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateraltriangle is intended to
alert the user to the presence of importantoperating and

!

maintenance (servicing) instructions in th e literature accompanying

the appliance.

!

This equipment has been tested and found to comply with the limits For a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference ina residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
(which can be determined by turning the equipment off and on), the user is
encouraged to try to correct the interference by one or more of the following
measures:

• Increase the separation between the equipment and the camera, DVR and/or

monitor.

• Connect the equipment into an outlet on a circuit different from that to which
the DVR, monitor is connected.

Consult the dealer or an experienced radio or television technician for help.

-i-

CONTENTS:

GENERAL PRECAUTIONS --------------------------------------------------------------------------------------­INTRODUCTION & FEATURES ---------------------------------------------------------------- -----------------

PACKAGE CONTENTS ---------------------------------------------------------------- ---------------------------

Getting StartedGetting Started

IP ADDRESS --------------------------------------------------------------------------------------------------------­REAR PANEL --------------------------------------------------------------------------------------------------------­BOTTOM PANEL---------------------------------------------------------------- ------------------------------------­HARDWARE CONNECTIO N AT SERVER SITE-------------------------------------------------------------

Static IP SettingStatic IP Setting

SOFTWARE INSTALLATION------------------------------------------------------------------------------------­IP SETTING-----------------------------------------------------------------------------------------------------------­Video Web Server SETTING-------------------------------------------------------------------------------------­DVR REMOTE SETTING ------------------------------------------------------------------------------------------­PIN CONFIGURATION---------------------------------------------------------------------------------------------­CONNECTING TO A PC VIA THE INTERNET----------------------------------------------------------------

Dynamic IP Setting Dynamic IP Setting

WHAT IS A DYNAMIC IP ADDRESS---------------------------------------------------------------- -----------­SOFTWARE INSTALLATION------------------------------------------------------------------------------------­SYSTEM RESET-----------------------------------------------------------------------------------------------------­DDNS REGISTRATION FOR A DYNAMIC IP ADDRESS-------------------------------------------------­CONNECTING THE PC TO A ROUTER / ROUTER LOGIN----------------------------------------------­ROUTER SETTING-------------------------------------------------------------------------------------------------­IP SETTING-----------------------------------------------------------------------------------------------------------­VIDEO WEB SERVER SETTING--------------------------------------------------------------------------------­DVR REMOTE SETTING ------------------------------------------------------------------------------------------­PIN CONFIGURATION---------------------------------------------------------------------------------------------­CONNECT ALL DEVICES -----------------------------------------------------------------------------------------­CONNECTING TO A PC VIA THE INTERNET---------------------------------------------------------------

1
2
3

3
4
4
5

6
8

9
11
12
13

14
14
14
14
16
19
21
22
24
24
25
25

Operation GuideOperation Guide

SOFTWARE OPERATION AT THE REMOTE SITE -------------------------------------------------------­CONTROL PANEL & BASIC OPERATION ------------------------------------------------------------------­PLAYBACK OPERATION ---------------------------------------------------------------------------------------­ADVANCED SETTING -------------------------------------------------------------------------------------------­FAQ’S ------------------------------------------------------------------------------------------------------------------­SPECIFICATIONS ---------------------------------------------------------------- -----------------------------------­APPENDIX#1 DVR CONTROL ---------------------------------------------------------------- ------------------­APPENDIX#2 SENDING E-MAIL --------------------------------------------------------------------------------­APPENDIX#3 SOFTWARE DOWNLOAD ---------------------------------------------------------------------­REFERENCE NOTES-----------------------------------------------------------------------------------------------­LIMITED WARRANTY---------------------------------------------------------------- ------------------------------­CARE & MAINTENANCE---------------------------------------------------------------- ---------------------------

-iii-

26
27
28

29
32
33
34
36
37
38
39
40

GENERAL PRECAUTIONS:

1. Read Instructions
All of the safety and operating instructions should
be read and understood before the product is used.

2. Retain Instructions
The safety and operating instructions should be
retained for future reference.

3. Heed Warnings
All warnings on the product and the instruction
manual should be followed.

4. Follow Instructions
All operating and use instructions should be followed
for optimal performance

5. Cleaning
Disconnect this video product from the power supply
before cleaning. Do not use liquid cleaners or aerosol
cleaners. Use a damp cloth for cleaning.

6. Attachments
Do not use attachments not recommended by the
video product manufacturer as they may cause
hazards.

7. Water and Moisture
Do not use this product near water - for example,
near a bathtub, wash bowl, kitchen sink, wet
basement, or near a swimming pool.

8. Accessories
Use this product only with a stand, tripod, bracket or
table recommended by the manufacturer or sold
with the product. Any mounting of the product
should follow the manufacturer’s instructions.

