Flybook V5_User's Guide_V1.0.book Page i Thursday, February 8, 2007 3:44 PM
Flybook V5 User’s Manual
V5W1BB (without 3G)
V5W1BBHA (with 3G)
Dialogue Technology Corporation
Version 1.0, Jan.. 2007
Flybook V5_User's Guide_V1.0.book Page ii Thursday, February 8, 2007 3:44 PM
Flybook V5_User's Guide_V1.0.book Page i Thursday, February 8, 2007 3:44 PM
Preface
Copyright and Safety Notices
Please read this section before using your computer.
Retain this manual for future reference.
Copyright
This publication, including all photographs, illustrations and
software, is protected under international copyright laws,
with all rights reserved. Neither this manual, nor any of the
material contained herein, may be reproduced without written consent of the manufacturer.
Disclaimer
The information in this document is subject to change without notice. The manufacturer makes no representations or
warranties with respect to the contents hereof and specifically disclaims any implied warranties of merchantability or
fitness for any particular purpose. The manufacturer
reserves the right to revise this publication and to make
changes from time to time in the content hereof without
obligation of the manufacturer to notify any person of such
revision or changes.
Flybook V5_User's Guide_V1.0.book Page ii Thursday, February 8, 2007 3:44 PM
Preface
Trademark Recognition
Bluetooth is a trademark of the Bluetooth SIG, Inc. (Special
Interest Group). The Bluetooth trademark is owned by Blue-tooth SIG, Inc. USA. BlueSoleil is a trademark of IVT Corporation. Dialogue Technology Corporation is a registered
trademark. FlyBook is a trademark of the Dialogue Technology Corporation. Windows is a registered trademark or
trademark of Microsoft Corporation in the United States
and/or other countries. All other product names used in this
manual are the properties of their respective owners and
are acknowledged.
Federal Communications Commission (FCC)
This equipment has been tested and found to comply with
the limits for a Class A digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more
of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and the
receiver.
•Connect the equipment onto an outlet on a circuit differ-
ent from that to which the receiver is connected.
•Consult the dealer or an experienced radio/TV techni-
cian for help.
ii
Flybook V5_User's Guide_V1.0.book Page iii Thursday, February 8, 2007 3:44 PM
Shielded interconnect cables and a shielded AC power
cable must be employed with this equipment to ensure
compliance with the pertinent RF emission limits governing
this device. Changes or modifications not expressly
approved by the system's manufacturer could void the
user's authority to operate the equipment.
Declaration of Conformity
This device complies with part 15 of the FCC rules. Operation is subject to the following conditions:
•This device may not cause harmful interference, and
•This device must accept any interference received,
including interference that may cause undesired operation.
Preface
FCC Caution
Any changes or modifications not expressly approved by
the party responsible for compliance could void the user's
authority to operate this equipment.
The antenna(s) used for this transmitter must not be colocated or operating in conjunction with any other antenna
or transmitter.
Enabling wireless LAN and wireless WAN simultaneously in
one computer is not allowed . While one is in use, the other
will be turned off.
Running wireless devices in the aircraft is prohibited. Make
sure all wireless devices in your computer are turned off
during the flight.
iii
Flybook V5_User's Guide_V1.0.book Page iv Thursday, February 8, 2007 3:44 PM
Preface
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum
distance of 20 cm (8 inches) between the radiator and your
body.
FCC Wireless Regulation
Due to the FCC regulations, wireless LAN and wireless
WAN modules shall not work in a machine simultaneously.
If these two modules are installed in the V5, while one is in
use, the other will be off automatically by the system.
iv
Battery Caution
Danger of explosion if battery is incorrectly replaced. Replace only
with same or equivalent type recommended by the manufacturer.
Discard used batteries according to the manufacturer’s instructions.
About This Manual
This User’s Manual provides information to help you operate and get the most from your Flybook V5. Read the Quick
Start Guide to quickly set up and begin using your computer.
Please read “
before using your computer.
Copyright and Safety Notices” on page i
Taking Care of the Flybook V5
After you unpack your computer, store the packing materials in case you want to ship the computer or if you have to
return it for servicing.
Flybook V5_User's Guide_V1.0.book Page v Thursday, February 8, 2007 3:44 PM
Your notebook computer is a precision instrument that
should be handled with care. Use common sense and follow the guidelines below, and your computer will last you
for many years.
