Page 1
MOUNT THE PANELS
Utility Knif e
INSTALLATION GUIDE
CVR-1
DiamondBackCovers.com / 800 935 4002
HD SE
Important installation informa tion
IMPORTANT!
Keep an eye out for these icons:
Normal install time
45 minutes
Tips to assist inst allation
Helpful Hints
Cap Clamps (4)
Bed-Rail
Edge Trim (4)
1/8" Hex Key
Gas
Springs (4)
Cab Panel
Tail Panel
Center Panel
TOOLS REQUIRED:
9/16"
Socket
7/ 16"
Socket
Ratchet Wrench
PARTS INCLUDED:
PRE-INSTALLATION NOTES:
It’s possible for one person to install a DiamondBack solo, but the
whole process, especially positioning the panels and adjusting the
lock rods, is much easier with t wo people.
If you are installing a cab guard or headache rack, you should
mount it prior to mounting your DiamondBack cover. Refer to its
installation guide for details.
Position the cover front to back so that the
leading edge of the closed cab panel lines up with
the outside edge of the center of the bulkhead.
6
Center the cover side to side on
the truck.
7
8
Tighten the cap clamps
with a 9/16" socket.
Road vibration can loosen your clamps. Retighten them after
100 miles. Check them every time you haul on top.
Repeat steps 3–4 for the
cab panel, starting this
time with the loop-shaped
hinge knuckle on the
passenger side.
5
Since the cover is
slightly tapered,
make sure the
arrow sticker on
the underside of
the center panel is
pointing toward
the tailgate.
Place the center panel across the
center of the bed, cheated slightly
toward the tailgate.
1
Lower the tail panel into the closed position.
4
1
2
Attach the tail panel by angling it 90° from the bed rails, sliding its
driver-side, loop-shaped hinge knuckle fully onto the corresponding
center-panel hinge pin, then dropping its passenger-side, C-shaped
hinge knuckle full y onto its corresponding pin.
3
FIRST
SECOND
90°
To avoid hinge damage, make sure the drop-on hinge
is fully mated before beginning to close the panel.
FU LLY M ATED
CONTIN UED ON REVERS E >
Loosely affix the center panel to the truck by finger-tightening a cap
clamp at each of the four interior corners of the underside of the
center panel.
2
Page 2
ADJUST THE LOCK RODS
ADJUST THE LOCK RODS
ADJUST THE LOCK RODS
ATTACH THE SAFETY CATCH & GAS SPRINGS
PREP FOR THE LOCK RODS
If you are also inst alling a Cross Bin, do so now. Refer
to the Cross Bin Installation Guide for details.
9
If a DiamondBack HD, unpin each of the four lock-rod guide -bracket slide plates
by using a 7/16" socket to move one of i ts bolts to the second, unoccupied slot.
If plastic ex tends beyond the bottom of the ver tical face of the metal
bed rails, trim a two-inch length of it flush with the bed rail’s bot tom
edge at each of the four points wher e a lock rod will pass under the rails.
10
Adjust the lock rods and retighten their set screws so that
A. with the lock handle in the open position, the rod tips clear
the bed rails,
B. with the handle in the closed position, the rod tips do not
strike the bed walls, and
C. the first bend in the rods points downward.
13
Loosen the se t screws on the
tailgate-panel lock-rod linkages.
1/8" hex key
12
Your panels should be hard to operate at first. After finishing
install below, leave the panels closed as much as possible for
3–4 days to break in the weather strip. After that period, you
should find that the panels open and close without difficulty.
Repeat steps 12 through 14 for the cab panel.
15
7/16" socket
7/16"
Using the access panels is easiest when
you press down as you open or close them.
For best weather protec tion, have a second person
press down on the cover while you adjus t the lock rods.
Position the lock rods tight
against the underside of
the bed rails so that they’ll
draw the panels down and
compress the weatherstrip. Tighten the rod guide
brackets with a 7/16"
socket.
14
Attach the three remaining gas springs
(barrel up, shaf t down).
18
If your truck has bed rail caps, affix the included
bulkhead weatherstrip. Refer to the Bulkhead
Prep Kit Installation Guide for det ails.
19
Adhesiv e cure time
24 hours
Leave the cover closed and locked for 24
hours to allow the weatherstrip adhesive,
which is pressure-sensitive, to fully cur e.
20
Fit the safety catch, which is hanging
from the driver side of the cab panel,
around the bot tom ball stud.
16
plastic
metal
Attach a gas spring to the ball studs
alongside the safety catch.
17
To avoid premature
failure of your gas
springs, attach them
barrel up, shaf t down.
If some of your gas springs have
heavier poundage printed on their
sides than others, use the stronger ones on the cab panel.
Peel the red adhesive backing from the edge trim pieces. Affix them
to the metal bed rail at the four points where a rod will pass underneath, the bottom curl of their j’s touching the bottom edge of the rail.
11
Affix the edge trim to the painted me tal only, behind the plastic
bed liner or bed rail cap, if present.
Using a tool to widen the curl of the ‘j’ can
make this step easier.
Step 11 is unnecessary on ’07–13 Silverados
and Sierras.
You may need to pull the plastic bed rail cap away from the metal bed rail to
provide enough clearance to get the edge trim on.
DiamondBackCovers.com
SEPTEMBER 2018
Loading...