user manual
diablopaintball.com
Cover.qxd 1/10/05 10:30 AM Page 2
diablopaintball.com
Table Of Contents:
Page Topic(s)
1 Warning and Rules
Safe Marker Handling
2 Warranty Information
3 Welcome
4 Battery Installation
Powering On
Attaching Propellant Source
Attaching Feeder/Hopper
5 Loading Paintballs
Deactivating Safety
Chronographing
6 LCD Modes
Adjusting Firing Rates
Sensor
Counter
Timer
Auto Power
7 De-Gassing
Storage
Maintinence
8 Trouble Shooting Guide
9 Notes
11 Warranty Registration
Cover.qxd 1/10/05 10:30 AM Page 3
Meets or exceeds ASTM standards.
/!\ WARNING: This is not a toy. Misuse may cause seri-
ous injury or death. Eye protection designed specifically for
paintball must be worn by the user and persons within range.
Recommend 18 years of age or older to purchase. Persons
under 18 years of age must have adult supervision.
READ OWNER’S MANUAL BEFORE USING.
Rules of Safe Marker Handling
Treat every marker as if it were loaded.
Never look down the barrel of a paintball marker.
Keep your finger off the trigger until ready to shoot.
Never point the marker at anything you don’t wish to
shoot.
Keep the marker on safe until ready to shoot.
Keep the barrel blocking device in/on the marker’s muzzle when not shooting.
Always remove paintballs and propellant source before
disassembly.
After removing propellant source, point marker in safe
direction and discharge until marker is degassed.
Store the marker unloaded and de-gassed in a secure
place.
Follow warnings listed on propellant source for handling
and storage.
Do not shoot at fragile objects such as windows.
Every person within range must wear eye, face and ear
protection designed specifically to stop paintballs and
meeting ASTM standard F1776.
Always measure your marker’s velocity before playing
paintball and never shoot at velocities in excess of
91.44 meters (300 feet) per second.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
1.
1-12-2-11.qxd 1/10/05 10:24 AM Page 2
diablopaintball.com
Warranty Information
STANDARD WARRANTY:
The manufacturer warranties to the original customer that this product
is free from defects in material and workmanship under normal use
and service for a period of 90 days from the original date of purchase
by the initial owner/purchaser. The manufacturer agrees to repair or
replace (at its discretion) any product within a reasonable period of
time. This warranty does not cover: o-rings, scratches, nicks, normal
wear and tear of parts, any modifications or normal fading of anodizing or damage caused by dropping or hitting of the product. This warranty shall not apply if it is shown by the manufacture that the consumer caused the defect or malfunction because of misuse. This warranty only covers original factory parts. Any modifications or tampering
of original factory parts will not be covered by this warranty. Warranty
work can only be conducted by the manufacture technicians and or
authorized technicians. If product needs to be repair, package it carefully and send it together with your name, address, phone number and
a brief description of the malfunction to:
Paintball Solutions
570 Mantua Blvd
Sewell, NJ 08080
EXTENDED WARRANTY:
By returning the enclosed warranty registration card or
registering your warranty on-line at www.paintballsolutions.com, within fifteen days of purchase, the warranty will
automatically be extended to one year.
2.
1-12-2-11.qxd 1/10/05 10:24 AM Page 3
...Thank you, for purchasing this Wrath Paintball
marker. The Wrath represents the culmination of a great deal of
research by Diablo Paintball along with input from players such as
you. The Wrath is designed to deliver top level performance at a
reasonable cost. With its 20 ball per second cycling rate, the
Wrath is one of the fastest markers available at any price. The
Vise Grip Feed Neck, Quik-Strip bolt, vertical foregrip regulator,
ported barrel and high speed air-ram operation are all features
usually found only on much pricier markers or only through a great
deal of after-market expense. We believe that the affordability of a
reliable, feature packed marker will improve your playing experience and winning percentage. Unleash your Wrath!
Play hard, play safe, play to win!
3.
welcome
Meets or exceeds ASTM standards.
TM
3-10-4-9.qxd 1/10/05 10:27 AM Page 2
BATTERY INSTALLATION
1. Properly position barrel blocking device to prevent accidental discharge.
2. Using a 2.5mm hex wrench, remove the three Grip Panel Screws from the left
side (side facing you if the barrel is pointing to your left) of the Grip Panel.
3. Install 9 volt battery.
4. Replace Grip Panel Screws.
POWERING ON
1. Confirm that Barrel Blocking Device is properly installed.
2. Look at the LCD while pushing the button and holding until the solid line
disappears and is replaced by “BD 5 with “*******” underneath.
