Page 1
0099001442-02
Model / Modelo:
28.71688
Sears Brands Management Corporation, Hoffman Estates, IL 60179 U.S.A.
Jump Starter and AC/DC/USB Power Source
Arrancador y CA / CC / USB fuente de alimentación
OPERATOR’S MANUAL /
MANUAL DEL USUARIO
CAUTION:
Read and follow all safety
rules and operating instructions
before every use of this product.
SAVE THESE INSTRUCTIONS.
ATENCIÓN:
Lea y siga todas las reglas
de seguridad e instrucciones de uso
antes de cada uso de este producto.
GUARDE ESTAS INSTRUCCIONES.
Page 2
DIEHARD® GARANTÍA TOTAL DE UN AÑO
Cuando se opere o maneje con las debidas precauciones de acuerdo a las instrucciones,
si el DieHard® falla en alguno de sus componentes de fabricación durante un año contados
a partir de la fecha de compra, regresarlo al autoservicio DieHard® en los estados unidos
para reemplazar el aparato sin costo alguno.
Esta garantía le otorga derechos legales especícos, así como otros derechos, que varían
de estado a estado.
Sears Brands Management Corporation, Hoffman Estates, IL 60179
PARA ASISTENCIA AL CLIENTE O REPUESTOS,
LLAME GRATIS AL 7 AM-5 PM CT
LUNES A VIERNES: 1-800-SEARS-64 (1-800-732-7764)
DIEHARD® ONE-YEAR FULL WARRANTY
When operated and maintained according to all supplied instructions, if this DieHard®
product fails due to a defect in material or workmanship within 1 year from the date of
purchase, return it to any DieHard® outlet in the United States for free replacement.
This warranty gives you specic legal rights, and you may also have other rights
which vary from state to state.
Sears Brands Management Corporation, Hoffman Estates, IL 60179
FOR CUSTOMER ASSISTANCE OR REPLACEMENT PARTS,
CALL 1-800-SEARS-64 (1-800-732-7764) TOLL-FREE
FROM 7 AM TO 5 PM CT.
THIS UNIT CONTAINS A SEALED, NON-SPILLABLE LEAD-ACID
BATTERY. MUST BE DISPOSED OF PROPERLY.
ESTA UNIDAD CONTIENE UNA BATERÍA SELLADA DE ÁCIDO-PLOMO
NO DERRAMABLE QUE DEBE DESECHARSE APROPIADAMENTE.
WARNING: Possible explosion hazard. Contact with battery acid may
cause severe burns and blindness. Keep out of reach of children.
ADVERTENCIA: Posible Riesgo de una explosión. El contacto
con una batería de ácido puede causar quemaduras y ceguera.
Manténgase alejado de los niños.
Page 3
CONTENTS
IMPORTANT SAFETY INSTRUCTIONS ................................................................................ 4
PERSONAL SAFETY PRECAUTIONS ..................................................................................4
FEATURES ............................................................................................................................. 5
CHARGING THE INTERNAL BATTERY OF THE PORTABLE POWER ................................ 5
USING THE PORTABLE POWER .......................................................................................... 6
MAINTENANCE AND CARE .................................................................................................. 8
TROUBLESHOOTING............................................................................................................ 8
BEFORE RETURNING FOR REPAIRS ................................................................................. 9
REPLACEMENT PARTS/ACCESSORIES ............................................................................. 9
CONTENIDOS
INSTRUCCIONES IMPORTANTES DE SEGURIDAD ......................................................... 10
PRECAUCIONES DE SEGURIDAD PERSONAL ................................................................ 10
CARACTERÍSTICAS .............................................................................................................11
CARGA DE LA BATERÍA INTERNA DE LA ENERGÍA PORTÁTIL ........................................11
CÓMO UTILIZAR LA ENERGÍA PORTÁTIL ......................................................................... 12
MANTENIMIENTO Y CUIDADO ........................................................................................... 15
LOCALIZACIÓN Y SOLUCIÓN DE PROBLEMAS ............................................................... 15
ANTES DE DEVOLVER A REPARACIONES ....................................................................... 16
REPUESTOS / ACCESORIOS ............................................................................................. 16
Page 4
• 4 •
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS.
WARNING – RISK OF EXPLOSIVE GASES
WORKING IN THE VICINITY OF A LEAD-ACID BATTERY IS DANGEROUS.
