DigiBoard BCP-51W, BCP-51WH, BCP-52WA, BCP-52WAH Complete Manual

Download

Page 1

Cycling Computer

COMPLETE MANUAL

BCP-51W

BCP-51WH

BCP-52WA

BCP-52WAH

ENGLISH

Page 2

SCREEN ELEMENTS

» BCP-52WA / BCP-52WAH

» BCP-51W / BCP-51WH

Page 3

OPERATIONS BUTTON

Page 4

CONTENTS

SECTION 1 : INSTALLATION

A Hardware: Mounting bracket, wheel magnet and speed sensor

B. Heart rate: Heart rate sensor set

C. Cadence: Cadence magnet and cadence sensor

SECTION 2 : FIRST TIME SET-UP

A. Battery installation

B. Settings » Setting clock » Setting heart rate values » Setting gender » Setting weight » Setting wheel size » Setting Km/h or M/h » Setting odometer 1 » Setting total time 1 » Pairing

C. Setting home altitude

SECTION 3 : BEFORE EACH RIDE

» Trip data reset

» Home altitude calibration

SECTION 4 : ADVANCED SETTINGS

A. Second bike set-up

B. Advanced time settings

C. Advanced trip distance settings

D. Advanced heart rate settings

E. Advanced cadence settings

F. Advanced altitude settings

G. Temperature and Backlight

SECTION 5 : ADDITIONAL INFORMATION

A. Menu structure

B. Display elements

C. Functions overview

D. Troubleshooting

E. Technical specifications

10 11 12 13 14 15 15 16 16

Page 5

SECTION 1

INSTALLATION

Page 6

SECTION 1A : INSTALLATION - HARDWARE

1. Install the wheel magnet on a spoke, using a Phillips srewdriver.

2. Position the speed sensor on the fork leg to achieve the correct alignment with the wheel magnet. If needed, move the wheel magnet. When you have achieved the correct alignment, pass two zip-ties through the speed sensor and around the fork leg.

3. Re-check the alignment of the speed sensor, and tighten both zip-ties. The distance between the wheel magnet and the sensor point should be maximum 5mm.

4. Cut off the excess length of the zip-ties.

INSTALLING THE WHEEL MAGNET AND SPEED SENSOR

5. The bracket can be installed on the stem as well as the handlebar. The bracket is pre-assembled in the handlebar position.

6. If you would like to have your computer on the stem, loosen the four screws on the bracket, rotate the bracket 90 degrees and tighten the four screws.

7. Pass two zip-ties through the bracket and around the stem/handlebar. Cut off the excess length of the zip-ties.

8. Place the BBB computer in the bracket and rotate clockwise till you hear a “click” sound.

INSTALLING THE COMPUTER BRACKET

Page 7

SECTION 1B : INSTALLATION - HEART RATE

The heart rate sensors are integrated in the soft elastic belt. For a correct heart rate measurement, the belt must be positioned slightly below your chest, directly on your skin.

1. Make the two contact areas moist before you start your exercise.

2. The chest belt needs to be snug to stay in place. Slide the buckles to adjust the length of the belt for a snug but comfortable fit.

3. Press the ANT+ transmitter to the elastic belt on the two push-button connectors.

Maintenance

- Remove the transmitter from the elastic belt after every use and dry the push-buttons connectors on the transmitter. Rinse the soft elastic belt under running water after every use.

- Wash the elastic belt regularly in a washing machine at 30ºC. Use a washing pouch. Do not spin-dry, iron, dry clean or bleach the elastic belt. Do not use detergent with bleach or fabric softener.

- Never put the transmitter in the washing machine!

INSTALLING THE HEART RATE SENSOR

The sensor batteries are pre-installed. When needed, check below illustrations for correct replacement.

1. Open the battery cover by turning the cover counter clockwise.

2. Insert the battery (CR 2032) with the negative side (- ) facing up for 3 seconds. This will reset the sensor.

3. Insert the battery (CR 2032) with the positive side (+ ) facing up. Close the battery cover by turning it clockwise.

Batteries should be disposed of in compliance with local regulations.

