DFI WM343-SD330, WM343-SD331 User Manual
1
Chapter 1 Introduction www.d.com
WM343-SD330/SD331
Desktop Box PC
User’s Manual
A47300805
2
Chapter 1 Introduction www.d.com
Copyright
This publication contains information that is protected by copyright. No part of it may be reproduced in any form or by any means or used to make any transformation/adaptation without
the prior written permission from the copyright holders.
This publication is provided for informational purposes only. The manufacturer makes no
representations or warranties with respect to the contents or use of this manual and specifically disclaims any express or implied warranties of merchantability or fitness for any particular purpose. The user will assume the entire risk of the use or the results of the use of this
document. Further, the manufacturer reserves the right to revise this publication and make
changes to its contents at any time, without obligation to notify any person or entity of such
revisions or changes.
Changes after the publication’s first release will be based on the product’s revision. The website will always provide the most updated information.
© 2018. All Rights Reserved.
Trademarks
Product names or trademarks appearing in this manual are for identification purpose only and
are the properties of the respective owners.
FCC and DOC Statement on Class A
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
• Consult the dealer or an experienced radio TV technician for help.
Notice:
1. The changes or modifications not expressly approved by the party responsible for compli-
ance could void the user’s authority to operate the equipment.
2. Shielded interface cables must be used in order to comply with the emission limits.
3
Chapter 1 Introduction www.d.com
Table of Contents
Copyright ���������������������������������������������������������������������� 2
Trademarks ������������������������������������������������������������������ 2
FCC and DOC Statement on Class A ���������������������������� 2
About this Manual �������������������������������������������������������� 4
Warranty ��������������������������������������������������������������������� 4
Static Electricity Precautions ��������������������������������������� 4
Safety Measures ����������������������������������������������������������� 4
Safety Precautions ������������������������������������������������������� 5
About the Package ������������������������������������������������������� 5
Before Using the System ��������������������������������������������� 5
Chapter 1 - Introduction ���������������������������������������������� 6
Chapter 2 - Getting Started ��������������������������������������� 12
Chapter 3 - Installing Devices ����������������������������������� 13
Chapter 4 - Jumper Settings ������������������������������������ 22
Clear CMOS ........................................................................... 22
Serial Port RS232/422/485 Select ...........................................23
Serial Port Power Select .........................................................25
Power-on Select ..................................................................26
Backlight Power Select (for SD330-Q170/H110 only) ...............27
Panel Power Select (for SD330-Q170/H110 only) .....................27
LCD/Inverter Power Select (for SD330-Q170/H110 only) ..........28
Mini PCIe/mSATA Signal Select (for SD330-Q170 only) ............28
Chapter 5 - Ports and Connectors ���������������������������� 29
Rear Panel I/O Ports ..............................................................29
PS/2 Keyboard/Mouse Port ..........................................................................29
COM (Serial) Ports ......................................................................................30
Graphics Interfaces .....................................................................................30
RJ45 LAN Ports ...........................................................................................31
USB Ports ...................................................................................................31
Audio ........................................................................................................ 32
I/O Connectors ...................................................................... 33
S/PDIF Connector ....................................................................................... 33
Digital I/O and Power Connector ................................................................. 34
SATA (Serial ATA) Connectors ......................................................................35
COM (Serial) Ports ......................................................................................36
USB Ports ...................................................................................................37
Cooling Fan Connectors...............................................................................38
Chassis Intrusion Connector ....................................................................... 39
LPC Connector ............................................................................................ 40
Power Connectors .......................................................................................41
SMBus Connector ...................................................................................... 42
Standby Power LED ....................................................................................43
Battery ....................................................................................................... 43
Front Panel Connector ................................................................................44
Expansion Slots .......................................................................................... 45
LVDS LCD Panel Connector .........................................................................46
Chapter 6 - Mounting Options ����������������������������������� 47
Chapter 7 - BIOS Setup ��������������������������������������������� 49
Overview .............................................................................. 49
Insyde BIOS Setup Utility .......................................................50
Main .......................................................................................................... 50
Advanced .................................................................................................. 50
Device Manager .......................................................................................... 57
Security ...................................................................................................... 62
Boot........................................................................................................... 63
Exit ............................................................................................................ 64
Updating the BIOS ................................................................. 65
Notice: BIOS SPI ROM ........................................................... 65
Chapter 8 - Supported Software �������������������������������� 66
Chapter 9 - RAID ������������������������������������������������������ 78
Chapter 10 - Intel AMT Settings ������������������������������� 82
4
Chapter 1 Introduction www.d.com
About this Manual
An electronic file of this manual is included in the CD. To view the user’s manual in the CD,
insert the CD into a CD-ROM drive. The auto-run screen (Main Board Utility CD) will appear.
Click “User’s Manual” on the main menu.
Warranty
1. Warranty does not cover damages or failures that arised from misuse of the product,
inability to use the product, unauthorized replacement or alteration of components and
product specifications.
2. The warranty is void if the product has been subjected to physical abuse, improper installation, modification, accidents or unauthorized repair of the product.
3. Unless otherwise instructed in this user’s manual, the user may not, under any circumstances, attempt to perform service, adjustments or repairs on the product, whether in or
out of warranty. It must be returned to the purchase point, factory or authorized service
agency for all such work.
4. We will not be liable for any indirect, special, incidental or consequential damages to the
product that has been modified or altered.
Static Electricity Precautions
It is quite easy to inadvertently damage your PC, system board, components or devices even
before installing them in your system unit. Static electrical discharge can damage computer
components without causing any signs of physical damage. You must take extra care in handling them to ensure against electrostatic build-up.
1. To prevent electrostatic build-up, leave the system board in its anti-static bag until you are
ready to install it.
2. Wear an antistatic wrist strap.
3. Do all preparation work on a static-free surface.
4. Hold the device only by its edges. Be careful not to touch any of the components, contacts
or connections.
5. Avoid touching the pins or contacts on all modules and connectors. Hold modules or con
nectors by their ends.
Safety Measures
To avoid damage to the system:
• Use the correct AC input voltage range.
To reduce the risk of electric shock:
• Unplug the power cord before removing the system chassis cover for installation or servic-
ing. After installation or servicing, cover the system chassis before plugging the power cord.
Battery:
• Danger of explosion if battery incorrectly replaced.
• Replace only with the same or equivalent type recommend by the manufacturer.
• Dispose of used batteries according to local ordinance.
Important:
Electrostatic discharge (ESD) can damage your processor, disk drive and other components. Perform the upgrade instruction procedures described at an ESD workstation only. If such a station is not available, you can provide some ESD protection by
wearing an antistatic wrist strap and attaching it to a metal part of the system chassis. If a wrist strap is unavailable, establish and maintain contact with the system
chassis throughout any procedures requiring ESD protection.
5
Chapter 1 Introduction www.d.com
About the Package
The package contains the following items. If any of these items are missing or damaged,
please contact your dealer or sales representative for assistance.
• 1 WM343-SD330 or WM343-SD331 System Unit
• 1 CPU cooler
• 1 SATA Data Cable (Length: 650mm)
• 4 HDD Screws
• 1 PSU Flex ATX 150W/250W/350W/400W/500W
• 1 System Fan
Optional Items
• Power Cord
• 3.5” HDD Tray Kit
The board and accessories in the package may not come similar to the information listed
above. This may differ in accordance to the sales region or models in which it was sold. For
more information about the standard package in your region, please contact your dealer or
sales representative.
Before Using the System
Before powering-on the system, prepare the basic system components.
If you are installing the system board in a new system, you will need at least the following
internal components.
• CPU and memory modules
• Storage devices such as hard disk drive, CD-ROM, etc.
You will also need external system peripherals you intend to use which will normally include at
least a keyboard, a mouse and a video display monitor.
Safety Precautions
• Use the correct DC input voltage range.
• Unplug the power cord before removing the system chassis cover for installation or servicing. After installation or servicing, cover the system chassis before plugging the power cord.
• Danger of explosion if battery incorrectly replaced.
• Replace only with the same or equivalent type recommend by the manufacturer.
• Dispose of used batteries according to local ordinance.
• Keep this system away from humidity.
• Place the system on a stable surface. Dropping it or letting it fall may cause damage.
• The openings on the system are for air ventilation to protect the system from overheating.
DO NOT COVER THE OPENINGS.
• Place the power cord in such a way that it will not be stepped on. Do not place anything on
top of the power cord. Use a power cord that has been approved for use with the system
and that it matches the voltage and current marked on the system’s electrical range label.
• If the system will not be used for a long time, disconnect it from the power source to avoid
damage by transient overvoltage.
• If one of the following occurs, consult a service personnel:
- The power cord or plug is damaged.
- Liquid has penetrated the system.
- The system has been exposed to moisture.
- The system is not working properly.
- The system dropped or is damaged.
- The system has obvious signs of breakage.
