Diamond Vision DVDV805-03, Vision DVDV805-04 Operation Manual
DVD / MP3 / CD PLAYER
LECTEUR DVD / MP3 / CD
DVDV805-03
DVDV805-04
mp3
THIS INSTRUCTION BOOK MAY CONTAIN ERRORS AND OMISSIONS.
DESIGN AND SPECIFICATION ARE SUBJECT TO CHANGE WITHOUT NOTICE.
CE LIVRET D’INSTRUCTIONS PEUT CONTENIR DES ERREURS ET DES OMISSIONS. LE
CONCEPT ET LES CARACTÉRISTIQUES SONT SUJETS À CHANGEMENT SANS PRÉAVIS.
OPERATION MANUAL
MANUEL DE FONCTIONNEMENT
2
IMPORTANT
Since CD circuitry may cause interference with other radio tuners nearby, switch this recorder
off when not in use or move it away from an affected radio tuner.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesirable operation.
Warning: Changes or modifications to this unit not expressly approved by the party responsible
for compliance could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates
uses and can radiate radio frequency energy and, if not installed and used in accordance with
these instructions, may cause harmful interference to radio communications. There is no
guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
• Consult the dealer or an experienced radio / TV technician for help.
SAFETY CERTIFICATION
This CD player is made and tested to meet safety standards of the FCC, requirements and
compliance with safety performance of the U.S. Department of Health and Human Services,
and also with FDA Radiation Performance Standards 21 CFR Subchapter J.
WARNING
To prevent fire or shock hazard, do not expose this appliance to rain or moisture.
The apparatus should not be exposed to dripping or splashing and that no objects filled with liquids, such
as vases, shall be placed on the apparatus.
The ventillation should not be impeded by covering the ventilation openings with items, such as
newspapers, table-cloths, curtains, etc.
No naked flame sources, such as lighted candles, should be placed on the apparatus.
CAUTION
TO PREVENT ELECTRIC SHOCK, DO NOT USE THIS (POLARIZED) PLUG WITH ANY EXTENSION
CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE PLUG CAN BE FULLY INSERTED
WITHOUT EXPOSING ANY PARTS OF THE BLADES.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING: TO REDUCE THE
RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER
(OR BACK). NO USERSERVICEABLE PARTS
INSIDE, REFER SERVICING
TO QUALIFIED SERVICE
PERSONNEL.
The exclamation point within
an equilateral triangle is intended to alert the user to
presence of important operating and maintenance
(servicing) instructions in the
literature accompanying the
appliance.
The lighting flash with arrowhead
symbol, within an equilateral triangle, is intended to alert the user to
the presence of uninsulated "dangerous voltage" within the
product's enclosure that may be of
sufficient magnitude to constitute
a risk of electric shock to persons.
3
SAFETY INSTRUCTIONS -
Read before operating equipment
This product was designed and manufactured to meet strict quality and safety standards. There are,
however, some installation and operation precautions which you should be particularly aware of.
1. Read Instructions — All the safety and operating instructions should be read before the
appliance is operated.
2. Retain Instructions — The safety and operating instructions should be retained for future
reference.
3. Heed Warning — All warnings on the appliance and in the operating instructions should be
adhered to.
4. Follow Instructions — All operating and use instructions should be followed.
5. Water and Moisture — The appliance should not be used near water – for example, near a
bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool,
etc.
6. Carts and Stands — The appliance should be used only with a cart or stand that is recommended by the manufacturer.
6A. An appliance and cart combination should be moved with care. Quick stops, ex-
cessive force, and uneven surfaces may cause the appliance and cart combination
to overturn.
7. Wall or Ceiling Mounting — The appliance should be mounted to a wall or ceiling only as
recommended by the manufacturer.
8. Ventilation — The appliance should be situated so that its location or position does not
interfere with its proper ventilation. For example, the appliance should not be situated on a
bed, sofa, rug, or similar surface that may block the ventilation openings; or, placed in builtin installation, such as a book case or cabinet that may impede the flow of air through the
ventilation openings.