» BATTERY REPLACEMENT FOR THE HEART RATE SENSOR

Page 8

SECTION 1C : INSTALLATION - CADENCE

1. Install the cadence magnet on the non drive train side of the crank.

2. Install the cadence sensor on the chainstay.

3. Position the cadence sensor on the chainstay to achieve the correct alignment with the cadence magnet. If needed, move the cadence magnet. The distance between the magnet and the sensor point should be maximum 3mm. When you have achieved the correct alignment, pass two zip-ties through the sensor and around the chainstay.

4. Cut off the excess length of the zip-ties.

INSTALLING THE CADENCE MAGNET AND CADENCE SENSOR

The sensor batteries are pre-installed. When needed, check below illustrations for correct replacement.

1. Open the battery cover by turning the cover counter clockwise.

2. Insert the battery (CR 2032) with the negative side (- ) facing up for 3 seconds. The will reset the sensor.

3. Insert the battery (CR 2032) with the positive side (+ ) facing up. Close the battery cover by turning it clockwise.

Batteries should be disposed of in compliance with local regulations.

» BATTERY REPLACEMENT FOR THE CADENCE SENSOR

Page 9

SECTION 2

FIRST TIME SET-UP

Page 10

SECTION 2A : FIRST TIME SET-UP : BATTERY

1. Open the battery cover by turning the cover counter clockwise.

2. Insert the battery (CR 2032) with the positive side (+) facing up. Close the battery cover by turning it clockwise

After the battery installation the first time setup menu will start automatically.

The first time setup procedure can be restarted by pressing the “AC” button on the back side the of computer.

INSTALLING BATTERY INTO THE COMPUTER

Page 11

SECTION 2B : FIRST TIME SET-UP : SETTINGS

1. To change 24HR clock or 12HR clock, press + or -.

2. To select, press M.

SETTING CLOCK

3. To set the TIME press + or - .

4. To select, press M.

Page 12

SECTION 2B : FIRST TIME SET-UP : SETTINGS

High Limit / Low Limit

For a healthy and effective training your heart rate should not be too high or too low. Your computer will warn you when you are training too hard or not hard enough. The heart rate shown on the display will start to flash when you are under or over your limits.

During an exercise test done by a sports doctor your high and low heart rate limit can be determined precisely. There is a simple, less precise, way to determine these values:

High limit = (220(man) / 224(woman)) – age) x 90% Low limit = (220(man) / 224(woman)) – age) x 60%

1. To set HI LIMIT press + or -. To select, press M.

2. To set LO LIMIT press + or - . To select, press M.

SETTING HEART RATE VALUES

Page 13

SECTION 2B : FIRST TIME SET-UP : SETTINGS

1. To set the SEX press + or - . (M = Male, F = Female).

2. To select, press M.

SETTING GENDER

Page 14

SECTION 2B : FIRST TIME SET-UP : SETTINGS

1. To change KG or LB, press + or -.

2. To select, press M.

SETTING WEIGHT

3. To set the WEIGHT press + or - .

4. To select, press M.

Page 15

This computer has wheel size presets for easy wheel size selection.

1. To set the correct wheel size press + or -. To select, press M.

SETTING WHEEL SIZE

SETTING CUSTOM WHEEL SIZE

1. When the preferred wheel size is not listed in the preset list, select CUSTOM. To select, press M.

To set the WHEEL SIZE digits press + or - . To select, press M. Repeat these steps to set the

other digits.

SECTION 2B : FIRST TIME SET-UP : SETTINGS

PRESET MM

700 700 700 700 700 700 26 26 26 26 26 26 CUSTOM

23 2096 25 2105 28 2136 32 2155 35 2168 38 2180

1.5 2010

1.9 2045

1.95 2050

2.0 2055

2.1 2068

2.2 2075 0000 - 3999

To set the most precise wheel size, do a “rollout” test.

(Make sure the tires are at the correct tire pressure)

A. Sit on the bicycle, place the valve of the front

wheel on the floor. B. Mark the floor at the valve position. C. While you sit on the bicycle, have a helper roll the

bicycle forward with one revolution of the wheel,

so that the valve is directly on the floor again. D. Mark the new position of the valve. E. Measure the distance between the two marks, in

millimeters. F. Set this value in the DigiBoard computer.