• The unit uses a three-wire ground cable which is equipped with a third pin to ground the
unit and prevent electric shock. Do not defeat the purpose of this pin. If your outlet does
not support this kind of plug, contact your electrician to replace the outlet.
• Disconnect the system from the DC outlet before cleaning. Use a damp cloth. Do not use
liquid or spray detergents for cleaning.
6
Chapter 1 Introduction www.d.com
Chapter 1 - Introduction
Chapter 1
Overview
Key Features
Model Name WM343-SD
Processor
6th Generation Intel
®
CoreTM, Pentium® and Celeron® processors
Chipset
Intel
®
C236 / Q170 / H110 Chipset
LAN
2 LAN ports
COM
1 COM port
Displays
1 x VGA
1 x DVI-I (DVI-D signal)
1 x DP++
USB 4 USB 3.0 ports + 2 USB 2.0 ports
Audio
Mic-in, Line-out, Line-in (available upon request)
Front View
Rear View
7
Chapter 1 Introduction www.d.com
Specifications
Chapter 1
System Processor 6th Generation Intel® CoreTM Processors (LGA 1151 Socket)
Intel
®
Xeon® Processor E3-1275 v5, Quad Core, 8M Cache,
3.6GHz (4.0GHz), 80W
Intel
®
Xeon® Processor E3-1225 v5, Quad Core, 6M Cache,
3.3GHz (3.7GHz), 80W
Intel
®
Xeon® Processor E3-1268L v5, Quad Core, 8M Cache,
2.4GHz (3.4GHz), 35W
Intel
®
Core™ i7-6700 Processor, Quad Core, 8M Cache,
3.4GHz (4.0GHz), 65W
Intel
®
Core™ i7-6700TE Processor, Quad Core, 8M Cache,
2.4GHz (3.4GHz), 35W
Intel
®
Core™ i5-6500 Processor, Quad Core, 6M Cache,
3.2GHz (3.6GHz), 65W
Intel® Core™ i5-6500TE Processor, Quad Core, 6M Cache,
2.3GHz (3.3GHz), 35W
Intel
®
Core™ i3-6100 Processor, Dual Core, 4M Cache, 65W
Intel
®
Core™ i3-6100TE Processor, Dual Core, 4M Cache,
2.7GHz, 35W
Intel
®
Pentium® Processor G4400, Dual Core, 3M Cache,
3.3GHz, 65W
Intel
®
Pentium® Processor G4400TE, Dual Core, 3M Cache,
2.9GHz, 35W
Intel® Celeron® Processor G3900, Dual Core, 2M Cache,
2.8GHz, 65W
Intel
®
Celeron® Processor G3900TE, Dual Core, 2M Cache,
2.6GHz, 35W
Chipset WM343-SD330
SD330-Q170: Intel
®
Q170 Chipset
SD330-H110: Intel
®
H110 Chipset
WM343-SD331
SD331-C236: Intel
®
C236 Chipset
SD331-Q170: Intel
®
Q170 Chipset
Memory WM343-SD331 (SD331-C236/SD331-Q170)
Four 288-pin ECC/non-ECC DIMM up to 64GB, dual channel DDR4
1866/2133MHz
WM343-SD330 (SD330-Q170)
Four 288-pin DIMM up to 64GB, dual channel DDR4 1866/2133MHz
WM343-SD330 (SD330-H110):
Two 288-pin DIMM up to 32GB, dual channel DDR4 1866/2133MHz
Graphics Controller Intel® HD Gen 9 Graphics
Feature OpenGL 5.0, DirectX 12, OpenCL 2.1
HW Decode: AVC/H.264, MPEG2, VC1/WMV9, JPEG/MJPEG, HEVC/H265, VP8, VP9
HW Encode: MPEG2, AVC/H264, JPEG, HEVC/H265, VP8, VP9
Display 1 x VGA
1 x DVI-I (DVI-D signal)
1 x DP++
1 x LVDS (only for SD330-Q170/SD330-H110)
VGA: resolution up to 1920x1200 @ 60Hz
DVI-I: resolution up to 1920x1200 @ 60Hz
DP++: resolution up to 4096x2304 @ 60Hz
LVDS: dual channel, resolution up to 1920x1200 @ 60Hz
Triple
Display
VGA + DVI-I (DVI-D signal) + DP++
Storage External 1 or 2 x 3.5"/2.5" SATA 3.0 Drive Bays (1 x 3.5" SATA drive bay, by default)
1 x 5.25" Optical Drive Bay
Expansion Interface WM343-SD330
1 x PCIe x16 (Gen 3)
1 x PCIe x4 (Gen 3)
2 x PCI
1 x Full-size Mini PCIe (USB/PCIe/mSATA, PCIe by default) (only for
SD330-Q170)
WM343-SD331
2 x PCIe x16 (1 x16 or 2 x8 signal) (Gen 3)
2 x PCIe x4 (Gen 3)
Audio Codec Realtek ALC888S-VD2-GR
8
Chapter 1 Introduction www.d.com
Environment Operating
Temperature
0 to 45°C
Storage
Temperature
0 to 60°C
Relative
Humidity
5 to 95% RH (non-condensing)
Mechanical Shock Operating: 3G
Non-operating: 5G
Vibration Operating: Random 5~500Hz 0.5G
Non-operating: Sine 10~500Hz 1.5G
Package
Drop
ISTA Project 1A
Chapter 1
WatchDog
Timer
Output &
Interval
System Reset, Programmable via Software from 1 to 255 Seconds
Power Supply Flex ATX 250W (or optional 150/250/350/400/500W)
OS Support
and BIOS
OS Windows 7 (/WES7) 32/64-bit
Windows 8.1 (64-bit)
Windows 10 IoT Enterprise 64-bit
Debian 8 (with VESA graphics driver)
CentOS 7 (with VESA graphics driver)
Ubuntu 15.10 (Intel graphics driver available)
BIOS Insyde SPI 128Mbit
Mechanical Construction Sheet Metal
Compliance Wall Mount
Dimensions 349mm x 140.2mm x 290.9mm (13.74" x 5.52" x 11.45")
Weight TBD
ETHERNET Controller 1 x Intel® I210AT PCIe (10/100/1000Mbps)
1 x Intel
®
I219LM PCIe with iAMT11.0 (10/100/1000Mbps)
LED Indicators 1 x Power LED
1 x HDD LED
REAR I/O Ethernet 2 x GbE (RJ-45)
Serial 1 x RS-232/422/485 (RS-232 w/ power) (DB-9)
USB 4 x USB 3.0
2 x USB 2.0
PS/2 1 x PS/2 (mini-DIN-6)
Display 1 x VGA
1 x DVI-I (DVI-D signal)
1 x DP++
Audio 1 x Line-out, 1 x Mic-in, 1 x Line-in (available upon request)
Buttons 1 x Power Button
Cooling Fan 1 x System Fan
9
Chapter 1 Introduction www.d.com
DVI-I/DP++/VGA Port
Connects the DVI-I (DVI-D signal)/DP++/VGA connector of an LCD monitor.
COM Port
Connects serial devices. COM 1 can be selected among RS232, RS422 and RS485 as well as
between RS232 and RS232 with power via jumper settings.
USB 3�0 Ports
Connect USB 3.0 devices and devices based on USB 2.0 and 1.1/1.0 versions.
USB 2�0 Ports
Connect USB 2.0 devices and devices based on USB 1.1/1.0 versions.
LAN Ports
Connect the system to a local area network.
Line-out
Connects an external speaker.
Line-in (optional)
Connects any audio devices such as CD players, audio mixers, musical instruments, etc.
Mic-in
Connects an external microphone.
PS/2 KB/Mouse
Connects a PS/2 keyboard and mouse.
Expansion slots
Provides PCIe or PCI expansion connectivity.
Power Button
Press to power on or off the system.
Status LED (Green)
Indicates system status.
HDD LED (Red)
Indicates the status of hard drives.
SATA Drive Bay
Inserts a SATA drive.
Optical Drive Bay
Inserts a DVD or CD-ROM. Note that this bay can also be an optional 3.5” SATA drive bay.