Do’s and Don’ts with the Flybook V5
•Do not twist the display counterclockwise.
•Do not place heavy objects such as books on the com-
puter.
•Do not use the Flybook V5 near water or a heat source
such as a radiator.
•Do not expose the computer to temperatures above 50°
C or below 0° C.
•Keep the computer away from direct sunlight or heat
sources.
•Do not expose the computer to rain or moisture.
•Do not spill water or any other liquid on the computer.
•Do not place the computer near magnetic fields.
•Avoid subjecting your computer to heavy shocks or
vibrations.
•Do not expose the computer to dusty or dirty environ-
ments.
•Do not place the computer on uneven surfaces.
•Do not cover the air vents around the computer.
•Only use the AC adapter that is provided with your com-
puter.
Preface
Safety Information
The Flybook V5 has been designed and tested to meet the
most recent standards of safety in notebook technology
equipment. To ensure safe use of the Flybook V5, refer to
the following safety instructions and any caution or warning
messages on the equipment or in the user manual.
v
Flybook V5_User's Guide_V1.0.book Page vi Thursday, February 8, 2007 3:44 PM
Preface
•Read and follow all instructions marked on the
Flybook V5 and in the user manual before operating the
V5. Store all safety information in a secure place for
future reference.
•Always set the Flybook V5 on a stable surface.
•Only operate the Flybook V5 from the type of power
source indicated on the rating label on the AC adapter.
•Ensure all ventilation openings are not blocked or cov-
ered. Keep an adequate space (around 6 inches or 15
cm) around the Flybook V5. Never insert objects of any
kind into the ventilation openings.
•When using an extension cord with the Flybook V5,
ensure that the total ampere rating on the equipment
connected to the cord does not exceed the extension
cord ampere rating maximum value.
•Only use the supplied power cord. Do not place any-
thing on the power cord. Place the power cord where it
will not be in the way of foot traffic.
•Always unplug any modem, LAN, or power cables from
the Flybook V5 before you clean it.
vi
Flybook V5_User's Guide_V1.0.book Page vii Thursday, February 8, 2007 3:44 PM
Preface
Warning! The
safety strap is only
to prevent dropping
the V5. It is not
designed for carrying the V5.
•When using the Flybook V5 in tablet mode, use the
safety strap to avoid dropping the Flybook V5.
1
2
Contacting Service
Disconnect the Flybook V5 from power and contact qualified service personnel if any of the following occurs:
•The power cord or adapter is damaged.
•Liquid has been spilled on the Flybook V5
•The Flybook V5 does not operate correctly when oper-
ating instructions are followed.
•The Flybook V5 has been dropped, or the case is bro-
ken open.
•Flybook V5 performance is seriously degraded.
If service is required, contact a sales representative or a
local service center, or go to http://www.dialogue.com.tw
service information.
for
vii
Flybook V5_User's Guide_V1.0.book Page viii Thursday, February 8, 2007 3:44 PM
Preface
Warning! Before
cleaning the computer, turn it off,
unplug the AC
adapter, and then
remove the battery
Caution: Do not
wipe the keyboard,
pointing device,
pointing device
buttons, or
fingerprint reader
with a damp cloth.
Cleaning the Flybook V5
Follow these instructions when cleaning the Flybook V5.
•Wipe the display with a clean soft cloth.
•If you use a mild glass cleaner to clean the display,
.
spray a little on the cloth and then wipe the display. Do
not spray cleaner directly onto the display.
•Clean the outside of the computer case with a soft cloth.
You can moisten the cloth with a non-alkaline detergent.
•Use a vacuum cleaner to clean dust from the keyboard.
viii
Flybook V5_User's Guide_V1.0.book Page ix Thursday, February 8, 2007 3:44 PM
Table of Contents
Preface..................................................................................................................... i
Copyright and Safety Notices ........................................................................... i
About This Manual ............................................................................................. iv
Taking Care of the Flybook V5........................................................................ iv
Introducing the Flybook V5 .......................................................................1
Taking a Tour of the Flybook V5 ............................................................ 3
Congratulations on
purchasing the
Flybook V5! The
Flybook V5 supports both Windows XP and the
newest member of
the Windows operating system family, Windows Vista.
