Digilock Lockup M Product Manual

Product Guide

Keypad Locks

Lockup M is a keypad lock designed to operate for shared or assigned use applications. In shared use functionality, the user chooses
any available locker and enters a self-selected 4-digit code to lock and the same code to later unlock. Once unlocked, the locker is
available for a different user. In assigned use functionality, the user is assigned a specifi c locker and a 4-digit code or User Key to operate
the lock. A Programming Key unique to the lock system programs up to 25 Manager Keys to the locks for management access, external
power, and inspection.

M

Shared & Assigned Use Functionality

Lock Parts

Front Unit

Key Slot

123

456

789

C Button Key Button

C0

LED Usage Indicator

Shared Use
Assigned Use

Numeric Keypad

Rear Unit

Keys

User Key Manager Key* Programming Key**

Operates the lock
Overrides user access
Allows management inspection
Provides external power
Registers Manager Keys
Assigns user credential (in assigned use)
Sets lock functionality

*Up to 25 Manager Keys may be registered to each lock **1 Programming Key allowed per lock group.

•••

••

••

••

•

Cover Plate

Mounting Holes

Cover Plate Screws

3/8" (9.5mm) Springbolt

Key Insertion

•

•

LockUp logo must face left.

Initial Setup

New locks operate only by pressing = `. Locks must be setup to allow full operation.

a. Touch the Programming Key to the key slot until a two-tone beep is heard and the LED turns on.
b. Touch each Manager Key to the key slot. A two-tone beep will be heard for each Manager Key that is successfully registered.
c. Touch the Programming Key to the key slot until a two-tone beep is heard and the LED turns off.
d. Repeat above steps for each lock or follow Express Register Manager Key(s) instructions to setup all locks.

Express Register Manager Key(s)

The Programming Key can quickly register the same Manager Key(s) to operate multiple locks.

a. Go to the lock registered with the Manager Key(s).
b. Press =` 66 `. The LED will turn on.
c. Touch the Programming Key to the key slot until a two-tone beep is heard and the LED turns off.
d. At each lock to be registered, touch the Programming Key to the key slot until a two-tone beep is heard and the LED fl ashes once

to indicate successful registration.

e. End express registration,* go to any registered lock and press =` then touch the Programming Key to the key slot to operate the lock.

* The Programming Key will continue to function in express registration mode until it is used to operate a lock.

Product Guide

Keypad Locks

M

Shared & Assigned Use Functionality

Programming Instructions

Register/Add Manager Key(s)

Manager Key(s) can be registered to a lock after Initial Setup has been completed.

a. Go to the lock requiring Manager Key(s).
b. Press =` 55 `. The LED will turn on.
c. Touch the Programming Key to the key slot until a two-tone beep is heard.
d. Touch each Manager Key to the key slot. A two-tone beep will be heard for each Manager Key that is successfully registered.
e. Touch the Programming Key to the key slot until a two-tone beep is heard and the LED turns off.
f. Repeat above steps for each lock or follow Express Register Manager Key(s) instructions to register the same Manager Key(s)

to multiple locks.

For Lost or Stolen Keys

For a lost or stolen Programming Key:

A replacement Programming Key must be purchased and registered to the lock(s) to prevent the lost/stolen Programming Key from
accessing/programming a lock.

For lost or stolen Manager Key(s):

All registered Manager Keys must be erased and only the remaining Manager Keys must be registered to the lock(s) to prevent the lost/
stolen Manager Key from accessing a lock. Purchase additional Manager Key(s) from an authorized distributor.

a. Collect all remaining Manager Key(s).
b. Press
c. Touch the Programming Key to the key slot until a two-tone beep is heard.
d. Touch the Programming Key to the key slot again until three sets of two-tone beeps are heard and the LED turns off. All previously

e. Follow Register/Add Manager Key(s) instructions to register the remaining Manager Key(s).

=`55`

registered Manager Key(s) are erased from the lock.

. The LED will turn on.

Set Lock Functionality

Each lock can be set for either shared or assigned use functionality. The default functionality is shared use. Press = to check
functionality. If in shared use, LED is red. If in assigned use, LED is green.

Set lock for assigned use functionality:

a. Press =` 65 `. The LED will turn on.
b. Touch the Programming Key to the key slot until a two tone beep is heard and the LED turns off.
c. Follow Assign User Credential instructions to assign a User Code or User Key to operate the lock.

Set lock for shared use functionality:

a. Press =` 56 `. The LED will turn on.
b. Touch the Programming Key to the key slot until a two tone beep is heard and the LED fl ashes once.

Auto Unlock (for shared use functionality only)

When in shared use functionality, each lock can be programmed to auto unlock after a set number of hours. The default setting is OFF
(does not auto unlock).

To turn on Auto Unlock:

a. Press =` 95 ` then touch the Programming Key to the key slot until the LED turns on.
b. Set the number of hours: Press 1 - 99 `. Two sets of two-tone beeps will be heard and the LED will turn off.

For example: Press 4 ` to set the lock to auto unlock after 4 hours.

To turn off Auto Unlock:

a. Press =` 94 `. The LED will start to fl ash.
b. Touch the Programming Key to the key slot until a two tone beep is heard and the LED turns off.