How it Works
Diamond
Loading...
WR300NSI
Quick Install Guide
16 pgs1.05 Mb0
User Manual
31 pgs1.32 Mb0

Diamond WR300NSI User Manual

Download
Page 1
WR300NSI
Portable Wireless-N Repeater
Page 2
| WR300NSI User Manual
Page 2 of 31
Page 3
User Manual
Table of Contents
About the Device ........................................................................................................ 4
Minimum System Requirements ................................................................. 5
Package Contents ........................................................................................ 5
Device Overview .......................................................................................... 6
Front Panel ................................................................................................................ 6
Top Panel ................................................................................................................... 7
Bottom Panel ............................................................................................................ 8
Accessing the User Interface ...................................................................................... 9
Quick Connect .............................................................................................. 9
Setup ......................................................................................................... 10
Wireless ..................................................................................................... 11
Wireless Basic Settings ........................................................................................... 11
Wireless Security Settings ...................................................................................... 12
MAC Filter Settings .................................................................................................. 13
System ....................................................................................................... 15
Device Information ................................................................................................. 15
LAN Configuration ................................................................................................... 16
Configuration Settings ............................................................................................ 16
Firmware Upgrade .................................................................................................. 17
System Password
System Password .................................................................................................... 17
System PasswordSystem Password
Configuring the Device ............................................................................................. 19
Wireless Repeater ..................................................................................... 20
Wireless Access Point ................................................................................ 21
Wireless Bridge.......................................................................................... 22
Configure WR300NSI to Wireless Router via WPS ................................................. 24
FCC Notice ................................................................................................................. 29
Page 3 of 31
Page 4
| WR300NSI User Manual
About the Device
Diamond Multimedia WR300NSI is a Wall-plugged 300Mbps Wireless-N Repeater, which supports wireless 8 0 2.11 b /g/n, a nd one 10/100 Base -T Ethernet port.
RRRReeeeppppeeeeaaaatttt aaaannnnd E WR300NSI supports robust 802.11n technology with up to 300Mbps data transfer rate. The extender can take an existing 802.11n wireless signal, repeat and extend it to a longer range where it is too far away for the router or access point to reach. It eliminates the cable wires while providing the same reliable network connection. It can repeat and extend the wireless signal from virtually any 802.11n wireless router or access point that is launched on the market. It is backwards compatible with the
802.11b/g router or access point.
MMMMaaaakkkkeeee WWWWiiiired The extender is equipped with 1 x 10/100M Auto MDI/MDIX LAN port that can be used to connect to an existing wired network to serve as a wireless interface. It can also be used to configure the extender via its web-based GUI, or upgrade the firmware.
MMMMIIIIMMMMO The device is designed with MIMO technology, which successfully reduces “dead spot”, and extends network coverage within a home or in the building.
Advanced Security
WR300NSI features with 64/128-bit WEP encryption and WIFI Protected Access (WPA), WPA2 to ensure the network security and prevent unauthorized access to you network.
PPPPor
orttttaaaabbbblllleeee wwwwiiiitttthhhhoooouuuut
oror
The device is easy to setup. It is portable with no need of any external power adaptor. It comes with the embedded power supply and power plug, so that users can just plug the device into a power socket.
d Exxxxtttteeeennnndddd tttthe
d Ed E
red NNNNeeeettttwwwwork
red red
O TTTTeeeecccchhhhnnnnology
O O
ology
ologyology
t tttthe
t t
he WWWWiiiiFFFFiiii NNNNeeeettttwwwwork
hehe
ork WWWWiiiiFi
orkork
Fi RRRReeeeaaaaddddyyyy
FiFi
he NNNNeeeeeeeed of
he he
d of EEEExtern
d of d of
ork
orkork
xternaaaallll PPPPoooowwwwer
xternxtern
er SSSSuuuuppppppppllllyyyy
erer
Page 4 of 31
Page 5
User Manual
Minimum System Requirements
Your computer must meet the following minimum requirements.