The V5 is a powerful mobile computer
which performs
dual duty as a notebook or tablet computer. Advanced networking features
include WLAN, WWAN, Bluetooth, and even an internal
modem.
The Flybook V5 uses a pointing device with mouse buttons
on both sides of the unit and a clickable scroll bar for added
convenience. The LCD monitor can be rotated and laid flat
to enable you to use the Flybook V5 as a tablet computer.
Using the stylus, you can write text and draw on the tablet
as you would on conventional paper.
The built-in webcam enables you to be seen by contacts
using Windows MSN or other messaging software. The
camera can be rotated 225 degrees for maximum flexibility.
The powerful Li-ion rechargeable battery provides more
than 3 hours of mobility, making the Flybook V5 the best
choice for people on the go.
1. Status LEDs
– These LEDs display when the AC adapter is con-
nected, when the HDD is being accessed, or when
the WWAN, WLAN, or Bluetooth is activated.
2. Pointing device buttons (right)
– These pointing device buttons emulate mouse right
and left buttons. The top button corresponds to a
mouse right button. The lower button corresponds to
a mouse left button. Refer to “
Input Devices” on page 21 for more information.
3. Scroll bar
– This bar enables you to scroll up and down in web
pages or word processing software. Refer to “
Flybook V5 Input Devices” on page 21 for more
information.
Using Flybook V5
Using
4. Stick pointer device
– The Stick Pointer moves the cursor in the direction of
the pressure you apply with your finger.
5. RF kill switch
– Wireless transmission uses power. Use this button to
disable the wireless feature of your computer to save
power or when instructed to do so, for example on
an aircraft.
6. Fingerprint reader
– When you set up fingerprint authentication, you can
use the fingerprint reader to turn on the computer. In
addition to logging in to the computer, the fingerprint
can control access to some applications.
7. Power button
– Press and hold the power button for two seconds to
turn on the computer.
8. Left speaker
– Stereo speakers are built into the computer. The
right speaker is on the opposite side of the V5.
9. Pointing device buttons (left)
– These pointing device buttons emulate mouse right
and left buttons. The right button corresponds to a
mouse right button. The left button corresponds to a
mouse left button. Refer to “
Devices” on page 21 for more information.
10. AC power connector
– Connect the AC adapter to this connector.
Using Flybook V5 Input
2
11. Middle mouse button
– This button corresponds to the center button on a
conventional mouse.
12. Stereo Microphones
– Use the built-in stereo microphones for recording
sound or video conferencing with friends.
13. Webcam and webcam LED
– Use the built-in webcam for video conferencing with
friends. The LED indicates when the camera is
active
close the battery
lock after inserting
the battery. If the
battery lock is not
closed, the battery
could fall out when
carrying the computer and cause
injury or damage
the battery.
The battery lock must be manually closed. The battery
release is spring loaded and closes automatically when you
insert the battery.
Installing the Battery
1. Slide the battery lock to the unlocked position .
2. Align the guides on the sides of the battery with the
guides in the bay and then install the battery.
14
3. Slide the battery lock to the locked position .
1. Slide the battery lock to the unlocked position .
4
2. While holding the battery release in the open position
, remove the battery.
Charging the Battery
The first time you charge the battery, you should charge it
for eight hours. Thereafter, the standard charging time is
about three hours. To charge the battery, install it in the
computer (see “
connect the AC adapter (see “
on page 16).
tery is installed,
then the battery
LED is always off.
1.Battery
(V5 is running)
– LED off: No battery
– LED on: Battery discharge or battery is charged fully
– LED blink slowly: Battery is charging.
– LED blinks quickly: Battery's capacity is below
10%.
5
Note: The wireless
WAN module is
available only on
some V5 models.
2. Hard drive
– Red: The hard drive is being accessed.
3. Wireless LAN
– Off: The wireless LAN module is turned off.
– On: The wireless LAN module is turned on.
– Blinking: Data is being transmitted or received.
4. Wireless WAN
– Off: The wireless WAN module is turned off.
– On: The wireless WAN module is turned on.
– Blinking: Data is being transmitted or received.
The fingerprint reader allows you to control access to your
computer system and applications.
To enroll your finger and use the fingerprint applications,
see the bundled Quick Start Guide and Fingerprint Reader
Utility Guide or the online help for the fingerprint reader utility.