Page 16

SECTION 2B : FIRST TIME SET-UP : SETTINGS

1. To change the SPEED UNIT to KM/H or M/H, press + or -.

2. To select, press M.

SETTING KM/H OR M/H

1. It is possible to set the ODOMETER data into your new bicycle computer. To select the first digit, press + or -.

2. To select, press M. Repeat these steps to select the other digits.

SETTING ODOMETER 1

Page 17

SECTION 2B : FIRST TIME SET-UP : SETTINGS

1. It is possible to set the TOTAL TIME data into your new bicycle computer. To select the first digit, press + or -

2. To select, press M. Repeat these steps to select the other digits.

SETTING TOTAL TIME 1

1. During the pairing procedure the computer makes a secured digital connection with the sensors. Once a sensor is found the computer will show “SPD FOUND”, “CAD FOUND” and/ or “HRT FOUND”, depending on the type of sensors you are using.

During the pairing process the heart rate, cadence and speed symbol will flash in the display. When a sensor is found, the symbol will stop flashing. Before you start using your bicycle wait until the pairing process is completely finished and the computer display shows the main screen.

Once sensors are paired the connection is stored in the computer memory. The pairing process does not have to be repeated before each ride.

The pairing procedure can be repeated manually by pressing the M and F button together for 3 seconds.

Starting the pairing procedure manually is needed when sensors cannot be found or when a later bought sensor needs to be paired.

PAIRING

3s 3s

Page 18

SECTION 2C : FIRST TIME SET-UP : HOME ALTITUDE

The altitude in this computer is measured by a pressure sensitive barometer. Not only altitude, but also changing weather will influence the height showed on your computer.

Before each ride you have to calibrate the altitude to let the computer compare your home altitude with the current weather situation.

Home altitude can also be described as start altitude. The home altitude is a saved preset for easy calibration.

Are you on holiday? Save your start altitude as home for calibration before each ride.

Will your ride start from a different altitude each day? Check page 27, Advanced Altitude settings, for changing the current altitude.

Calibration of the altitude is described at page 20.

1. Start with the ALTITUDE menu (ALTI GAIN shown in display). Press M button for 3 seconds.

SETTING ALTITUDE (BCP-52WA / BCP-52WAH ONLY)

2. To set the ALTITUDE press + or -. To select, press M . Repeat to set the other digits.

3. To save the HOME ALTITUDE, press M to save the value.

SETTING HOME ALTITUDE (BCP-52WA / BCP-52WAH ONLY)

Home altitude information for your specific position can be found by various sources like maps, tourist information or on the internet.

Page 19

SECTION 3 : BEFORE EACH RIDE

SECTION 3

BEFORE EACH RIDE

Page 20

SECTION 3 : BEFORE EACH RIDE : TRIP DATA RESET

1. The TRIP data can be reset in any menu by pressing + and – button for 3 seconds.

Please note: Every trip related data is reset including CADENCE, HEART RATE and ALTITUDE. Totals like ODO and TOTAL TIME will not be reset.

TRIP DATA RESET (BCP-52WA / BCP-52WAH ONLY)

1. The TRIP data can be reset in any menu by pressing + and – button for 3 seconds.

Please note: Every trip related data is reset including CADENCE and HEART RATE. Totals like ODO and TOTAL TIME will not be reset.

TRIP DATA RESET (BCP-51W / BCP-51WH ONLY)

3s 3s

Page 21

SECTION 3 : BEFORE EACH RIDE : HOME ALTITUDE CALIBRATION

1. Start with the ALTITUDE menu (ALTI GAIN shown in display). Press + button for 3 seconds.

HOME ALTITUDE CALIBRATION (BCP-52WA / BCP-52WAH ONLY)

2. Confirm the HOME ALTI by pressing the + button. The display will now show your home ALTITUDE and is calibrated with the current weather situation.

Page 22

SECTION 4 : ADVANCED SETTINGS

SECTION 4

ADVANCED SETTINGS

Page 23

SECTION 4A : ADVANCED SETTINGS : SECOND BIKE SET-UP

Mount the bracket on your second bicycle as instructed on page 5.

Mount the wheel magnet and speed sensor on your second bicycle as instructed on page 5.

Mount the cadence magnet and sensor on your second bicycle as instructed on page 7.

1. Start with the DISTANCE menu (TRIP DIST shown in display). Press + button for 3 seconds. The second bike is selected when the is changed into n the display.