3. Release On/Off switch.
4. The Wrath is now “On” in “Safe Mode”
ATTACHING PROPELLANT SOURCE
1. Confirm that Barrel Blocking Device is properly installed.
2. Confirm that the LCD says “BD 5”.
3. Point the marker downward and in a safe direction.
4. Place the leading end of the propellant cylinder threads into the threaded inter
face of the (Air Source Adapter) “ASA”.
5. Without pushing, twist the propellant cylinder in a clockwise direction and allow
the cylinder threads to “draw” it into the ASA. DO NOT force the cylinder which
could cause cross threading.
6. Screw the propellant cylinder completely in until it is firmly seated
ATTACHING FEEDER/HOPPER
Due to the extremely high rate of fire capability of the Wrath, we highly recommend the use of a motorized hopper such as the Diablo TSA, Empire Reloader,
or Empire Reloader B.
1. Confirm that Barrel Blocking Device is properly installed and the
LCD says “BD 5”.
2. Twist Vise Ring in a counter-clockwise direction until it is loose but do not
remove. If accidentally removed, screw back on one complete turn.
3. Press neck of Feeder/Hopper into the Direct Feed (4) until completely seated.
4. Orient the Feeder/Hopper so that the lid is facing the rear of the
marker and the Feeder/Hopper is parallel to the Receiver.
5. Twist Vise Ring in a clockwise direction until it fits snugly against the
Feeder/Hopper neck.
4.
diablopaintball.com
3-10-4-9.qxd 1/10/05 10:27 AM Page 3
Loading Paintballs
The performance of your marker is directly related to the quality of paintballs
used. We highly recommend Diablo paintballs to give you the most satisfaction
and success on the playing field.
1. Confirm that Barrel Blocking Device is properly installed and the
LCD says “BD 5”.
2. Point marker in a safe direction and load paintballs in the Feeder/Hopper. If you
are using a non-motorized hopper, be sure to leave some room in the hopper for
the balls to feed properly.
Deactivating Safety
1. Make sure that you and anyone within range is wearing eye protection designed
specifically for paintball.
2. Confirm that Barrel Blocking Device is properly installed and the
LCD says “BD 5”.
3. Look at the LCD while pushing the button.
4. The screen will now read “Semi 15” on the top line with “000000” underneath. It
is possible that there will be numbers other than “0” on the bottom line. These
are shot counts.
5. The Wrath is now live.
Chronographing
Never operate your marker without first checking the velocity and confirming that
you are firing below that required on the field of play. At no time should the
marker fire paintballs in excess of 300 feet per second. Higher velocities are not
only potentially dangerous, they often result in a substantial increase in paint
balls broken in the marker.
1. Make sure that you and anyone within range is wearing eye protection designed
specifically for paintball.
2. Point the marker over the chronograph and in a safe direction.
3. Pull the trigger and observe the reading on the chronograph.
4. Using a 7/32 hex key adjust Vertical Regulator (VR) until pressure gauge reads
about 200 psi. You may need to fire the marker after each adjustment to allow
the gauge to adjust.
5. To increase the velocity, adjust the VR clockwise.
6. To decrease the velocity, adjust the VR counter-clockwise.
7. Replace the Barrel Blocking Device.
8. Hold down the button until the LCD blinks “Safety”.
9. The Wrath is now on Safe.
10. Keep the Wrath on Safe and Barrel Blocking Device in place until ready to play
and instructed to remove the Barrel Blocking Device by a playing field staff
member.
5.
Meets or exceeds ASTM standards.
5-8-6-7.qxd 1/10/05 10:29 AM Page 2
Meets or exceeds ASTM standards.
LCD Modes
The Diablo Wrath has a built in Anti-Chop Ball Sensor, Game Timer, Shot
Counter and can be adjusted from 4 to 20 shots per second firing rate.
Adjusting Firing Rate
1. Confirm that Barrel Blocking Device is properly installed and the
LCD says “BD 5”.
2. Press and release button.
3. “Semi 15” will appear.
4. Press and release button until desired rate of fire appears.
5. Press button to set
Sensor
1. Press button until “SENSOR” appears.
2. Press button until “OFF” or “ON” blinks.
3. Press button to set Sensor “ON” or “Off”
Counter
1. Press button until “COUNTER” appears
2. To reset press and hold button until all “0s” appear.
Timer
1. Press button until “TIMER” appears
2. To set press and arrow button until “0s” blink.
3. Press button until desired time appears (up to 99 minutes in 1 minute
increments).