Any operating system can be used Web Browser 233MHz processor Ethernet network adapter Or Wireless network adapter
Package Contents
Package contents are listed below. For any missing items, please contact your dealer immediately. Product contents may vary for different models.
WR300NSI Ethernet cable Easy Start Guide Resource CD
Page 5 of 31
Page 6
| WR300NSI User Manual
Device Overview
Page 6 of 31
Front Panel
Page 7
User Manual
LABEL
STATE
DESCRIPTION
LED RRSI
3 BARS Connected 95% and above RSSI (Excellent)
2 BARS Connected 55-94% RSSI (Recommended)
1 BAR Connected 10-54% RSSI (Weak)
Top Panel
LABEL DESCRIPTION
WPS BUTTON Connect WR300NSI to any WPS capable devices
Page 7 of 31
Page 8
| WR300NSI User Manual
Bottom Panel
LABEL DESCRIPTION
RESET Press the Reset button for 5 seconds to restore the device to default factory settings
ETHERNET PORT Connect to computers/Ethernet devices
Page 8 of 31
Page 9
Accessing the User Interface
To access the User Interface open a Web browser (Ex: Internet Explorer, Firefox or G.chrome) and type
http://10.0.10.254
in the address bar and press enter.
User Manual
Quick Connect
Press
Quick Connect
icon to scan for available wireless within the area.
Page 9 of 31
Page 10
Setup
| WR300NSI User Manual
Mode of Operation
Mode of Operation
Mode of OperationMode of Operation
Repeater
Repeater
RepeaterRepeater Configure your device as a wireless repeater to extend the wireless coverage of your wireless router.
Access Point
Access Point
Access PointAccess Point Configure your device as an access point to provide wireless network accessibility to a non wireless network
Bridge
Bridge
BridgeBridge Configure your device as a Bridge to act as wireless client to your network device. In this mode you can convert wireless signal to wired Ethernet for devices not supporting wireless connections.
SSID
SSID
SSIDSSID
Here you can set the name of your wireless network. Select the option Disable on Broadcast SSID allow you to hide the wireless network name.
Security Mode
Security Mode
Security ModeSecurity Mode
Select from different encryption type on the list to be used to provide security to your wireless network from unauthorized users. Select
WEP
WEP
WEPWEP HEX 64bit – uses 10 characters length of password from A-F and numbers from 0-9 128bit- uses 26 characters length of password from A-F and numbers from 0-9
Page 10 of 31
Page 11
User Manual
ASCII 64bit – uses 5 characters alpha numeric password (A-Z and 0-9) 128bit – uses 13 characters length of password from (A-Z and 0-9)
WPA
WPA
WPA WPA Uses strong encryption, some legacy devices may not be able to associate with this type of encryption
WPA2
WPA2
WPA2WPA2 Use this encryption for best security, some legacy device may not associate with this type of encryption
WPA/WPA2 PSK
WPA/WPA2 PSK
WPA/WPA2 PSKWPA/WPA2 PSK Use a balance of strong security and best compatibility for new and legacy devices.
Wireless
Wireless Basic Settings
Enable Wireless
Enable Wireless
Enable WirelessEnable Wireless Enable or Disable wireless capability
Broadcast SSID
Broadcast SSID
Broadcast SSIDBroadcast SSID Set option to disable to hide your wireless network (Enable by default)
Page 11 of 31
Page 12
| WR300NSI User Manual
SSID
SSID
SSIDSSID Here you can enter the name of your wifi network
Wireless Mode
Wireless Mode
Wireless ModeWireless Mode This option allows you to select the type of wireless standard you want to allow to connect to your wireless network.