9. Heat — The appliance should be situated away from heat sources such as radiators, heat
registers, stoves, or other appliances (including amplifiers) that produce heat.
10. Power Sources — The appliance should be connected to a power supply only of the type
described in the operating instructions or as marked on the appliance.
11. Grounding or Polarization — The precautions that should be taken so that the grounding
or polarization means of an appliance is not defeated.
CAUTION: To prevent electric shock, match the wide blade of this plug
to the widle slot, fully insert. Do not use this (polarized) plug with an
extension cord, receptable or other outlet unless the blades can be fully
inserted to prevent blade exposure.
12. Power-Cord Protection — Power-supply cords should be routed so that they are not likely
to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the
appliance.
13. Cleaning — The appliance should be cleaned only as recommended by the manufacturer.
14. Power Lines — An outdoor antenna should be located away from power lines.
15. Nonuse Periods — The power cord of the appliance should be unplugged from the outlet
when left unused for a long period of time.
16. Object and Liquid Entry — Care should be taken so that objects do not fall and liquids are
not spilled into the enclosure through openings.
17. Damage Requiring Service — the appliance should be serviced by qualified service personnel when:
A.The power-supply cord or the plug has been damaged; or
B.Objects have fallen, or liquid has spilled into the appliance; or
C.The appliance has been exposed to rain; or
D.The appliance does not appear to operate normally or exhibits a marked change in per-
formance; or
E.The appliance has been dropped, or the enclosure damaged.
18. Servicing — The user should not attempt to service the appliance beyond that described in
the operating instructions. All other servicing should be referred to qualified service personnel.
4
Getting Started
Before attempting to connect, operate or adjust this product, please read these instructions completely and keep this manual for future reference.
Dear customers :
May we take this opportunity to thank you for purchasing this DVD Player.
We strongly recommend that you carefully study the operating instructions before operating the unit.
Main Features
• Front loading DVD / MP3 / CD player.
• Built-in Dolby Digital.
Standards
Video : NTSC
Audio : PCM (48 or 96 kHz), 2 Channel MPEG layer 2, Dolby AC-3 & dts line out
Features of audio specifications
– DOLBY Digital 2 ch decoding output.
– DTS for Digital (Coaxial) output
– Linear PCM output.
5
* Player is CD-R, CD-RW compatible.
Note: CD-R, CD-RW Discs recorded with writing device can only be used when they are
correctly treated.
Region Management Information
This DVD Player is designed and manufactured to respond to the Region Management
Information that is recorded on a DVD disc. If the Region number described on the DVD
disc does not correspond to the Region number of this DVD Player, this DVD player cannot play that disc.
This Region number of this DVD player is .
Disc manintenace
– Before playback, wipe the disc from the center hole toward the outer edge with a clean
cloth.
– Never use benzine, thinner, cleaning fluid, static electricity prevention liquids or any
other solvent.
Note : Dirty disc may cause bad picture.
Audio &
Video
Audio
Audio
Disc size 12cm
single side, single layer / single side, double layer
PAL and NTSC DVD disc
Playback time 135min / 240min max.
Disc size 12cm / 8cm
CD disc
Playback time 74min/20min max.
MP3 format disc
Getting Started
Disc types
MP3
Correct
From the center to the edge
Incorrect
6
Safety precautions
Warning
To avoid electrical shock, do not open the
cabinet, refer servicing to qualified personnel only.
Warning
Keep the unit away from flower vases, tubs,
sinks, etc. If liquids are spilt into the unit,
serious damage could occur.
Warning
Do not expose this equipment to rain or
moisture.
Warning
Do not block ventilation holes of the unit so
that air can circulate freely,
Attention
If smoke, malodour or unrelated noise are
emitted from the unit, turn off the power and
disconnect the AC power cord.
Attention
Touching the unit is dangerous especially if
during thunder.
Attention
When left unused for a long period of time,
the unit should be unplugged from the household AC outlet.
Attention
Be sure to turn the unit off and disconnect the AC
power cord before cleaning the unit surface. If the
surface is dirty, wipe clean with a cloth which has
been dipped in a weak soap and water solution and
wrung out thoroughly, and then wipe again with a
dry cloth.