BATTERIES GENERATE EXPLOSIVE GASES DURING NORMAL OPERATION.
IT IS IMPORTANT THAT YOU FOLLOW THESE INSTRUCTIONS EACH TIME
YOU USE THE PORTABLE POWER.
To reduce the risk of battery explosion, follow these instructions and those published by
the battery manufacturer and the manufacturer of any equipment you intend to use in the
vicinity of a battery. Review cautionary markings on these products and on the engine.
WARNING: Pursuant to California Proposition
65, this product contains chemicals known to
the State of California to cause cancer and
birth defects or other reproductive harm.
Wash hands after handling.
• Keep out of reach of children.
• Do not disassemble the Portable Power.
Take it to a qualied service professional
if service or repair is required. Incorrect
assembly may result in re or electrical shock.
• Do not use the Portable Power to jump a
vehicle while charging the internal battery.
• Do not recharge the Portable Power with a
damaged extension cord.
• The Portable Power gets hot during
charging and must have proper ventilation.
• Do not set the Portable Power on ammable
materials, such as carpeting, upholstery,
paper, cardboard, etc.
• Place the Portable Power as far away from
the battery being jumped as the cables
will permit.
• Do not expose the Portable Power to rain
or snow.
• Never place the Portable Power directly
above battery being jumped.
• To prevent arcing, never allow the clamps to
touch together or to contact the same piece
of metal.
• Use of an attachment not recommended or
sold by the jump starter’s manufacturer may
result in damage to the unit or personal injury.
• Never operate the Portable Power if it is
damaged.
• If someone else uses the Portable Power,
ensure they are well informed on how to
use it safely, and have read and understood
the operating instructions.
• The Portable Power is NOT designed to be
installed as a replacement for a vehicle
battery.
• Use ONLY on vehicles, boats and garden
tractors powered with a 12V DC battery
system.
• If the engine fails to start after the
recommended number of attempts,
disconnect the unit and look for other
problems that may need to be corrected.
• Use the Portable Power for jump starting
lead-acid batteries ONLY. Do not use for dry
cell batteries that are commonly used with
home appliances.
PERSONAL SAFETY PRECAUTIONS
• Wear complete eye protection and
protective clothing when working near
lead-acid batteries. Always have someone
nearby for help.
• Have plenty of fresh water, soap and baking
soda nearby for use, in case battery acid
contacts your eyes, skin, or clothing. Wash
immediately with soap and water and seek
medical attention.
• If battery acid comes in contact with eyes,
ush eyes immediately for a minimum 10
minutes and get medical attention.
• Neutralize any acid spills thoroughly with
baking soda before attempting to clean up.
• Remove all personal metal items from your
body, such as rings, bracelets, necklaces
and watches. A battery can produce a short
circuit current high enough to weld a ring to
metal, causing a severe burn.
• Never smoke or allow a spark or ame in
the vicinity of the battery or engine.
Page 5
• 5 •
FEATURES
1. Jump start On/Off switch
2. Built-in light and switch
3. 110V AC household
power outlets (2)
4. 12V DC power outlets (2)
5. Cables with clamps
6. USB port ON/OFF button
7. USB ports (2)
8. Air compressor hose
9. Select battery % / inverter /
/ compressor button
10. Display LEDs
11. Digital display
12. Compressor ON/OFF button
1
2
3
5
7
6
9
8
10
4
11
12
CHARGING THE INTERNAL BATTERY OF THE PORTABLE POWER
IMPORTANT! CHARGE IMMEDIATELY
AFTER PURCHASE, AFTER EACH USE
AND EVERY 30 DAYS, TO KEEP THE
PORTABLE POWER’S INTERNAL
BATTERY FULLY CHARGED AND
PROLONG BATTERY LIFE.
CHECKING THE LEVEL OF THE
INTERNAL BATTERY
To check the internal battery’s charge
status, Press the Select button until the
Battery % LED lights. The Digital Display
will show the battery’s percent of charge.
Charge the internal battery if the display
shows it is under 100%.
NOTE: The internal battery’s percent of
charge is most accurate when the jump
starter has been disconnected from all
devices and charging sources for a few hours.
CHARGING THE INTERNAL BATTERY
Charge the internal battery for the Portable
Power using an extension cord (not included).