Channe
Channellll
ChanneChanne Change your wireless channel when you are getting poor reception. Choose the least channel used in your area for better performance (Only applicable for AP mode)
Channel Bandwidth
Channel Bandwidth
Channel BandwidthChannel Bandwidth Here you can set your Channel Bandwidth to 20MHz and 20/40MHz(Auto) HT Da
HT Data Rate and HT Guard Interval
ta Rate and HT Guard Interval
HT DaHT Da
ta Rate and HT Guard Interval ta Rate and HT Guard Interval
These options are recommended to be set to Auto for maximum efficiency.
Wireless Security Settings
Security Mode
Security Mode
Security ModeSecurity Mode Select the type of encryption you want for your wireless network
WPS
WPS
WPS WPS Set this option to enable or disable WPS (Wifi Protected Setup) feature on this device
Enrollee PIN
Enrollee PIN
Enrollee PINEnrollee PIN Enter this PIN to wireless client that will be connecting to WR300NSI repeater to automatically configure the wireless device.
Registrar PIN
Registrar PIN
Registrar PINRegistrar PIN
Page 12 of 31
Page 13
User Manual
Here you can enter the WPS-PIN of wireless clients and click apply for the WR300NSI to allow access and configure your wireless client device automatically
Note: WPS will work only for WPA-PSK, WPA2-PSK and WPA/WPA2 encryption. Wireless client should support WPS feature to use this option.
MAC Filter Settings
This feature will provide additional protection to your wireless network. It allows or denies wireless clients from accessing through the WR300NSI with the use of the MAC address which is unique for every network devices.
Policy
Policy
PolicyPolicy
Dis
Disable
able
DisDis
ableable Use this option to disable or disregard the list of MAC address from blocking or allowing access to the wireless network.
Allow
Allow
AllowAllow Allow the list of MAC address from accessing the wireless network
Deny
Deny
DenyDeny Deny the list of MAC address form accessing the wireless network
Page 13 of 31
Page 14
| WR300NSI User Manual
MAC Address
MAC Address
MAC AddressMAC Address Type the MAC address of the wireless client here and press to add on the list.
Removing MAC address from the list
Removing MAC address from the list
Removing MAC address from the listRemoving MAC address from the list Press this icon to remove the MAC address from the list
Where can I find the MAC address of my wire
Where can I find the MAC address of my wireless client?
Where can I find the MAC address of my wireWhere can I find the MAC address of my wire On the Command Prompt type
ipconfig/all
less client?
less client?less client?
to show all the network adapter(s) that are
available.
Page 14 of 31
Page 15
System
Device Information
User Manual
Firmware Version
Firmware Version
Firmware VersionFirmware Version Shows the current firmware version of the device
Build Date
Build Date
Build DateBuild Date Shows the date when firmware is created
Serial Number
Serial Number
Serial NumberSerial Number Shows the device’s serial no
ETH/Bridge and Wireless MAC address
ETH/Bridge and Wireless MAC address
ETH/Bridge and Wireless MAC addressETH/Bridge and Wireless MAC address Shows the MAC address of the different Interface
Wireless Status
Wireless Status
Wireless StatusWireless Status Shows the wireless device’s wireless status
Page 15 of 31
Page 16
| WR300NSI User Manual
LAN Configuration
Device IP address
Device IP address
Device IP addressDevice IP address Shows the device’s current IP address
Note:
Note: Change this IP address if you are using two WR300NSI on the same network to
Note:Note: avoid IP address conflict within your network. You may configure the 2nd unit with IP address ex: 10.0.10.253
Configuration Settings
Backup S
Backup Settings
Backup SBackup S Allow you to save the current configuration of WR300NSI. Default file name for the backup file will be “
ettings
ettingsettings
RT2880_Settings.dat”.
Click Apply
Apply to start saving your configuration.
ApplyApply
Page 16 of 31
Page 17
User Manual
Update
Update
UpdateUpdate Here you can load the saved configuration of your WR300NSI. Click browse and load the saved settings by clicking on the apply button.