SECOND BIKE SET-UP

2. Press the M button for 3 seconds for setting the wheel size. Follow the same procedure as described on page 14.

3. Press M and F button for 3 seconds to start pairing with your second bike speed sensor and cadence sensor (if applicable). Make sure the distance between bicycle 1 and bicycle 2 is at least 10 meters.

4. To switch between bicycle 1 and bicycle 2, start with the DISTANCE menu (TRIP DIST shown in display). Press + button for 3 seconds.

3s 3s

Page 24

SECTION 4B : ADVANCED SETTINGS : ADVANCED TIME SETTINGS

The Time is set during the First-Time Set-Up, page 10.

1. To change the clock start with the TIME menu (TIME shown in display). Press M button for 3 seconds.

2. To change 24HR clock or 12HR clock, press + or - . To select press M.

3. To set the time press + or -. To select press M. Repeat these steps to set the other digits. If the 12HR clock is selected, you must also select AM or PM.

TIME SET-UP

The Total Ride Time is set during the First-Time Set-Up, page 16.

1. To change this data start with the TIME menu (TOT TIME1 shown in display). Press M button for 3 seconds.

2. To select the first digit, press + or -. To select press M. Repeat these steps to select the other digits.

To change the Total Ride Time for the second bike, repeat these step starting with TOT TIME2 shown in display.

SETTING TOTAL RIDE TIME

Page 25

SECTION 4C : ADVANCED SETTINGS : ADVANCED TRIP DISTANCE SETTINGS

The Odometer is set during the First-Time Set-Up, page 15.

1. To change this data start with the DISTANCE menu (ODOMETER1 shown in display). Press M button for 3 seconds.

2. To change the speed unit to KM/H or M/H, press + or -. To select press M.

ODOMETER SET-UP

3. To select the first digit, press + or -. To select press M. Repeat these steps to select the other digits.

To change the odometer for the second bike, repeat these step starting with ODOMETER2 shown in display.

Page 26

SECTION 4D : ADVANCED SETTINGS : ADVANCED HEART RATE SETTINGS

The user’s Heart Rate HI LIMIT and LO LIMIT are set during the First-Time Set-Up, page 11.

1. To change these limits start with the HEART RATE menu (KCAL shown in display). Press M button for 3 seconds.

2. If the display shows USER DATA, change into HR LIMIT by pressing + or - . To select press M.

3. Set the heart rate values as described on page 11.

HEART RATE LIMIT SET-UP

The User Data (Sex, Weight) are set during the First-Time Set-Up, page 12.

1. To change these data start with the HEART RATE menu (KCAL shown in display). Press M button for 3 seconds.

2. If the display shows HR LIMIT, change into USER DATA by pressing + or - . To select press M.

3. Set the SEX and WEIGHT values as described on page 12.

USER DATA SET-UP

Page 27

SECTION 4E : ADVANCED SETTINGS : ADVANCED CADENCE SETTINGS

1. To set up the distance countdown function start with the CADENCE menu (TIMER or DIST. CD shown in display). Press M button for 3 seconds.

2. To choose between DISTANCE COUNTDOWN or TIME COUNTDOWN , press + or -. To select press M.

DISTANCE OR COUNTDOWN TIMER SET-UP

3. To select the first digit, press + or -. To select press M. Repeat these steps to select the other digits.

4. To start the DISTANCE COUNTDOWN or TIME COUNTDOWN, press +.

Page 28

SECTION 4F : ADVANCED SETTINGS : ADVANCED ALTITUDE SETTINGS

Page 17 shows how to set the home altitude. The home altitude can be described as preset start altitude.

It is also possible to change the start altitude without changing the home preset. This can be useful when you want to change the start altitude without losing the saved home altitude. For example when you ride only one day on an altitude that is different from home or when your ride starts at a different altitude every day.

1. Start with the ALTITUDE menu (ALTI GAIN shown in display). Press M button for 3 seconds.

2. To set the ALTITUDE, press + or -. To select press M . Repeat to set the other digits.

3. To change between SAVE HOME and SAVE CURR press + or -. Select SAVE CURR and press M. Now the altitude in the display is changed to the altitude you entered. The preset home altitude is not changed.

HOME ALTITUDE OR CURRENT ALTITUDE (BCP-52WA / BCP-52WAH ONLY)

1. To enter the total gained altitude data manually, start with the ALTITUDE menu ( TOT ALTI shown in display). Press M button for 3 seconds.