Chapter 1
Getting to Know the WM343-SD
Front View
Status LED
ACPI state S0 Sleep S4, S5
LED Behavior
ON Blinking Off
HDD LED
HDD State
Disk access
activity
Disk drives present or not present
LED Behavior
Blinking Off
Rear View
Power Button
Optical
Drive Bay
SATA
Drive Bay
Expansion
Slots
USB 3.0 Ports
DVI-I
DP++
PS/2 Keyboard/Mouse
USB 2.0 Ports
COM
VGA
Line-in (optional)
Line-out
Mic-in
HDD LED
Status LED
LAN Ports
10
Chapter 1 Introduction www.d.com
349
140.20
290.9
Mechanical Dimensions (WM343-SD330)
Chapter 1
349
140.20
290.9
Front View
Right View
Left View
Rear View
Mechanical Dimensions (WM343-SD331)
Front View
Right ViewLeft View
Rear View
11
Chapter 1 Introduction www.d.com
Chapter 1
Motherboard Dimensions (SD330-Q170)
209.55
10.16
0.00
45.72
203.20
22.86
154.94
227.33
46.94
29.22
47.29
34.29
160.23
205.33
154.94
233.68
227.33
180.23
150.29
75.29
94.79
130.79
165.82
90.81
0.00
45.72
13.67
26.97
20.32
Motherboard Dimensions (SD331-C236/SD331-Q170)
Motherboard Dimensions (SD330-H110)
209.55
0.00
10.16
0.00
45.72
45.72
203.20
22.86
154.94
227.33
46.94
29.22
47.29
13.67
26.97
34.29
160.23
205.33
154.94
233.68
227.33
180.23
150.29
75.29
94.79
130.79
165.82
90.81
209.55
0.00
10.16
0.00
45.72
20.32
45.72
203.20
22.86
154.94
227.33
46.94
47.29
26.97
13.67
34.29
160.23
205.33
154.94
233.68
227.33
180.23
150.29
75.29
94.79
130.79
165.82
90.81
197.48
171.73
135.39
105.13
82.63
63.46
12
Chapter 2 Getting Started www.d.com
Preparing the System
Before you start using the system, you need the following items:
• SATA hard drive
• CPU
• PS/2 or USB keyboard
• PS/2 or USB mouse
• CD-ROM drive (for installing software/drivers)
• Screwdriver
• Memory modules (optional)
Installing Devices
The following devices can be installed in the system.
• Memory modules
• SATA hard drive
Configuring the BIOS
To get you started, you may need to change configurations such as the date, time and the type of
hard disk drive.
1. Power on the system.
2. After the memory test, the message “Press DEL to run setup” will appear on the screen.
Press the Delete key to enter the BIOS setup utility.
Installing the Operating System
Most operating system software can be installed using a DVD (and DVD burner) or bootable USB
drive.
Please refer to your operating system manual for instructions on installing an operating system.
Installing the Drivers
The system comes with a software package including drivers. These drivers must be installed to
provide the best system performance. Refer to the Supported Software Chapter for instructions on
installing drivers.
Chapter 2 - Getting Started
Chapter 2
www.d.com
13
Chapter 3 Installing Devices
Chapter 3
Chapter 3 - Installing Devices
Opening the Chassis
Please observe the following guidelines and follow the procedure to open the system.
1. Make sure the system and all other peripheral devices connected to it have been powered off.
2. Disconnect all power cords and cables.
3. Remove the top cover by uninstalling the thumb screws.
Thumb screw
Installing a DIMM
To access the DIMM sockets, rst remove the optical drive tray by uninstalling the screws from
the rear panel and inside the chassis.
Optical drive
tray screw
Optical drive tray screw
www.d.com
14
Chapter 3 Installing Devices
Chapter 3
1. Align the notch on the DIMM with the tab in the DIMM socket.
2. Press down on the DIMM until the release tabs spring back to secure the DIMM in place.
The installed DIMM
Installing a CPU
1.
Make sure the system and all other peripheral devices connected to it have been powered-off.
2. Disconnect all power cords and cables.
3. The system board is equipped with a surface mount LGA 1151 socket. This socket is exclusively designed for installing a LGA 1151 packaged Intel CPU.
Important:
1. Before you proceed, make sure (1) the LGA 1151 socket comes with a protective
cap, (2) the cap is not damaged and (3) the socket’s contact pins are not bent. If
the cap is missing or the cap or contact pins are damaged, contact your dealer immediately.
2. Keep the protective cap. RMA requests will be accepted and processed only if the
LGA 1151 socket comes with the protective cap.
4. Unlock the socket by pushing the load lever down, move it sideways until it is released
from the retention tab, and then lift the load lever up.
Protective
cap
Load lever
www.d.com
15
Chapter 3 Installing Devices
Chapter 3
5. Remove the protective cap from the CPU socket. The cap is used to protect the CPU socket against dust and harmful particles. Remove the protective cap only to install the CPU.
6. Insert the CPU into the socket. The gold triangular mark on the CPU must align with the
corner of the CPU socket as the photo shown below.
7. Unlock the socket by pushing the load lever down and moving it sideways until it is released from the retention tab and then lift the load lever up.
8. Insert the CPU into the socket. The gold triangular mark on the CPU must align with the
corner of the CPU socket as shown below. The CPU’s notch will at the same time fit into
the socket’s alignment key.
Alignment key
Gold triangular mark
Retention tab
Protective
cap
Load lever
Load plate
Important:
The CPU will fit in only one orientation and can easily be inserted without exerting
any force.
9. Close the load plate and push the load lever down to lock it under the retention tab. While
closing the load plate, slide the front edge of the load plate under the retention tab.
Retention knob
www.d.com
16
Chapter 3 Installing Devices
Chapter 3
Installing the Fan and Heat Sink
The CPU must be kept cool by using a CPU fan with heat sink. Without sufficient air circulation across the CPU and heat sink, the CPU will overheat damaging both the CPU and
system board.
1. Before you install the fan / heat sink, you must apply a thermal paste onto the top of
the CPU. The thermal paste is usually supplied when you purchase the fan / heat sink
assembly. Do not spread the paste all over the surface. When you later place the heat
sink on top of the CPU, the compound will disperse evenly.
Some heat sinks come with a patch of pre-applied thermal paste. Do not apply thermal
paste if the fan / heat sink already has a patch of thermal paste on its underside. Peel
the strip that covers the paste before you place the fan / heat sink on top of the CPU.
2. Place the heat sink on top
of the CPU. The 4 screw
around the heat sink,
which are used to secure
the heat sink onto the system board, must match the
4 mounting holes around
the socket.
3. Orient the heat sink such
that the CPU fan’s cable is
nearest the CPU fan connector.
Note:
A boxed Intel® processor already includes the CPU fan and heat sink assembly.
If your CPU was purchased separately, make sure to only use Intel®-certified fan
and heat sink.
Mounting hole
CPU fan connector
4. Rotate each screw that are
diagonally across the heat sink.
Perform the same procedure
for the other screws.
5. Connect the CPU fan’s cable
to the CPU fan connector on
the system board.
Heat sink
“Locked” position
of the screw
“Unlocked” position
of the screw
CPU fan connector
www.d.com
17
Chapter 3 Installing Devices
Chapter 3
Installing a 2�5" SATA Drive
Use the same HDD drive tray to secure a 2.5" hard disk to the system. Refer to the pictures below
for the location of mounting holes.
Mounting screw
Mounting screw
Installing a 3�5" SATA Drive
1. Remove the thumb screws that secure the HDD drive tray to the chassis and remove the
drive tray.
Thumb screw
2. Secure the hard drive to the drive tray. Align the mounting holes on the SATA drive with the
mounting holes on the HDD drive tray. Use 4 mounting screws to install the hard drive onto
the HDD drive tray.
Drive bay
Mounting screw
Mounting screw
www.d.com
18
Chapter 3 Installing Devices
Chapter 3
Installing More Than One SATA Drive (Optional)
To install more than one 2.5" SATA drive, use the 5.25" optical drive tray. And to install more than
one 3.5" SATA drive, please order another HDD drive tray as shown in the following procedure.
Use the following procedure to install a second 3.5" HDD/SSD:
Drive bay
Mounting screw
Mounting screw
1. Secure the hard drive to the drive tray. Align the mounting holes on the SATA drive with the
mounting holes on the HDD drive tray. Use 4 mounting screws to install the hard drive onto
the HDD drive tray.
2. Slide the HDD drive tray with the installed hard drive into the optical drive bay and secure
the installation with the thumb screws.
For 3�5" SATA Drives
1. Slide the HDD drive tray back to the system and secure it with the thumb screws.
2. Connect the SATA data cable and power cable to the connectors on the SATA drive. And con
-
nect the other end of the SATA data cable on the motherboard.
SATA data and
power cable
www.d.com
19
Chapter 3 Installing Devices
Chapter 3
3. Install the optical drive tray back to the system.
4. Connect the SATA data cable and power cable to the connectors on the SATA drive. And connect
the other end of the SATA data cable on the motherboard.
SATA data and
power cable
SATA data and
power cable
SATA Port
1. Attach 4 standoffs to the 2.5" HDD or SSD.
Mounting screw
Mounting screw
2. Secure the hard drive to the optical drive tray. Align the standoffs on the HDD with the
mounting holes on the optical drive tray. Use 4 mounting screws to install the hard drive
onto the optical drive tray.
Mounting screw
Mounting screw
Use the following procedure to install a second and third 2.5” HDD/SSD:
For 2�5" SATA Drives
www.d.com
20
Chapter 3 Installing Devices
Chapter 3
Installing a PCI or PCIe Expansion Card
Use the following procedure to install a PCIe expansion card:
1. Remove the mounting screws to uninstall the card slot bracket.
Screw
Card slot bracket
2. Insert the expansion card in the connector on the
motherboard
and press down until secured.