Restore
Restore
RestoreRestore Click on the apply button to reset the unit back to its factory settings. Unsaved information will be lost.
Firmware Upgrade
This option allows you to update the firmware of your device for future changes and enhancement.
Updating the firmware
Updating the firmware
Updating the firmwareUpdating the firmware
a. Connect an Ethernet cable between WR300NSI and computer b. Open web browser and type http://10.0.10.254 to access the user interface c. Click on Setup and select firmware under the sub menu d. Click on the Browse
click Apply
Apply to start the update.
ApplyApply
Note:
Note: It is recommended to only use firmware which is officially release by Diamond Multimedia, Using
Note:Note: third party firmware will void the warranty of the device.
System Password
System Password
System PasswordSystem Password
Set a password on web user interface to prevent other users from getting access to the web UI and avoid unwanted changes from your settings.
Browse button and locate and open the firmware for WR300NSI and
BrowseBrowse
Page 17 of 31
Page 18
| WR300NSI User Manual
System Password
System Password
System PasswordSystem Password Type your password and click on apply to activate this feature. To disable, simply remove the password and click apply to save your settings.
Note:
Note: forgotten password will not be recovered. Reset the device pressing the reset button found beside
Note:Note: the Ethernet port of WR300NSI.
Page 18 of 31
Page 19
User Manual
Configuring the Device
Placement of the Wireless Repeater is crucial to get the best possible results for extending your existing wireless signal. It is ideal for the wireless repeater to be placed in a location where it can receive good wireless signal from the wireless router/AP so as to avoid disconnection and packet loss.
LED smart indicator determines the signal strength from your wireless router.
Wireless reception and throughput may vary according to the number of wireless clients that are in use at the same time, other nearby wireless devices, structure type, building materials and other interference present.
Page 19 of 31
Page 20
| WR300NSI User Manual
Wireless Repeater
a. Plug your WR300NSI to a power outlet, switch it ON and connect the Ethernet
cable between your WR300NSI and Computer
b. Launch web browser and you will be directed to the User Interface (In case it does
not open type 10.0.10.254 and hit enter)
Select your SSID (wireless network/wifi name) from the list and click connect
c.
Page 20 of 31
Page 21
d. Type the password for the wireless network of your router and click apply. The
WR300NSI will reboot and will redirect to the user interface with the following status.
e. Disconnect the Ethernet cable from WR300NSI and computer then place the
device at the location, where it can get sufficient reception from your wireless router.
SETUP DIAGRAM (REPEATER)
User Manual
Wireless Access Point
Setup your WR300NSI as an access point to provide wireless network to router that doesn’t have wireless feature.
Page 21 of 31
Page 22
| WR300NSI User Manual
a. Plug your WR300NSI to a power outlet b. Connect an Ethernet cable between the WR300NSI and Computer c. Launch web browser and you will be directed to the User Interface
d. Go to Setup, set Mode of Operation to Access Point . Type the name of your wireless network under SSID f. Type the password of the wireless network and click apply g. Connect the WR300NSI to router’s LAN port after the settings have been saved.
SETUP DIAGRAM (AP)
Wireless Bridge
Connect wired devices to your wireless network by connecting an Ethernet cable from a wired device, such as a Desktop PC, Game Console or Internet-ready LCD TV, to the Ethernet port of the WL556E.
Page 22 of 31
Page 23
a. Plug in and turn ON your WR300NSI b. Connect the Ethernet cable between your computer and WR300NSI c. Launch a web browser. You will be directed to the user interface
User Manual
d. Click on Setup e. Type the name of your wireless network for the SSID
Setup and set Mode of Operation to Bridge
SetupSetup
Bridge
BridgeBridge
SSID
SSIDSSID
f. Enter the channel and password of your wireless network and click apply
Note: SSID, Security mode, password/passphrase and wireless channel must match to router’s wireless settings.
