Digi X2EWIFI Users Guide
1 Verify Contents
Ethernet Cable
ConnectPort X2e Wi-Fi SE
Power Supply
2 Write Down the Serial Number
Write down the ConnectPort X2e Wi-Fi SE Serial Number:
00409D:
Model: ConnectPort X2e Wi-Fi SE
Part Number: 50X2E-Z1C-002-01
Serial Number: 00409D 50E9BB
Quick Start Guide
®
ConnectPort X2e Wi-Fi
Smart Energy
90001281_A
3 Connect Hardware
Connect the power supply
Connect the power supply
a
a
Startup Sequence - After connecting the power
b
supply, the Power LED will be solid green, the ZigBee
LED will be blinking green, and the Network LED (WAN)
will be blinking orange.
NOTE: Once the Wi-Fi conguration is complete, the
Network (WAN) LED will change from blinking orange
to solid green.
Button
Power
ZigBee
Network
(WAN)
NOTE: The serial number
is also the Ethernet
MAC address, which
can be used to identify
the device during the
installation process.
4 Congure your Device Using the Wi-Fi Interface
NOTE: If the ConnectPortX2e has already been congured
to connect to an access point, it will need to be set back to
factory defaults to use the following procedure. See the
troubleshooting section below to return the gateway back
to its initial state.
Enable Access Point mode on your device by pressing
a
the button.
Congure the Wi-Fi interface of your laptop to connect to
c
b
the ConnectPort X2e gateway’s access point.
(SSID) of the access point will be cpx2e-se-xxxxxxxxxx,
where xxxxxxxxxxxx is the serial number of the gateway.
Model: ConnectPort X2e Wi-Fi SE
Part Number: 50X2E-Z1C-002-01
Serial Number: 00409D50E9BB
The name
a
Go to your web browser, and enter the URL of the gateway:
cc
http://192.168.100.1
Navigate to Conguration > Wireless Wizard.
d
Follow the steps in the wizard to congure your device.
Once the conguration is complete, your device will connect
e
to your home access point and attempt to connect to
Smartlee. You can track its progress by observing the network
LED behavior. Once the connection to your access point and
gateway is connected to Smartlee, all the LED’s will be solid
green.
5 Online Installation
Browse to
www.livesmartlee.com
6 Troubleshooting
Power
Status
OFF
Solid green
ZigBee
Status
OFF
Blinking green (slow)
Blinking green (fast)
Solid green
and follow the step-by-step instructions to completion.
Description
No power
Device is powered
Description
Radio disabled
Searching for other ZigBee devices on the network
Establishing a Smart Energy network
Connected to a Smart Energy network
Network
Status
OFF
Blinking yellow (slow) Powered ON, no Wi-Fi link
Blinking yellow (fast)
Solid yellow
Blinking green (slow)
Blinking green (fast)
Solid green
Button - The button is intended for advanced conguration or as directed in the online setup. To restart Wi-Fi conguration, hold
the button down for 10 seconds to initiate a factory reset.
Description
Powered OFF
Wi-Fi link, no IP address
IP address assigned
Attempting a connection to Smartlee
Smartlee found, authenticating
Connected to Smartlee
Need Help? Call 1-877-693-7849 or visit www.digi.com/support.
7 Regulatory Information
For ConnectPort X2e Wi-Fi regulatory information and certications, please refer to the document at the following URL:
http://ftp1.digi.com/support/documentation/x2e_wifi_reg.htm
© 2012 Digi International, Inc.
Digi, Digi International, Inc., ConnectPort, iDigi, and the Digi and iDigi logos are trademarks or registered trademarks of Digi International, Inc., in the United States and other countries worldwide. All other trademarks are the property of their respective owners.
Loading...