PCIe card
Rear View
PCIe card
3. Reinstall the card slot bracket to secure the expansion card in place.
Notes:
1. The WM343-SD330 is equipped with one PCIe x16, one PCIe x4 and two PCI slots.
2. The WM343-SD331 is equipped with two PCIe x16 and two PCIe x4 slots.
www.d.com
21
Chapter 3 Installing Devices
Chapter 3
Installing a Mini PCIe Card
The system board is equipped with one Mini PCIe slot that uses USB, PCI and mSATA signals.
1. Grasp the Mini PCIe card by its edges and align the notch in the connector of the PCIe
card with the notch in the connector on the system board.
2. Push the Mini PCIe card down and use the provided mounting screws to secure the card on
the system board.
Note:
The Mini PCIe slot is only available in WM343-SD330 (Intel
®
Q170 Chipset).
22
Chapter 4 Jumper Settings
Chapter 4
www.d.com
Chapter 4 - Jumper Settings
If you encounter the following situations, you can reconfigure the system with the default
values stored in the ROM BIOS.
a) CMOS data becomes corrupted.
b) You forgot the supervisor or user password.
To load the default values stored in the ROM BIOS, please follow these steps below:
1. Power off the system and unplug the power cord.
2. Set the jumper pins 2 and 3 to On. Wait for a few seconds and set the jumper pins back
to its default setting, pins 1 and 2 On.
3. Now plug the power cord and power on the system.
JP1
COM 2 RS232/422/485
Select (JP13)
COM 2 RS232/Power
Select (JP14)
COM 2 RS232/422/485
Select (JP11)
COM 2 RS232/422/485
Select (JP12)
COM 1 RS232/422/485
Select (JP8)
COM 1
RS232/422/485
Select (JP10)
COM 1
RS232/422/485
Select (JP7)
Intel
Q170
1
256
SMBus
+12V
Power
154
8
PCIe 2 (PCIe x4)
PCIe 4 (PCIe x4)
Standby
Power LED
PCIe 1 (PCIe x16 or PCIe x8)
PCIe 3 (PCIe x8)
1
ATX
Power
12 24
13
1 2
11 12
Front
Panel
1 2
LAN LED
7 8
PS/2 KB/MS
USB 6
USB 5
USB 2.0
DVI-D
DP++
LAN 1
USB 2
USB 1
USB 3.0
LAN 2
USB 4
USB 3
USB 3.0
I C
Line-out
Mic-in
Socket LGA1151
21
1314
LPC
TPM
(optional)
USB 3.0
Battery
Buzzer
Chassis
Intrusion
1
SPI Flash
BIOS
1
1
1
1
1
1
SATA 1
SATA 3
SATA 5
SATA 0
SATA 2
SATA 4
SATA 3.0
1
S/PDIF
1
Clear CMOS
Data (JP1)
DDR4_1 DDR4_3
DDR4_4DDR4_2
System Fan 2
1
Auto Power-on
Select (JP5)
1
CPU Fan
1
System Fan 1
1
1
2
19
DIO
1
210
9 1
210
9 1
210
9 1
210
9 1
210
9
COM 5
COM 2
COM 6
COM 3 COM 4
1
210
9
USB 7-8
USB 2.0
125612
56
12
56
12
56
516251
62
516251
62
COM 1
VGA
11
10
1
11
10
1
COM 1 RS232/Power
Select (JP9)
USB 5-6 USB 7-8
Nuvoton
NCT6106D
Realtek
ALC888
Intel
WGI219LM
Intel
WGI210AT
ASMedia
ASM1442
Chrontel
CH7517A
1
210
9
USB 9-10
1-2 On: Normal
(default)
31 2
2-3 On:
Clear CMOS Data
31 2
WM343-SD330 (H110)
WM343-SD330 (Q170)
Clear CMOS
WM343-SD331 (C236/Q170)
DVI-D
DP++
COM 1
VGA
DDR4_1 DDR4_3
DDR4_4DDR4_2
1
Clear CMOS
Data (JP1)
1
SATA 0
1
SATA 1
1
SATA 2
1
SATA 3
SATA 3.0
Chassis
Intrusion
1
11
10
1
USB 5-6
USB 2.0
1
210
9
USB 7-8
1
2 40
39
LVDS LCD Panel
1
LCD/Inverter Power
Intel
WGI219LM
Intel
WGI210AT
ASMedia
ASM1442
Chrontel
CH7517A
1
ATX
Power
12 24
13
1 2
11 12
1 2
7 8
Auto Power-on
Select (JP5)
1
Realtek
ALC888
1
1
256
SMBus
1 2
7 8
SPI
Program
Header
LAN LED
Front
Panel
1
210
9
USB 9-10
LCD/Inverter
Power Select (JP4)
Backlight Power
Select (JP3)
Panel Power Select (JP2)
Mini PCIe/mSATA
Signal Select (JP6)
NXP
PTN3460
1
System
Fan 2
SPI Flash
BIOS
Line-out
Mic-in
LAN 1
USB 2
USB 1
USB 3.0
LAN 2
USB 4
USB 3
USB 3.0
PS/2 KB/MS
USB 6
USB 5
USB 2.0
USB 3.0
Socket LGA1151
Standby
Power LED
Intel
Q170
TPM
(optional)
21
1314
LPC
+12V
Power
154
8
Buzzer
1
S/PDIF
1
210
9
1
210
9 1
210
9 1
210
9 1
210
9
COM 5 COM 6COM 2 COM 3 COM 4
1
2
19
Digital I/O
CPU Fan
1
System Fan 1
1
PCI 1
PCI 2
PCIe x4
ITE
IT8893E
PCIe x16
Battery
1
1
12
56
5162516251
62
51
62
516251
62
516251
62
COM 2 RS232/Power
Select (JP14)
(JP13) (JP11)
(JP12)
Nuvoton
NCT6106D
COM 1 RS232/485
Select (JP8)
COM 1 RS232/485
Select (JP10)
COM 1 RS232/Power
Select (JP9)
COM 1
RS232/422/485
Select (JP7)
1-2 On: Normal
(default)
31 2
2-3 On:
Clear CMOS Data
31 2
JP1
DVI-D
DP++
COM 1
VGA
DDR4_1 DDR4_3
1
Clear CMOS
Data (JP1)
1
SATA 0
1
SATA 1
1
SATA 2
1
SATA 3
SATA 3.0
Chassis
Intrusion
1
USB 2.0
1
210
9
USB 7-8
1
2 40
39
LVDS LCD Panel
1
LCD/Inverter Power
Intel
WGI219LM
Intel
WGI210AT
ASMedia
ASM1442
Chrontel
CH7517A
1
ATX
Power
12 24
13
1 2
11 12
Front
Panel
1 2
LAN LED
7 8
Auto Power-on
Select (JP5)
1
Realtek
ALC888
1
1
256
SMBus
USB 9/10
14
SPI Flash
BIOS
Line-out
Mic-in
LAN 1
USB 2
USB 1
USB 3.0
LAN 2
USB 4
USB 3
USB 3.0
PS/2 KB/MS
USB 6
USB 5
USB 2.0
1
2
8
7
ON
3
4
2
1
1
3
Socket LGA1151
Standby
Power LED
Intel
H110
TPM
(optional)
21
1314
LPC
+12V
Power
154
8
Buzzer
1
210
9
1
210
9 1
210
9 1
210
9 1
210
9
COM 5 COM 6COM 2 COM 3 COM 4
1
2
19
Digital I/O
CPU Fan
1
System Fan 1
1
PCI 1
PCI 2
PCIe x4
Nuvoton
NCT6106D
PCIe x16
Battery
1
1
12
56
5162516251
62
51
62
516251
62
516251
62
COM 2 RS232/Power
Select (JP14)
(JP13) (JP11)
1
System
Fan 2
(JP12)
J6
SW1
JP4
JP3
JP2
J26
JP6
R507R505
COM 1 RS232/485
Select (JP8)
COM 1 RS232/485
Select (JP10)
COM 1 RS232/Power
Select (JP9)
COM 1
RS232/422/485
Select (JP7)
1
S/PDIF
JP1
1-2 On: Normal
(default)
31 2
2-3 On:
Clear CMOS Data
31 2
23
Chapter 4 Jumper Settings
Chapter 4
www.d.com
WM343-SD330 (H110)
WM343-SD330 (Q170)
JP7 (COM 1) / JP11 (COM 2)
COM 1
RS232
DCD
TXD
RXD
DTR
GND
1
2 3 4 5
RTS
RI
DSR
CTS
6 7 8 9
RS485
DATA+
N.C.
DATA-
N.C.
GND
1 2 3 4 5
N.C.
N.C.
N.C.
N.C.