SETUP DIAGRAM
SETUP DIAGRAM (BRIDGE)
SETUP DIAGRAMSETUP DIAGRAM
(BRIDGE)
(BRIDGE)(BRIDGE)
Modem
WR300NSI
Wireless Router
WPS
WPS or Wifi Protected Setup makes it easier for you to connect your WR300NSI to your wireless router and WR300NSI to your wireless devices with a push of a button. (WPS
Page 23 of 31
Page 24
| WR300NSI User Manual
feature must be enabled and must be supported on the wireless router and wireless devices that will be connected to WR300NSI)
Configure WR300NSI to Wireless Router via WPS
a. Press the WPS button of WR300NSI for 5 seconds b. Press the WPS button on your router for 2 seconds within 2 minutes time
Page 24 of 31
Page 25
User Manual
Safety Precautions
Do not open, service, or change any component. Only qualified technical specialists are allowed to service the equipment. Observe safety precautions to avoid electric shock Check voltage before connecting to the power supply. Connecting to the wrong
voltage will damage the equipment.
Page 25 of 31
Page 26
| WR300NSI User Manual
Technical Support
Diamond Technical Support staff is here to help resolve any issues that you may be experiencing. Prior to contacting technical support please make sure you have the following information available.
1. Model #: (Printed on the bar code, located on the box)
2. Installation CD Version: (printed on the CD label)
3. The version of Windows that your system is running.
4. The manufacturer and model # of your computer.
5. CPU type and speed (example: Intel Pentium4 2.4GHZ)
6. A complete description of the problem that you are experiencing including any
steps that you have taken to try to resolve the issue.
Technical Support Options Free Telephone Support
818-357-5165 (long distance rates may apply) Mon - Fri, 8 - 4:30 PST http://www.diamondmm.com
Page 26 of 31
Page 27
User Manual
SHIPPING Starting June 1st 2009 Diamond Multimedia will pay for shipping cost from Diamond back to US and Canadian customers provided the product is indeed under warranty and there is no damage caused by improper installation or modification of the merchandise. Customers located outside of the United States and Canada or using military addresses (APO,etc) will be required to pay for return shipping. Average shipping times range from 5 to 10 days, depending on actual shipment destination. Shipments made outside the US may take longer to deliver.
Diamond Multimedia reserves the right to claim for shipping fees along with service charges for any product that is returned incomplete or not under warranty. Return Authorization ( RMA ) is required for all warranty return products.
ONE YEAR LIMITED WARRANTY The warranty described below is extended only to the original buyer and is not transferable. Diamond warrants to the original purchaser of the hardware product, that the product is free from defects in materials or workmanship under normal use and service for a period of one (1) year from the date of purchase. All cables and accessories provided with a Diamond product are warranted to be free from defects in materials or workmanship under normal use and service for a period of for (90) ninety days from date of purchase.
Diamond’s sole obligation under this warranty shall be, at Diamond’s option, to: (I) repair the defective product or parts; (II) deliver to customer an equivalent product or part to replace the defective product. When a product or part is replaced or exchanged, that item becomes the customer’s property and the replaced or exchanged item becomes Diamond’s property. When a refund or replacement product is given, the defective product becomes Diamond’s property. Replacement parts or products may be new or include serviceable used parts with at least the same functional equivalence to the original product. If, at the time of repair, a product is "out of warranty" or within the last ninety (90) days of the warranty period, Diamond warrants any repair for ninety (90) days. All software provided is subject to the terms of the associated software end-user license agreement.
WARRANTY EXCLUSIONS AND LIMITATIONS TO BE ELIGIBLE FOR THIS WARRANTY, YOU NEED TO PROVIDE THE ORIGINAL SALES RECEIPT SHOWING THE DATE OF PURCHASE OF THE PRODUCT. DIAMOND MAY REQUEST THE ORIGINAL SALES RECEIPT OR A COPY AS PROOF OF THE DATE OF PURCHASE.
