Digiever DS-2032, DS-4005, DS-4009, DS-4012, DS-4016 User Manual

...

Download

Network Video Recorder

User Manual

1.0.0.21

Information in this document is subject to change without notice.

Table of Contents

Chapter 1. Introduction .............................................................................. 1

1.1 Hardware Description................................................................................... 2

1.1.1 DS-2000 Series ................................................................................... 2

1.1.2 DS-4000 Series ................................................................................... 3

1.1.3 DS-1100 Pro Series ............................................................................ 4

1.1.4 DS-2100 Pro Series ............................................................................ 5

1.1.5 DS-4200 Pro Series ............................................................................ 6

1.1.6 DS-4200-RM Pro Series ..................................................................... 7

1.1.7 DS-8200-RM Pro Series ..................................................................... 8

1.1.8 DS-1100 Pro+ Series.......................................................................... 9

1.1.9 DS-2100 Pro+ Series........................................................................ 10

1.1.10 DS-4200 Pro+ Series........................................................................ 11

1.1.11 DS-4200-RM Pro+ Series ................................................................. 12

1.1.12 DS-8200-RM Pro+ Series ................................................................. 13

1.1.13 DS-4300 Pro+ Series........................................................................ 14

1.1.14 DS-4300-RM Pro+ Series ................................................................. 15

1.1.15 DS-8300-RM Pro+ Series ................................................................. 16

1.2 LED Indicators Status ................................................................................... 17

1.2.1 DS-2000 Series ................................................................................. 17

1.2.2 DS-4000 Series ................................................................................. 19

1.2.3 DS-1100 Pro Series .......................................................................... 21

1.2.4 DS-2100 Pro Series .......................................................................... 22

1.2.5 DS-4200 Pro Series .......................................................................... 23

1.2.6 DS-4200-RM Pro Series ................................................................... 25

1.2.7 DS-8200-RM Pro Series ................................................................... 27

1.2.8 DS-1100 Pro+ Series........................................................................ 29

1.2.9 DS-2100 Pro+ Series........................................................................ 30

1.2.10 DS-4200 Pro+ Series........................................................................ 31

1.2.11 DS-4200-RM Pro+ Series ................................................................. 33

1.2.12 DS-8200-RM Pro+ Series ................................................................. 35

1.2.13 DS-4300 Pro+ Series........................................................................ 37

1.2.14 DS-4300-RM Pro+ Series ................................................................. 39

1.2.15 DS-8300-RM Pro+ Series ................................................................. 41

1.3 Dual Display Solution: HDMI/VGA/DVI-I Connection ........................... 43

Chapter 2. NVR Installation ...................................................................... 44

2.1 Remote Web Browser PC System Requirements .................................... 44

2.2 Connect to NVR ........................................................................................... 45

2.2.1 Quick Guide ..................................................................................... 45

2.2.2 Install EZ Search .............................................................................. 45

2.2.3 Install NVR Decoder ........................................................................ 54

2.2.4 Install NVRPlayer ............................................................................. 56

2.2.5 Install NVR Check ............................................................................ 62

2.2.6 User Manual ..................................................................................... 66

2.2.7 Browse CD ....................................................................................... 66

2.2.8 Activate Live View Service ............................................................. 67

2.3 Quick Configuration ................................................................................... 70

2.3.1 Start .................................................................................................. 70

2.3.2 Network Settings ............................................................................. 71

2.3.3 Server Settings ................................................................................ 72

2.3.4 Date & Time ...................................................................................... 73

2.3.5 Disk Management ............................................................................ 74

2.3.6 Camera Settings .............................................................................. 82

2.3.7 Finish ................................................................................................ 91

Chapter 3. Use NVR by Local Display ..................................................... 92

3.1 Log in NVR .................................................................................................... 92

3.1.1 Anonymous login ............................................................................ 93

3.1.2 Virtual Keyboard .............................................................................. 94

3.2 Quick Configuration ................................................................................... 95

3.3 Liveview ........................................................................................................ 95

iii

3.3.1 Select View Modes on Liveview Page ........................................... 95

3.3.2 Main Functions of Liveview ............................................................ 97

3.3.3 Right Click Functions on Video Window ..................................... 104

3.3.4 Zooming with Mouse Scroll .......................................................... 107

3.3.5 Two-way Audio .............................................................................. 108

3.4 Playback .....................................................................................................108

3.4.1 Steps to Playback Videos ............................................................. 109

3.4.2 Main Functions of Playback ......................................................... 113

3.4.3 Export Files .................................................................................... 115

3.4.4 Snapshot ........................................................................................ 116

3.4.5 Zooming with Mouse Scroll .......................................................... 116

3.5 Others ...........................................................................................................116

3.5.1 Screenshot on Local Display ....................................................... 116

3.5.2 System Upgrade on Local Display ............................................... 117

3.5.3 USB Backup by Hardware or Software USB BACKUP Buttons ..... 117

Chapter 4. Use NVR by Remote Web Browser ..................................... 117

4.1 Liveview .......................................................................................................117

4.1.1 Select View Modes on Liveview Page ......................................... 118

4.1.2 Main Functions for Liveview ........................................................ 119

4.1.3 Right Click Functions on Video Window ..................................... 129

4.1.4 Zooming with Mouse scroll .......................................................... 132

4.1.5 Two-way Audio .............................................................................. 132

4.1.6 Built-in Mini-CMS Server ............................................................... 133

4.2 Multi-layer Dynamic E-Map .....................................................................137

4.2.1 Feature Introduction ...................................................................... 137

4.2.2 Add or Delete Multi-layer E-Maps ................................................ 139

4.2.3 Deploy Cameras ............................................................................ 140

4.2.4 Enable/ Disable Automatically Pop-up Event Window .............. 142

4.2.5 Event Log History .......................................................................... 143

4.3 Playback .....................................................................................................144

4.3.1 Steps to Playback Videos ............................................................. 144

4.3.2 Smart Search ................................................................................. 149

4.3.3 Main Functions on Playback ........................................................ 151

4.3.4 Zooming with Mouse scroll .......................................................... 156

4.3.5 Export ............................................................................................. 158

4.4 Play Video Files ..........................................................................................163

4.4.1 Windows Networking .................................................................... 163

4.4.2 FTP Service .................................................................................... 168

4.4.3 Naming Rule of Video files ........................................................... 171

Chapter 5. Configuration ........................................................................ 171

5.1 IP Camera ...................................................................................................171

5.1.1 Camera Settings ............................................................................ 171

5.1.2 Camera Parameter ......................................................................... 172

5.1.3 Camera Status ............................................................................... 175

5.2 Recording & Events ....................................................................................176

5.2.1 Recording Settings ........................................................................ 177

5.2.2 Recording Schedule ...................................................................... 179

5.2.3 Event & Action Management ........................................................ 181

5.2.4 Advanced Setting .......................................................................... 187

5.2.5 E-Mail .............................................................................................. 187

5.3 Disk Management .....................................................................................189

5.3.1 Disk Management .......................................................................... 189

5.3.2 File System Management .............................................................. 191

5.3.3 File Sharing Service ...................................................................... 192

5.4 Cloud ............................................................................................................194

5.4.1 Setup Dropbox Service ................................................................. 194

5.4.2 Share Files to Dropbox Server ..................................................... 195

5.4.3 Remove Configuration and Online Sync ..................................... 196

5.5 Network Setup ............................................................................................197

5.5.1 Network Setup ............................................................................... 197

5.5.2 Network Service ............................................................................. 201

5.5.3 DDNS .............................................................................................. 203

5.6 Management ..............................................................................................204

5.6.1 User Management .......................................................................... 204

5.6.2 Log System .................................................................................... 209

5.6.3 Save/Load Configuration .............................................................. 213

5.6.4 USB Backup ................................................................................... 215

5.6.5 Remote Backup ............................................................................. 221

5.6.6 External IO Device ......................................................................... 223

5.6.7 UPS Management .......................................................................... 224

5.6.8 Failover ........................................................................................... 225

5.7 System ..........................................................................................................228

5.7.1 Device Information ........................................................................ 228

5.7.2 System Upgrade ............................................................................ 229

5.7.3 Language ........................................................................................ 233

5.7.4 Date &Time ..................................................................................... 234

5.7.5 Buzzer ............................................................................................. 236

5.7.6 Reboot &Shutdown ....................................................................... 236

Appendix: Notice and Warning ........................................................................237

Chapter 1. Introduction

Before You Use This Product

When you first open the product’s package, verify that all the accessories listed on the “Package Contents” of “Quick Installation Guide” are included. Before installing

the NVR, please read the instructions in the “Quick Installation Guide” to avoid misuse and then follow the instructions in the “Hard Disk Installation” section to avoid damages due to faulty assembly or installation.