Note: This unit is a class 1 laser product and uses a visible laser beam which could
cause hazardous radiation exposure if directed. Be sure to operate it correctly as
instructed.
7
Front Panel Control
1. Disc Tray
2. Power Indicator
a) Steady Light = play mode
b) Blinking Light = standby mode
3. Open/Close Button
4. Play / Pause Button
5. Stop Button
6. Remote Sensor
7. Power ON/OFF
Rear Panel Control
1. AC Power Cord
2. Y/Pb. Cb/Pr. Cr output
3. Video output (composite)
4. Analog Audio output
5. Digital Audio output (coaxial)
6. S-Video output
8
Battery installation (remote control unit)
1. Remove the battery cover.
2.
Insert two batteries (AAA) making sure the polarity (+/-) matches the marks inside the unit.
3. Replace the cover.
– Do not attempt to recharge, short-circuit, disassemble, heat or throw the batteries into
the fire.
– Do not mix old and new batteries
– Dispose of properly in accordance with local law.
Note : Weak batteries can leak and severely damage
the remote control unit.
Remote Control Unit
1. Power on/off Button
2. Numeric Buttons
3. Display Button
4. Volume – Button
5. Setup Button
6. DVD Menu Button
7. Direction Buttons
( Up / Down/ Left/ Right)
8. Fast Backward Button
9. Play Button
10. Stop Button
11. Slow Button
12. Subtitle Button
13. P. Scan Button
14. Search Button
15. Audio Button
16. Zoom Button
17. Eject Button
18. Volume + Button
19. Mute Button
20. Previous Button
21. Next Button
22. Enter Button
23. Fast Forward Button
24. Step/Pause Button
25. Program Button
26. Angle Button
27. Cancel Button
28. Repeat Button
29. Repeat A-B Button
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
9
Connect To TV
Caution : Turn off all te equipment before any installation.
This unit provides several types of video and audio signals output. They are :
• Y/Pb, Cb/Pr, Cr output
• RCA output
• S-Video Output
User can choose a suitable connection type to connect the player to TV.
1. Y/Pb, Cb/Pr, Cr output
2. Connection via Composite (RCA) Cable
In this type of connection, we have to connect the Left/Right Audio Cables (Red and
White) and a Video signal (Yellow).
3. Connection via S-Video Cable
Component Video
(Y/Pb, Cb/Pr, Cr)
Video in
Audio in R
Audio in L
S-Video in
Audio in R
Audio in L
10
Connection to Amplifier
There are four different types of connection between the DVD player and an amplifier.
• Digital output via Coaxial Cable (Connection 1).
• 2 channels (left/right) Audio Output (connection 2-3)
Note:
1. The Digital output cut off, when Analog output was selected.
2. The Analog output cut off, when Digital/Optical output was selected.
Video output
2
1
3
11
Operation
TV Selection
Turn on the TV, the DVD player and the Audio Amplifer System (if any).
1. Press the “TV/VIDEO” button on the TV.
2. Select the Video Mode (TV).
Note: If there are more than 1 AV channel for the TV, select the channel you have
connected to the DVD player.
3. Select the Correct Audio Input on the AV Amplifier (if any)
Play Discs
1. Press the OPEN/CLOSE button ( ) on the front panel and load the Disc on the
tray. The label side should be facing upwars. For a Double-sided DVD Disc, put the
disc with label A/1 up.
2. Press the OPEN/CLOSE button ( ) again to close the tray and the disc will be
loaded.
3. The Disc will be played automatically.
• If it is a DVD disc, it will show the Menu/Title Page on the screen.
• If it is a CD, it will play the first track directly.
4. Press the STOP button ( ) if you want to stop the Disc playback. You can resume
playback by pressing the PLAY button and it will start at the location where you have
pressed stop (Resume Play).
5. Press the STOP button twice to have the Disc stop completely.
Pause /Step
This function is applicable for DVD and CD audio.
• For DVD, the picture will freeze.