9. Ventilation
This product should never be placed near or over a
radiator or heat register. This product should not be
placed in a built -in installation, such as a book case
or rack, unless proper ventilation is provided or the
Manufacturer’s instructions have been adhered to.

10. Power Source
This product should be operated from the type of
Power source indicated by the marking label. If you
are not sure of the type of power supply to your
location, consult your product dealer or your local
Power company

11. Power Cord Protection
Power supply cords should not be routed so that
they are likely to be walked on or pinched by items
placed on or near them

12. Lightning
For added protection, unplug this product from its
outlet during a lightning storm. This will prevent
damage to the video product due to lightning and
power surges

13. Overloading
To avoid the risk of fire and electric shock, do not
plug this product into an over-loaded power supply.

14. Object and Liquid Entry
Never push objects into the openings of this product
as they may touch dangerous voltage points that
may result in fire or electric shock. Never spill

liquid of any kind on this product.

15. Servicing
Do not attempt to service this product yourself as
opening or removing covers may expose you to
voltage or other hazards. Refer all servicing to
qualified service personnel

16. Damage Requiring Service
Disconnect this product from the power supply
and refer servicing to qualified service
personnel under the following conditions:
a. When the power supply cord or plug is damaged
b. If objects have fallen into the product
c. If the product has been exposed to rain or liquids
d. If the product does not operate normally by

following the instruction manual. Adjust only

the controls that are covered in the instruction
manual as an improper adjustment may result
in damage and will often require extensive work
by a qualified service technician to restore

the product to its normal operation

e. If the product has been dropped or the cabinet

has been damaged

f. When the product displays a distinct change in

performance - this indicates a need for service

17. Replacement Parts
When replacement parts are required, be sure the
technician uses replacement parts specified by
the manufacturer. Unauthorized substitutions may
result in fire, electric shock, or other hazards.

18. Safety Check
Upon completion of any service to this product
ask the service technician to perform safety
checks to determine that the product is in
proper working condition.

19. Grounding or Polarization
This product is equipped with a three-wire
grounding-type plug, a plug having a third
(grounding) pin and will only fit into a
grounding-type power outlet. This is a safety
feature. If you are unable to insert the plug
into the outlet, contact your electrician to
replace your obsolete outlet. Do not defeat the
safety purpose of the grounding-type plug.

20. Power Lines
An outside antenna system should not be
located in the vicinity of overhead power lines
or other electric light or power circuits, or where
it can fall into such power lines or circuits.
When installing an outside antenna system,
extreme care should be taken to keep from
touching such power lines or circuits as contact
with them might be fatal.

21. Wall or Ceiling Mounting
The product should be mounted to a wall or ceiling
only as recommended by the manufacturer.

22. Heat
The product should be situated away from heat
such as radiators, heat registers, stoves, or other
products (including amplifiers) that produce heat.

-1-

INTRODUCTION & FEATURES:

Introduction
Thank you for purchasing the IP Video Router and TLR-DVR Controller. This is an internet

based digital video server capable of connecting up to 2 channels of video sources. The Video
Web Server turns a standalone recorder into an IP-enabled, networkable recorder. It broadcasts
compressed live video on -line (Intranet/Internet) via an Ethernet connection. It also enables DVR
series products and cameras to connect to the internet for remote monitoring or remote control.

This is a self -contained Web Server, meaning that you can access the camera server by
browsing the website over the internet using a standard browser (such as Explorer or Netscape).
The user friendly intuitive software allows for simple management, configuration and monitoring.

The system contains an image compression chipset that is capable of delivering standard JPEG
and real-time video into a limited network bandwidth

Features

• Compatible with most CCTV Products.

• Empowers all video output devices watching and controlling on the Internet or LAN.

• Auto Network Reconnection (ANR).

• Support alarm triggers recording & watch dog function.

• Support Dynamic IP address via a Router.

• Support 4 alarm inputs.

• Duplex function, record and playback simultaneously at client site.

• Auto e-mail warning system & images uploading function (to FTP site) th at will remind you
if an external alarm was triggered.

• Intelligent non-stoppable recording function after ANR.

• Support Multi AP screens and HTTP display (IE browser).

• Unique video player.

-2-

PACKAGE CONTENTS:

IP Video Router & TLR-DVR Controller Owner’s Manual & CD

Terminal block Crossover LAN cable

CHECK YOUR PACKAGE TO MAKE SURE THAT YOU RECEIVED THE COMPLETE

SYSTEM, INCLUDING THE COMPONENTS SHOWN ABOVE.

Power Adapter & Cord

GETTING STARTED:

Before installation, contact your ISP (Internet Service Provider)
for your own IP address.