1.1 Hardware Description

1.1.1 DS-2000 Series

DS-2005/DS-2009/DS-2012/DS-2016/DS-2020/DS-2025/DS-2032

Figure 1-1. Front & Rear View of DS-2000 Series

1. Figure LED indicators: LAN, eSATA, HDD1, HDD2

2. Power button

3. USB BACKUP button- Auto video backup

4. USB 2.0 X1(Support auto video backup)

5. HDD1

6. HDD2

7. Gigabit LAN

8. USB 2.0 x 2

9. eSATA x 2

10. DI/DO (4 in 2 out)

Top to bottom: Vcc5V, GND, DI-1, DI-2, DI-3, DI-4, DO-1, DO-2

11. Reset button*

12. Power connector

13. K-lock security slot

1.1.2 DS-4000 Series

DS-4005/DS-4009/DS-4012/DS-4016/DS-4020/ DS-4025/ DS-4032

Figure 1-2. Front & Rear View of DS-4000 Series

1. LED indicators: LAN, eSATA, HDD1, HDD2, HDD3, HDD4

2. Power button

3. USB BACKUP button- Auto video backup

4. USB 2.0 x 1 (Support auto video backup)

5. HDD1

6. HDD2

7. HDD3

8. HDD4

9. Gigabit LAN

10. USB 2.0 x 2

11. eSATA x 2

12. DI/DO (4 in 2 out)

Top to bottom: Vcc5V, GND, DI-1, DI-2, DI-3, DI-4, DO-1, DO-2

13. Reset button*

14. Power connector

15. K-lock security slot

1.1.3 DS-1100 Pro Series

DS-1105 Pro/ DS-1109 Pro/ DS-1112 Pro/ DS-1116 Pro/ DS-1120 Pro/ DS-1125 Pro/ DS-1132 Pro/ DS-1136 Pro

Figure 1-3. Front & Rear View of DS-1100 Pro Series

1. Power button

2. LED indicators: HDD

3. USB 2.0 x1 (Support auto video backup)

4. USB 2.0 x1

5. Power connector

6. USB 3.0 x 2

7. DVI-I

8. eSATA x 1

9. HDMI x 1

10. Gigabit LAN

11. USB 2.0 x 2

12. Audio mic input (reserved)

13. Audio output (reserved)

1.1.4 DS-2100 Pro Series

DS-2105 Pro/ DS-2109 Pro/ DS-2112 Pro/ DS-2116 Pro/ DS-2120 Pro/ DS-2125 Pro/ DS-2132 Pro/ DS-2136 Pro

Figure 1-4. Front & Rear View of DS-2100 Pro Series

1. Power button

2. LED indicators: HDD

3. USB 2.0 x1 (Support auto video backup)

4. USB 2.0 x1

5. Power connector

6. USB 3.0 x 2

7. DVI-I

8. eSATA x 1

9. HDMI x 1

10. Gigabit LAN

11. USB 2.0 x 2

12. Audio mic input (reserved)

13. Audio output (reserved)

1.1.5 DS-4200 Pro Series

DS-4205 Pro/ DS-4209 Pro/ DS-4212 Pro/ DS-4216 Pro/ DS-4220 Pro/ DS-4225 Pro/ DS-4232 Pro/ DS-4236 Pro

Figure 1-5. Front & Rear View of DS-4200 Pro Series

1. LED indicators: LAN1, LAN2, eSATA, HDD1, HDD2, HDD3, HDD4

2. Power button

3. USB BACKUP button - Auto video backup

4. USB 2.0 x 1(Support auto video backup)

5. USB 2.0 x 1

6. HDD1

7. HDD2

8. HDD3

9. HDD4

10. Gigabit LAN x 2

11. USB 2.0 x 4

12. eSATA x 2

13. VGA output

14. HDMI output

15. DI/DO (4 in 2 out)

Top to bottom: Vcc5V, GND, DI-1, DI-2, DI-3, DI-4, DO-1, DO-2

16. Reset button*

17. Power connector

18. K-lock security slot

1.1.6 DS-4200-RM Pro Series

DS-4209-RM Pro/ DS-4212-RM Pro/ DS-4216-RM Pro/ DS-4220-RM Pro/ DS-4225-RM Pro/ DS-4232-RM Pro/ DS-4236-RM Pro

Figure 1-6. Front & Rear View of DS-4200-RM Pro Series

1. LED indicators: LAN1, LAN2, eSATA, HDD1, HDD2, HDD3, HDD4

2. Power button

3. USB BACKUP button - Auto video backup

4. USB 3.0 x 1 (Support auto video backup)

5. HDD1

6. HDD2

7. HDD3

8. HDD4

9. Gigabit LAN x 2

10. USB 2.0 x 4

11. eSATA x 2

12. VGA output

13. HDMI output

14. DI/DO (4 in 2 out)

Right to left: Vcc5V, GND, DI-1, DI-2, DI-3, DI-4, DO1, DO2

15. Reset button*

16. Power connector

1.1.7 DS-8200-RM Pro Series

DS-8209-RM Pro/ DS-8212-RM Pro/ DS-8216-RM Pro/ DS-8220-RM Pro/ DS-8225-RM Pro/ DS-8232-RM Pro/ DS-8236-RM Pro

Figure 1-7. Front & Rear View of DS-8200-RM Pro Series

1. LED indicators: LAN1, LAN2, eSATA, HDD1, HDD2, HDD3, HDD4, HDD5, HDD6,

HDD7, HDD8

2. Power button

3. USB BACKUP button - Auto video backup

4. USB 3.0 x 1 (Support auto video backup)

5. HDD1

6. HDD2

7. HDD3

8. HDD4

9. HDD5

10. HDD6

11. HDD7

12. HDD8

13. Gigabit LAN x 2

14. USB 2.0 x 4

15. eSATA x 2

16. VGA output

17. HDMI output

18. DI/DO (4 in 2 out)

Right to left: Vcc5V, GND, DI-1, DI-2, DI-3, DI-4, DO1, DO2

19. Reset button*

20. Power connector

1.1.8 DS-1100 Pro+ Series

DS-1105 Pro+/ DS-1109 Pro+/ DS-1112 Pro+/ DS-1116 Pro+/ DS-1120 Pro+/ DS-1125 Pro+/ DS-1132 Pro+/ DS-1136 Pro+/ DS-1142 Pro+/ DS-1149 Pro+/ DS-1156 Pro+/ DS-1164 Pro+

Figure 1-8. Front & Rear View of DS-1100 Pro+ Series

1. Power button

2. LED indicators: HDD

3. USB 2.0 x1 (Support auto video backup)

4. USB 2.0 x1

5. Power connector

6. USB 3.0 x 2

7. DVI-I

8. eSATA x 1

9. HDMI x 1

10. Gigabit LAN

11. USB 2.0 x 2

12. Audio mic input (reserved)

13. Audio output (reserved)

1.1.9 DS-2100 Pro+ Series

DS-2105 Pro+/ DS-2109 Pro+/ DS-2112 Pro+/ DS-2116 Pro+/ DS-2120 Pro+/ DS-2125 Pro+/ DS-2132 Pro+/ DS-2136 Pro+/ DS-2142 Pro+/ DS-2149 Pro+/ DS-2156 Pro+/ DS-2164 Pro+

Figure 1-9. Front & Rear View of DS-2100 Pro+ Series

1. Power button

2. LED indicators: HDD

3. USB 2.0 x1 (Support auto video backup)

4. USB 2.0 x1

5. Power connector

6. USB 3.0 x 2

7. DVI-I

8. eSATA x 1

9. HDMI x 1

10. Gigabit LAN

11. USB 2.0 x 2

12. Audio mic input (reserved)

13. Audio output (reserved)

1.1.10 DS-4200 Pro+ Series

DS-4205 Pro+/ DS-4209 Pro+/ DS-4212 Pro+/ DS-4216 Pro+/ DS-4220 Pro+/ DS-4225 Pro+/ DS-4232 Pro+/ DS-4236 Pro+/ DS-4242 Pro+/ DS-4249 Pro+/ DS-4256 Pro+/ DS-4264 Pro+

Figure 1-10. Front & Rear View of DS-4200 Pro+ Series

1. LED indicators: LAN1, LAN2, eSATA, HDD1, HDD2, HDD3, HDD4

2. Power button

3. USB BACKUP button - Auto video backup

4. USB 2.0 x 1(Support auto video backup)

5. USB 2.0 x 1

6. HDD1

7. HDD2

8. HDD3

9. HDD4

10. Gigabit LAN x 2

11. USB 2.0 x 4

12. eSATA x 2

13. VGA output

14. HDMI output

15. DI/DO (4 in 2 out)

Top to bottom: Vcc5V, GND, DI-1, DI-2, DI-3, DI-4, DO-1, DO-2

16. Reset button*

17. Power connector

18. K-lock security slot

1.1.11 DS-4200-RM Pro+ Series

DS-4209-RM Pro+/ DS-4212-RM Pro+/ DS-4216-RM Pro+/ DS-4220-RM Pro+/ DS-4225-RM Pro+/ DS-4232-RM Pro+/ DS-4236-RM Pro+/ DS-4242-RM Pro+/ DS-4249-RM Pro+/ DS-4256-RM Pro+/ DS-4264-RM Pro+