• For CD audio, it will become muted.
1. Press the PAUSE button ( ) to pause play.
2. Press the PLAY button again to resume Play.
DVD Setup Mode
• Setup Mode provides the menu for the configuration of TV DISPLAY Mode, OSD
LANGUAGE Mode, AUDIO Mode, PARENTAL Mode, PASSWORD, etc.
• Item selection in the SETUP menu is done by using the Direction button and the
ENTER button.
• To exit the SETUP menu, press the SETUP button again.
• The initial password for PARANTAL Mode is set at 1369.
Note: To setup the TV display mode, must be in stop mode.
12
Setup Menu Items :
Press the SETUP button on the remote control.
The following menu will be shown:
1. GENERAL SETUP
TV DISPLAY
• Normal/PS
This is selected when the DVD player is connected to a normal TV. Wide-screen imaged are
shown on the screen, but with some parts cut
automatically.
• Normal/LB
This is selected when the player is connected to
a normal TV. Wide screen images are shown on
the screen, with black belt on the top and bottom.
• WIDE
This is selected when the player is connected to a wide-screen TV.
ANGLE MARK
This only works when there is an angle mark on
the disc. Select ON, the screen shows the mark
when playing DVD.
- ON
- OFF
OSD LANGUAGE
This used to select the OSD language.
- English
- Spanish
- German
- French
CAPTIONS
This option can show or hide the captions.
- On (Show captions)
- Off (Hide captions)
-- GENERAL SETUP PAGE --
TV Display LB
Angle Mark On
OSD Lang ENG
Captions Off
Screen Saver On
Go To General Setup Page
-- GENERAL SETUP PAGE --
TV Display
Angle Mark English
OSD Lang
French
Captions
German
Screen Saver
Spanish
Set OSD Language
-- GENERAL SETUP PAGE --
TV Display
NORMAL/PS
Angle Mark
NORMAL/L2
OSD Lang WIDE
Captions
Screen Saver
Set TV Display Mode
-- GENERAL SETUP PAGE --
TV Display
Angle Mark
OSD Lang
CAPTIONS
ON
Screen Saver
OFF
Closed Caption
-- GENERAL SET UP PAGE --
TV Display
Angle Mark
ON
OSD Lang
OFF
Captions
Screen Saver
Set Angle Mark
13
SCREEN SAVER
Start the screen saver, the screen saver image
appears when the player stops or the image is
frozen for a few minutes. This saver can keep
the screen from being damaged.
- ON (Start the screen saver)
- OFF (Remove the screen saver)
2. SPEAKER SETUP
When SPEAKER SETUP option is selected, the
following menu will be shown.
DOWNMIX
• LT/RT
A disc recorded multi channel soundtrack, the
output signal will be incorporated to left and right
channel.
• STEREO
A disc record multi channel soundtrack, the
output signal will be incorporated to stereo.
DOLBY DIGITAL SETUP
• DYNAMIC
This option is used to set the compression ratio in
order to control the sound (volume) contrast.
3. VIDEO SETUP
When VIDEO SETUP option is selected, the
following menu will be shown. To select the
desired item use the direction ( /// )
button.
• VIDEO OUT : CVBX/S-VIDEO
YUV
• VIDEO TV : P-SCAN
INTERLACE
Note : To select P-SCAN mode, the P-SCAN
output must be connect to P-SCAN TV, otherwise
the picture will be unstable.
-- SPEAKER SETUP PAGE --
Downmix
LT/RT
Dynamic
Stereo
Set Downmix Mode
-- SPEAKER SETUP PAGE --
Downmix
FULL
Dynamic 3/4
1/2
1/4
0FF
Set DRC to 1/2 Conpression
-- VIDEO SETUP PAGE --
Video Out
CVBS/S-VIDEO
TV Mode
YUV
-- VIDEO SETUP PAGE --
Video Out
TV Mode
P-SCAN
Interlace
-- GENERAL SETUP PAGE --
TV Display
Angle Mark
OSD Lang
Captions
Screen Saver
ON
OFF
SCREEN SAVER
Loading...