2. To set the TOT ALTI press + or - . To select press M. Repeat these steps to set the other digits.

TOTAL ALTITUDE GAIN SET-UP (BCP-52WA / BCP-52WAH ONLY)

Page 29

SECTION 4F : ADVANCED SETTINGS : TEMPERATURE SETTINGS AND BACKLIGHT

1. To change between °C or °F start with the ALTITUDE menu (TEMP shown in display). Press M button for 3 seconds.

SETTING °C or °F (BCP-52WA / BCP-52WAH ONLY)

1. The backlight can be activated in any function by pressing the – button. The backlight will automatically go off after 3 seconds.

2. To activate the automatic backlight function press – button for 3 seconds in any function. When the automatic backlight function is activated the backlight symbol is visible in the LCD display. When automatic backlight is activated the backlight will switch on for 3 seconds when a button is pressed.

3. To switch off the automatic backlight function press – button for 3 seconds in any function. The backlight symbol will disappear from the LCD display

BACKLIGHT

Page 30

SECTION 5 : ADDITIONAL INFORMATION

SECTION 5

ADDITIONAL INFORMATION

Page 31

SECTION 5 : ADDITIONAL INFORMATION

To change between the different menu’s press M . To check different functions within a menu press F.

A. MENU STRUCTURE

SPEED PACER

The SPEED PACER compares your current speed with your average speed.

= Current speed is above average speed.

= Current speed is below average speed.

LOW BATTERY INDICATOR

When the LOW BATTERY indicator appears on the display the battery in the main unit

needs to be changed. Before changing the battery, write down your ODO and TOTAL TIME data.

The computer will automatically reset when the battery is removed. After installing a new battery you can set your ODO and TOTAL TIME data.

Batteries should be disposed in compliance with local regulations.

B. DISPLAY ELEMENTS

Page 32

SECTION 5 : ADDITIONAL INFORMATION

C. FUNCTIONS OVERVIEW

Current speed

Average speed

Maximum speed

Riding time

Trip distance

Odometer 1

Odometer 2

Total odometer (1+2)

Clock (12 / 24h)

Low battery indicator

Auto start / stop

Speed pacer

Backlight

Total riding time 1

Total riding time 2

2nd wheel size

Auto sleep

Altitude

Home altitude storage

Altitude gain / loss

Maximum altitute

Minimum altitute

Percent grade

Total altitude gain (1+2)

Temperature (°C / °F)

Heart rate

Maximum heart rate

Average heart rate

Calories used

Upper / lower limit

Cadence transmitter set (BCP-56)

Heart rate transmitter set (BCP-57)

BCP-52WAH

(30 functions)

Optional

Included

BCP-52WA

(25 functions)

Optional

BCP-51WH

(22 functions)

Optional

Included

BCP-51W

(17 functions)

Optional

Page 33

SECTION 5 : ADDITIONAL INFORMATION

Check the following before taking the BBB DigiBoard in for repairs.

D. TROUBLESHOOTING

PROBLEM

No speed or incorrect speed.

No cadence or incorrect cadence.

No heart rate or incorrect heart rate.

Transmitter will not pair.

Blank screen.

POSSIBLE CAUSES

• Magnet is not aligned or distance between

sensor and magnet is too big.

• Transmitter is not paired.

• Battery power is low.

• Wheel size is incorrect.

• Magnet is not aligned or distance between

sensor and magnet is too big.

• Transmitter is not paired.

• Battery power is low.

• Elastic belt is too loose.

• Contact areas are not moist.

• Transmitter is not paired.

• Battery power is low.

• Transmitter is not active.

• Battery power is low.

• Battery is empty.

• No battery installed.

Transmission platform: ANT+

Operation temperature: -10 °C to +60 °C / 14 °F to 140 °F.

Storage temperature: -20 °C to +70 °C / -4 °F to 158 °F

Main unit battery power: 3V Lithium battery: 1x (CR2032)

Dimensions and weight of main unit: 63 x 46 x 19.5mm / 33g

E. TECHNICAL SPECIFICATIONS

Batteries should be disposed in compliance with local regulations.

Page 34

Augusta Benelux BV

Rooseveltstraat 46

2321 BM

Leiden, The Netherlands

Tel (31)71 - 57 91 580

Fax (31)71 - 53 23 201

Email: [email protected]

BBBCYCLING.COM