Figure 1-11. Front & Rear View of DS-4200-RM Pro+ Series

1. LED indicators: LAN1, LAN2, eSATA, HDD1, HDD2, HDD3, HDD4

2. Power button

3. USB BACKUP button - Auto video backup

4. USB 3.0 x 1 (Support auto video backup)

5. HDD1

6. HDD2

7. HDD3

8. HDD4

9. Gigabit LAN x 2

10. USB 2.0 x 4

11. eSATA x 2

12. VGA output

13. HDMI output

14. DI/DO (4 in 2 out)

Right to left: Vcc5V, GND, DI-1, DI-2, DI-3, DI-4, DO1, DO2

15. Reset button*

16. Power connector

1.1.12 DS-8200-RM Pro+ Series

DS-8209-RM Pro+/ DS-8212-RM Pro+/ DS-8216-RM Pro+/ DS-8220-RM Pro+/ DS-8225-RM Pro+/ DS-8232-RM Pro+/ DS-8236-RM Pro+/ DS-8242-RM Pro+/ DS-8249-RM Pro+/ DS-8256-RM Pro+/ DS-8264-RM Pro+

Figure 1-12. Front & Rear View of DS-8200-RM Pro+ Series

1. LED indicators: LAN1, LAN2, eSATA, HDD1, HDD2, HDD3, HDD4, HDD5, HDD6,

HDD7, HDD8

2. Power button

3. USB BACKUP button - Auto video backup

4. USB 3.0 x 1 (Support auto video backup)

5. HDD1

6. HDD2

7. HDD3

8. HDD4

9. HDD5

10. HDD6

11. HDD7

12. HDD8

13. Gigabit LAN x 2

14. USB 2.0 x 4

15. eSATA x 2

16. VGA output

17. HDMI output

18. DI/DO (4 in 2 out)

Right to left: Vcc5V, GND, DI-1, DI-2, DI-3, DI-4, DO1, DO2

19. Reset button*

20. Power connector

1.1.13 DS-4300 Pro+ Series

DS-4332 Pro+/ DS-4336 Pro+/ DS-4342 Pro+/ DS-4349 Pro+/ DS-4356 Pro+/ DS-4364 Pro+

Figure 1-10. Front & Rear View of DS-4300 Pro+ Series

19. LED indicators: LAN1, LAN2, eSATA, HDD1, HDD2, HDD3, HDD4

20. Power button

21. USB BACKUP button - Auto video backup

22. USB 2.0 x 1(Support auto video backup)

23. USB 2.0 x 1

24. HDD1

25. HDD2

26. HDD3

27. HDD4

28. Gigabit LAN x 2

29. USB 2.0 x 4

30. eSATA x 2

31. VGA output

32. HDMI output

33. DI/DO (4 in 2 out)

Top to bottom: Vcc5V, GND, DI-1, DI-2, DI-3, DI-4, DO-1, DO-2

34. Reset button*

35. Power connector

36. K-lock security slot

1.1.14 DS-4300-RM Pro+ Series

DS-4332-RM Pro+/ DS-4336-RM Pro+/ DS-4342-RM Pro+/ DS-4349-RM Pro+/ DS-4356-RM Pro+/ DS-4364-RM Pro+

Figure 1-11. Front & Rear View of DS-4300-RM Pro+ Series

17. LED indicators: LAN1, LAN2, eSATA, HDD1, HDD2, HDD3, HDD4

18. Power button

19. USB BACKUP button - Auto video backup

20. USB 3.0 x 1 (Support auto video backup)

21. HDD1

22. HDD2

23. HDD3

24. HDD4

25. Gigabit LAN x 2

26. USB 2.0 x 4

27. eSATA x 2

28. VGA output

29. HDMI output

30. DI/DO (4 in 2 out)

Right to left: Vcc5V, GND, DI-1, DI-2, DI-3, DI-4, DO1, DO2

31. Reset button*

32. Power connector

1.1.15 DS-8300-RM Pro+ Series

DS-8342-RM Pro+/ DS-8349-RM Pro+/ DS-8356-RM Pro+/ DS-8364-RM Pro+

Figure 1-13. Front & Rear View of DS-8300-RM Pro+ Series

21. LED indicators: LAN1, LAN2, eSATA, HDD1, HDD2, HDD3, HDD4, HDD5, HDD6,

HDD7, HDD8

22. Power button

23. USB BACKUP button - Auto video backup

24. USB 3.0 x 1 (Support auto video backup)

25. HDD1

26. HDD2

27. HDD3

28. HDD4

29. HDD5

30. HDD6

31. HDD7

32. HDD8

33. Gigabit LAN x 2

34. USB 2.0 x 4

35. eSATA x 2

36. VGA output

37. HDMI output

38. DI/DO (4 in 2 out)

Right to left: Vcc5V, GND, DI-1, DI-2, DI-3, DI-4, DO1, DO2

39. Reset button*

40. Power connector

1.2 LED Indicators Status

1.2.1 DS-2000 Series

DS-2005/ DS-2009/ DS-2012/ DS-2016/ DS-2020/ DS-2025/ DS-2032

Figure 2-1. DS-2000 Series Front Panel & RJ-45 Port

LED on Front Panel

LED

LED Color & Status

Indicate

LAN

Off

LAN Link is not established

Orange

LAN Link is established

Orange blinking

LAN is being accessed

eSATA

Off

No data transmission

Orange blinking

The eSATA device is being accessed

HDD1 HDD2

Off

Hard disk drive device is not established

Green

Hard disk drive is ready to be accessed

Green blinking

Hard disk drive data is being accessed

Red

Hard disk drive failure and need to be removed

Power

Off

Power Off

Green

Power On

BACKUP

Off

USB device is not detected

Blue

USB device is ready

Blue blinking

NVR data is being copied to the USB device (Blinking with 1Hz)

Red

Backup error occurs

LED on RJ-45 Port on Rear Panel

LED

LED Position

LED Status

Indicate

LAN

Link/Activity

(Right LED)

Off

LAN Link is not established

Yellow

LAN Link is established

Yellow blinking

LAN Activity is occurring

LAN

Speed

(Left LED)

Off

10M/100Mbps connection or no connection

Orange

1000Mbps connection

Note:

**USB BACKUP will beep and process after long pressing BACKUP button for 3 seconds. **To turn off your NVR, long pressing power button at least 2 seconds. **To turn on your NVR, long pressing power button at least 3 seconds.

Note: Once users press reset button, configuration of Camera Setting, Recording

Settings, Event & Action Setting, E-Mail Settings, and Server Settings will reset to

default. It is advised to backup system configurations. For more information, refer to detail information in user manual 5.6.3 Save/Load Configuration.

1.2.2 DS-4000 Series

DS-4005/ DS-4009/ DS-4012/ DS-4016/ DS-4020/ DS-4025/ DS-4032

Figure 2-2. DS-4000 Series Front Panel & RJ-45 Port

LED on Front Panel

LED

LED Color & Status

Indicate

LAN

Off

LAN Link is not established

Orange

LAN Link is established

Orange blinking

LAN is being accessed

eSATA

Off

No data transmission

Orange blinking

The eSATA device is being accessed

HDD1 HDD2 HDD3 HDD4

Off

Hard disk drive device is not established

Green

Hard disk drive is ready to be accessed

Green blinking

Hard disk drive data is being accessed

Red

Hard disk drive failure and need to be removed

Power

Off

Power Off

Green

Power On

BACKUP

Off

USB device is not detected

Blue

USB device is ready

Blue blinking

NVR data is being copied to the USB device (Blinking with 1Hz)

Red

Backup error occurs

LED on RJ-45 Port on Rear Panel

LED

LED Position

LED Status

Indicate

LAN

Link/Activity

(Right LED)

Off

LAN Link is not established

Yellow

LAN Link is established

Yellow blinking

LAN Activity is occurring

LAN

Speed

(Left LED)

Off

10M/100Mbps connection or no connection

Orange

1000Mbps connection

*USB BACKUP will start and beep after 3 seconds user presses BACKUP button. **To turn off NVR, users need to press power button at least 2 seconds. ***To turn on NVR, users need to press power button at least 3 seconds.