NOTE: Use of an improper extension cord
could result in a risk of re and electric shock.
1. To charge, ip the AC connector on
the back of the unit DOWN and plug in an
18 AWG or larger extension cord.
2. Plug the extension cord into a 120VAC
electrical wall outlet.
3. While the jump starter is charging, the
marching dashes will show on the
digital display. When the internal battery
is fully charged, the display will showioo.
Complete charging may take up to 72 hours.
4. When the internal battery is fully charged,
the charger will automatically go into
maintain mode and maintain the battery
at full charge without damaging it. When
in maintain mode, the Battery % LED will
pulse, as long as there is an AC cord
connected to the charging port.
5. Charge the jump starter as soon as
possible after use.
CHARGING THE INTERNAL BATTERY
WHILE DRIVING
You may also charge the internal battery
while driving, using a male-to-male
charger cable (part number 94500109 –
not included).
IMPORTANT: DO NOT CHARGE INTERNAL
BATTERY FOR MORE THAN 30 MINUTES
OR LEAVE THE BATTERY UNATTENDED. IT
COULD EXPLODE, CAUSING PROPERTY
DAMAGE OR PERSONAL INJURY.
1. Make sure the car is running.
2. Insert one end of the accessory cable into
the 12V DC power outlet.
3. Insert the other end of the accessory
cable into the vehicle’s accessory outlet
(lighter socket).
NOTE: The Battery % LED does not
operate during this method of charging.
Using this method to charge the battery
overrides the maintain mode and the battery
can be overcharged.
4. Monitor the progress of the charge by
pressing the Select button until the
Battery % LED lights. When the battery is
fully charged, disconnect the accessory
cable from the Portable Power, then from
the lighter socket of the vehicle.
NOTE: Completely disconnect the charger
cable when the engine is not running.
Page 6
• 6 •
USING THE PORTABLE POWER
DIGITAL DISPLAY
To check the jump starter’s internal battery
status, push the Select button. The display
will show the percent of charge of the
internal battery.
When connected to the vehicle with the Jump
Start ON/OFF switch in the OFF position, the
display shows the vehicle’s battery voltage.
When connected and in the ON position, the
display shows the equalized voltage between
the vehicle’s battery and internal battery.
JUMP STARTING A VEHICLE
IMPORTANT: Using the Jump Start feature
without a battery installed in the vehicle will
damage the vehicle’s electrical system.
1. Turn the ignition OFF.
2. Lay the DC cables away from any
fan blades, belts, pulleys and other
moving parts.
3. For a negative-ground vehicle (as in most
vehicles), connect the Portable Power’s
POSITIVE (RED) clamp to the POSITIVE
(POS, P, +) battery post. Next, connect
the NEGATIVE (BLACK) clamp to the
vehicle chassis or engine block, away
from the battery.
4. For a positive-ground vehicle, connect the
Portable Power’s NEGATIVE (BLACK)
clamp to the NEGATIVE (NEG, N, -)
battery post. Next, connect the POSITIVE
(RED) clamp to the vehicle chassis or
engine block away from the battery.
IMPORTANT: If you have connected the
clamps backwards, an audio alarm will
sound. DO NOT turn the ON/OFF switch to
the ON position. This could cause serious
damage to the jump starter or the vehicle.
Reverse the connections and the audio
alarm will stop.
5. Turn the switch to the ON position.
6. Crank the engine for no more than
8 seconds. If the engine does not start,
wait 2 minutes before cranking again.
7. After the engine starts, turn the switch to
the OFF position and remove the Portable
Power from the battery.
8. Charge the Portable Power.
USING THE WORK/EMERGENCY LIGHT
1. Position the jump starter on a at, stable
surface near the intended work area.
2. Ensure that the battery clamps are securely
clipped on the storage holders.
3. Press the light switch once.The jump
starter light will turn on and illuminate
your work area.
4. Press the light switch again. The light
will ash.
5. When nished, press the light switch again,
to turn off the light.
6. Charge the jump starter as soon as
possible after using the work light.
NOTE: The work/emergency light will
automatically shut off after 24 hours.
POWERING A 12V DC DEVICE
The Portable Power is a power source for all
12V DC accessories that are equipped with a
12V accessory plug. Use it for power outages
and on shing or camping trips. Estimated
usage time is listed in the following chart.
