S M AT V 1 1 2
D I G I T A L R E C E I V E R
User manual (UK)
Page 2
1. Connection of the receiver
2. Operating the receiver
Navigation:
BACK Exit/back botton in the menu
ENTER Activate menu, or open the sub menu
Menu UP
Menu DOWN
Å Moves cursor BACKWARDS
Æ Moves cursor FORWARDS
Input
Input
Loop
Audio
Video
Description
LNB input 950 - 2050 Mhz.
LNB output can be used, if more than one receiver is
connected, and using the same polarity and band (high/low).
This is only used within small installations.
Audio L/R output.
Video output.
Fan
PSU
2 fans make sure that the receiver does not overheat.
Plug and switch to turn off the 240V supply.
Å
Å
Input Loop Audio
L
R
Video
Power max. 45w
100-240V ~
50/60 Hz
CAUTION
RISK OF ELECTRICAL SHOCK
DO NOT OPEN
!
ã
Backside
RS232
CI
Conax /
Viaccess
Display
PSU
Description
Connection to PC, if the software need to be upgraded.
Cam reader for Common Interface modules.
Place the module with the serial number down.
Card reader for Conax and Viaccess cards.
Place the card with the yellow ic. down.
2 lines lcd display.
Plug and switch to turn off the 240V supply.
Front
EnterBack
Conax / Viaccess
RS232
DVB-CI
Page 3
3. In general
3.1 LNB
We do not recommend, that you connect more than one SMATV 112 to one
universal LNB. We recommend, that you use a quattro or twin LNB instead.
4. Display
When the receiver is not beeing programmed, it will show information about:
CHANNEL NAME
TEMPERATURE (how warm is the receiver)
PERIOD SINCE LAST RESTART
BIT ERROR RATE
NOTICE! If the display is ashing, the receiver has had a problem, and
has been restartet (via the Watchdog function).
5. Menu
Press ENTER to activate the menu, and then press ENTER again to open the
menu. In the display you will always be able to see, which possibility you have
to navigate. If p and q is shown in the display, then you are able to navigate up
and down in the menu. The same goes for t and u if shown, you can navigate
left and right in the menu.
5.1 1-LNB Setup
5.1.1 1-1-DiSEqC
With Æ you can choose between the following possibilities:
None = No DiSEqC
1 = DiSEqC input 1
2 = DiSEqC input 2
3 = DiSEqC input 3
4 = DiSEqC input 4
5.1.2. 1-2-LNB Type
Press ENTER and type in a value:
Universal - 9.75 GHz - 10.00 GHz - 10.05 GHz - 10.60 GHz - 10.75 GHz
DR1
UP:00000:20
29 C
BER:007%
p
q
1-1-DiSEqC
t 1 u
p
q
1-2-LNB Type
Universal u
Page 4
5.1.3. 1-3-LNB Power
ON turns on the power to the LNB
OFF turns off the power to the LNB
5.1.4. 1-4--22 KHz
Is only used if the 22KHz switch is mounted between the receiver and the LNB.
5.2 2-Tuner
In the TUNER menu, you can adjust the frequency on the transponder you wish
to receive.
5.2.1 2-1-Frequency
Press ENTER to open the menu of FREQUENCY adjustment.
1 gure UP
1 gure BACK
Å Moves cursor BACKWARDS
Æ Moves cursor FORWARDS
5.2.2 2-2-Polarity
Choose between horizontal/vertical polarity.
p
q
1-3-LNB Type
ON u
p
q
1-4-22 KHz
OFF u
p
q
2-1-Frequency
0 KHz
Å
Å
p
q
2-2-Polarity
H u
Page 5
5.2.3 2-3-Symbolrate
You can choose between the following symbolrates 22000, 22500, 24500, 26000,
27500, 27800 and 28000. If you need another specic symbolrate, you can type it
in by pressing ENTER.
5.3 3-Channel
When you press ENTER, the receiver will start searching for the programmes,
which match the values you have programmed into the receiver. When the
search is over, you have following possibilities:
5.3.1 3-1-Select channel
With t or u you can choose the channels you want to receive.
5.3.2 3-2-Audio Track
With t or u you can choose the audio track you want to receive.
ATTENTION: The receiver will only give information about the audio track, if the channel can be reached.
5.3.3 3-3-Subtitle
WIth t or u you can choose the subtitles you want to use.
ATTENTION: The receiver will only give information about subtitles, if the channel can be reached.
5.3.4 3-4-Program ID
If the receiver can not search the channel, you have the possibility to type in the
program ID, and search the channel this way.
p
q
2-3-Symbolrate
22000Ksy u
p
q
3-1-Select channel
CANAL + DAN u
p
q
3-2-Audio Track
Danish u
p
q
3-3-Subtitle
Danish u
p
q
3-4-Program ID
601
Page 6
The following values needs to be typed in:
Program ID - VPID - APID - PCR PID
5.3.5 3-5-VPID
The value is only typed in, if the receiver can not nd the channel under normal search.
5.3.6 3-6-APID
The value is only typed in, if the receiver can not nd the channel under normal search.
5.3.7 3-7-PCR PID
The value is only typed in, if the receiver can not nd the channel under normal search.
5.3.8 3-8-Subtitle PID
The value is only typed in, if the receiver can not show any subtitles.
The PID-information is available by the program distributor.
5.3.9 3-9-Aspect Adjust
In letterbox mode, the receiver converts a 16:9 picture to 4:3 picture.
p
q
3-5-VPID
0
p
q
3-6-APID
0
p
q
3-7-PCR PID
0
p
q
3-8-Subtitle PID
0
p
q
3-9-Aspect Adjust
t Letterbox
Page 7
5.4 4-Audio Output
The volume can be adjusted, so that it is the same as the other channels.
5.4.1 4-1-Volume Level
Press ENTER and type in a value.
5.5 5-Reset Receiver
Resets the receiver.
5.5.1 5-1-Conrm Reset
If you choose YES and then ENTER, the receiver will reset within a short while.
NOTICE! THIS WILL RESET ALL SETTINGS.
5.6 6-Fan Control
Choose when the fans must start (35°C is recommended).
5.6.1 6-1-Temperature
Choose between the dened values and press ENTER.
5.7 7-Smartcard Update
If the programme card is not updated, you can turn off the watchdog option. When
the card is updated, the receiver will turn on the wathdog option again automatically.
5.7.1 7-1-Watchdog
Choose between ON or OFF.
p
q
4-1-Volume LEvel
t %
p
q
5-1-Conrm Reset
NO u
p
q
6-1-Temperature
35 u
p
q
7-1-Watchdog
t ON
Page 8
5.8 8-Smartcard
Gives informations about the programme card.This information comes with the
CVBS signal.
5.9 9-Common Interface
Gives information about the card in the Common Interface slot. This information
comes with the CVBS signal.
5.10 10-Alarm Report
In this menu you can see the last 10 problems that has made the receiver restart.
5.11 11-Software Version
Shows the software version in the receiver.
5.12 12-Update Receiver
Press ENTER and the receiver will update the software from Sirius 5° East,
if it´s available.
© Kjaerulff 1 A/S 2003
Loading...