Page 1
DICTATOR electromagnets are used in
combination with smoke detectors to keep
fire protection doors open.
The electromagnet with swivel head has
a distance tube which is welded vertically
onto a mounting plate.
The magnet is supplied with its head in a
straight position. To mount on the floor or
ceiling the head position can be altered
without having to interfere with any
electrical connections (see diagram on
the right).
The tube is available in three different
lengths. It can also be shortened to the
required length if necessary.
The mounting plate and tube are made of
grey laquered steel and the magnet is zinc
plated steel. The other parts are made of
light grey plastics (RAL 7037). An interrupter key is integrated in the lower part
of the tube.
DICTATOR magnets are equipped with
spark extinction diodes. In the event of
faulty connection, the integrated polarity
protection prevents the spark extinction
diode from being destroyed.
The EM GD 60 electromagnet has been
tested according to EN 1155 and
among others is included in the following
approvals: Z-6.5-1903, Z-6.5-1707.
Electromagnets
Electromagnet with
Swivel Head
For Installation on the Floor, Wall or Ceiling
Technical Data
© DICTATOR Technik GmbH • Gutenbergstr. 9 • 86356 Neusäß • Germany
Tel. +49(0)821-24673-0 • Fax +49(0)821-24673-90 • E-mail [email protected] • 1067
Electromagnet EM GD 60 EM GD 60 S
Voltage 24 VDC ±10 % 24 VDC ±10 %
Power consumption 67 mA (1.6 W) 79 mA (1.9 W)
Duty cycle 100 % 100 %
Operating temperature -20 °C to +60 °C -20 °C to +60 °C
Force 700 N 1000 N
Remanence / IP rating 0 N / IP 40 0 N / IP 40
Finish zinc-plated / powder coated RAL 9010
Page 07.031.00
Page 2
Electromagnets
ø 40
23
ø 60
ø 48
67
10
7
ø 96
88
"L"
"M"
88
70
68
7 x 10
3
40
ø 18
Arretierschraube
Installation
Dimensions
You can either fix the electromagnet with swivel head to the floor, ceiling or wall. If you
want to change the position of the head, you need to loosen the locking screw and turn
the head by 90°.
If you need to cut the distance tube, remove the head after loosening both grub screws
which fix the head to the tube. Then pull out the wires connected to the interruption key.
An anchorplate needs to be fixed to the door as a counterpart to the magnet. A choice
of different counter plates can be found later in this section.
The connection wires are inserted through an opening in the mounting plate. After the
magnet has been properly mounted and wired, both plastic covers are pushed from the
side over the mounting plate and clipped into position.
Please note:
It must be possible to release a fire protection door held open by an electromagnet with
a hand switch which is not hidden by the opened door. (DICTATOR hand switch part no.
040005, see diagram on the left).
Order Information
Page 07.032.00
Locking screw
Model Force Length "L" Height "M" Part no.
GD 60 S 175 700 N 175 mm 107 mm 040111
GD 60 S 175 oT (ohne Taster =
700N 175 mm 107 mm 040264
without interruptor key)
GD 60 S 175 S 1000 N 175 mm 107 mm 040164
GD 60 S 325 700 N 325 mm 257 mm 040112
GD 60 S 475 700N 475 mm 407 mm 040113
© DICTATOR Technik GmbH • Gutenbergstr. 9 • 86356 Neusäß • Germany
Tel. +49(0)821-24673-0 • Fax +49(0)821-24673-90 • E-mail [email protected] • 1067
Page 3
70
23
4 x ø 4,5
55
55
ø 60
82
Dimensions
Electromagnets
Electromagnet for Installing on the Wall
with Plastic Base and Interrupter Key
The electromagnet with the plastic base is an aesthetical unit. It permits to compensate for
larger distances between door and wall as with a normal electromagnet, without using
a distance tube. The electromagnet is furnished both with and without interrupter key in
the plastic base.
Fix the magnet to the wall and the anchor plate to the door. A selection of counter plates
can be found later in this section.
The connection wires are inserted through an opening at the bottom of the base plate.
Please note: It must be possible to release a fire protection door held open by an
electromagnet with a hand switch which is not hidden by the opened door. (DICTATOR
hand switch part no. 040005).
Order Information
© DICTATOR Technik GmbH • Gutenbergstr. 9 • 86356 Neusäß • Germany
Tel. +49(0)821-24673-0 • Fax +49(0)821-24673-90 • E-mail [email protected] • 1067
EM GD 60 K 70 electromagnet force 700 N part no. 040223
EM GD 60 K 70 without interrupter key force 700 N part no. 040224
EM GD 60 K70 electromagnet
with interrupter key
Part no. 040223
Page 07.033.00
Page 4
Electromagnets
Notes
Page 07.034.00
© DICTATOR Technik GmbH • Gutenbergstr. 9 • 86356 Neusäß • Germany
Tel. +49(0)821-24673-0 • Fax +49(0)821-24673-90 • E-mail [email protected] • 1067
Loading...