6 7 8 9
RS422
Full Duplex
RXD+
TXD+
RXD-
TXD-
GND
1 2 3 4 5
N.C.
N.C.
N.C.
N.C.
6 7 8 9
1-2 On: RS232
(default)
2 4 6
1 3 5
3-4 On: RS422
Full Duplex
2 4 6
1 3 5
5-6 On: RS485
2 4 6
1 3 5
JP8 and JP10 (COM 1) / JP12 and JP13 (COM 2)
JP7, JP8, and JP10 (for COM 1) and JP11, JP12, and JP13 (for COM 2) are used to configure
the COM ports to RS232, RS422 (full duplex) or RS485. The pin assignments of the COM ports
will vary according to the jumper settings.
2 4 6
1 3 5
2 4 6
1 3 5
1-3, 2-4 On: RS232
(default)
3-5, 4-6 On:
RS422 Full Duplex/ RS485
COM 2
RS232
RXD
DCD
TXD
DTR
GND
DSR
RTS
CTS
RI
2
1
9
10
NC.
NC.
NC.
RXD-
RXD+
TXD+
TXD-
NC.
NC.
NC.
2
1
9
10
RS422
Full Duplex
RS485
2 4 6
1 3 5
JP7,
JP10, JP8
DVI-D
DP++
COM 1
VGA
DDR4_1 DDR4_3
1
Clear CMOS
Data (JP1)
1
SATA 0
1
SATA 1
1
SATA 2
1
SATA 3
SATA 3.0
Chassis
Intrusion
1
USB 2.0
1
210
9
USB 7-8
1
2 40
39
LVDS LCD Panel
1
LCD/Inverter Power
Intel
WGI219LM
Intel
WGI210AT
ASMedia
ASM1442
Chrontel
CH7517A
1
ATX
Power
12 24
13
1 2
11 12
Front
Panel
1 2
LAN LED
7 8
Auto Power-on
Select (JP5)
1
Realtek
ALC888
1
1
256
SMBus
USB 9/10
14
SPI Flash
BIOS
Line-out
Mic-in
LAN 1
USB 2
USB 1
USB 3.0
LAN 2
USB 4
USB 3
USB 3.0
PS/2 KB/MS
USB 6
USB 5
USB 2.0
1
2
8
7
ON
3
4
2
1
1
3
Socket LGA1151
Standby
Power LED
Intel
H110
TPM
(optional)
21
1314
LPC
+12V
Power
154
8
Buzzer
1
210
9
1
210
9 1
210
9 1
210
9 1
210
9
COM 5 COM 6COM 2 COM 3 COM 4
1
2
19
Digital I/O
CPU Fan
1
System Fan 1
1
PCI 1
PCI 2
PCIe x4
Nuvoton
NCT6106D
PCIe x16
Battery
1
1
12
56
5162516251
62
51
62
516251
62
516251
62
COM 2 RS232/Power
Select (JP14)
(JP13) (JP11)
1
System
Fan 2
(JP12)
J6
SW1
JP4
JP3
JP2
J26
JP6
R507R505
COM 1 RS232/485
Select (JP8)
COM 1 RS232/485
Select (JP10)
COM 1 RS232/Power
Select (JP9)
COM 1
RS232/422/485
Select (JP7)
1
S/PDIF
JP13, JP12, JP11
2 4 6
1 3 5
2 4 6
1 3 5
2 4 6
1 3 5
DATA+
NC.
NC.
NC.
NC.
NC.
NC.
2
1
9
10
DATA-
NC.
DVI-D
DP++
COM 1
VGA
DDR4_1 DDR4_3
DDR4_4DDR4_2
1
Clear CMOS
Data (JP1)
1
SATA 0
1
SATA 1
1
SATA 2
1
SATA 3
SATA 3.0
Chassis
Intrusion
1
11
10
1
USB 5-6
USB 2.0
1
210
9
USB 7-8
1
2 40
39
LVDS LCD Panel
1
LCD/Inverter Power
Intel
WGI219LM
Intel
WGI210AT
ASMedia
ASM1442
Chrontel
CH7517A
1
ATX
Power
12 24
13
1 2
11 12
1 2
7 8
Auto Power-on
Select (JP5)
1
Realtek
ALC888
1
1
256
SMBus
1 2
7 8
SPI
Program
Header
LAN LED
Front
Panel
1
210
9
USB 9-10
LCD/Inverter
Power Select (JP4)
Backlight Power
Select (JP3)
Panel Power Select (JP2)
Mini PCIe/mSATA
Signal Select (JP6)
NXP
PTN3460
1
System
Fan 2
SPI Flash
BIOS
Line-out
Mic-in
LAN 1
USB 2
USB 1
USB 3.0
LAN 2
USB 4
USB 3
USB 3.0
PS/2 KB/MS
USB 6
USB 5
USB 2.0
USB 3.0
Socket LGA1151
Standby
Power LED
Intel
Q170
TPM
(optional)
21
1314
LPC
+12V
Power
154
8
Buzzer
1
S/PDIF
1
210
9
1
210
9 1
210
9 1
210
9 1
210
9
COM 5 COM 6COM 2 COM 3 COM 4
1
2
19
Digital I/O
CPU Fan
1
System Fan 1
1
PCI 1
PCI 2
PCIe x4
ITE
IT8893E
PCIe x16
Battery
1
1
12
56
5162516251
62
51
62
516251
62
516251
62
COM 2 RS232/Power
Select (JP14)
(JP13) (JP11)
(JP12)
Nuvoton
NCT6106D
COM 1 RS232/485
Select (JP8)
COM 1 RS232/485
Select (JP10)
COM 1 RS232/Power
Select (JP9)
COM 1
RS232/422/485
Select (JP7)
JP13, JP12, JP11
JP7,
JP10, JP8
Serial Port RS232/422/485 Select
24
Chapter 4 Jumper Settings
Chapter 4
www.d.com
WM343-SD331 (C236/Q170)
JP7, JP8, and JP10 (for COM1) and JP11, JP12, and JP13 (for COM2) are used to configure the
COM ports to RS232, RS422 (full duplex) or RS485. The pin assignments of the COM ports will
vary according to the jumper settings.
JP7 (COM 1) / JP11 (COM 2)
COM 1
RS232
DCD
TXD
RXD
DTR
GND
1
2 3 4 5
RTS
RI
DSR
CTS
6 7 8 9
RS485
DATA+
N.C.
DATA-
N.C.
GND
1 2 3 4 5
N.C.
N.C.
N.C.
N.C.
6 7 8 9
RS422
Full Duplex
RXD+
TXD+
RXD-
TXD-
GND
1 2 3 4 5
N.C.
N.C.
N.C.
N.C.
6 7 8 9
JP8 and JP10 (COM 1) / JP12 and JP13 (COM 2)
COM 2
RS232
RXD
DCD
TXD
DTR
GND
DSR
RTS
CTS
RI
2
1
9
10
NC.
NC.
NC.
RXD-
RXD+
TXD+
TXD-
NC.
NC.
NC.
2
1
9
10
RS422
Full Duplex
DATA+
TXD
NC.
NC.
NC.
NC.
NC.
NC.