Diamond does not warrant third party products which Diamond distributes "AS IS" unless otherwise specified. Third party products may be warranted by the third party.
Diamond makes no warranty or representation that: (I) the operation of the product will be uninterrupted or error free; (II) defects in the product will be corrected; or (III) that the product will meet Customer’s requirements or work in combination with any hardware or software provided by third parties.
TO THE FULLEST EXTENT ALLOWED BY LAW, THE WARRANTIES, REMEDIES AND LIMITATIONS CONTAINED HEREIN ARE EXCLUSIVE AND ARE IN LIEU OF ALL OTHER WARRANTIES, TERMS OR CONDITIONS, EXPRESS OR IMPLIED, EITHER IN FACT OR BY OPERATION OF LAW, STATUTORY OR OTHERWISE, INCLUDING WITHOUT LIMITATION, WARRANTIES, TERMS OR CONDITIONS OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, QUALITY, CORRESPONDENCE WITH DESCRIPTION AND NON-INFRINGEMENT, ALL OF WHICH ARE EXPRESSLY DISCLAIMED.
DIAMOND WILL NOT BE LIABLE UNDER THIS WARRANTY IF ITS TESTING AND EXAMINATION DISCLOSE THAT THE ALLEGED DEFECT OR MALFUNCTION IN THE PRODUCT OR SOFTWARE DOES NOT EXIST OR WAS CAUSED BY CUSTOMER’S OR ANY THIRD PARTY’S MISUSE, NEGLECT, IMPROPER INSTALLATION OR TESTING, UNAUTHORIZED ATTEMPTS TO OPEN, REPAIR OR MODIFY THE PRODUCT OR SOFTWARE, OR ANY OTHER CAUSE BEYOND THE RANGE OF THE INTENDED USE, OR BY ACCIDENT, FIRE, LIGHTNING, OTHER HAZARDS, OR ACTS OF GOD. THIS WARRANTY WILL NOT APPLY TO PRODUCTS USED FOR NUCLEAR RELATED, WEAPONS RELATED, MEDICAL OR LIFE SAVING PURPOSES.
Page 27 of 31
Page 28
TO THE FULLEST EXTENT ALLOWED BY LAW, DIAMOND ALSO EXCLUDES FOR ITSELF AND ITS SUPPLIERS ANY LIABILITY, WHETHER BASED IN CONTRACT OR TORT (INCLUDING NEGLIGENCE), FOR INCIDENTAL, CONSEQUENTIAL, INDIRECT, SPECIAL OR PUNITIVE DAMAGES OF ANY KIND, OR FOR LOSS OF REVENUE OR PROFITS, LOSS OF BUSINESS, LOSS OF INFORMATION OR DATA, OR OTHER FINANCIAL LOSS ARISING OUT OF OR IN CONNECTION WITH THE SALE, INSTALLATION, MAINTENANCE, USE, PERFORMANCE, FAILURE, OR INTERRUPTION OF ITS PRODUCTS, EVEN IF DIAMOND, ITS SUPPLIERS OR ITS RESELLER HAS BEEN ADVISED OF THE POSSIBLITY OF SUCH DAMAGES. DIAMOND’S SOLE LIABILITY WITH RESPECT TO ITS PRODUCT IS LIMITED TO REPAIR OR REPLACEMENT OF THE PRODUCT, AT DIAMOND ’S OPTION. THIS DISCLAIMER OF LIABILITY FOR DAMAGES WILL NOT BE AFFECTED IF ANY REMEDY PROVIDED HEREIN SHALL FAIL FOR ESSENTIAL PURPOSE.
DISCLAIMER: Some jurisdictions may not allow the exclusion or limitation of incidental or consequential damages for products supplied to consumers, or the limitation of liability for personal injury, so the foregoing limitations and exclusions may not apply or may be limited in their application to you. When implied warranties are not allowed to be excluded in their entirety, they will be limited to the duration of the applicable written warranty. This warranty gives you specific legal rights that may vary depending on the law of the applicable jurisdiction.
