Product Guide
RFID Interface
Bolt Mechanism
Shared Use Functionality
Cue locks with an RFID interface are operated with an RFID credential or by an ADA compliant User Key. Manager Keys provide management
access and external power. Programming is accomplished via a Programming Key unique to the lock system.
Lock Parts
Front Unit
Key Slot
User Credential
Reader
Key Button
LED Usage Indicator
Shared Use
RFID CardUser Key
RFID
CARD
Rear Unit
Cover Plate
RFID Adhesive
Label
Connection Options
Lock Mounting Holes
Cover Plate
Screws
1/2" (12.7 mm)
Deadbolt
RFID Keyfob RFID Wristband
Cable
Pin
Keys
User Key Manager Key* Programming Key**
Operates the lock
Overrides user access
Allows management inspection
Provides external power
Programs Manager Keys
Sets lock functionality
*Up to 25 Manager Keys may be programed to each lock **1 Programming Key allowed per lock group
•• •
Key Insertion
••
••
••
•
•
NextLock logo must face up.
1
Product Guide
RFID
CARD
Manager
RFID Interface
Bolt Mechanism
Shared Use Functionality
Setup
Locks are shipped with factory default settings (only operates by pressing `). Setup must be completed to program the Programming Key
and Manager Keys or Manager RFID Credentials to all the locks.
1324
Insert the Programming Key.
A two-tone beep will be heard
and the LED will turn on.
While the LED is on, insert one
Manager Key or present one
Manager RFID Credential at a time.
A two-tone beep will be heard for
each Manager Key or Manager
RFID Credential programmed.
Insert the Programming Key.
A two-tone beep will be heard
and the LED will turn off.
Repeat above steps for each lock
or follow instructions to Express
Register Manager Credentials to
set up all locks.
Programming Instructions
Express Register Manager Credentials
The Programming Key can quickly program the same Manager Keys and Manager RFID Credentials to operate multiple locks.
1
Go to the lock already programmed to operate with the Manager Keys and
Manager RFID Credentials.
Press and hold
seconds followed by 2 sets of two-tone beeps after 10 seconds) then release.
The LED will turn on
` for 10 seconds (a two-tone beep will be heard after 5
.
2
While the LED is on, insert the Programming Key Insert the Programming Key.
A two-tone beep will be heard and the LED will turn off.
3
At each lock to be programmed, insert the Programming Key.
A two-tone beep will be heard and the LED will fl ash once to indicate
successful programming.
* The Programming Key will continue to function in Express Registration mode until it is used to operate a lock.
2
4a 4b
To end Express Registration mode:
Go to any programmed lock.
Press ` then insert the Programming Key.
Press ` then insert the Programming Key again to return the bolt to the
original position.*
Product Guide
RFID
CARD
Manager
Programming Instructions
Add Manager Keys and RFID Credentials
Manager Keys can be programmed to the locks at any time.
12 43
RFID Interface
Bolt Mechanism
Shared Use Functionality
Go to a lock requiring additional
Manager Keys.
Press and hold ` for 5 seconds (a
two-tone beep will be heard after 5
seconds) then release.
The LED will turn on.
While the LED is on, insert the
Programming Key.
A two-tone beep will be heard.
Insert each additional Manager
Key or Manager RFID Credential
one at a time.
A two-tone beep will be heard for
each Manager Key or Manager
RFID Credential programmed.
Insert the Programming Key.
A two-tone beep will be heard
and the LED will turn off.
Repeat above steps for each lock
or follow instructions to Express
Register Manager Credentials to
program the same Manager Keys
to multiple locks.
Replace Keys
Replacement keys must be purchased and programmed to the locks to prevent the lost/stolen keys from operating a lock.
1
To replace the Programming Key:
Note the order or serial number (found on the lock’s rear unit).
2
Contact Digilock Support to purchase a replacement Programming Key.
1a 1b
To replace the Manager Keys:
Collect all remaining Manager Keys.
Go to any lock operated by the lost/stolen manager credentials. Press
and hold ` for 5 seconds (a two-tone beep will be heard after 5 seconds)
then release.
The LED will turn on.
2a 2b
While the LED is on, insert the Programming Key.
A two-tone beep will be heard and the LED will remain on.
Insert the Programming Key again.
Three sets of two-tone beeps will be heard and the LED will turn off. All
previously programmed Manager Keys and Manager RFID Credential
are erased.
Follow instructions to Add Manager Keys and RFID Credentials to
program the intended Manager Keys to the locks.
3
RFID
CARD
RFID
CARD
Programming Instructions
Request Functionality Change
132
Product Guide
RFID Interface
Bolt Mechanism
Shared Use Functionality
LED Usage Indicator
Shared Use
Assigned Use
Note the order or serial number (found on the
lock’s rear unit).
Note the current color of the LED. To change the functionality of the locks (between
shared use and assigned use), contact Digilock
Support to request a Function Key.
Operating Instructions - In Shared Use Functionality
In shared use functionality, the user presents a User RFID Credential or inserts any User Key to lock and the same User RFID Credential or
User Key to unlock. Once unlocked, the lock is available for a different user.
1a
Operate with a User RFID Credential
To lock: Close the door. Press ` then present any User RFID Credential.
To unlock: Press ` then present the same User RFID Credential.
the door.
1b
Open
1a
Operate with a User Key
To lock: Close the door. Insert any User Key.
To unlock: Insert the same User Key. Open the door.
1b
1a
Operate with a Manager Key
To unlock: Insert a valid Manager Key. Open the door.
To relock: Close the door. Insert a valid Manager Key.*
* If a valid Manager Key is used to relock, the previous user credential will continue to operate the lock.
4
1b
Product Guide
RFID Interface
Bolt Mechanism
Shared Use Functionality
Support
Error Condition Indicators
10 rapid beeps:
The lock is binding, meaning either door alignment or items in the locker are preventing the lock from operating. Press on the door while
operating the lock. If error condition persists, contact Digilock support for assistance.
2 s ets of three beeps:
The batteries are low. Replace the batteries.
Does not Unlock with the User RFID Credential or User Key
The lock does not recognize the User RFID or User Key. For immediate access, operate with a valid Manager Key.
Does not Operate with a Manager Key
The lock does not recognize the Manager Key. Follow instructions to Add Manager Keys and RFID Credentials to program the Manager
Key to the lock. For immediate access, operate with another valid Manager Key.
Does not Operate with the Programming Key
The lock does not recognize the Programming Key. If the Programming Key has been replaced, operate with the Replacement
Programming Key. Contact Digilock support for additional assistance.
No Audible Feedback when = is Pressed
▪
The batteries may need to be replaced. For immediate access, operate with a valid Manager Key.
▪
The front unit may not be properly connected to the rear unit. Remove the lock from the door and check the connection.
Battery Replacement (shown with cable rear unit)
It is not necessary to uninstall the lock from the door. In case of battery failure, operate with a valid Manager Key.
123
Remove the screws and the cover plate. Pull the battery pack from the rear housing.
030718
Replace with four premium alkaline
AA batteries.
Place the battery pack back into the rear
housing and screw cover plate in place.
Phone: 707 766 6000
www.digilock.com | sales@digilock.comPG-NLQR-AD-DEN
Loading...