Digilock Australia DL880 User Manual

Preface

Welcome to use smart fingerprint lock, in the hope that this manual will bring convenience to you when

installing . We are compiling writing manual, have done their best to ensur e that information in the

manual is correct, if you find any unclear in the specification, or wrong infomation, please do not hesitate

to contact our dealer or after-sales service department.

☆Copyright statement

Description image in manual, the final explanation right owned by the company. For any imitation,

reproduction is a tort.

☆Upgrade instructions

Due to the rapid development of science and technology, in order to meet the needs of users to

continuously improve and upgrade, there is no any prior notice if any difference.

Important Notification

1、Can be widely used in villa , family security doors, outside door, office, etc.

2、Security door lock body suggested using world pole anti-theft locks, while wooden door no need world

pole anti-theft locks.

3、Please make sure the right install direction according to your acctually needs.

4、Middle installed, door thick 50-100 mm ; if side installed,please check when the partial loading square

shaft lock bravery, handle, for screw specifications are appropriate, if not applicable, please contact the

dealer or manufacturer.

5、Ensure that the mechanical keys should be installed outside of the door.

6、 After installation, first test under the condition of mechanical key to open the door, the password to

open the door (e.g., input 123456 # to open the door), both are under normal service, then can close and

set the function.

7、Intelligent lock is a kind of high-tech products, the application environment is very important.So it is

necessary to do a good job of waterproof, dustproof, and collision avoidance when decoration.

8 、 Door lock installation quality directly affect the door lock normal use, it is recommended that you

choose regular professional installation, operating according to the manufacturer to provide installat ion

standards. Not to install the operating and protect the relevant enclosed logo.

9、After installation and debugging, please initialize the empty door lock, empty all fingerprints, password,

CARDS, to regist er their own management password, user passwords, card and fingerprint, prevent the

others steal your password, leave a security risk.

10、After period of time, when the battery is low, low pressure alar m will be sent every time the door

buzzer hint, at this tim e, please replace the battery in time and pay attention to negative and positive to

ensure the normal use of lock.

11、If you were on business trip or do not use the lock for a long tim e, please take mechanical keys, and

take out the battery, in order to ensure the service life of the lock.

12 、 For small Fingerprint and younger users, it is recommended that you use thumb registered

fingerprints, and the same user registration more than two fingerprints, improve the fingerprint

acquisition success rate.

The direction of the door and lock

1、The direction of the door

As shown below.door direction have four kinds:

2、According to the direction of the door lock body latch adjustment and on the socket head screw

Allen screw in the right place

View A

1、Products normally should be right way using, no need to adjust;

2、Left open the Allen screw in need to adjust to left open position, the lock body inclined tongue needs to

change direction;

Latch bolt commutation method:

Using screwdriver to push latch bolt,

Make latch bolt completely secondary lock the side panel and rotate 180º

Installation instructions

1.1 Cut-size

Please see the attached 1:1 hole template drawing

1.2 Assembly drawing is as follows:

1.3 Technical parameters:

Basic

Information

Surface treatment

Fashion Siver, Red Bronze,Rose Gold,Green Bronze

Size(mm)

330L*78W*28H

Universal lock body

6068 double quick lock body(Can be equipped with

other specifications lock body.

Super grade B cylinder

Two Keys

Basic
Function

Openingup mode

Fingerprints,Passwords,M1 Card, Remote

control,Key

Lock Function

Anti-lock function

Fingerprint category

Optical fingerprint/Semiconductor fingerprint

Touch Mode

Capacitive type

False Reject Rate

≤0.15%

False Accept Rate

≤0.00004%

Number of fingerprint

≤300

Number of passwords

≤300

Number of cards

≤

300

Resolution

500DPI

Static Current

≤55UA(Battery can be used for more than 1 year

Operating Current

≤250MA (Strong Driving force)

Operating Tempreture

-10 ºC ~ 60 ºC

Operating Humidity

20%~95%

Opening time

5S

Power Supply

6V( 4*AA Alkaline battery)

Low Voltage Alarm

4.5V

Numbers of Password digit

6-10 digits(Plus Anti Peep password-Total 20 digits

CChinese Voice Navigation

Human Voice

Chinese LCD Screen

Yes

Passwords prevent peep

Yes

Combination Unlocking mode

Any 2 groups of unlocking

G.W

Front plate+lock body

Around 5.3KG