Page 1
Document No: 9100-127-1112-99 REV B
Issued: April 03, 2009
Sheet 1 of 2
OBSTRUCTION / VISUAL SIGNAL LIGHT
SINGLE and DUAL FIXTURES
INSTALLATION INSTRUCTIONS and PARTS LIST
PART No:
860-1x01-00x
860-1x04-00x
860-1x06-00x
860-4x02-00x
860-6x01-001
860-8x04-001
120 VAC, Single or Dual
48 VDC, Single or Dual
10-27 VDC, Single or Dual
240 VAC, Single or Dual, 50 cd
120 VAC, Single or Dual, Canada
48 VDC, Single, Sweden
WARNING:
DE-ENERGIZE CIRCUIT BEFORE INSTALLING OR WORKING ON FIXTURE
CAUTION
To retain seal integrity (and preserve warranty) do not loosen or remove the clamp holding the light assembly together
REMOVAL OR LOOSENING OF THE CLAMP WILL VOID ALL WARRANTIES
The light assembly fixture can be mounted in any position. When mounted 'upright' [as illustrated] the fixture will meet the designed
optical specifications for Aircraft Obstruction Warnings. When mounted in any other position, the fixture will not meet the designed
optical specifications mentioned and will be considered as a visual signal fixture.
SINGLE FIXTURE INSTALLATION STEPS:
• The single housing 2A has a 1” NPT [3/4" bushing] end to be assembled to conduit … right angle or vertical
o Use a 1-1/2” wrench to attach and tighten the single housing 2A to the conduit
o Use the 1” NPT plug 4 to close threaded opening not being used
o Remove reducing bushing 5 if threading into 1” NPT conduit
• Feed the supply wires through the conduit and single housing 2A leaving approx 6” of wire for termination inside the single
housing 2A .
• Electrically connect the supply wires to the light assembly 1 wires
o Connect the light assembly wire (with voltage label) to the Hot AC or Positive [+] line
o Connect the light assembly wire [without label] to the Neutral AC or Negative [-] line
o Connect the grounding wire [from green screw] to the Ground line
• Tuck the connected wires inside the single housing. 2A .
• Position light assembly 1 on the wire single housing 2A and use the holding
screws 3 to secure the light assembly in place
• Restore power and verify operation
1501 Route 34 South, Farmingdale, NJ 07727 USA Tel: [+1] 732-919-3119 Fax: [+1] 732-751-5778 www.dialight.com
860-1x02-00x
860-1x02-00x EU
860-1R01-001-FAA
860-4x02-00x EU
860-7X02-002
[last 3 digits ... 001 = Single 002 = Dual]
240 VAC, Single or Dual
230 VAC, Single or Dual, Europe
120 VAC, Single
230 VAC, Single or Dual, Europe
240 VDC, Dual, Australia
860-1x03-00x
860-3x03-00x
860-1x05-00x
860-5x02-00x
12 VDC, Single or Dual
24 VDC, Single or Dual
12 VDC, Single or Dual, Low Watt
240 VDC, Single or Dual, 10 cd
Page 2
Document No: 9100-127-1112-99 REV B
Issued: April 03, 2009
Sheet 2 of 2
OBSTRUCTION / VISUAL SIGNAL LIGHT
SINGLE and DUAL FIXTURES
INSTALLATION INSTRUCTIONS and PARTS LIST
DUAL FIXTURE INSTALLATION STEPS:
• The dual housing 2B has a 1” NPT [3/4" bushing] end to be assembled to conduit.
o Use a 1-1/2” wrench to attach and tighten the dual housing 2B to the conduit
o Tighten the holding screw 3 to secure the dual housing 2B in position.
o Remove reducing bushing if threading into 1” NPT conduit
• Feed the supply wires through the conduit and dual housing 2B leaving approx 6” of wire for termination inside the dual
housing 2B .
• Electrically connect the supply wires to the light assembly 1 wires
o Connect the light assembly wire (with voltage label) to the Hot AC or Positive [+] line
o Connect the light assembly wire [without label] to the Neutral AC or Negative [-] line
o Connect the grounding wire [from green screw] to the Ground line
• Tuck the connected wires inside the dual housing. 2B .
• Position each light assembly 1 on the dual housing 2B and use the holding
• screws 3 to secure the light assembly in place
• Restore power and verify operation
Please refer to product data sheet for electrical parameters if required
U.S. Patent 6,425,678
860-4x02
PARTS LIST
Light Ass'y 240V, 50cd 860-4001 Glass Lens Replace [Clear]
Light Ass'y 240V, Australia 860-4004 Glass Lens Replace [Blue]
1" NPT Plug
Replaced glass lens will void warranties
REV ECO NO DRN CHD APP CM DATE
A -----
B 09040206 ALV KH RA JB 4/13/2009
MES KJZ JB
AV
8/22/2008
Item Part No. Description Item Part No. Description Part No. Description
860-1x01 Light Ass'y 120V 860-3x03 Light Ass'y 12V, Low Watt 860-4000 Glass Lens Replace [Red]
860-1x02
860-1x03 Light Ass'y 12V 860-5x02 Light Ass'y 240V, 10cd 860-4002 Glass Lens Replace [Green]
1 1
860-1x04 Light Ass'y 48V 860-6x01 Light Ass'y 120V, Canada 860-4003 Glass Lens Replace [Yellow]
860-1x05 Light Ass'y 24V 860-7x02
860-1x06 Light Ass'y 10-27V 860-8x04 Light Ass'y 48V, Sweden
2A 860-1000 Single W ire Housing 3 --- 1/4-20 x 1/2 Holding Screw
2B 860-2000 Dual Wire Housing 4 ---
Replace the X with color letter required … B=Blue G=Green R=Red W=White Y=Yellow
Light Ass'y 240V
5 --- 1" to 3/4" Bushing
1501 Route 34 South, Farmingdale, NJ 07727 USA Tel: [+1] 732-919-3119 Fax: [+1] 732-751-5778 www.dialight.com
Loading...