The Flybook V5 incorporates several ways to interact with
the operating system and applications. The V5 has a keyboard that emulates a standard keyboard with the addition
of Fn hotkeys. The easy to use pointing device enables you
to perform the same function as a mouse or touchpad. Buttons are located on both the left and right side of the V5 for
easy access. A scroll bar enables you to scroll up and down
in web pages or word processing applications. Finally, the
stylus emulates a mouse when using the V5 as a tablet
computer, and also enables you to write on the screen.
The pointing device consists of a stick pointer and two sets
of dual click-buttons located on the left and right side above
the keyboard. The scroll bar emulates a clickable mouse
wheel.
Left mouse
button
Center mouse
button
Left mouse
Stick pointer
button
Right mouse
button
Right mouse
button
F10
F12
ScrLk
Scroll bar
Press the stick pointer in the direction that you want the cursor to move. The left buttons emulate the left, center, and
right buttons of a standard 3 button mouse. The two right
buttons and scroll bar correspond to the two buttons and
click wheel of a clickable wheel type mouse.
To customize the pointing device, click Start | Control Panel and then double-click the Mouse icon to open the
pointing device configuration utility. The configuration utility
lets you customize settings to your preference. Click Help
in the pointing device utility for instructions on changing settings.
The stylus not only emulates a mouse when the V5 is in
tablet mode, it also enables you to interact with the
Flybook V5 as you would with paper and pen. You can navigate the OS, write, and draw on the screen.
Calibrating the Stylus for the First Time
Before using the stylus with the Flybook V5, you should first
calibrate the display.
For calibrating and using the stylus, please refer to the bundled Touch Panel Utility Guide for further information.
The V5 keyboard emulates a standard-sized computer keyboard by incorporating function keys, a numeric keypad,
and the Fn key.
Using Function (Fn) Keys
Using function keys is
a quick way to carry
out commands or
enable features on
your computer. Function keys have a blue
icon or have blue text
(such as on the Home
and PgDn keys). To
use this function, press
and hold the Fn key (1)
and then press a function key (2).
some function key
combinations (for
example, Fn + F8)
shows an On
Screen Display
(OSD) to indicate
the function used.
Using Flybook V5 Input Devices
The Fn key functions are described as follows.
– Fn + Esc: Repeatedly pressing the buttons outputs
the display signal to one of the following:
– Connected external display only
– Both a connected external display and system display
– System display only
If no external display is connected, pressing this key
combination has no effect.
– Fn + ~: Turns the V5 LCD off.
– Fn + F1: Decreases the display brightness.
– Fn + F2: Increases the display brightness.
– Fn + F3: Puts the computer in suspend mode.
– Fn + F4: Puts the computer in hibernation mode.
– Fn + F5: Mutes/enables the volume.
– Fn + F6: Decreases the volume.
– Fn + F7: Increases the volume.
– Fn + F8: Enables or disables the built-in wireless
– Fn + F9: Enables or disables the built-in wireless
wide area networking (WWAN) feature.
– Fn + F10: Enables or disables the built-in Bluetooth
feature.
– Fn + Alt: Turns on or off the built-in webcam.
– Fn + Shift: Turns the GPS function on and off.
– Fn + ScrLk: Enables or disables scroll lock. When
enabled, press the up or down arrow keys to scroll
up or down one line respectively.
– Fn + PrtSc: Print screen captures the on-screen
image to the clipboard. You can then copy the contents to an image editing program.
– Fn + SysRq: Terminal request. This key is rarely
used.
– Fn + Home: Displays the first page of a document or
moves the pointer to the beginning of a line in text.
– Fn + End: Displays the last page of a document or
move the pointer to the end of a line in text.
– Fn + PgUp: Moves text up one screen at a time.
– Fn + PgDn: Moves text down one screen at a time.
– Fn + A: Enables or disables the automatic light sen-
Windows start here
booklet for additional keyboard
shortcuts.
Using Flybook V5 Input Devices
Using the Numeric Keypad
The keyboard has an
embedded numeric
keyboard. When you
enable it, the Num
Lock LED lights. To
enable or disable the
numeric keypad, press
Fn + Num Lk.
The illustration shown
here displays the location of the embedded numeric keyboard keys.
