Models:
5801203
DIAMOND
PRODUCTS
SPECIALTY EQUIPMENT
MANUFACTURING DIVISION
Hydraulic Hand Saw
(CW)
5801200
5801201
5801202
PARTS LIST
February 3, 2012
Part #1801030
Intentionally Blank
Warning Label
#1800767 - 15 GPM
#1800864 - 12 GPM
#1800863 - 10 GPM
#1800862 - 8 GPM
20" Frame (Shown) #6030261
24" Frame #6030262
Hydraulic Hand Saw - Clockwise Rotation
Cat #
(GPM)
Gallons Per
Part #
Hydraulic Motor
#2603295 1.57 C.I. (15 GPM) CW (Shown)
#2603296 1.27 C.I. (12 GPM) CW
Blade
Capacity-
55186
53618
Minute
15 GPM
12 GPM
5801200
5801201
20"
20"
Guard Type
53619
55187
12 GPM
15 GPM
5801202
5801203
24"
24"
47
8
46
1127
3
25
4
39
6
5
40 41
31
434219
26
Hydraulic Hand Saw (CW) Parts List
1 22 48 50 23 24 28 12
14 5152
13
38
20
21
37
342322730
33 44
29
17 1535
53
18
54
7
9
10
36
DESCRIPTION
Flat Washer, 5/16" USS
Cap Screw, Hex Hd., 1/4-20 x 2"
Lock Washer, 1/4" Split
Water Valve, 1/4"NPT
Quad Seal Ring
Elbow, 1/2" MORB x 1/2" MPT 90 Deg.
Coupler, 1/2" Q.D.
Tee, 1/2" M. JIC to 1/2" F. JIC
Elbow Fitting, 1/2"MJIC x 1/2" FJIC 90 Deg.
Elbow Fitting, 1/2" MORB x 1/2" MJIC 90 Deg.
Hose Assy, 3/8" x 12, 3/4" F.Garden x 1/4"MPT
Push-Connect Fitting, 1/4" Tube x 1/8"MPT
Plug, 1/8" NPT
1/4" Cable/Hose Loop Clamp
Water Hose, 1/4"
Rivet, 3/16" Dia.
1"-14 Jam Nut LH Grade 5
SHCS, 5/16-18 x 1 Left Hand Thd.
DP S/N Nameplate
Rivet, 3/32" Dia.
Rotation Label
Warning Label
Warning Label
Hydraulic Hose Assy. - Front
Hydraulic Hose Assy. - Rear
QTY.
PART NO.
28 2900567 1
29 2900294 2
30 2900024 2
31 3201271 1
32 2502693 2
33 3205555 1
34 3200104 1
35 3200332 1
36 3200802 1
ITEM
37 2502924 1
Hydraulic Hand Saw (CW) Parts List
DESCRIPTION
38 2702689 1 Fitting, 1/2"MORB x 1/2" MJIC
39 3201875 1
40 2506350 2
41 3200001 1
42 2502914 2
43 6079091 2
44 2900201 1
1
1800169-DP
46 2900167 1
47 2903226 1
48
49 2900053 2
50 1800865 1
51 1800767 1
52 1800001 1
53 6079089 1
54 6079090 1
Hand Saw Frame 20"
Valve Cap, Hand Saw 20" & 24"
HS Trigger Weldment
QTY.
PART NO.
1 6030262 1
2 2502911 1
ITEM
3 6040498 1
Outer Flange 4"
LD Inner Hub & Shaft LH
Dowel Pin, 3/8" x 7/8"
Hydraulic Motor, 1.57 C.I./15GPM LH THD
Carriage Bolt, 3/8-16 x 1-1/4"
4 6030206 1
5 6030391 1
6 2900605 1
7 2603295 1
8 2903037 2
Flat Washer, 3/8" SAE
Locknut, 3/8-16, Nylon
Lock Nut, 1/4-20 Nylon
1/4-20 Locknut, Nylon
Cap Screw, Hex Hd., 3/8-16 x 3/4"
Cap Screw, Hex Hd., 1/4-20 x 1-1/2"
9 2900014 2
10 2900018 2
11 2900010 1
12 2900039 1
13 2900196 1
14 2900048 1
Nipple, 1/2" Q.D.
Adaptor, #12 O-Ring x 1/2 MJIC
Adaptor Fitting, 1/2" MPT x 1/2" FJIC
Elbow Fitting, 1/2" MJIC x 5/8" MORB
Metro Flow Valve
Washer, 3/8" x 1-5/8"
Bellow, Hand Saw
15 3200105 1
16 2502920 1
17 3201274 1
18 3200803 1
19 2702688 1
20 2907070 1
21 2507033 1
Pivot Bolt
22 2501568 1
Bushing UHMW
Bearing
1/4" x 1/2" Sleeve Bushing
Flat Washer, 1/4" USS
23 2501583 2 Bearing, 3/8" ID Flanged Bronze
24 2501515 1
25 2502897 1
26 2502576 1
27 2900126 4
Intentionally Blank
NOTES & RECORDS
DATE NOTE BY
EQUIPMENT AND PARTS
WARRANTY
Diamond Products warrants all equipment manufactured by it against defects
in workmanship or materials for a period of one (1) year from the date of
shipment to Customer.
The responsibility of Diamond Products under this Warranty is limited to
replacement or repair of defective parts at Diamond Products’ Elyria, Ohio
factory, or at a point designated by it, of such parts as shall appear to us upon
inspection at such parts, to have been defective in material or workmanship,
with expense for transportation and labor borne by Customer.
In no event shall Diamond Products be liable for consequential or
incidental damages arising out of the failure of any Product to operate properly.
Integral units such as engines, electric motors, batteries, transmissions,
etc., are excluded from this Warranty and are subject to the prime
manufacturer’s warranty.
THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED
OR IMPLIED, AND ALL SUCH OTHER WARRANTIES ARE HEREBY
DISCLAIMED.
333 Prospect Street, Elyria, Ohio 44035
(440) 323-4616 (800) 321-5336 Fax (440) 323-8689
www.diamondproducts.com
Printed in U.S.A.
Loading...