NOTE: Do not power a 12V device with the
Portable Power while charging the internal
battery.
NOTE: Make sure the device to be powered
is OFF before inserting the 12V DC accessory
plug into the 12V DC accessory outlet.
1. Ensure that the battery clamps are
securely clipped on the storage holders.
2. Open the protective cover of one of the
two DC power outlets on the front of the
jump starter.
3. Plug the 12V DC device into the DC power
outlet, and turn the 12V DC device on
(if required).
CAUTION: Do not use the Portable Power
to run appliances that draw more than
15A DC.
NOTE: Extended operation of a 12V DC
device may result in excessive battery drain.
Recharge the Portable Power immediately
after unplugging the 12V DC device.
12V DC ESTIMATED RUN-TIMES
APPLIANCE
TYPE
EST WATTAGE
ESTIMATED
RUN TIME
Cell phone 4 watts 54 hrs
Fluorescent
light
4 watts 54 hrs
Radios, fans 9 watts 24 hrs
Depth nder 9 watts 24 hrs
Camcorder 15 watts 14.4 hrs
Electrical tool 24 watts 9 hrs
Electric cooler 48 watts 4.5 hrs
Car vacuum,
air compressor
80 watts 2.7 hrs
NOTE: Actual time may vary. Times are based on the
internal battery being fully charged.
Page 7
• 7 •
USING THE USB PORT
The USB port provides up to 2.1A at 5V DC.
1. Ensure that the battery clamps are
securely clipped on the storage holders.
2. Plug the device into one of the two USB
ports on the front panel.
3. Press the USB port ON/OFF button.
4. Turn on the USB device.
5. When you are nished using the USB port,
press the button, to turn off.
6. Charge the jump starter as soon as
possible after using the USB port.
NOTE: To protect your electronic devices,
the USB will automatically shut off when the
internal battery’s charge is low.
USING THE AIR COMPRESSOR
WARNING. Read the instructions of the
product being inated before using the
compressor. Avoid overination; do not
exceed the manufacturer’s recommended
pressures. Do not leave the air compressor
unattended during use.
1. Remove the air compressor hose from the
storage compartment in the back of the
jump starter.
2. Connect the adapter to the valve stem
and close the thumb latch. If necessary,
use one of the additional adapters.
3. Press the Select button, and choose
Compressor.
4. To select the desired PSI, press
then press ON/OFF.
5. When the desired pressure is reached,
the compressor will turn off. Open the
thumb latch and remove the connector
from the valve stem.
6. Do not run for more than 10 minutes at a
time. Allow the jump starter to cool down
for 10 minutes before using again.
7. Wrap the compressor hose around the
cleats when it is not being used.
8. Allow unit to cool.
9. Recharge the unit before storing.
NOTE: To prevent overheating, the
compressor has built-in thermal protection
that will turn the compressor off before it
overheats. If the compressor shuts off, wait
a few minutes and it will automatically
restart when the compressor cools.
NOTE: The air compressor is rated for
100 PSI maximum.
ESTIMATED TIME FOR INFLATING
Vehicle Tires 13"-16" 5-8 minutes
Bike Tires 1-3 minutes
Sports Balls 30 seconds
These times are approximate. Use the air compressor
gauge to ensure the proper pressure has been reached.
Do not overinate.
USING THE INVERTER
It is important to know the continuous wattage
of the device you plan to use with the inverter.
The Portable Power must be used with
devices drawing 400 watts or less. If the
wattage is not marked on the device, use
only devices that draw less than 3.3 amps of
AC current.
Devices like TVs, fans or electric motors
require additional power to start (commonly
known as the “starting or peak power”). The
Portable Power can supply a momentary
surge in wattage; however even devices
rated less than the maximum 400 watts can
exceed the inverter’s surge capability and
cause an automatic overload shutdown.
Do not use the inverter with a product that
draws a higher wattage than the inverter can
provide, as this may cause damage to the
inverter and the product.
Make sure the device you are using is
compatible with a modied sine wave inverter.
CAUTION: Always run a test to establish
whether the inverter will operate a particular
piece of equipment or device.
In the event of a power overload, the inverter
is designed to automatically shut down. This
safety feature prevents damaging the
inverter while testing devices and equipment
with the 400-watt range.
If powering more than one device, start one
device at a time to avoid a power surge
and/or inverter overload. The surge load of
each device should not exceed the inverter’s
Continuous Operation wattage rate.
IMPORTANT: If you are using the power
inverter to operate any type of battery
charger, monitor the temperature of the
battery charger for about 10 minutes. If
the battery charger becomes abnormally
warm, disconnect it from the inverter
immediately.
You can use an extension cord from the
inverter to the device without signicantly
decreasing the power being generated by
the inverter. For best operating results, the
extension cord should be 16 AWG (1.31 mm2)
or larger and no longer than 50 feet.
Page 8
• 8 •
IMPORTANT: This inverter uses a modied
sine waveform, which is not quite the same
as power company electricity. For the
following devices, we strongly recommend
that you use caution and check the device’s
manual to make sure it is compatible with
modied sine waveform.
1. Switch mode power supplies
2. Linear power supplies
3. Class 2 transformers
4. Line lter capacitors
5. Shaded pole motors
6. Fan motors
7. Microwave ovens
8. Fluorescent and high-intensity lamps
(with a ballast)
9. Transformerless battery chargers
Using the inverter with any of these
devices may cause the device to run
warmer or overheat.
POWERING A 110V AC DEVICE
1. Ensure the battery clips are securely on
the storage holders.
2. Open the protective cover of the AC
power outlet on the front panel of the
Portable Power.
3. Make sure the 110V AC device to be
operated is turned OFF.
4. Plug the 110V AC device into the AC
power outlet and press the Select button,
to choose AC Inverter.
5. Turn the device on.
6. Charge the Instant Power as soon as
possible after each use.
RISK OF ELECTRIC SHOCK.
Incorrect operation of your inverter may
result in damage and personal injury. The
inverter output is 110V AC and can shock
or electrocute the same as any ordinary
household AC wall outlet.
NOTE: The maximum continuous load is
400 watts. Do not use the inverter with a
product that draws more than 400 watts, as
this may cause damage to the inverter and
the product. AN
MAINTENANCE AND CARE
• Clean the clamps and the case each time
you are nished using it.
• Recharge the unit once a month when not
in use.
• Store clamps on their support posts, to
ensure they do not come into contact with
any metallic surface.
• Never completely discharge the internal
battery.
TROUBLESHOOTING
PROBLEM POSSIBLE CAUSE REASON/SOLUTION
The Portable Power won’t
jump start my car.
The Jump Start switch is not
turned ON.
The clamps are not making
a good connection to the
battery.
The Portable Power’s battery
is not charged.
The vehicle’s battery is
defective.
Turn ON the Jump Start switch.
Check for poor connection to
battery and frame. Make sure
connection points are clean.
Check the battery charge
status by pressing the Select
button on the front of the
unit. See DIGITAL DISPLAY
section.
Have the battery checked.
Page 9
• 9 •
PROBLEM POSSIBLE CAUSE REASON/SOLUTION
The Portable Power won’t
power my 12V device.
The 12V device is not
turned on.
The Portable Power’s battery
is not charged.
The 12V device draws more
than 15A or has a short circuit.
Turn on the 12V device.
Check the battery charge
status by pressing the button
on the front of the unit. See
DIGITAL DISPLAY section.
Contact a qualied service
technician, to replace the fuse.
The battery in the Portable
Power won’t hold a charge.
The battery is bad (will not
accept a charge).
Replace the battery.
The Portable Power’s alarm
is on.
Connections are reversed. Disconnect the jump starter
and reverse the clamps.
The inverter is on, but the
display only shows err.
The jump starter battery is not
fully charged.
The device is drawing more
than 400W or has a short circuit.
Recharge the unit.
Use only devices that draw
less than 3.3 amps of AC
current.
BEFORE RETURNING FOR REPAIRS
If the above solutions do not eliminate the problem,
or for information about troubleshooting or replacement parts,
call toll-free from anywhere in the U.S.A.
1-800-732-7764
7:00 am to 5:00 pm CT, Monday through Friday
REPLACEMENT PARTS/ACCESSORIES
Male-to-male accessory cable ................................................................................ 94500109
Air compressor accessory kit (3 hose adapters)................................................. 0099000599
Loading...