Digi ConnectPort WAN, ConnectPort WAN VPN Quick Start Manual

Page 1
Install
Launch Wizard
ConnectPort WAN
ConnectPort WAN VPN
without integrated cellular module
© Digi International Inc., 2005. Digi, Digi International, the Digi logo, the Making Device Networking Easy logo, and Digi ConnectPort are trademarks or registered trademarks of Digi International, Inc. in the United States and other countries worldwide. All other trademarks are the property of their respective owners.
Quick Start Guide
What you will need
CONFIGURE
Digi Connectware
Manager CD
Antenna
sold separately
Power supply
Digi ConnectPort WAN
Insert CD
The LINK and ACT lights will blink when the connection is active.
Connect antenna to connector.
Connect Ethernet cable from any one of the Ethernet ports directly to laptop computer.
Connect power supply
Enter your Connectware server settings.
You may skip this page if you are not using Connectware Manager.
For more information on Connectware Manager, refer to the Connectware Manager Getting Started Guide.
1
From the web interface, go to the Configure Mobile settings and set the proper mobile settings supported by your SIM card. Click Apply
Under Management click Connections to verify your configuration has found an access point. To test your configuration and verify proper Ethernet to cellular routing, see the back of this guide.
2
Select a scenario that best describes your environment.
Follow the wizard to discover your device, set an IP address, and configure mobile settings.
After saving your configuration check "Log on to unit..." This will open the web interface where you must configure your mobile settings.
CONNECT
CELLULAR
Loopback plug
Under Hardware, click Install
Click Launch Wizard
If you have any difficulties, use the test scenario on the back of this guide to verify or troubleshoot your configuration.
1
2
3
4
5
6
Configure Your Cellular Settings
Install Wizard and Configure Device
Connect Hardware
2
7
Straight-through
cable
The ConnectPort WAN has DHCP server enabled by default. In order to discover your Digi device, make sure your host computer is setup to obtain IP addresses automatically. Also ensure all firewall software is temporarily disabled.
!
Software & Documentation
Software & Documentation
ConnectPort WAN
4
!
Warning: Do not over-tighten the antenna. Over-tightening may damage internal connections. Loosen antenna before adjusting antenna angles.
ConnectPort WAN
9-30VDC 1A MAX
LINK
ACT
STATUS
POWER
RESET
PRIMARY
ANTENNA
SECONDARY ANTENNA
SIGNAL STRENGTH
ConnectPort WAN
9-30VDC 1A MAX
LINK
ACT
STATUS
POWER
RESET
PRIMARY ANTENNA
SECONDARY ANTENNA
SIGNAL STRENGTH
Attach antenna to P23 connector next to the Primary antenna connector.
Silde antenna barrel end into PC Card Modem after it is seated on the board.
Unscrew cover and slide off. Unscrew access door and remove.
Verify SIM card is properly installed in PC card slot and slide PC Card Modem through access opening and seat on board.
ConnectPort WAN
9-30VDC 1A MAX
LINK
ACT
STATUS
POWER
RESET
PRIMARY ANTENNA
SECONDARY ANTENNA
SIGNAL STRENGTH
3
4
1
5
6
PN:(1P)
C
90000766_
Page 2
Test the Configuration
The following test scenario will prove proper routing of the cellular to Ethernet interface.
Cellular Network
Internet
Check your connection across the cell network by e
ntering a web site of your choice in the URL address bar of your browser and hit enter (e.g. www.digi.com). If your web page appears, you have verified cellular network communication
.
The test scenario requires assigning a static IP address to both the Digi ConnectPort WAN and your laptop or PC.
Connect the Digi ConnectPort WAN to your laptop or PC
Open your browser to the web interface of the Digi device by entering 192.168.1.1 in the URL address bar. Click System Information > Mobile. Verify that your device has appropriate signal strength and has obtained an IP address from the mobile network
1
2
3
4
Test Your Digi ConnectPort WAN:
The Digi ConnectPort WAN are configured by default with a static IP address of 192.168.1.1 and a DHCP server. The DHCP server will hand out leases beginning with 192.168.1.100. Configure your laptop or PC to obtain IP settings automatically and you will receive an IP address, default gateway and DNS server addresses from the Digi ConnectPort WAN
ConnectPort WAN
9-30VDC 1A MAX
LINK
ACT
STATUS
POWER
RESET
PRIMARY ANTENNA
SECONDARY ANTENNA
SIGNAL STRENGTH
Loading...