2
1
9
10
DATA-
RS485
COM 2 RS232/422/485
Select (JP13)
COM 2 RS232/Power
Select (JP14)
COM 2 RS232/422/485
Select (JP11)
COM 2 RS232/422/485
Select (JP12)
COM 1 RS232/422/485
Select (JP8)
COM 1
RS232/422/485
Select (JP10)
COM 1
RS232/422/485
Select (JP7)
Intel
Q170
1
256
SMBus
+12V
Power
154
8
PCIe 2 (PCIe x4)
PCIe 4 (PCIe x4)
Standby
Power LED
PCIe 1 (PCIe x16 or PCIe x8)
PCIe 3 (PCIe x8)
1
ATX
Power
12 24
13
1 2
11 12
Front
Panel
1 2
LAN LED
7 8
PS/2 KB/MS
USB 6
USB 5
USB 2.0
DVI-D
DP++
LAN 1
USB 2
USB 1
USB 3.0
LAN 2
USB 4
USB 3
USB 3.0
I C
Line-out
Mic-in
Socket LGA1151
21
1314
LPC
TPM
(optional)
USB 3.0
Battery
Buzzer
Chassis
Intrusion
1
SPI Flash
BIOS
1
1
1
1
1
1
SATA 1
SATA 3
SATA 5
SATA 0
SATA 2
SATA 4
SATA 3.0
1
S/PDIF
1
Clear CMOS
Data (JP1)
DDR4_1 DDR4_3
DDR4_4DDR4_2
System Fan 2
1
Auto Power-on
Select (JP5)
1
CPU Fan
1
System Fan 1
1
1
2
19
DIO
1
210
9 1
210
9 1
210
9 1
210
9 1
210
9
COM 5
COM 2
COM 6
COM 3 COM 4
1
210
9
USB 7-8
USB 2.0
125612
56
12
56
12
56
516251
62
516251
62
COM 1
VGA
11
10
1
11
10
1
COM 1 RS232/Power
Select (JP9)
USB 5-6 USB 7-8
Nuvoton
NCT6106D
Realtek
ALC888
Intel
WGI219LM
Intel
WGI210AT
ASMedia
ASM1442
Chrontel
CH7517A
1
210
9
USB 9-10
JP12, JP13, JP11
JP7,
JP10, JP8
2 4 6
1 3 5
1
526
1-2 On: RS232
(default)
2 4 6
1 3 5
1
526
3-4 On: RS422
Full Duplex
2 4 6
1 3 5
5
6
2
1
5-6 On: RS485
2 4 6
1 3 5
5
6
2
1
1-3, 2-4 On: RS232
(default)
1
526
2 4 6
1 3 5
3-5, 4-6 On:
RS422 Full Duplex/ RS485
1
526
2 4 6
1 3 5
25
Chapter 4 Jumper Settings
Chapter 4
www.d.com
1-3 (RI), 2-4 (DCD) On:
RS232 (default)
3-5 (+5V), 4-6 (+12V) On:
RS232 with power
Serial Port Power Select
WM343-SD330 (H110)
WM343-SD330 (Q170)
COM 2 RS232/422/485
Select (JP13)
COM 2 RS232/Power
Select (JP14)
COM 2 RS232/422/485
Select (JP11)
COM 2 RS232/422/485
Select (JP12)
COM 1 RS232/422/485
Select (JP8)
COM 1
RS232/422/485
Select (JP10)
COM 1
RS232/422/485
Select (JP7)
Intel
Q170
1
256
SMBus
+12V
Power
154
8
PCIe 2 (PCIe x4)
PCIe 4 (PCIe x4)
Standby
Power LED
PCIe 1 (PCIe x16 or PCIe x8)
PCIe 3 (PCIe x8)
1
ATX
Power
12 24
13
1 2
11 12
Front
Panel
1 2
LAN LED
7 8
PS/2 KB/MS
USB 6
USB 5
USB 2.0
DVI-D
DP++
LAN 1
USB 2
USB 1
USB 3.0
LAN 2
USB 4
USB 3
USB 3.0
I C
Line-out
Mic-in
Socket LGA1151
21
1314
LPC
TPM
(optional)
USB 3.0
Battery
Buzzer
Chassis
Intrusion
1
SPI Flash
BIOS
1
1
1
1
1
1
SATA 1
SATA 3
SATA 5
SATA 0
SATA 2
SATA 4
SATA 3.0
1
S/PDIF
1
Clear CMOS
Data (JP1)
DDR4_1 DDR4_3
DDR4_4DDR4_2
System Fan 2
1
Auto Power-on
Select (JP5)
1
CPU Fan
1
System Fan 1
1
1
2
19
DIO
1
210
9 1
210
9 1
210
9 1
210
9 1
210
9
COM 5
COM 2
COM 6
COM 3 COM 4
1
210
9
USB 7-8
USB 2.0
125612
56
12
56
12
56
516251
62
516251
62
COM 1
VGA
11
10
1
11
10
1
COM 1 RS232/Power
Select (JP9)
USB 5-6 USB 7-8
Nuvoton
NCT6106D
Realtek
ALC888
Intel
WGI219LM
Intel
WGI210AT
ASMedia
ASM1442
Chrontel
CH7517A
1
210
9
USB 9-10
WM343-SD331 (C236/Q170)
JP9
2 4 6
1 3 5
JP14
1
526
1
5
2
6
JP9 (for COM1) and JP14 (for COM2) are used to switch the COM ports to RS232 or RS232
with power. The pin assignments of the COM ports will vary according to the jumper settings.
RS232
DCD
(or 12V)
TXD
RXD
DTR
GND
1
2 3 4 5
RTS
RI
(or 5V)
DSR
CTS
6 7 8 9
2 4 6
1 3 5
2 4 6
1 3 5
1
5
2
6
DVI-D
DP++
COM 1
VGA
DDR4_1 DDR4_3
DDR4_4DDR4_2
1
Clear CMOS
Data (JP1)
1
SATA 0
1
SATA 1
1
SATA 2
1
SATA 3
SATA 3.0
Chassis
Intrusion
1
11
10
1
USB 5-6
USB 2.0
1
210
9
USB 7-8
1
2 40
39
LVDS LCD Panel
1
LCD/Inverter Power
Intel
WGI219LM
Intel
WGI210AT
ASMedia
ASM1442
Chrontel
CH7517A
1
ATX
Power
12 24
13
1 2
11 12
1 2
7 8
Auto Power-on
Select (JP5)
1
Realtek
ALC888
1
1
256
SMBus
1 2
7 8
SPI
Program
Header
LAN LED
Front
Panel
1
210
9
USB 9-10
LCD/Inverter
Power Select (JP4)
Backlight Power
Select (JP3)
Panel Power Select (JP2)
Mini PCIe/mSATA
Signal Select (JP6)
NXP
PTN3460
1
System
Fan 2
SPI Flash
BIOS
Line-out
Mic-in
LAN 1
USB 2
USB 1
USB 3.0
LAN 2
USB 4
USB 3
USB 3.0
PS/2 KB/MS
USB 6
USB 5
USB 2.0
USB 3.0
Socket LGA1151
Standby
Power LED
Intel
Q170
TPM
(optional)
21
1314
LPC
+12V
Power
154
8
Buzzer
1
S/PDIF
1
210
9
1
210
9 1
210
9 1
210
9 1
210
9
COM 5 COM 6COM 2 COM 3 COM 4
1
2
19
Digital I/O
CPU Fan
1
System Fan 1
1
PCI 1
PCI 2
PCIe x4
ITE
IT8893E
PCIe x16
Battery
1
1
12
56
5162516251
62
51
62
516251
62
516251
62
COM 2 RS232/Power
Select (JP14)
(JP13) (JP11)
(JP12)
Nuvoton
NCT6106D
COM 1 RS232/485
Select (JP8)
COM 1 RS232/485
Select (JP10)
COM 1 RS232/Power
Select (JP9)
COM 1
RS232/422/485
Select (JP7)
JP14
JP9
1
526
2 4 6
1 3 5
DVI-D
DP++
COM 1
VGA
DDR4_1 DDR4_3
1
Clear CMOS
Data (JP1)
1
SATA 0
1
SATA 1
1
SATA 2
1
SATA 3
SATA 3.0
Chassis
Intrusion
1
USB 2.0
1
210
9
USB 7-8
1
2 40
39
LVDS LCD Panel
1
LCD/Inverter Power
Intel
WGI219LM
Intel
WGI210AT
ASMedia
ASM1442
Chrontel
CH7517A
1
ATX
Power
12 24
13
1 2
11 12
Front
Panel
1 2
LAN LED
7 8
Auto Power-on
Select (JP5)
1
Realtek
ALC888
1
1
256
SMBus
USB 9/10
14
SPI Flash
BIOS
Line-out
Mic-in
LAN 1
USB 2
USB 1
USB 3.0
LAN 2
USB 4
USB 3
USB 3.0
PS/2 KB/MS
USB 6
USB 5
USB 2.0
1
2
8
7
ON
3
4
2
1
1
3
Socket LGA1151
Standby
Power LED
Intel
H110
TPM
(optional)
21
1314
LPC
+12V
Power
154
8
Buzzer
1
210
9
1
210
9 1
210
9 1
210
9 1
210
9
COM 5 COM 6COM 2 COM 3 COM 4
1
2
19
Digital I/O
CPU Fan
1
System Fan 1
1
PCI 1
PCI 2
PCIe x4
Nuvoton
NCT6106D
PCIe x16
Battery
1
1
12
56
5162516251
62
51
62
516251
62
516251
62
COM 2 RS232/Power
Select (JP14)
(JP13) (JP11)
1
System
Fan 2
(JP12)
J6
SW1
JP4
JP3
JP2
J26
JP6
R507R505
COM 1 RS232/485
Select (JP8)
COM 1 RS232/485
Select (JP10)
COM 1 RS232/Power
Select (JP9)
COM 1