Note: Once users press reset button, configuration of Camera Setting, Recording

Settings, Event & Action Setting, E-Mail Settings, and Server Settings will reset to

default. It is advised to backup system configurations. For more information, refer to detail information in user manual 5.6.3 Save/Load Configuration.

1.2.3 DS-1100 Pro Series

DS-1105 Pro/ DS-1109 Pro/ DS-1112 Pro/ DS-1116 Pro/ DS-1120 Pro/ DS-1125 Pro/ DS-1132 Pro/ DS-1136 Pro

Figure 2-3. DS-1100 Pro Series Front Panel

Note:

**To turn off your NVR, long pressing power button at least 2 seconds. **To turn on your NVR, long pressing power button at least 3 seconds.

Note: To reset to default, please follow below methods:

Press the power button twice with the interval of one second. In other words, please press the power button in the 1st second and press the power button again in the 2nd second. It will be easier to operate the reset to default with the assistance of watch or clock.

Note: Once users press reset button, configuration of Camera Setting,

Recording Settings, Event & Action Setting, E-Mail Settings, and Server Settings

will reset to default. It is advised to backup system configurations. For more information, refer to detail information in user manual 5.6.3 Save/Load

Configuration.

1.2.4 DS-2100 Pro Series

DS-2105 Pro/ DS-2109 Pro/ DS-2112 Pro/ DS-2116 Pro/ DS-2120 Pro/ DS-2125 Pro/ DS-2132 Pro/ DS-2136 Pro

Figure 2-4. DS-2100 Series Front Panel

Note:

**To turn off your NVR, long pressing power button at least 2 seconds. **To turn on your NVR, long pressing power button at least 3 seconds.

Note: To reset to default, please follow below methods:

Note: Once users press reset button, configuration of Camera Setting, Recording

Settings, Event & Action Setting, E-Mail Settings, and Server Settings will reset to

default. It is advised to backup system configurations. For more information, refer to detail information in user manual 5.6.3 Save/Load Configuration.

1.2.5 DS-4200 Pro Series

DS-4205Pro/ DS-4209Pro/ DS-4212Pro/ DS-4216Pro/ DS-4220Pro/ DS-4225Pro/

DS-4232 Pro/ DS-4236 Pro

Figure 2-5. DS-4200 Pro Series Front Panel & RJ-45 Port

LED on Front Panel

LED

LED Color & Status

Indicate

LAN

Off

LAN Link is not established

Orange

LAN Link is established

Orange blinking

LAN is being accessed

eSATA

Off

No data transmission

Orange blinking

The eSATA device is being accessed

HDD1 HDD2 HDD3 HDD4

Off

Hard disk drive device is not established

Green

Hard disk drive is ready to be accessed

Green blinking

Hard disk drive data is being accessed

Red

Hard disk drive failure and need to be removed

Power

Off

Power Off

Green

Power On

BACKUP

Off

USB device is not detected

Blue

USB device is ready

Blue blinking

NVR data is being copied to the USB device (Blinking with 1Hz)

Red

Backup error occurs

LED on RJ-45 Connection at Rear Panel

LED

LED Position

LED/State

Indicate

LAN1 LAN2

Link/Activity

(Right LED)

Off

LAN Link is not established

Yellow

LAN Link is established

Yellow Blinking

LAN activity is occurring

LAN1 LAN2

Speed

(Left LED)

Off

10Mbps connection or no connection

Green

100Mbps connection

Orange

1000Mbps connection

*USB BACKUP will start and beep after 3 seconds user presses BACKUP button. **To turn off NVR, user needs to press power button at least 2 seconds.

Note: Once users press reset button, configuration of Camera Setting, Recording

Settings, Event & Action Setting, E-Mail Settings, and Server Settings will reset to

default. It is advised to backup system configurations. For more information, refer to detail information in user manual 5.6.3 Save/Load Configuration.

1.2.6 DS-4200-RM Pro Series

DS-4209-RM Pro/ DS-4212-RM Pro/ DS-4216-RM Pro/DS-4220-RM Pro/ DS-4225-RM

Pro/ DS-4232-RM Pro/ DS-4236-RM Pro

Figure 2-6. Front View of DS-4200-RM Pro Series & RJ-45 Port

LED on Front Panel

LED

LED Color & Status

Indicate

LAN

Off

LAN Link is not established

Orange

LAN Link is established

Orange blinking

LAN is being accessed

eSATA

Off

No data transmission

Orange blinking

The eSATA device is being accessed

HDD1 HDD2 HDD3 HDD4

Off

Hard disk drive device is not established

Green

Hard disk drive is ready to be accessed

Green blinking

Hard disk drive data is being accessed

Red

Hard disk drive failure and need to be removed

Power

Off

Power Off

Green

Power On

BACKUP

Off

USB device is not detected

Blue

USB device is ready

Blue blinking

NVR data is being copied to the USB device (Blinking with 1Hz)

Red

Backup error occurs

LED on RJ-45 Connection at Rear Panel

LED

LED Position

LED/State

Indicate

LAN1 LAN2

Link/Activity

(Right LED)

Off

LAN Link is not established

Yellow

LAN Link is established

Yellow Blinking

LAN activity is occurring

LAN1 LAN2

Speed

(Left LED)

Off

10Mbps connection or no connection

Green

100Mbps connection

Orange

1000Mbps connection

*USB BACKUP will start and beep after 3 seconds user presses BACKUP button. **To turn off NVR, user needs to press power button at least 2 seconds. *** The LED in the HDD trays are reserved.

Note: Once users press reset button, configuration of Camera Setting, Recording

Settings, Event & Action Setting, E-Mail Settings, and Server Settings will reset to

default. It is advised to backup system configurations. For more information, refer to detail information in user manual 5.6.3 Save/Load Configuration.

1.2.7 DS-8200-RM Pro Series

DS-8209-RM Pro/ DS-8212-RM Pro/ DS-8216-RM Pro/DS-8220-RM Pro/ DS-8225-RM

Pro/DS-8232-RM Pro/ DS-82326-RM Pro

Figure 2-7. Front View of DS-8200-RM Pro Series & RJ-45 Port

LED on Front Panel

LED

LED Color & Status

Indicate

LAN

Off

LAN Link is not established

Orange

LAN Link is established

Orange blinking

LAN is being accessed

eSATA

Off

No data transmission

Orange blinking

The eSATA device is being accessed

HDD1 HDD2 HDD3 HDD4 HDD5 HDD6 HDD7 HDD8

Off

Hard disk drive device is not established

Green

Hard disk drive is ready to be accessed

Green blinking

Hard disk drive data is being accessed Red

Hard disk drive failure and need to be removed

Power

Off

Power Off

Green

Power On

BACKUP

Off

USB device is not detected

Blue

USB device is ready

Blue blinking

NVR data is being copied to the USB device (Blinking with 1Hz)

Red

Backup error occurs

LED on RJ-45 Connection at Rear Panel

LED

LED Position

LED/State

Indicate

LAN1 LAN2

Link/Activity

(Right LED)

Off

LAN Link is not established

Yellow

LAN Link is established

Yellow Blinking

LAN activity is occurring

LAN1 LAN2

Speed

(Left LED)

Off

10Mbps connection or no connection

Green

100Mbps connection

Orange

1000Mbps connection

*USB BACKUP will start and beep after 3 seconds user presses BACKUP button. **To turn off NVR, user needs to press power button at least 2 seconds. *** The LED in the HDD trays are reserved.

Note: Once users press reset button, configuration of Camera Setting, Recording

Settings, Event & Action Setting, E-Mail Settings, and Server Settings will reset to

default. It is advised to backup system configurations. For more information, refer to detail information in user manual 5.6.3 Save/Load Configuration.

1.2.8 DS-1100 Pro+ Series

DS-1105 Pro+/ DS-1109 Pro+/ DS-1112 Pro+/ DS-1116 Pro+/ DS-1120 Pro+/ DS-1125 Pro+/ DS-1132 Pro+/ DS-1136 Pro+/ DS-1142 Pro+/ DS-1149 Pro+/ DS-1156 Pro+/ DS-1164 Pro+

Figure 2-8. DS-1100 Pro+ Series Front Panel

Note:

**To turn off your NVR, long pressing power button at least 2 seconds. **To turn on your NVR, long pressing power button at least 3 seconds.

Note: To reset to default, please follow below methods:

Note: Once users press reset button, configuration of Camera Setting, Recording

Settings, Event & Action Setting, E-Mail Settings, and Server Settings will reset to

default. It is advised to backup system configurations. For more information, refer to detail information in user manual 5.6.3 Save/Load Configuration.