Using Windows® and Other Keys
Keys such as the Windows start and application keys, and
the Caps Lock key function the same as on a standard
keyboard in the Windows environment.
The Flybook Control Center lets you quickly enable or disable wireless options and change settings such as volume
and display mode. You can also check system health with
this utility.
The Control Center is most often used in tablet mode to
access frequently used features that are normally
accessed with function keys in clamshell mode. Also, some
functions available in the Control Center are dedicated for
tablet mode use.
1. Right-click the Flybook icon in the System Tray and
select Restore.
The Control Center Opens.
30
2. Click the left arrow button to open/close the left side
pane, and click the right arrow button to open/close the
right side pane. The left side pane displays additional
function buttons, while the right side pane displays the
health information of the system.
the USB icon on
the connector is
facing downwards
as shown in the
illustration. Connecting a USB
cable incorrectly
can damage the
connector on the
computer.
Connecting Devices
Connecting USB Devices
There are two Universal Serial Bus (USB) connectors on
the Flybook V5. You can connect USB devices such as
printers or flash drives to either connector.
1. Connect the USB device to one of the USB connectors
permanently
damage a display if it does not
support the resolution that your
computer is set
to. Match the resolution of the V5
to the external
display before
you attach it to
the computer.
You can connect an external monitor, projector or LCD to
your computer with a resolution up to 1800 x 1440. Check
the user manual of the display to be sure it supports this
resolution.
1. Connect the external display to the monitor connector
on the computer.
40
2. Connect the display to an electrical outlet and then turn
on the display.
3. Press Fn + ~ to switch to the external display.
outputting the
display to a
video device,
check the
device’s input
signal type and
change your
computer’s output signal type
to meet it. The
V5 outputs
NTSC or PAL
video signals.
Select the type
in BIOS Setup
Utility. The
default setting is
Auto.
Connecting Devices
Connecting to a TV
You can connect a TV to the Flybook V5 to use as an external monitor.
1. Plug the 3.5 mm TV cable adapter into the TV cable
jack at the rear of the Flybook V5.
TV
2. Connect the other end of the TV cable jack to a com-
posite video RCA cable (yellow connector).
3. Press Fn + ~ to change the V5 output to the television.
You can use 34 mm-wide and 54 mm-wide ExpressCards
with your Flybook V5.
Caution: Do not
install or remove an
ExpressCard when
the computer is in
standby or hibernate mode. Static
electricity in your
body can damage
ExpressCards. To
reduce the static
electricity in your
body, touch a bare
metal table or a
grounded metal
object before installing an ExpressCard.
Installing an ExpressCard
1. Find the notched edge on the card as shown in the fol-
Connecting your computer to the Internet opens the way to
potential threats such as viruses and spyware. To best
secure your computer purchase security software (or download it from a secure system), and then install it on your
computer before you connect it to the Internet.
To check your computer’s security settings click Start | Control Panel, and then click Security Center in Category
View or double-click Security Center in Classic View.
11
Installing a Firewall
A firewall protects your computer by blocking or allowing
traffic between your computer and the Internet. Windows
has a built-in firewall that helps to protect your computer.
For better security, purchase a router that has a built-in firewall. You can also download free firewall software on the
Internet.
Spyware typically retrieves information about your Websurfing habits. It can be secretly installed on your computer
with a free download and can even be installed just by visiting a Web site. Spyware can cause your Web searches to
be redirected and pop up annoying adds. Once your computer is infected with spyware, it can be very difficult to
remove. The key is to prevent infection in the first place by
installing spyware blocker software. Spyware blocking software can be purchased online; and you can even download
free spyware blocking programs.
tance with local network connections,
consult your network administrator
or see the Windows
online Help and
Support Center to
obtain a solution.
Your computer has an Ethernet connector that you can use
to connect to a wired network at home or in the office. If you
have a wireless access point, you can also get online using
the built-in wireless LAN of your computer.
Connecting a LAN
Wired connections are more secure and more stable than
wireless connections. You can connect your computer to
the network while it is turned on. Refer to the following to
set up a wired connection:
1. Connect an Ethernet cable to the Ethernet connector on
2. Connect the other end of the cable to your router or
switch.
It takes a few minutes for your router to assign an IP
address to your computer. When your computer is connected, the following message appears over the LAN
icon in the System Tray.