RS232/422/485
Select (JP7)
1
S/PDIF
JP9
JP14
1
526
2 4 6
1 3 5
26
Chapter 4 Jumper Settings
Chapter 4
www.d.com
COM 2 RS232/422/485
Select (JP13)
COM 2 RS232/Power
Select (JP14)
COM 2 RS232/422/485
Select (JP11)
COM 2 RS232/422/485
Select (JP12)
COM 1 RS232/422/485
Select (JP8)
COM 1
RS232/422/485
Select (JP10)
COM 1
RS232/422/485
Select (JP7)
Intel
Q170
1
256
SMBus
+12V
Power
154
8
PCIe 2 (PCIe x4)
PCIe 4 (PCIe x4)
Standby
Power LED
PCIe 1 (PCIe x16 or PCIe x8)
PCIe 3 (PCIe x8)
1
ATX
Power
12 24
13
1 2
11 12
Front
Panel
1 2
LAN LED
7 8
PS/2 KB/MS
USB 6
USB 5
USB 2.0
DVI-D
DP++
LAN 1
USB 2
USB 1
USB 3.0
LAN 2
USB 4
USB 3
USB 3.0
I C
Line-out
Mic-in
Socket LGA1151
21
1314
LPC
TPM
(optional)
USB 3.0
Battery
Buzzer
Chassis
Intrusion
1
SPI Flash
BIOS
1
1
1
1
1
1
SATA 1
SATA 3
SATA 5
SATA 0
SATA 2
SATA 4
SATA 3.0
1
S/PDIF
1
Clear CMOS
Data (JP1)
DDR4_1 DDR4_3
DDR4_4DDR4_2
System Fan 2
1
Auto Power-on
Select (JP5)
1
CPU Fan
1
System Fan 1
1
1
2
19
DIO
1
210
9 1
210
9 1
210
9 1
210
9 1
210
9
COM 5
COM 2
COM 6
COM 3 COM 4
1
210
9
USB 7-8
USB 2.0
125612
56
12
56
12
56
516251
62
516251
62
COM 1
VGA
11
10
1
11
10
1
COM 1 RS232/Power
Select (JP9)
USB 5-6 USB 7-8
Nuvoton
NCT6106D
Realtek
ALC888
Intel
WGI219LM
Intel
WGI210AT
ASMedia
ASM1442
Chrontel
CH7517A
1
210
9
USB 9-10
Power-on Select
1-2 On:
Power-on via power button
(default)
2-3 On:
Power-on via AC power or
WOL after power interruption
1 2 3
1 2 3
DVI-D
DP++
COM 1
VGA
DDR4_1 DDR4_3
1
Clear CMOS
Data (JP1)
1
SATA 0
1
SATA 1
1
SATA 2
1
SATA 3
SATA 3.0
Chassis
Intrusion
1
USB 2.0
1
210
9
USB 7-8
1
2 40
39
LVDS LCD Panel
1
LCD/Inverter Power
Intel
WGI219LM
Intel
WGI210AT
ASMedia
ASM1442
Chrontel
CH7517A
1
ATX
Power
12 24
13
1 2
11 12
Front
Panel
1 2
LAN LED
7 8
Auto Power-on
Select (JP5)
1
Realtek
ALC888
1
1
256
SMBus
USB 9/10
14
SPI Flash
BIOS
Line-out
Mic-in
LAN 1
USB 2
USB 1
USB 3.0
LAN 2
USB 4
USB 3
USB 3.0
PS/2 KB/MS
USB 6
USB 5
USB 2.0
1
2
8
7
ON
3
4
2
1
1
3
Socket LGA1151
Standby
Power LED
Intel
H110
TPM
(optional)
21
1314
LPC
+12V
Power
154
8
Buzzer
1
210
9
1
210
9 1
210
9 1
210
9 1
210
9
COM 5 COM 6COM 2 COM 3 COM 4
1
2
19
Digital I/O
CPU Fan
1
System Fan 1
1
PCI 1
PCI 2
PCIe x4
Nuvoton
NCT6106D
PCIe x16
Battery
1
1
12
56
5162516251
62
51
62
516251
62
516251
62
COM 2 RS232/Power
Select (JP14)
(JP13) (JP11)
1
System
Fan 2
(JP12)
J6
SW1
JP4
JP3
JP2
J26
JP6
R507R505
COM 1 RS232/485
Select (JP8)
COM 1 RS232/485
Select (JP10)
COM 1 RS232/Power
Select (JP9)
COM 1
RS232/422/485
Select (JP7)
1
S/PDIF
WM343-SD330 (H110)
WM343-SD330 (Q170)
JP5
1 2 3
DVI-D
DP++
COM 1
VGA
DDR4_1 DDR4_3
DDR4_4DDR4_2
1
Clear CMOS
Data (JP1)
1
SATA 0
1
SATA 1
1
SATA 2
1
SATA 3
SATA 3.0
Chassis
Intrusion
1
11
10
1
USB 5-6
USB 2.0
1
210
9
USB 7-8
1
2 40
39
LVDS LCD Panel
1
LCD/Inverter Power
Intel
WGI219LM
Intel
WGI210AT
ASMedia
ASM1442
Chrontel
CH7517A
1
ATX
Power
12 24
13
1 2
11 12
1 2
7 8
Auto Power-on
Select (JP5)
1
Realtek
ALC888
1
1
256
SMBus
1 2
7 8
SPI
Program
Header
LAN LED
Front
Panel
1
210
9
USB 9-10
LCD/Inverter
Power Select (JP4)
Backlight Power
Select (JP3)
Panel Power Select (JP2)
Mini PCIe/mSATA
Signal Select (JP6)
NXP
PTN3460
1
System
Fan 2
SPI Flash
BIOS
Line-out
Mic-in
LAN 1
USB 2
USB 1
USB 3.0
LAN 2
USB 4
USB 3
USB 3.0
PS/2 KB/MS
USB 6
USB 5
USB 2.0
USB 3.0
Socket LGA1151
Standby
Power LED
Intel
Q170
TPM
(optional)
21
1314
LPC
+12V
Power
154
8
Buzzer
1
S/PDIF
1
210
9
1
210
9 1
210
9 1
210
9 1
210
9
COM 5 COM 6COM 2 COM 3 COM 4
1
2
19
Digital I/O
CPU Fan
1
System Fan 1
1
PCI 1
PCI 2
PCIe x4
ITE
IT8893E
PCIe x16
Battery
1
1
12
56
5162516251
62
51
62
516251
62
516251
62
COM 2 RS232/Power
Select (JP14)
(JP13) (JP11)
(JP12)
Nuvoton
NCT6106D
COM 1 RS232/485
Select (JP8)
COM 1 RS232/485
Select (JP10)
COM 1 RS232/Power
Select (JP9)
COM 1
RS232/422/485
Select (JP7)
JP5
1 2 3
JP5
1 2 3
WM343-SD331 (C236/Q170)
JP5 is used to select the method of powering on the system. If you want the system to
power on whenever AC power comes in, set the jumper pins 2 and 3 to On. If you want to use
the power button, set the jumper pins 1 and 2 to On.
27
Chapter 4 Jumper Settings
Chapter 4
www.d.com
DVI-D
DP++
COM 1
VGA
DDR4_1 DDR4_3
DDR4_4DDR4_2
1
Clear CMOS
Data (JP1)
1
SATA 0
1
SATA 1
1
SATA 2
1
SATA 3
SATA 3.0
Chassis
Intrusion
1
11
10
1
USB 5-6
USB 2.0
1
210
9
USB 7-8
1
2 40
39
LVDS LCD Panel
1
LCD/Inverter Power
Intel
WGI219LM
Intel
WGI210AT
ASMedia
ASM1442
Chrontel
CH7517A
1
ATX
Power
12 24
13
1 2
11 12
1 2
7 8
Auto Power-on
Select (JP5)
1
Realtek
ALC888
1
1
256
SMBus
1 2
7 8
SPI
Program
Header
LAN LED
Front
Panel
1
210
9
USB 9-10
LCD/Inverter
Power Select (JP4)
Backlight Power
Select (JP3)
Panel Power Select (JP2)
Mini PCIe/mSATA
Signal Select (JP6)
NXP
PTN3460
1
System
Fan 2
SPI Flash
BIOS
Line-out
Mic-in
LAN 1
USB 2
USB 1
USB 3.0
LAN 2
USB 4
USB 3
USB 3.0
PS/2 KB/MS
USB 6
USB 5
USB 2.0
USB 3.0
Socket LGA1151
Standby
Power LED
Intel
Q170
TPM
(optional)
21
1314
LPC
+12V
Power
154
8
Buzzer
1
S/PDIF
1
210
9
1
210
9 1
210
9 1
210
9 1
210
9
COM 5 COM 6COM 2 COM 3 COM 4
1
2
19
Digital I/O
CPU Fan
1
System Fan 1
1
PCI 1
PCI 2
PCIe x4
ITE
IT8893E
PCIe x16
Battery
1
1
12
56
5162516251
62
51
62
516251
62
516251
62
COM 2 RS232/Power
Select (JP14)
(JP13) (JP11)
(JP12)
Nuvoton
NCT6106D
COM 1 RS232/485
Select (JP8)
COM 1 RS232/485
Select (JP10)
COM 1 RS232/Power
Select (JP9)
COM 1
RS232/422/485
Select (JP7)
Backlight Power Select (for SD330-Q170/H110 only) Panel Power Select (for SD330-Q170/H110 only)
JP3 is used to select the power level of backlight brightness control.