1.2.9 DS-2100 Pro+ Series

DS-2105 Pro+/ DS-2109 Pro+/ DS-2112 Pro+/ DS-2116 Pro+/ DS-2120 Pro+/ DS-2125 Pro+/ DS-2132 Pro+/ DS-2136 Pro+/ DS-2142 Pro+/ DS-2149 Pro+/ DS-2156 Pro+/ DS-2164 Pro+

Figure 2-9. DS-2100 Pro+ Series Front Panel

Note:

**To turn off your NVR, long pressing power button at least 2 seconds. **To turn on your NVR, long pressing power button at least 3 seconds.

Note: To reset to default, please follow below methods:

Note: Once users press reset button, configuration of Camera Setting, Recording

Settings, Event & Action Setting, E-Mail Settings, and Server Settings will reset to

default. It is advised to backup system configurations. For more information, refer to detail information in user manual 5.6.3 Save/Load Configuration.

1.2.10 DS-4200 Pro+ Series

DS-4205 Pro+/ DS-4209 Pro+/ DS-4212 Pro+/ DS-4216 Pro+/ DS-4220 Pro+/ DS-4225 Pro+/ DS-4232 Pro+/ DS-4236 Pro+/ DS-4242 Pro+/ DS-4249 Pro+/ DS-4256 Pro+/ DS-4264 Pro+

Figure 2-10. DS-4200 Pro+ Series Front Panel & RJ-45 Port

LED on Front Panel

LED

LED Color & Status

Indicate

LAN

Off

LAN Link is not established

Orange

LAN Link is established

Orange blinking

LAN is being accessed

eSATA

Off

No data transmission

Orange blinking

The eSATA device is being accessed

HDD1 HDD2 HDD3 HDD4

Off

Hard disk drive device is not established

Green

Hard disk drive is ready to be accessed

Green blinking

Hard disk drive data is being accessed

Red

Hard disk drive failure and need to be removed

Power

Off

Power Off

Green

Power On

BACKUP

Off

USB device is not detected

Blue

USB device is ready

Blue blinking

NVR data is being copied to the USB device (Blinking with 1Hz)

Red

Backup error occurs

LED on RJ-45 Connection at Rear Panel

LED

LED Position

LED/State

Indicate

LAN1 LAN2

Link/Activity

(Right LED)

Off

LAN Link is not established

Yellow

LAN Link is established

Yellow Blinking

LAN activity is occurring

LAN1 LAN2

Speed

(Left LED)

Off

10Mbps connection or no connection

Green

100Mbps connection

Orange

1000Mbps connection

*USB BACKUP will start and beep after 3 seconds user presses BACKUP button. **To turn off NVR, user needs to press power button at least 2 seconds.

Note: Once users press reset button, configuration of Camera Setting, Recording

Settings, Event & Action Setting, E-Mail Settings, and Server Settings will reset to

default. It is advised to backup system configurations. For more information, refer to detail information in user manual 5.6.3 Save/Load Configuration.

1.2.11 DS-4200-RM Pro+ Series

DS-4209-RM Pro+/ DS-4212-RM Pro+/ DS-4216-RM Pro+/ DS-4220-RM Pro+/ DS-4225-RM Pro+/ DS-4232-RM Pro+/ DS-4236-RM Pro+/ DS-4242-RM Pro+/ DS-4249-RM Pro+/ DS-4256-RM Pro+/ DS-4264-RM Pro+

Figure 2-11. Front View of DS-4200-RM Pro+ Series & RJ-45 Port

LED on Front Panel

LED

LED Color & Status

Indicate

LAN

Off

LAN Link is not established

Orange

LAN Link is established

Orange blinking

LAN is being accessed

eSATA

Off

No data transmission

Orange blinking

The eSATA device is being accessed

HDD1 HDD2 HDD3 HDD4

Off

Hard disk drive device is not established

Green

Hard disk drive is ready to be accessed

Green blinking

Hard disk drive data is being accessed

Red

Hard disk drive failure and need to be removed

Power

Off

Power Off

Green

Power On

BACKUP

Off

USB device is not detected

Blue

USB device is ready

Blue blinking

NVR data is being copied to the USB device (Blinking with 1Hz)

Red

Backup error occurs

LED on RJ-45 Connection at Rear Panel

LED

LED Position

LED/State

Indicate

LAN1 LAN2

Link/Activity

(Right LED)

Off

LAN Link is not established

Yellow

LAN Link is established

Yellow Blinking

LAN activity is occurring

LAN1 LAN2

Speed

(Left LED)

Off

10Mbps connection or no connection

Green

100Mbps connection

Orange

1000Mbps connection

*USB BACKUP will start and beep after 3 seconds user presses BACKUP button. **To turn off NVR, user needs to press power button at least 2 seconds. *** The LED in the HDD trays are reserved.

Note: Once users press reset button, configuration of Camera Setting, Recording

Settings, Event & Action Setting, E-Mail Settings, and Server Settings will reset to

default. It is advised to backup system configurations. For more information, refer to detail information in user manual 5.6.3 Save/Load Configuration.

1.2.12 DS-8200-RM Pro+ Series

DS-8209-RM Pro+/ DS-8212-RM Pro+/ DS-8216-RM Pro+/ DS-8220-RM Pro+/ DS-8225-RM Pro+/ DS-8232-RM Pro+/ DS-8236-RM Pro+/ DS-8242-RM Pro+/ DS-8249-RM Pro+/ DS-8256-RM Pro+/ DS-8264-RM Pro+

Figure 2-12. Front View of DS-8200-RM Pro+ Series & RJ-45 Port

LED on Front Panel

LED

LED Color & Status

Indicate

LAN

Off

LAN Link is not established

Orange

LAN Link is established

Orange blinking

LAN is being accessed

eSATA

Off

No data transmission

Orange blinking

The eSATA device is being accessed

HDD1 HDD2 HDD3 HDD4 HDD5 HDD6 HDD7 HDD8

Off

Hard disk drive device is not established

Green

Hard disk drive is ready to be accessed

Green blinking

Hard disk drive data is being accessed Red

Hard disk drive failure and need to be removed

Power

Off

Power Off

Green

Power On

BACKUP

Off

USB device is not detected

Blue

USB device is ready

Blue blinking

NVR data is being copied to the USB device (Blinking with 1Hz)

Red

Backup error occurs

LED on RJ-45 Connection at Rear Panel

LED

LED Position

LED/State

Indicate

LAN1 LAN2

Link/Activity

(Right LED)

Off

LAN Link is not established

Yellow

LAN Link is established

Yellow Blinking

LAN activity is occurring

LAN1 LAN2

Speed

(Left LED)

Off

10Mbps connection or no connection

Green

100Mbps connection

Orange

1000Mbps connection

*USB BACKUP will start and beep after 3 seconds user presses BACKUP button. **To turn off NVR, user needs to press power button at least 2 seconds. *** The LED in the HDD trays are reserved.

Note: Once users press reset button, configuration of Camera Setting, Recording

Settings, Event & Action Setting, E-Mail Settings, and Server Settings will reset to

default. It is advised to backup system configurations. For more information, refer to detail information in user manual 5.6.3 Save/Load Configuration.

1.2.13 DS-4300 Pro+ Series

DS-4332 Pro+/ DS-4336 Pro+/ DS-4342 Pro+/ DS-4349 Pro+/ DS-4356 Pro+/ DS-4364 Pro+

Figure 2-10. DS-4300 Pro+ Series Front Panel & RJ-45 Port

LED on Front Panel

LED

LED Color & Status

Indicate

LAN

Off

LAN Link is not established

Orange

LAN Link is established

Orange blinking

LAN is being accessed

eSATA

Off

No data transmission

Orange blinking

The eSATA device is being accessed

HDD1 HDD2 HDD3 HDD4

Off

Hard disk drive device is not established

Green

Hard disk drive is ready to be accessed

Green blinking

Hard disk drive data is being accessed

Red

Hard disk drive failure and need to be removed

Power

Off

Power Off

Green

Power On

BACKUP

Off

USB device is not detected

Blue

USB device is ready

Blue blinking

NVR data is being copied to the USB device (Blinking with 1Hz)

Red

Backup error occurs

LED on RJ-45 Connection at Rear Panel

LED

LED Position

LED/State

Indicate

LAN1 LAN2

Link/Activity

(Right LED)

Off

LAN Link is not established

Yellow

LAN Link is established

Yellow Blinking

LAN activity is occurring

LAN1 LAN2

Speed

(Left LED)

Off

10Mbps connection or no connection

Green

100Mbps connection

Orange

1000Mbps connection

*USB BACKUP will start and beep after 3 seconds user presses BACKUP button. **To turn off NVR, user needs to press power button at least 2 seconds.

Note: Once users press reset button, configuration of Camera Setting, Recording

Settings, Event & Action Setting, E-Mail Settings, and Server Settings will reset to

default. It is advised to backup system configurations. For more information, refer to detail information in user manual 5.6.3 Save/Load Configuration.