3. Double-click the LAN icon to view details for your con-
nection.
Connecting a Wireless LAN (WLAN)
Use your computer’s built-in wireless LAN module to
access your home or office network. The wireless LAN
module is powered by the Intel® PROSet/Wireless utility.
Wireless systems work in infrastructure mode or peer-topeer mode. In infrastructure mode, wireless devices communicate to a wired LAN via access points. In ad-hoc mode
(also known as peer-to-peer mode), wireless devices communicate with each other directly and do not use an access
point.
To connect to a wireless network:
1. Press Fn + F8 to enable the wireless LAN module.
2. The Intel(R) PROSet wireless module automatically
scans for available networks.
3. Follow the on-screen prompts to access a network.
Click Help in the Intel® PROSet/Wireless utility for
assistance.
4. Click the utility icon in the system tray at any time to
The built-in fax/data modem module enables you to connect the V5 to a remote network or the Internet or fax documents.
Making a Dial-up Connection
13
Before making a dial-up connection, you must install connection components in Windows and create a dialing profile
for the connection. More than one profile can be created for
different connection purposes.
Creating modem dial-up connection components
To install modem dial-up connection components:
1. Click Start | Control Panel and double-click the Net-
work Connections icon.
2. Click Create A New Connection to open a wizard that
will instruct you how to install dial-up connection components and set up a profile.
When a component is created, an associated icon is displayed in the Network Connections window. For more information on installing modem dial-up components, refer to
the Windows online Help and Support Center.
1. Connect a phone jack to the RJ-11 jack at the rear of
the Flybook V5 to use the built-in modem.
2. In the Network Connections panel, double-click the icon
of the component you wish to use to make the connection.
Once the connection is established, the icon shows “connected”. Click the icon to open the status window to check
or stop the connection, or open its connection properties
window and configure this connection component.
Windows supports other modem dial-up connection utilities.
If you have other utilities installed, see their guides or online helps to learn how to create and make connections.
The built-in fax/data modem module supports faxing. You
can use Windows Fax or other fax applications to send and
receive faxes. Windows also provides a fax printer service
transferring from printer function of programs. Refer to the
Windows online Help and Support Center for further details,
or refer to your fax application’s online help or user guide.
accommodates various 3.5G WWAN
modules (HSDPA /
UMTS / EDGE/
GPRS / GSM) and
advanced modules.
Please check the
model of your V5 to
identify the module
that is installed.
The optional built-in WWAN module uses cellular carriers
for transmission. It enables you to connect your Flybook V5
to the Internet or use the V5 to make phone calls.
Before using the module, you must apply for an access
account, and get a SIM card and dialing profile from your
wireless WAN service provider. The SIM card acts as an
access permission key for your account.
card making sure
it is inserted all
the way to the
bottom of the
slot.
6. Close the SIM card holder and
lock it in place.
7. Replace the battery.
OPEN
PRESS LOCK
Connecting the V5 to a Wireless WAN
1. Press Fn + F9 to turn on the wireless WAN module, or
click the WWAN icon in the Flybook Control Center.
Your WWAN utility opens.
2. When the module is turned on, it seeks your service
provider’s network and registers. If the service provider’s network is inaccessible, the module continues to
search for other available networks and ask you to
select one and register.
3. Double-click the WAN connection status icon in system
tray to check the connection status.
Refer to the “Flybook WWAN Utility Guide” booklet or the
online help for information on using the utility.
Using the built-in Bluetooth module the computer can communicate with Bluetooth-equipped devices such as computers, cellular phones, printers, faxes, keyboards, and
pointing devices. The module also enables you to take
advantage of the following versatile Bluetooth services:
To enable the Bluetooth module, press Fn + F10; a Bluetooth icon appears in the system tray. Double-click the icon
to open the main window of the utility.
Read the online help of the Bluetooth utility to see how to
use Bluetooth services.
The Flybook V5 optionally comes with GPS (Global Positioning System) capability. GPS is a satellite-based radio
navigation system. Signals from at least four satellites compute the current latitude, longitude and elevation of a GPS
receiver anywhere on earth to within a few meters.
Press Fn + Shift to activate the GPS function. The GPS
icon appears in the system tray.