JP3
Backlight Power Select JP3
+3.3V (default) 1-2 On
+5V 2-3 On
3
2
1
Panel Power Select JP2
+12V 1-2 On
+5V 3-4 On
+3.3V (default) 5-6 On
DVI-D
DP++
COM 1
VGA
DDR4_1 DDR4_3
DDR4_4DDR4_2
1
Clear CMOS
Data (JP1)
1
SATA 0
1
SATA 1
1
SATA 2
1
SATA 3
SATA 3.0
Chassis
Intrusion
1
11
10
1
USB 5-6
USB 2.0
1
210
9
USB 7-8
1
2 40
39
LVDS LCD Panel
1
LCD/Inverter Power
Intel
WGI219LM
Intel
WGI210AT
ASMedia
ASM1442
Chrontel
CH7517A
1
ATX
Power
12 24
13
1 2
11 12
1 2
7 8
Auto Power-on
Select (JP5)
1
Realtek
ALC888
1
1
256
SMBus
1 2
7 8
SPI
Program
Header
LAN LED
Front
Panel
1
210
9
USB 9-10
LCD/Inverter
Power Select (JP4)
Backlight Power
Select (JP3)
Panel Power Select (JP2)
Mini PCIe/mSATA
Signal Select (JP6)
NXP
PTN3460
1
System
Fan 2
SPI Flash
BIOS
Line-out
Mic-in
LAN 1
USB 2
USB 1
USB 3.0
LAN 2
USB 4
USB 3
USB 3.0
PS/2 KB/MS
USB 6
USB 5
USB 2.0
USB 3.0
Socket LGA1151
Standby
Power LED
Intel
Q170
TPM
(optional)
21
1314
LPC
+12V
Power
154
8
Buzzer
1
S/PDIF
1
210
9
1
210
9 1
210
9 1
210
9 1
210
9
COM 5 COM 6COM 2 COM 3 COM 4
1
2
19
Digital I/O
CPU Fan
1
System Fan 1
1
PCI 1
PCI 2
PCIe x4
ITE
IT8893E
PCIe x16
Battery
1
1
12
56
5162516251
62
51
62
516251
62
516251
62
COM 2 RS232/Power
Select (JP14)
(JP13) (JP11)
(JP12)
Nuvoton
NCT6106D
COM 1 RS232/485
Select (JP8)
COM 1 RS232/485
Select (JP10)
COM 1 RS232/Power
Select (JP9)
COM 1
RS232/422/485
Select (JP7)
JP2 is used to select the power supply of the LCD panel.
2 4 6
1 3 5
JP2
28
Chapter 4 Jumper Settings
Chapter 4
www.d.com
LCD/Inverter Power Select (for SD330-Q170/H110 only)
LCD/Inverter Power Select JP4
+12V (default) 1-2 On
+5V 2-3 On
Mini PCIe/mSATA Signal Select JP6
Mini PCIe (default) 1-2 On
mSATA 2-3 On
DVI-D
DP++
COM 1
VGA
DDR4_1 DDR4_3
DDR4_4DDR4_2
1
Clear CMOS
Data (JP1)
1
SATA 0
1
SATA 1
1
SATA 2
1
SATA 3
SATA 3.0
Chassis
Intrusion
1
11
10
1
USB 5-6
USB 2.0
1
210
9
USB 7-8
1
2 40
39
LVDS LCD Panel
1
LCD/Inverter Power
Intel
WGI219LM
Intel
WGI210AT
ASMedia
ASM1442
Chrontel
CH7517A
1
ATX
Power
12 24
13
1 2
11 12
1 2
7 8
Auto Power-on
Select (JP5)
1
Realtek
ALC888
1
1
256
SMBus
1 2
7 8
SPI
Program
Header
LAN LED
Front
Panel
1
210
9
USB 9-10
LCD/Inverter
Power Select (JP4)
Backlight Power
Select (JP3)
Panel Power Select (JP2)
Mini PCIe/mSATA
Signal Select (JP6)
NXP
PTN3460
1
System
Fan 2
SPI Flash
BIOS
Line-out
Mic-in
LAN 1
USB 2
USB 1
USB 3.0
LAN 2
USB 4
USB 3
USB 3.0
PS/2 KB/MS
USB 6
USB 5
USB 2.0
USB 3.0
Socket LGA1151
Standby
Power LED
Intel
Q170
TPM
(optional)
21
1314
LPC
+12V
Power
154
8
Buzzer
1
S/PDIF
1
210
9
1
210
9 1
210
9 1
210
9 1
210
9
COM 5 COM 6COM 2 COM 3 COM 4
1
2
19
Digital I/O
CPU Fan
1
System Fan 1
1
PCI 1
PCI 2
PCIe x4
ITE
IT8893E
PCIe x16
Battery
1
1
12
56
5162516251
62
51
62
516251
62
516251
62
COM 2 RS232/Power
Select (JP14)
(JP13) (JP11)
(JP12)
Nuvoton
NCT6106D
COM 1 RS232/485
Select (JP8)
COM 1 RS232/485
Select (JP10)
COM 1 RS232/Power
Select (JP9)
COM 1
RS232/422/485
Select (JP7)
Mini PCIe/mSATA Signal Select (for SD330-Q170 only)
31 2
JP4 is used to select the power level of the LCD/inverter power connector.
31 2
DVI-D
DP++
COM 1
VGA
DDR4_1 DDR4_3
DDR4_4DDR4_2
1
Clear CMOS
Data (JP1)
1
SATA 0
1
SATA 1
1
SATA 2
1
SATA 3
SATA 3.0
Chassis
Intrusion
1
11
10
1
USB 5-6
USB 2.0
1
210
9
USB 7-8
1
2 40
39
LVDS LCD Panel
1
LCD/Inverter Power
Intel
WGI219LM
Intel
WGI210AT
ASMedia
ASM1442
Chrontel
CH7517A
1
ATX
Power
12 24
13
1 2
11 12
1 2
7 8
Auto Power-on
Select (JP5)
1
Realtek
ALC888
1
1
256
SMBus
1 2
7 8
SPI
Program
Header
LAN LED
Front
Panel
1
210
9
USB 9-10
LCD/Inverter
Power Select (JP4)
Backlight Power
Select (JP3)
Panel Power Select (JP2)
Mini PCIe/mSATA
Signal Select (JP6)
NXP
PTN3460
1
System
Fan 2
SPI Flash
BIOS
Line-out
Mic-in
LAN 1
USB 2
USB 1
USB 3.0
LAN 2
USB 4
USB 3
USB 3.0
PS/2 KB/MS
USB 6
USB 5
USB 2.0
USB 3.0
Socket LGA1151
Standby
Power LED
Intel
Q170
TPM
(optional)
21
1314
LPC
+12V
Power
154
8
Buzzer
1
S/PDIF
1
210
9
1
210
9 1
210
9 1
210
9 1
210
9
COM 5 COM 6COM 2 COM 3 COM 4
1
2
19
Digital I/O
CPU Fan
1
System Fan 1
1
PCI 1
PCI 2
PCIe x4
ITE
IT8893E
PCIe x16
Battery
1
1
12
56
5162516251
62
51
62
516251
62
516251
62
COM 2 RS232/Power
Select (JP14)
(JP13) (JP11)
(JP12)
Nuvoton
NCT6106D
COM 1 RS232/485
Select (JP8)
COM 1 RS232/485
Select (JP10)
COM 1 RS232/Power
Select (JP9)
COM 1
RS232/422/485
Select (JP7)
JP4
JP6
JP6 is used to select the signal for the Mini PCIe socket.
Mini PCIe Socket
29
Chapter 5 Ports and Connectors
Chapter 5
www.d.com
Chapter 5 - Ports and Connectors
Rear Panel I/O Ports
The rear panel I/O consists of the following ports:
• 1 PS/2 Keyboard/Mouse port
• 1 Serial port
• 1 VGA
• 1 DVI-I (DVI-D Signal) port
• 1 DisplayPort
• 2 RJ45 LAN ports
• 4 USB 3.0 ports
• 2 USB 2.0 ports
• Line-in jack (optional)
• Line-out jack
• Microphone jack
PS/2 Keyboard/Mouse Port
These ports are used to connect a PS/2 mouse/keyboard.
Wake-On PS/2 Keyboard/Mouse
The Wake-On-PS/2 Keyboard/Mouse function allows you to use the PS/2 keyboard or PS/2
mouse to power on the system. To use this function, configure the wake-up function of PS/2
keyboard/mouse in the Advanced menu (“ACPI Configuration” submenu) of the BIOS. Refer to
Chapter 7 for more information.
DVI
LAN 1 LAN 2
COM 1
VGA
DP++
USB 3.0
PS/2 KB/MS
USB 2.0
Line-out
Mic-in
PS/2 Keyboard/Mouse
Note:
This port cannot work with a PS/2 mouse alone. To connect both keyboard and
mouse, please use a PS/2 keyboard mouse splitter cable adapter.
Loading...