1.2.14 DS-4300-RM Pro+ Series

DS-4332-RM Pro+/ DS-4336-RM Pro+/ DS-4342-RM Pro+/ DS-4349-RM Pro+/ DS-4356-RM Pro+/ DS-4364-RM Pro+

Figure 2-11. Front View of DS-4300-RM Pro+ Series & RJ-45 Port

LED on Front Panel

LED

LED Color & Status

Indicate

LAN

Off

LAN Link is not established

Orange

LAN Link is established

Orange blinking

LAN is being accessed

eSATA

Off

No data transmission

Orange blinking

The eSATA device is being accessed

HDD1 HDD2 HDD3 HDD4

Off

Hard disk drive device is not established

Green

Hard disk drive is ready to be accessed

Green blinking

Hard disk drive data is being accessed

Red

Hard disk drive failure and need to be removed

Power

Off

Power Off

Green

Power On

BACKUP

Off

USB device is not detected

Blue

USB device is ready

Blue blinking

NVR data is being copied to the USB device (Blinking with 1Hz)

Red

Backup error occurs

LED on RJ-45 Connection at Rear Panel

LED

LED Position

LED/State

Indicate

LAN1 LAN2

Link/Activity

(Right LED)

Off

LAN Link is not established

Yellow

LAN Link is established

Yellow Blinking

LAN activity is occurring

LAN1 LAN2

Speed

(Left LED)

Off

10Mbps connection or no connection

Green

100Mbps connection

Orange

1000Mbps connection

*USB BACKUP will start and beep after 3 seconds user presses BACKUP button. **To turn off NVR, user needs to press power button at least 2 seconds. *** The LED in the HDD trays are reserved.

Note: Once users press reset button, configuration of Camera Setting, Recording

Settings, Event & Action Setting, E-Mail Settings, and Server Settings will reset to

default. It is advised to backup system configurations. For more information, refer to detail information in user manual 5.6.3 Save/Load Configuration.

1.2.15 DS-8300-RM Pro+ Series

DS-8342-RM Pro+/ DS-8349-RM Pro+/ DS-8356-RM Pro+/ DS-8364-RM Pro+

Figure 2-13. Front View of DS-8300-RM Pro+ Series & RJ-45 Port

LED on Front Panel

LED

LED Color & Status

Indicate

LAN

Off

LAN Link is not established

Orange

LAN Link is established

Orange blinking

LAN is being accessed

eSATA

Off

No data transmission

Orange blinking

The eSATA device is being accessed

HDD1 HDD2 HDD3 HDD4 HDD5 HDD6 HDD7 HDD8

Off

Hard disk drive device is not established

Green

Hard disk drive is ready to be accessed

Green blinking

Hard disk drive data is being accessed Red

Hard disk drive failure and need to be removed

Power

Off

Power Off

Green

Power On

BACKUP

Off

USB device is not detected

Blue

USB device is ready

Blue blinking

NVR data is being copied to the USB device (Blinking with 1Hz)

Red

Backup error occurs

LED on RJ-45 Connection at Rear Panel

LED

LED Position

LED/State

Indicate

LAN1 LAN2

Link/Activity

(Right LED)

Off

LAN Link is not established

Yellow

LAN Link is established

Yellow Blinking

LAN activity is occurring

LAN1 LAN2

Speed

(Left LED)

Off

10Mbps connection or no connection

Green

100Mbps connection

Orange

1000Mbps connection

*USB BACKUP will start and beep after 3 seconds user presses BACKUP button. **To turn off NVR, user needs to press power button at least 2 seconds. *** The LED in the HDD trays are reserved.

Note: Once users press reset button, configuration of Camera Setting, Recording

Settings, Event & Action Setting, E-Mail Settings, and Server Settings will reset to

default. It is advised to backup system configurations. For more information, refer to detail information in user manual 5.6.3 Save/Load Configuration.

1.3 Dual Display Solution: HDMI/VGA/DVI-I Connection

DS-4200 Pro Series, DS-4200-RM Pro Series, DS-8200-RM Pro Series, DS-4200 Pro+ Series, DS-4200-RM Pro+ Series, DS-8200-RM Pro+ Series, DS-4300 Pro+ Series, DS-4300-RM Pro+ Series and DS-8300-RM Pro+ Series provide HDMI and VGA port

for local display. Users can connect both of HDMI and VGA at the same time for video output.

DS-1100 Pro Series, DS-2100 Pro Series, DS-1100 Pro+ Series and DS-2100 Pro+ Series provide HDMI and DVI-I port for local display. Users can connect both of HDMI

and DVI-I at the same time for video output.

Scenario A: If both monitors are Full HD(1920x1080),those will be shown as Full HD.

Scenario B: If both monitors are VGA (1024x768), those will be shown all as VGA.

Scenario C: If one of monitors is 1920x1080 and another is 1024x768, both monitors

are set as 1024x768

Chapter 2. NVR Installation

2.1 Remote Web Browser PC System Requirements

The following information is the minimum required specification for remote Windows PC, which users can open a remote browser from the PC to access the Linux NVR server on the network.

 Operating System

Microsoft® Windows® Vista /7 / 8 (32-bit and 64-bit)

 Browsers in Windows OS (32-bit)

Microsoft® Internet Explorer 8.0 or above, Chrome 31.0.1650.57m or above, Firefox 25 or above, Opera 17.0 or above, Safari5.1.7 or above

 CPU

For channels under 16 : Intel® Dual core CPU 3.0 GHz or above.

For channels over 16 : Intel® i5/i7 CPU 3.3 GHz or above.

 Network

Minimum 10/100 Ethernet (Gigabit Ethernet is recommended)

Note: * User is suggested to connect cameras and NVR with Gigabit switch.

 Memory

For channels under 16: DDR3 4G or above.

For channels over 16: DDR3 8G or above

 Graphics Adapter

AGP or PCI-Express, minimum 1024×768, 16 bit colors, 1G memory or above

Note: It is highly recommended to use a graphics adaptor which provides

higher than resolutions 1024 x 768 in order to experience the full benefits of the software.

 Make sure the display DPI setting is set to default at 96DPI  To set DPI value, right-click on desktop, choose “Settings” tab >>

“Advanced” >> “General.”

 CD-ROM Drive

It is necessary to read the operating instructions in the provided CD-ROM.

 Adobe Reader

It is necessary to read the operating instructions in the provided CD-ROM. The audio function will not work if a sound card is not installed in the PC.

Note: Audio may be interrupted depending on network traffic.

2.2 Connect to NVR

To begin, please insert the product CD-ROM in a PC to access the Quick Guide, User Manual and install the utilities. As user runs the product CD, the following menu is displayed.

2.2.1 Quick Guide

Click “Quick Guide” to enter the folder and double click the file to open. Please read Quick Guide to quickly understand the process of NVR installation.

2.2.2 Install EZ Search

Click “Install EZ Search” to find NVR in the network. Please follow the instructions to install and EZ Search will run automatically.

When installing EZ Search, Shield Wizard window for EZ Search will pop up. Click “Next” to continue installation.

Read the license agreement and click “I accept the terms of the license agreement”. Click “Next” to continue installation.

Select a location of destination and select a folder where the setup can install files. The default location is: C:\Program Files (x86)\NVR\EZ Search. Users can also install NVR Search in other folder by clicking “Change” and select a location as below. Click

“OK” to save the setting.

Once a folder is selected, please click “OK” to continue installation.

The window shows that the InstallShield Wizard is installing EZ Search. Please wait until the Wizard completes the installation.

The InstallShield has successfully installed NVR Search. Select “Create Desktop Shortcut”/ “Create Quick Launch Shortcut”/ “Create Start Menu Shortcut” and please click “Next” to continue.

The installation is complete. Please click “Launch application when done installing” to execute NVR Search.

After finishing the setup, the window of NVR Search will pop up. NVR Search will execute automatically and show NO., Name, IP Address, Mac Address and Model name of connected NVR.

Users can click “Search” to search NVR.

Introduction of NVR Search

NVR Search provides three kinds of toolbars for users:

1. File

You can click “Exit” to leave NVR Search and close the window.

2. Setting Configure UPnP and Network by clicking “Setting” in the top left or in the middle right.

Note: Users will be prompted to enter the login information of NVR before

being allowed to change the setting.

When accessing the NVR setting, users will be prompted to enter username and password. For the first-time use, the default username and password are admin/admin. When the correct username and password have been entered, click

“Login” to continue.

1) UPnP

Universal Plug and Play (UPnP) simplifies the process of adding a NVR to a local

area network. Once connected to a LAN, NVR will automatically appear on the internet. You can rename UPnP Name on the NVR. Click “OK” to finish the setting.

2) Network Two models are provided for setting the network: DHCP and Static IP.

3. Option

Option provides several languages

Once you click “Connect” or double click the selected NVR list, IE browser will pop up automatically for the web-based interface.