OBTAINING WARRANTY SERVICE: Please review the "help" resources referred to in your products accompanying documentation before seeking warranty service. If the product is still not functioning properly after making use of these resources, please access the support page at http://www.diamondmm.com/support.php for warranty instructions and services. Some additional charges may apply for phone support.
| WR300NSI User Manual
Page 28 of 31
Page 29
User Manual
FCC Notice
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio or television technician for help.
Modifications
Modifications
ModificationsModifications
The FCC requires the user to be notified that any changes or modifications made to this device that are not
expressly approved by Diamond Multimedia could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC rules.
This device complies with Part 15 of the FCC rules.
This device complies with Part 15 of the FCC rules.This device complies with Part 15 of the FCC rules.
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause
undesired operation.
Exposure Information to Radio Frequency Energy
Exposure Information to Radio Frequency Energy
Exposure Information to Radio Frequency EnergyExposure Information to Radio Frequency Energy
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with minimum distance of 20 cm between the radiator and
your body.
Page 29 of 31
Page 30
| WR300NSI User Manual
© Copyright 2010 All rights reserved.
No part of this document may be reproduced, republished, or retransmitted in any form or by any means whatsoever, whether electronically or mechanically, including, but not limited to, by way of photocopying, recording, information recording, or through retrieval systems without the express written permission. We reserve the right to revise this document at any time without the obligation to notify any person and/or entity. All other company or product names mentioned are used for identification purposes only and may be trademarks of their respective owners.
LIMITATION OF LIABILITY AND DAMAGES
THE PRODUCT AND THE SOFTWARES WITHIN ARE PROVIDED "AS IS," BASIS. THE MANUFACTURER AND MANUFACTURER’S RESELLERS (COLLECTIVELY REFERRED TO AS “THE SELLERS”) DISCLAIM ALL WARRANTIES, EXPRESS, IMPLIED OR STATUTORY, INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF NON­INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, OR ANY WARRANTIES ARISING FROM COURSE OF DEALING, COURSE OF PERFORMANCE, OR USAGE OF TRADE. IN NO EVENT WILL THE SELLERS BE LIABLE FOR DAMAGES OR LOSS, INCLUDING BUT NOT LIMITED TO DIRECT, INDIRECT, SPECIAL WILLFUL, PUNITIVE, INCIDENTAL, EXEMPLARY, OR CONSEQUENTIAL, DAMAGES, DAMAGES FOR LOSS OF BUSINESS PROFITS, OR DAMAGES FOR LOSS OF BUSINESS OF ANY CUSTOMER OR ANY THIRD PARTY ARISING OUT OF THE USE OR THE INABILITY TO USE THE PRODUCT OR THE SOFTWARES, INCLUDING BUT NOT LIMITED TO THOSE RESULTING FROM DEFECTS IN THE PRODUCT OR SOFTWARE OR DOCUMENTATION, OR LOSS OR INACCURACY OF DATA OF ANY KIND, WHETHER BASED ON CONTRACT, TORT OR ANY OTHER LEGAL THEORY, EVEN IF THE PARTIES HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. THE ENTIRE RISK AS TO THE RESULTS AND PERFORMANCE OF THE PRODUCT OR ITS SOFTWARE IS ASSUMED BY CUSTOMER. BECAUSE SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABLITY FOR DAMAGES, THE ABOVE LIMITATION MAY NOT APPLY TO THE PARTIES. IN NO EVENT WILL THE SELLERS’ TOTAL CUMULATIVE LIABILITY OF EACH AND EVERY KIND IN RELATION TO THE PRODUCT OR ITS SOFTWARE EXCEED THE AMOUNT PAID BY CUSTOMER FOR THE PRODUCT.
Page 30 of 31
Page 31
User Manual
Page 31 of 31
Loading...
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use