4. Press button when you want to start timer count down.
Turn off marker to reset.
Auto Power
1. Press button until power appears
2. press button until “AUTO” or “ON” blinks.
3. Press button to set power to “AUTO” or “ON”.
6.
5-8-6-7.qxd 1/10/05 10:29 AM Page 3
De-Gassing
1. Make sure that you and anyone within range is wearing eye protection designed specifically for paintball.
2. Confirm that Barrel Blocking Device is properly installed and the
LCD says “BD 5” and Wrath is in “Safe Mode”.
3. Point the marker in a safe direction
4. If you are using a motorized feeder, turn it off.
5. Twist the Clamp Feed in a counter-clockwise direction until loose.
6. Invert the marker so that the hopper/feeder is upside down so
that paintballs are no longer feeding into the marker.
7. Remove the hopper/feeder from the marker.
8. While pointing the paintball marker in a safe direction, remove the
barrel blocking device.
9. Turn the Wrath on and set to fire.
10. Pull the trigger and allow the marker to cycle to confirm the
absence of paintballs in the marker’s breech. If a ball discharges,
repeat until no more paintballs come out of the marker.
/!\ WARNING: When removing the cylinder from the marker, it could fly off with
enough force to kill if the valve unscrews from the cylinder. LOOK at valve when
removing cylinder. STOP if valve starts to unscrew from the tank. Screw it back
on and take it to a trained person for repair.
11. Unscrew the propellant cylinder approximately one complete
revolution.
12. Pull the trigger until the marker fails to recock (if this takes more
than 10 shots, unscrew the cylinder an additional 1/2 turn
and repeat).
13. Remove
(See Warning Above) the propellant cylinder.
Storage
Always turn off the marker, remove the hopper/feeder, all paint balls and propel
lant source and place it in a secure location where it cannot be accessed by
unauthorized persons.
Maintenance/ Bolt
1. Pull the Bolt Pull Pin upwards until it “clicks”.
2. Pull the Bolt Pull Pin rearward until the Bolt comes out of the back of the
Receiver.
3. Clean the bolt thoroughly to include rinsing in warm water if needed.
4. Lubricate the bolt with non-corrosive lubricant such as Empire Lube or
Empire Oil.
5. Return the bolt to the rear of the Receiver making sure to put the open
end in first.
6. Slide the bolt forward until the Bolt Pull Pin lines up with the hole in the
top of the Striker.
7. Press the Bolt Pull Pin downward until it clicks in place.
7.
diablopaintball.com
5-8-6-7.qxd 1/10/05 10:29 AM Page 4
8.
diablopaintball.com
Trouble Shooting Guide
Symptom Cause Cure
When in doubt, thoroughly clean and lubricate the marker.
Many marker function problems are caused by excessive
dirt or lack of lubrication.
Does not Fire
Leaks Air
Down Barrel
Leaks Air from
ASA/Bottle Interface
Excessive Ball
Breakage
Not On
Bad Battery
Out of Gas
Bad Cup Seal
Bad Bottle O-Ring
Low Quality Paintballs
Ball Chopping
Turn Switch “On”
Replace Battery
Refill or Replace
Propellant Source
Replace Cup Seal
Replace Bottle O-Ring
Upgade Paintball Selection
(reccomendation: Diablo Brand)
Use Motorized Feeder
Such as Diablo TSA
5-8-6-7.qxd 1/10/05 10:29 AM Page 1
diablopaintball.com
10 .
Notes On Wrath:
3-10-4-9.qxd 1/10/05 10:27 AM Page 1
11.
Meets or exceeds ASTM standards.
Warranty Registration
To assist us in providing the best customer service possible and to
increase your warranty from 90 days to one year at no additional cost.
Complete and mail this to:
Paintball Solutions
570 Mantua Blvd.
Sewell, NJ 08080
Name:
Address:
City: State: Zip:
Country:
Email Address:
Serial Number (located on left side of marker):
Date of Purchase:
Place of Purchase:
Or register online at
www.PaintballSolutions.com.
1-12-2-11.qxd 1/10/05 10:24 AM Page 4
Diablo Paintball is a registered trademark of National Paintball Supply.
Diablo Paintball is ditributed exclusively through National Paintball Supply.
800. 346. 5615 / 856. 464. 1068
www.diablopaintball.com / www.nationalpaintball.com
© 2005 National Paintball Supply
Cover.qxd 1/10/05 10:30 AM Page 1
Loading...