2.2.3 Install NVR Decoder

Click “Install S-NVR Decoder” to install decoder and follow

the instructions to setup.

Install Shield Wizard window will pop up and please click “Next” to continue installation.

Read license agreement and click “I accept the terms of the license agreement.” Click “Next” to continue installation.

The installation Wizard is installing NVR Decoder.

The installation is complete. Please click “Finish” to close the window.

2.2.4 Install NVRPlayer

Click “Install NVR Player” to install NVR Player and follow the

instructions to setup.

Install Shield Wizard window will pop up and please click “Next” to continue installation.

Read license agreement and click “I accept the terms of the license agreement.” Click “Next” to continue installation.

Select a location of destination and select a folder where the setup can install files. The default location is: C:\Program Files (x86)\NVR\NVRPlayer. Users can also install NVR Player in other folder by clicking “Change” and select a location as below. Click “OK” to save the setting.

Once a folder is selected, please click “OK” to continue installation.

The window shows that the InstallShield Wizard is installing NVR Player. Please wait until the Wizard completes the installation.

The InstallShield has successfully installed NVR Player. Select “Create Desktop

Shortcut”/ “Create Quick Launch Shortcut”/ “Create Start Menu Shortcut” and please click “Next” to continue.

The installation is complete. Please click “Launch application when done installing” to execute NVR Player.

After finishing the setup, the window of NVRPlayer will pop up.

Introduction of NVRPlayer

NVRPlayer allows users to view the recorded videos exported from NVR. NVR Player is a portable tool with no need to install on PC. NVRPlayer can play multi-channel videos via playlist which is exported from instant export.

Please right-click to run NVR Player as administrator

Click “Open File” button to select a video or a playlist to play videos. For more information about export videos to PC, please refer to 4.3.5 Export.

If users select a playlist to play multi-channel videos, please select cameras, start/end time. Then, click “Play” button to play videos.

NVRPlayer will display playback video time on the top-left corner for time reference.

Users can move “Time Bar” to desired time when playing recorded video

Feature introduction

 Frame by Frame Playback

Please click “Pause” button and click “Next Frame” or “Previous Frame” to find the desired video precisey.

 Snapshot

Please click “Snapshot” button to take a photo to your PC.

2.2.5 Install NVR Check

Click “Install NVR Check” to open the folder and double-click

on user manual file to read.

Install Shield Wizard window will pop up and please click “Next” to continue installation.

Read license agreement and click “I accept the terms of the license agreement.” Click “Next” to continue installation.

Select a location of destination and select a folder where the setup can install files. The default location is: C:\Program Files (x86)\NVR\NVR Check. Users can also install NVR Check in other folder by clicking “Change” and select a location as below. Click “OK” to save the setting.

Once a folder is selected, please click “OK” to continue installation.

The window shows that the InstallShield Wizard is installing NVR Check. Please wait until the Wizard completes the installation.

The InstallShield has successfully installed NVR Check. Select “Create Desktop

Shortcut”/ “Create Quick Launch Shortcut”/ “Create Start Menu Shortcut” and please click “Next” to continue.

The installation is complete. Please click “Launch application when done installing” to execute NVR Chec.

After finishing the setup, the window of NVR Check will pop up.

Introduction of NVR Check

While NVR is recording video and snapshot files, the digital watermark will be embedded automatically in the images. To ensure the security of videos and snapshots, NVR Check is a useful tool to verify whether the files are originated from NVR.

Please double click the icon to start the application. Click “OK” to choose the video clip or picture that wanted to be verified.

If the recording file is originated from NVR, the window will display “No error occur.”

If the recording file has been changed, the window will display “There is an error in the video file.”

To know more information, please ask the manufacturer by providing detailed information in “Detail” button.

2.2.6 User Manual

Click “User Manual” to open the folder and double-click on user manual file to read.

2.2.7 Browse CD

Click “Browse CD” to open the folder of current Autorun.exe file.

2.2.8 Activate Live View Service

1. Connect to NVR

After setting the EZ Search and S-NVR Decoder, users can connect to the web-based interface by the following two options: EZ Search or IE browser

1) EZ Search

Once you click “Connect” or double click the selected NVR list, the IE browser will pop up automatically.

2) IE browser

2. Enter username and password: For first-time use, the default username and password are “admin/admin.”

3. Select the languages for the UI.

4. Allow ActiveX Control

After logging in the NVR, users are recommended to install ActiveX control for the first-time installation.

1) Left-click on the description “This website wants to run the following

add-on: ‘NVR ActiveX’ from…..”

2) Left-click on the description “Run Add on.”

3) Left-click “Run” to use licensed ActiveX controls.

2.3 Quick Configuration

After users log in NVR and install the ActiveX control, the system will direct you to set Quick Configuration in five main steps. Follow the instructions of the Overview of

wizard to complete system setup.

2.3.1 Start

System will lead you to “Start” from the drop-down menu of Configuration Utility to begin.

To initial the configuration, please study the Overview of wizard first. Through five steps, the wizard will guide you to set up the system quickly.

Click “Start” in Overview of wizard page to begin Quick Configuration.

2.3.2 Network Settings

Please select “Network Settings” from the drop-down menu of Configuration Utility to begin.

Users need to adjust the settings in the Network Setup page in order to let NVR work properly within network.

 There are 2 methods to configure IP address

1. Obtain an IP address automatically (NVR Default)

Obtain an available dynamic IP address assigned by a DHCP server. If this option is selected, NVR will automatically obtain an available dynamic IP address from the DHCP server once it connects to the network.

2. Specify an IP address.

If there is no DHCP server existing in network environments, the static IP address will be given as192.168.1.245. It should be adaptable in most networking environment, and user can choose to maintain the default IP address or change it in this page. However, it’s recommended setting different IP address of NVR if there is more than one NVR in the same LAN.

To assign a static IP address to the NVR:

1. Select “Specify an IP address”

2. Enter the IP address, Subnet Mask, Default Gateway IP Address and DNS server address.

3. If IP Address is changed, user needs to log out NVR and login in again.

Click “Next” to proceed with the configuration.

2.3.3 Server Settings

Please select “Server Settings” from the drop-down menu of Configuration Utility to begin.

 Server name with UPnP Universal Plug and Play (UPnP) simplifies the process of adding a NVR to a local area

network. Once connected to LAN, the NVR will automatically appear on the internet. User can select to enable the function with UPnP and edit a sever name.

 Password Settings

Each NVR comes with a built-in “admin” account with password “admin.” It’s highly recommended to change the password upon the initial login. Enter a new password in the “New Password” field and enter it again in “Retype Password.” Since you confirm “Next,” the administrator password will be changed.

2.3.4 Date & Time

Please select “Date & Time” from the drop-down menu of Configuration Utility to begin.

1. Manual setting

Use the drop-down list and configure the time manually. Select the Year, Month, Date and Time. Time setting will be effective when you click “Next.”

2. Time Zone: Synchronize with an Internet time server automatically.

Select the time zone of your area and update the date and time of the NVR automatically with an NTP server. User also has an option to automatically adjust daylight saving time.

Configure the time and date by verifying and adjusting current local time and daylight saving to avoid the following errors:

 Incorrect display time for playback videos.  Inconsistent display time of event logs and when they actually occur.

Please enter the hostname of a valid NTP server to synchronize the server time with an Internet time server. NTP (Network Time Protocol) is a protocol to synchronize the clocks of a computer system.

2.3.5 Disk Management

Please select “Disk Management” from the drop-down menu of Configuration Utility to begin.

If hard disk is not installed in NVR, the page will show “Disk doesn’t exist.”

Once an available hard disk drive is inserted into the tray, Disk Information will show in Device Information and users can start to create new RAID Disk.

1. Disk Information

Device Information provides details of the hard disk drive: HDD Model, Serial NO., Capacity and Status.

2. Create

As the hard disk drive is available, the status of Device Information shows “Ready,” which indicates the hard disk drive is ready to be created.

Please click “Create” to enter the window for building New RAID Disk and select the hard disk drive in the Free HDDs field.

The selected hard disk drive in the Free HDDs field will be marked in blue and please click to recruit the hard disk drive into Assigned HDDs field.

The selected hard disk drive in Assigned HDDs field will be marked in blue.

Meanwhile, Target RAID Disk is ready to build RAID disk and it shows five types of disk configuration.

The introduction of disk configuration is in the below table.

Disk Configuration

Big Drive (Linear)

Big Drive is a collection of hard disk drives and does not provide any RAID protection. The data are written to the disks continuously.

Performance (Raid0)

RAID0is one larger volume with 2 or more hard disk drives. The data are written to the hard disk drives without any parity information. The total storage capacity is the sum of all hard disk drives.