Note : The bundled software is compatible with the following Windows operating
systems : WIN2000, WIN2003 and WINXP. It is not recommended to use with WIN98
& WIN ME, which may cause system conflictions with the software.

-3-

CONTROL - REAR PANEL:

1 2 3 4 5

1. LAN

Connect the RJ45 standard pass through cable to the internet, ordirectly to a PC using
the crossover cable

2. ACT & LINK LED’s (Actual & Link)

When these LED’s are blinking it indicates that the network is in operation

3. VIDEO INPUT (BNC, 2 channels)

Connect to a video source, such as a camera or DVR video output.

4. ALARM I/O (optional for advanced applications)

Connect control devices, such as a DVR, Motion Sensors, external
alarm signal inputs, etc

5. POWER

Plug in the supplied power adaptor (12V ).

BOTTOM PANEL :

Bottom

3

RESET BUTTON (at the bottom of the Video Web Server)

Push this button for more than 5 seconds to reset the settin g back to the default
setting.

-4-

HARDWARE CONNECTION AT SERVER SITE:

A . Connection Structure

NOTE: The RS -485 to control
the DVR is optional.

1. Connect the video output of the camera or DVR to the video input of the Video Web Server.

2. Connect the PC to the Video Web Server for IP setting.

3. Connect the Video Server to the ADSL or CABLE MODEM with a Static IP address.

4. Connect PC with Internet and remote control Video Web Server.

B .Connection Application

-5-

STEP 1: SOFTWARE INSTALLATION – STATIC IP SETTING:

1. Put the attached CD into the CD-ROM. The application program will install on your PC.
Note: The CD contains a self-running installation that automatically starts when the CD is

inserted. Follow the instructions for installation as indicated in the next few pages.

2. Press “Next”.

3. Choose the destination location and press “Next”.

-6-

4. Set the program shortcut setting and press “Next”.

5. Press “Next” to begin copying the files

6. After the installation, the following files listed below will appear in your assigned path or
file folder. There will be 6 files and 1 folder.

-7-

STEP 2: IP SETTING

1. Using the Crossover LAN cable connect the Video Web Server to the PC.
Note : In some operating environments, users might need the standard CAT5 cable.

RJ-45 POWER

2. Network setting for the PC. (The instruction is based on Win XP O/S. If your Operating
System is Win 2000 or Win 2003, the setup procedure is similar to that of Win XP O/S.)

3. Click on “Properties” for TCP/IP setup

Click twice

-8-

4. Click on “INTERNET PROTOCOL (TCP/IP)” and then select “Properties” to setup

5. Click on “Use the following IP address” and set the IP address and subnet mask

NOTE :

1. Before changing the PC network setting,
please write down the original network
setting in order to recover the original
setting after the setup. (for static IP users)

2. The IP address should be

192.168.1.XXX. The setting of “XXX”
could be set from 1 to 254 Do not use 10
since 192.168.1.10 is the default IP ); the
subnet mask is 255.255.255.0.

STEP 3: VIDEO WEB SERVER SETTINGS

1. To configure the Server IP, please click twice to enter the setup.

2. Key in the User Name, Password, and Server IP (The default setting for the User Name is
admin and the default Password is admin ; Server IP is 192.168.1.10, Port : 80). Click on

OK to connect.

-9-

3. When you see the control bar, this means that you have successfully logged into the
program on the Video Web Server. Click on “System Config” to set up.(NOTE: If you don’t
connect a camera or DVR to the Video Web Server, the only th ing you will see is the control
bar.)

SYSTEM CONFIG

4. In the Peripheral setting, set the baud rate, ID and model that you want to remotely
control later. Press the “APPLY” to enable the change after the setting.

5. Click on “System Config” again. In the Network setting, set the server IP, gateway, net
mask and DNS provided from your local ISP (internet service provider). Press
“APPLY” to enable the change after the setting.

-10-

6. Disconnect the PC and Video Web Server, and link the static IP to the RJ-45 video web
server.

Static IP

STEP 4: DVR REMOTE SETTING

1. Connect the DVR and monitor.

2. In the “Remote” setting, set the baud rate and ID the same as the “Peripheral” setting
in the Video Web Server. Set the remote mode to RS-485 (see example below).

A. 1 / 4 CH DVR

B. 4 / 9 / 16 CH DMR

(MENU)

TIMER

CAMERA

RECORD

ALARM

DWELL

REMOTE

SYSTEM

EVENT

(MENU)

SEARCH

TIMER

RECORD

CAMERA

SYSTEM

EVENT

(REMOTE)

REMOTE MODE : RS-485

BAUD RATE : 2400

ID : 001

(SYSTEM)

:
:

REMOTE MODE : RS-485

BAUD RATE : 2400

REMOTE ID : 001

-11-