Digi MIL-02F Installation Manual

MIL•02F

Fiber•MAU FDX

Full-Duplex Fiber Optic

Transceiver

FIBER•MAU

Model: MIL•02F

ETHERNET FULL-DUPLEX

10BASE-FL

TRANSCEIVER

Power Required: 12 VDC 200 ma

FCC PART 15 CLASS A

COMPLIANT

CX

TX RX

PWR

TX RX

Installation Guide

LINK

This guide includes the following information:

“Introduction” on page 2
“Installation” on page 2
“Configuration” on page 2
“DIP Switch” on page 2
“Jumper Settings” on page 3
“Diagnostic LEDs and Conditions Indicated” on page 3
“Legal” on page 4

With LinkSentry™

Ethernet/IEEE 802.3

Doc #: 90000108 Rev. A

Install Guide

Introduction

The MIL-02F is an Ethernet, multi-mode fiber transceiver that comes equipped
with diagnostic LEDs, an AUI male connector, and either an SC- or ST-type fiber
connector.

Installation

1. Connect the fiber cables: Attach the fiber cables from the fiber network cabling
to the fiber connectors on the MIL-02F.

2. Attach the 15-pin AUI connector from the MIL-02F to the DB-15 connector on
the device you wish to connect to.

3. Tighten the latch screws to secure the unit.

4. Restart the computer. The

Note:

If the

PWR

LED did not illuminate, reinstall the MIL-02F. If it still does not illuminate , contact

our technical support department.

LED illuminates.

PWR

Configuration

The MIL-02F comes with configurable options, which include a 2-position DIP
switch and a 3-pin jumper. The DIP switch is located on left-side of MIL-02F
(while facing the device), and the jumper is located inside the device. To open the
MIL-02F to access the 3-pin jumper:

1. For device's with ST-type connectors,u nscr ew the two hex nuts that secur e the
ST-type connectors.

2. Slide the top-half of the enclosure off, over the fiber connectors.

The jumper is located on right-hand side of the device (Figure 1).

DIP Switch

The Link Sentry feature on the MIL-02F is configured through the 2-position DIP
switch located on the side of the transceiver . Use a mechanical pencil to adjust the
DIP switches.

LinkSentry transmits link pulses only if the receive side of the link is seen. This
allows fault-tolerant transceivers and hubs to detect faulty cables or bad
equipment. Settings for the DIP switch includes:

Switch 1 LinkSentry disabled (Default) LinkSentry enabled
Switch 2 SQE disabled (Default) SQE enabled

Model: MIL-02F 2

Table 1: DIP Switch Settings

Up (off) Down (on)

Install Guide

Jumper Settings

The 3-pin jumper forces the device into half- or full-duplex operation.

• When pins 1 and 2 are covered, full-duplex is selected

• When pins 2 and 3 are covered, half-duplex is selected (default)

DIP Switch

3-Pin jumper
(with a jumper
block installed)

Figure 1.Inside the MIL-02F

Diagnostic LEDs and Conditions Indicated

• PWR (Power): Device is receiving power.

• TX (Transmit): Packets are being transmitted over the network.

• CX (Collision): Collisions are occurring on the network.

• RX (Receive): Packets are being received from the network.

• LINK (Link): The fiber optic link is good.

Model: MIL-02F 3

Legal

Regulatory Approvals

• FCC Class A

• UL 1950

• CSA 22 No. 950

• EN60950

• CE

– EN55022 Class B
– EN50082-1

Canadian EMI Notice

This Class A digital apparatus meets all the requirements of the Canadian Interference-Causing
Equipment Regulations.

Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le matériel
brouilleur du Canada.

European Notice

Products with the CE Marking comply with both the EMC Directive (89/336/EEC) and the Low Voltage
Directive (73/23/EEC) issued by the commission of the European Community. Compliance with these
directives implies conformity to the following European Norms:

• EN55022 (CISPR 22) - Radio Frequency Interference

• EN50082-1 (IEC801-2, IEC801-3, IEC801-4) - Electromagnetic Immunity

• EN60950 (IEC950) - Product Safety

Digi International warrants to the original consumer or purchaser that each of its
products, and all components thereof, will be free from defects in material and/or
workmanship for a period of five years from the original factory shipment date. Any
warranty hereunder is extended to the original consumer or purchaser and is not
assignable.

Digi makes no express or implied warranties including, but not limited to, any implied
warranty of merchantability or fitness for a particular purpose, except as expressly set
forth in this warranty. In no event shall Digi be liable for incidental or consequential
damages, costs, or expenses arising out of or in connection with the performance of the
product delivered hereunder. Digi will in no case cover damages arising out of the
product being used in a negligent fashion or manner.

To Contact Digi

For prompt response when calling for service information, have the following information ready:

• Product serial number and rev.

• Date of purchase

• Vendor or place of purchase

Reach Digi Technical Support at 408/744-2751
Or E-mail at “[e-mail]”

Address: 1299 Orleans Drive

Sunnyvale, CA 94089
Voice: 408/744-2775
Fax: [phone]
E-mail: [e-mail]

Five-Year Limited Warranty

Doc #: 90000108 Rev. A