16
For more information on using GPS, consult the online help
or user’s guide bundled with your GPS application.
cam enabled application is open, the
webcam LED lights
when you turn on
the webcam.
Your computer features a built-in webcam that is already
set up and ready to use with most of web applications that
support video messaging, such as MSN Messenger or
Skype.
Enabling the Webcam
To use the webcam:
1. Press Fn + Alt to enable the built-in webcam.
2. Open your favorite application and launch the webcam.
Refer to the help of the application to learn how to use
the webcam.
The computer controls its power activities through an ACPI
power management unit. The unit employs a set of power
management schemes to maximize power conservation
and optimize system performance. Windows manages all
power-saving features and provides a Power Options utility
in customizing the computer’s power system.
To start the Power Options utility:
1. Click Start | Control Panel.
2. Double-click the Power Options icon to display the
Power Options Properties window.
18
3. Following the indications to check and change the
settings.
Customize your computer’s power system in this window.
Refer to the Windows online Help and Support Center to
see ACPI and Power Options if necessary.
you understand any
changes you make
to BIOS settings.
Choosing incorrect
settings can cause
your V5 not to boot
up.
Note: To e x i t B I O S
Setup without saving your changes,
select Exit Discard-ing Changes and
press Enter. When
prompted to save,
select No and press
Enter.
The BIOS setup utility enables you to you change core settings on your Flybook V5 such as the system time, boot
order, and auto-repeat rate for your keyboard. Most users
will find the default settings optimal for their needs.
Accessing the BIOS Setup
When you turn on your computer a message Press F2 to
enter BIOS appears. Press F2 to enter the BIOS setup.
On the right side of the Setup screen is an area labeled
Item Specific Help. This area lists navigation key shortcuts
and information that is specific for the item that is selected.
Updating the BIOS Firmware
You can download updated BIOS from the manufacturer's
Web site and upgrade the BIOS on your computer. New
BIOS may provide support for new peripherals, improvements in performance or fixes for known bugs.
To download firmware, please go to
http://www.dialogue.com.tw
In each problem-specific section, try the steps in the order
suggested. This may help you to solve the problem more
quickly.
Try to pin point the problem and thus avoid replacing nondefective parts.
Keep a record of the steps you take when troubleshooting:
The information may be useful when calling for technical
support or for passing on to service personnel.
A
Identifying Problems
Follow the steps below to identify your problems:
1. Turn off the computer.
2. Disconnect any peripheral devices such as an external
mouse or printer.
3. Make sure that the AC adapter is properly connected to
your computer and the power source is good. (Use
some other electrical device to confirm that the electrical outlet is working.)
4. Leave the computer off for approximately 10 seconds,
and then switch it on again. The computer should enter
the boot sequence and start normally.
5. If the computer does not start normally, look for a
If failure is detected in an area other than the mainboard, an
error message is displayed on the screen and testing is
stopped.
If your system does not successfully start, but displays a
blank screen, emits a series of beeps, or displays an error
code, consult your dealer.
General Hardware Problems
A few common hardware problems and suggested solutions are presented below:
The display screen is dark
1. Adjust the screen brightness.
2. Make sure that the computer is not in suspend mode.
68
An incorrect date and time are displayed.
Correct the date and time using the DOS DATE and TIME
commands or the options in the Setup Utility. (You can also
set the date and time in Windows by double clicking the
clock on the task bar or in the control panel.) If the date and
time become incorrect after a short time, your CMOS battery may be depleted. Contact your dealer to change the
battery.
The computer does not start or boot-up
1. If the power indicator is not on, the computer is without
power. Make sure you have properly attached the AC
adapter and power cord, or have installed a charged
battery.
2. If the computer is running on battery power, ensure that
the battery charge is not low. If the battery appears to
be charged, it may be faulty.
3. If the computer is using the AC adapter, ensure that the
AC outlet, airplane seat jack, or car cigarette lighter are
working. If the AC outlet power is working, the AC
adapter may be faulty.
Hard drive or external boot-up device is inaccessible
1. If the hard disk indicator is lit, BIOS may be incorrectly
set. Revise the BIOS settings for the Primary Master.
2. Security may be set to prevent starting the operating
system.
3. If you choose to boot up your system from an external
device through a USB port, make sure it is on and bootable media is inserted.
The screen is blank or the display is abnormal
1. The computer may be set to an external display device
only. Press Fn + F1 to switch to the V5 display.
2. The power management system may automatically
blank the screen to save power, and is in video time-out,
standby mode, or hibernation mode. Press any key,
move the pointer, or push the power button to turn on
the display.
3. The angle of the display and the brightness level is inad-
equate for the ambient lighting. Adjust the display angle
and press Fn + F2 or Fn + F3 to adjust the brightness
level.
4. The LCD screen has a default resolution of 1280 x 768
(WXGA). If you set the resolution lower than this, the
screen expands to fill the display. When the system can
not expand its display to full screen on the LCD screen
or on an external display device, you can right click on
Windows desktop and select Properties to open the
Display Properties window. Then click the Settings
tab and set the resolution to an appropriate value.
1. The audio system is closed or the volume of audio sys-
tem is too low. Use hot keys or Flybook Control Center
to open the audio system and adjust the volume.
2. The audio output is disabled or too low for the audio
application. Open the audio output and adjust the volume.
3. When plugging an earphone or external speaker into
the earphone/line-out jack, the built-in speakers are disabled automatically. If you can not hear sound from the
built-in speakers, ensure that nothing is plugged into the
jack.
The keyboard, pointing device or connected mouse
does not work properly
1. The system may have entered Suspend to RAM mode.
Push the power button to resume the system.
2. An application may have locked out your input device.
Restart your system.
3. If the keyboard or mouse does not respond on the USB
port, ensure that the devices are installed properly and
that drivers are installed.
Cannot connect to a wireless LAN
1. An incorrect network name (SSID) or network key may
be used. Make sure you have set the network name
(SSID) and key to the same values as the access point
(infrastructure connection) or the computers to be connected (Ad Hoc connection) have.
2. The computer may be too far from other communication
devices. Retry the connection after moving your computer closer to the computers to be connected with (Ad
Hoc connection) or to the access point (infrastructure
connection). Also, check the wave condition in the Wireless Network Connection Status window.
3. Check if the wireless LAN module is turned on. Verify
that Disable Radio is not checked in the Network setting
window.
4. Make sure you have access rights or network authenti-
cation to the network you want to connect to.
5. Try changing channels to avoid active channel duplica-
tion.
6. Check the setting of the protocol, work group, shared
setting, and IP address.
Cannot charge battery or losing power quickly
1. Verify that the battery is properly installed and it is not
too hot or too cold.
2. Calibrate the battery.
3. The installed battery may be faulty. Replace it with a
new one.
A
Having the V5 Serviced
If you are unable to solve the problem, you should have the
computer serviced. Pack the computer in the original carton. Include a description of the problem and a checklist of
the steps you took when trying to fix the problem. The information may be useful to the service personnel. Return the
computer to the place you purchased it.
Input devicesTouch Panel; Landscape and Portrait dual
InterfaceUSB 2.0 port x 2
Battery Swappable Li-lon rechargeable battery (6 x
Dimensions Dimensions: 235 x 165 x 29.5 mm
Color Selection Gold / Pink / Black / Silver
mode
Pointing device with 2 sets of Mouse buttons
and a clickable scroll bar
80 Key standard keyboard (Multiple languages
support) with hot keys
RJ-45 LAN jack x 1
RJ-11 Modem jack x 1
Earphone jack x 1
Microphone jack x 1
54mm-wide PCI Express Card slot x 1
D-sub 15 pin VGA port x1 (for external monitor)
TV-out jack x 1
1800mAH)
Weight around 1270g (when fully equipped)
74
Electrical specifications
DC-In power supply (Through DC-IN Power Jack)
•Input Rating: 15-19VDC, 2.64-3.34A, 50W.
•Maximum Operating Temperature (Ambient): 38
degrees C
AC adapter
•Model No: Delta ADP-50HH Rev. A.
•Input Rating: 100-240VAC, 50-60Hz, 1.5A.
•Output Rating: 19VDC, 2.64A, Class II, Marked LPS.
Flybook V5_User's Guide_V1.0.book Page i Thursday, February 8, 2007 3:44 PM
This publication, including all photographs, illustrations and software, is protected under international
copyright laws, with all rights reserved. Neither this manual, nor any of the material contained herein,
may be reproduced without written consent of the manufacturer.