Fault Tolerant (Raid1)

2 hard disk drives are required to create a RAID1 array. RAID1 can provide disk mirroring by duplicating the data between two hard disk drives.

Fault Tolerant (Raid5)

A minimum of 3 hard disk drives are required to create RAID5. The data are striped in all hard drives in a RAID5 array and the parity information is stored in each drive. If a hard disk drive fails, the array enters degraded mode. The data can be rebuilt from other member drives after installing a new drive to replace the failed one.

Fault Tolerant (Raid10)

Data are written in stripes across primary disks that have been mirrored to the secondary disks. A typical RAID 10 configuration consists of four drives, two for striping and two for mirroring

RAID 10 is supported in DS-8300-RM Pro+, DS-4300-RM Pro+, DS-4300 Pro+, DS-8200-RM Pro+, DS-4200-RM Pro+, DS-4200 Pro+, DS-8200-RM Pro, DS-4200-RM Pro and DS-4200 Pro Series.

Select a type of disk configuration, and please click “Apply” to execute building new RAID disk.

Note: Don’t turn off the server or unplug any hard drives when RAID Disk is in

building process.

Please wait. The disk configuration is in a process.

The progress is under “formatting….20%”. Please wait till 100%.

The progress is in “Create swap” and is going to finish the disk building.

Finally, the RAID disk building is complete. After the RAID disk is created, RAID List shows RAID Name and available storage devices. Device Information provides status of the hard drive: RAID Name, Level,

Capacity, Status-Active, Action State, Background Activity and Progress-none.

3. Delete

After the RAID Disk is created, “Delete” option is available. If user is going to delete RAID disk, please refer to following description.

In “Delete” option, user can remove or format RAID disk by selecting the RAID disk. In the table, RAID Name, RAID type, Capacity and Status are shown.

 Remove

Click “Remove” to delete RAID Disk. Once “Remove” is clicked, a window will

pop up to ensure the execution.

To delete RAID Disk, click “OK” to proceed.

Please wait. The deletion is in a process.

If users want to change the RAID level setting, please click ‘‘Remove.’’ After the RAID Disk is removed, the Status in Device information shows “Ready,” then users can go back to Create page to continue the new RAID level configuration.

Note: Once you remove the disk and continually create it, the recorded

video will be formatted.

 Format

Click “Format” to format the RAID disk, all recorded videos will be deleted.

Once “Format” is clicked, a window will pop up to ensure the execution.

To format RAID disk, click “OK” to continue.

Hard disk drive is formatting. Please wait for formatting until 100%.

2.3.6 Camera Settings

NVR provides two options to add new cameras: UPnP Search and Detect

1. Detect:

In this option, users are asked to enter IP Address. Check correct username and

password. Then, click “Apply” button to start adding camera.

Camera Name, Username and Password are editable.

After clicking “Apply” button, vender, username and password will be automatically filled in by vendor’s default information.

 Memorize modified username and password: NVR also can memorize username and password which is modified by users after users click “Apply” button. Then, the default username and password of that vendor will be replaced by the modified one. Next time when users add new camera of the specific vendor, username and password will be automatically filled in by new modified one.

Note: Each vendor has its own default username and password.

 Streaming Parameters

NVR provides two options to set up stream parameters: Optimization by NVR and Settings from camera.

(1) Optimization by NVR

By selecting this option, NVR will optimize settings to perform the best surveillance efficiency.

(2) Settings from camera

If users have already set up camera settings from camera webpage, NVR can adopt camera setting by selecting “Setting from Camera.” This option can largely save users’ time and effort when users install surveillance systems.

Note: It is highly recommend to use “Optimization by NVR” to perform the

best surveillance quality in both live-view and playback.

 Multi-channel Video Server NVR supports multi-channel video server feature to connect analog cameras to NVR.

Users are asked to enter IP Address. Check correct username and password.

Please click “Enable” Video Server and choose the channel number. Then, click “Apply” button.

After successfully adding cameras, NVR will display camera information in camera list.

If there is any error occurred in entering the following information, the notification window will pop up as below.

When an inappropriate address is entered, a window will pop up as below.

When an inappropriate user name is entered, a window will pop up as below.

When an inappropriate password is entered, a window will pop up as below.

 Delete

If any camera should be deleted from camera list, please click the column turning into blue and click “Delete” button.

A window will pop up to ensure the action.

To delete the camera, click “OK” to proceed.

The camera has been deleted from camera list.

 Generic RTSP/ Generic MJPEG

NVR provides the interface for users to enter RTSP/ MJPEG URLs of IP cameras to receive the video streaming from IP camera. The streaming will be applied to monitoring, recording and playback.

Generic RTSP and Generic MJPEG function can be selected in the vendor list of camera setting page.

Follow by entering the Generic URL column with proper RTSP or MJPEG URLs. If Generic RTSP is selected, RTSP port should be filled out too. Click “Apply” button to make parameters enable

The most correct URLs should be provided from each camera vendors. Users may also refer to websites

- https://www.soleratec.com/rtsp/

- http://www.ispyconnect.com/sources.aspx

2. UPnP Search:

Click “UPnPSearch” to find out UPnP devices within the LAN.

Please make sure IP camera supports UPnP Search function. Please go to IP Camera web page to enable UPnP search function.

Please wait. The UPnP search is in a process.

The available cameras in the network will be displayed. Click the camera that you would like to add in NVR, then click “Add” button.

Note: Users can click “All” to add cameras in Added column.

The Added column will show two numbers to display the total channels of the NVR and the channel numbers that has been already added in the NVR.

Please check camera information in Group add page. Then, Click “Add All” button to start adding cameras

Note: NVR will automatically fill in default username and password of each

vendor. Camera No., Camera Name, User Name and Password can be modified by users.

Memorize modified username and password: NVR will memorize username and password which is modified by users after users click “Apply” button. Then, the default username and password of that vendor will be replaced by the modified one. Next time when users add new camera of the specific vendor, username and password will be automatically filled in by new modified one.

Note: Each vendor has its own default username and password.

Note: By clicking “All” option beside Username and Password, NVR will

automatically memorize modified username and password of that camera brand.

As above example, NVR will modify default username and password of AVTECH camera and make the new username and password become AVTECH’s default username and password.

Status column in camera list will display “Successful” when cameras are successfully added in NVR.

Please click “Go to Camera Settings” button to check all camera information camera list that is successfully added in NVR.

 Multi-channel Video Server NVR supports multi-channel video server feature to connect analog cameras to NVR. Please click “Enable” Video Server and choose the channel number. Please click “Add All” button after finishing checking all camera information.

 Delete

User can click “Delete” button to remove the camera from NVR. Please click a camera and click “Delete” button.

A window will pop up to ensure the execution. Please click “OK” to proceed.

2.3.7 Finish

Please select “Finish” from the drop-down menu of Configuration Utility to begin.

Once five steps of Quick Configuration are completed, the window will show the

completed status. You can click “Back” to return to the previous steps to modify the configuration or click “Start Live view” to start monitoring.

To review the setting or information of Quick Configuration, user can also select “Quick Configuration” in the left of the Configuration main page.

Chapter 3. Use NVR by Local Display

NVR can be connected to a monitor via HDMI and VGA port to execute quick configuration and display live view.

Note: Local display feature is supported in Pro and Pro+ series.

To start local display, please check the steps below:

1. Please install at least one hard disk drive in your NVR.

2. Connect NVR and IP cameras to the network.

3. Make sure the monitor is connected to the port (HDMI /VGA/ DVI-I) of NVR rear

panel.

4. Please connect a USB mouse to the USB port of NVR.

5. Please connect power cord and connector to turn on NVR.

6. When you enter the log in interface of NVR, please enter default user name

“admin” and password “admin” and select languages.

3.1 Log in NVR

Users have to key in the correct username and password to login NVR

Resolution: User can select the resolution 1920x1080 or 1024x768 in login page, when the monitor supports both types of resolution.

3.1.1 Anonymous login

Anonymous login allows users to login without username and password.

Anonymous user can only view live monitoring and playback page in local monitor, however, the configuration page will be disable. While anonymous login is applied, system will automatically log in without authorization process after boot up.

Start to setup the anonymous login

A. Please go to “Configuration->Management->Users Management->Advance

Settings” in remote web browser.

B. Check the “Enable Anonymous Access.”

C. Enable the “Anonymous” at the local display login page, and then log in.

3.1.2 Virtual Keyboard

Users can choose to use USB keyboard for typing in local display of NVR, or fill out columns with virtual keyboard. The virtual keyboard in local display can be enabled from the right side of each column.

There are 3 types of virtual keyboard can be chosen, including Upper case, Lower case and Symbols.

-Upper case -Lower case -Symbols

Digiever DS-2032, DS-4005, DS-4009, DS-4012, DS-4016 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual