DFI PB60-VB User Manual

PB60-VB

Rev. B+
System Board
Users Manual

37200839

Copyright

This publication contains information that is protected by copyright. No
part of it may be reproduced in any form or by any means or used to
make any transformation/adaptation without the prior written permission
from the copyright holders.

This publication is provided for informational purposes only. The
manufacturer makes no representations or warranties with respect to
the contents or use of this manual and specifically disclaims any express
or implied warranties of merchantability or fitness for any particular purpose.
The user will assume the entire risk of the use or the results of the use of
this document. Further, the manufacturer reserves the right to revise this
publication and make changes to its contents at any time, without obligation
to notify any person or entity of such revisions or changes.

© 1998. All Rights Reserved.

Trademarks

Microsoft® MS-DOS®, WindowsTM and Windows® 95 are registered
trademarks of Microsoft Corporation. Intel®, Pentium® II and Celeron

TM

are registered trademarks of Intel Corporation. Award is a registered
trademark of Award Software, Inc. Other trademarks and registered
trademarks of products appearing in this manual are the proper ties of
their respective holders.

Caution:

Danger of explosion if battery incorrectly replaced.
Replace only with the same or equivalent type recommended by the
manufacturer.
Dispose of used batteries according to the battery manufacturers
instructions.

FCC and DOC Statement on Class B

This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC rules.
These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a residential
installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio
communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:

 Reorient or relocate the receiving antenna.
 Increase the separation between the equipment and the receiver.
 Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

 Consult the dealer or an experienced radio TV technician for

help.

Notice:

1. The changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority
to operate the equipment.

2. Shielded interface cables must be used in order to comply with
the emission limits.

Table of Contents

Chapter 1 - Introduction

1.1 Features and Specifications ......................................................................

1.2 Package Checklist .........................................................................................

Chapter 2 - Hardware Installation

2.1 System Board Layout .................................................................................

2.2 System Memory .............................................................................................

2.3 DIP Switch Settings of the Processors ............................................

2.4 Jumper Settings for CPU Front Side Bus .......................................

2.5 Jumper Settings for CMOS Clear .......................................................

2.6 Jumper Settings for Wake-On-Keyboard/Mouse........................

2.7 Connecting the Ribbon Cables and Wires of the Ports

and Connectors .............................................................................................

Chapter 3 - Award BIOS Setup Utility

3.1 The Basic Input/Output System ...........................................................

3.1.1 Standard CMOS Setup.............................................................

3.1.2 BIOS Features Setup..................................................................

3.1.3 Chipset Features Setup.............................................................

3.1.4 Power Management Setup......................................................

3.1.5 PNP/PCI Configuration .............................................................

3.1.6 Load Fail-Safe Settings ...............................................................

3.1.7 Load Optimal Settings ..............................................................

3.1.8 Integrated Peripherals .................................................................

3.1.9 Supervisor Password ..................................................................

3.1.10 User Password...............................................................................

3.1.11 IDE HDD Auto Detection .....................................................

3.1.12 Save & Exit Setup ........................................................................

3.1.13 Exit Without Saving .....................................................................

6

10

11
12
12
14
15
16

17

28
28
32
35
38
42
43
44
44
49
49
50
51
51

Chapter 4 - Supported Softwares

4.1 Desktop Management Interface ..........................................................

4.2 System Health Monitor Utility ................................................................

4.3 Drivers ................................................................................................................

Appendix A - System Error Messages

A.1 POST Beep ......................................................................................................

A.2 Error Messages ...............................................................................................

Appendix B - Troubleshooting

B.1 Troubleshooting Checklist. ........................................................................

52
55
56

57
57

59

Chapter 1 - Introduction

1.1 Features and Specifications

1.1.1 Features

Chipset

 VIA BX Plus AGPset

Processor

The system board is equipped with a 242-pin Intel Slot 1
processor slot for installing an Intel Pentium II processor that is
packaged in an SEC (Single Edge Contact) cartridge or an Intel
CeleronTM processor.

 233/66MHz, 266/66MHz, 300/66MHz, 333/66MHz,

350/100MHz, 400/100MHz or 450/100MHz Pentium II
processor with 512KB L2 cache

 266/66MHz, 300/66MHz, 300A/66MHz, 333/66MHz or

366/66MHz Intel CeleronTM processor

System Memory

The system board supports 8MB to 384MB memory. It is equipped
with three 168-pin DIMM sockets using x64/x72 unbuffered PC
SDRAM, 3.3V. The PC SDRAMs supported are PC-66 SDRAM for
66MHz/100MHz FSB and PC-100 SDRAM for 100MHz FSB. The
system board also supports ECC (uses x72 PC SDRAM).

Expansion Slots

The system board is equipped with 1 dedicated AGP slot, 3
dedicated PCI slots, 2 dedicated 16-bit ISA slots and 1 shared PCI/
ISA slot. All PCI and ISA slots are bus masters.

Desktop Management Interface (DMI)

The system board comes with a DMI 2.0 built into the BIOS. The
DMI utility in the BIOS automatically records various information

6

Introduction

about your system configuration and stores these information in the
DMI pool, which is a par t of the system board's Plug and Play
BIOS. DMI, along with the appropriately networked software, is
designed to make inventory, maintenance and troubleshooting of
computer systems easier. Refer to Chapter 4 for instructions on
using the DMI utility.

Onboard I/O

 Two NS16C550A-compatible DB-9 serial por ts
 One SPP/ECP/EPP DB-25 parallel port
 One floppy drive interface supports up to two 2.88MB floppy

drives

 One mini-DIN-6 PS/2 mouse port
 One mini-DIN-6 PS/2 keyboard port
 One WOL (Wake-On-LAN) connector

PCI Bus Master IDE Controller

 Two PCI IDE interfaces support up to four IDE devices
 Ultra DMA/33 supported (Synchronous Ultra DMA mode -

data transfer rate up to a maximum of 33MB/sec.)

 PIO Mode 3 and Mode 4 Enhanced IDE (data transfer rate up

to 16.6MB/sec.)

 Bus mastering reduces CPU utilization during disk transfer
 ATAPI CD-ROM supported
 LS-120 and ZIP supported

1

IrDA Interface

The system board is equipped with an IrDA connector for wireless
connectivity between your computer and peripheral devices. It
supports peripheral devices that meet the IrDA or ASKIR standard.

USB Ports

The system board is equipped with two USB ports. USB allows
data exchange between your computer and a wide range of
simultaneously accessible external Plug and Play peripherals.

7

1

Introduction

BIOS

 Award BIOS, Windows 95 Plug and Play compatible
 Flash EPROM for easy BIOS upgrades

1.1.2 Intelligence

Monitors Processor Temperature and Overheat Alarm

The system board is able to detect the temperature of the
processor. An alarm will sound in case of processor overheat. Refer
to Chipset Features Setup (Chapter 3) and System Health Monitor
Utility (Chapter 4).

Monitors Processor/Chassis Fan Speed and Failure Alarm

The system board is able to detect the fan speed (RPM-Revolution
Per Minute) and aler ts you to attend to any irregularity that may
damage your system. Refer to Chipset Features Setup (Chapter 3)
and System Health Monitor Utility (Chapter 4).

Monitors Power Voltages and Failure Alarm

The system board is able to detect the output voltage of the power
supply. An alarm will sound warning you of voltage irregularity. Refer
to Chipset Features Setup (Chapter 3) and System Health Monitor
Utility (Chapter 4).

Automatic Fan Control

With the systems power switched on, the processors fan will rotate
only if the temperature of the processor is over 25oC. This saves
energy, prevents system overheat, prolongs fan life and implements a
silent system.

Dual Function Power Button

Depending on the setting in the BIOS setup, this switch will allow
your system to enter the Soft-Off or Suspend mode.

8

Introduction

External Modem Ring-on

The Modem Ring-on feature allows the system that is in the
Suspend mode or Soft Power Off mode to wake-up/power-on to
respond to incoming calls.

Note:

This feature supports external modem only.

RTC Timer to Power-On the System

The RTC installed on the system board allows your system to
automatically power-on on the set date and time.

Wake-On-LAN Ready

The Wake-On-LAN function allows the network to remotely wake
up a Soft Power Down (Soft-Off) PC. Your LAN card must support
the remote wakeup function.

Important:

The 5VSB power source of your power supply must support
720mA (minimum).

1

Wake-On-Keyboard/Wake-On-Mouse

This function allows you to use the keyboard or mouse to power-on
the system. Refer to Jumper Settings for Wake-On-Keyboard/Wake­On-Mouse in Chapter 2 and Keyboard/Mouse Power On in the
Integrated Peripherals setup of the Award BIOS in Chapter 3 for
more information.

Important:

The power button will not function once a keyboard password
has been set in the KB Power On Password field of the
Integrated Peripherals setup. You must type the password to
power-on the system.

Virus Protection

Most viruses today destroy data stored in hard drives. The system
board is designed to protect the boot sector and partition table of
your hard disk drive.

9

1

Introduction

1.2 Package Checklist

The system board package contains the following items:

þ The system board
þ A users manual
þ One 40-pin IDE hard disk cable
þ One 34-pin floppy disk drive cable
þ One CD

If any of these items are missing or damaged, please contact your
dealer or sales representative for assistance.

10

Chapter 2 - Hardware Installation

2.1 System Board Layout

11

2

Hardware Installation

2.2 System Memory

2.3 DIP Switch Settings of the Processors

The table below shows the supported processors and their
corresponding DIP switch settings (SW1). There are 4 switches on
SW1. The black rectangle in the diagram denotes the par t that is
protruding, the adjustable switch. Make sure SW1 is set correctly
before applying power, otherwise you will not be able to power-on
the system.

12

In the example above:

Switch 1: Off
Switch 2: Off
Switch 3: On
Switch 4: On

Hardware Installation

2

Processor

66MHz 100MHz

233MHz 350MHz 3.5x

266MHz 400MHz 4x

300MHz 450MHz 4.5x

333MHz Future processor 5x

366MHz Future processor 5.5x

Future processor Future processor 6x

Future processor Future processor 6.5x

Frequency Ratio

SW1

Future processor Future processor 7x

Future processor Future processor 7.5x

Future processor Future processor 8x

Note:

Intel Pentium II processor or Intel CeleronTM processor
supports VID (Voltage Identification). The switching voltage
regulator on the system board will automatically set the
voltage regulator according to the voltage of the processor.

13

2

Hardware Installation

2.4 Jumper Settings for CPU Front Side Bus

Jumper JP3

CPU Front Side Bus Select

The default is set at 1-2 On, Auto.
The system will automatically set the
bus speed according to the FSB of
the processor. If it is Off, FSB is set
to 100MHz.

Warning:

If you set JP3 to Off for 66MHz FSB processor, it will provide better
system performance. However, we do not guarantee that the system
will work properly.

14

Off : 100MHzOn : Auto(default)

Hardware Installation

2.5 Jumper Settings for CMOS Clear

Jumper JP5

CMOS Clear

If, for some reason, the CMOS data
becomes corrupted, the system can
be reconfigured with the default
values stored in the ROM BIOS. To
load the default values, power-off your
system and unplug the power cord.
Set JP5 pins 2 and 3 to On. Wait for
a few seconds and set JP5 back to
its default setting, pins 1 and 2 On.
You may now plug the power cord
and power-on your system.

2

1-2 On:

Normal (default)

2-3 On:

Clear CMOS Data

15

2

Hardware Installation

2.6 Jumper Settings for Wake-On-Keyboard/
Wake-On-Mouse

Jumper JP7
Wake-On-Keyboard/Wake-On-Mouse

The system board supports the Wake­On-Keyboard/Wake-On-Mouse function.
This function allows the keyboard or
mouse to power-on the system. By de­fault, JP7 is disabled. Make sure Key­board/Mouse Power On in the Inte­grated Peripherals setup of the Award
BIOS is also disabled.

2-3 On: Enable1-2 On: Disable (default)

16

Warning:

1. If JP7 was previously enabled with a password set in the
BIOS setup, and now you wish to disable the Wake-On-Key­board function, make sure to disable the password in the
BIOS setup prior to setting JP7 to disabled. You will not be
able to boot up the system if you fail to do so.

2. The power button will not function once a keyboard
password has been set in the KB Power On Password field
of the Integrated Peripherals setup. You must type the
passwrod to power-on the system.

3. The 5VSB power source of your power supply must support
720mA (minimum).

Hardware Installation

2.7 Connecting the Ribbon Cables and Wires
of the Ports and Connectors

2.7.1 Serial Ports

The built-in serial ports are RS-232C
asynchronous communication ports
with 16C550A-compatible UARTs that
can be used with modems, serial
printers, remote display terminals, and
other serial devices. You can set the
serial ports I/O address in the
Integrated Peripherals setup of the
Award BIOS.

2.7.2 PS/2 Mouse Port

2

The PS/2 mouse port uses IRQ12. If a
mouse is not connected to this port, the
system will reserve IRQ12 for other
expansion cards.

17

2

Hardware Installation

2.7.3 Parallel Port

The system board has a standard printer
port for interfacing your PC to a parallel
printer. It supports SPP, ECP and EPP
modes. You can set the ports mode in
the Integrated Peripherals setup of the
Award BIOS.

2.7.4 Floppy Disk Drive Controller

1. Install the 34-pin header connector
into the shrouded floppy disk
header (J9) on the system board.
The colored edge of the ribbon
should be aligned with pin 1 of J9.

2. Install the other 34-pin header
connector(s) into the disk drive(s).
Align the colored edge of the daisy
chained ribbon cable with pin 1 of
the drive edge connector(s). The
end-most connector should be
attached to the drive you want to
designate as Drive A.

18

2.7.5 IDE Hard Disk Interface

1. If you are connecting two hard
drives, install the 40-pin connector
of the IDE cable into the primary
shrouded IDE header (connector
J11). If you are adding a third or
fourth IDE device, install the 40­pin connector of the other IDE
cable into the secondary shrouded
IDE header (connector J10).

2. Install the other 40-pin header
connector(s) into the device with
the colored edge of the ribbon
cable aligned with pin 1 of the drive edge connector(s).

Note:

Refer to your disk drive users manual for information about
selecting proper drive switch settings.

Adding a Second IDE Hard Drive

Hardware Installation

2

When using two IDE drives, one must be set as the master and the
other as the slave. Follow the instructions provided by the drive
manufacturer for setting the jumpers and/or switches on the drives.

We recommend that you use Enhanced IDE or ATA-2, ATA-3 and
Ultra DMA hard drives be from the same manufacturer. In a few
cases, drives from two different manufacturers will not function
properly when used together. The problem lies in the hard drives, not
the system board.

Important:

If you encountered problems while using an ATAPI CD-ROM
drive that is set in Master mode, please set the CD-ROM drive
to Slave mode. Some ATAPI CD-ROMs may not be recognized
and cannot be used if incorrectly set in Master mode.

19

2

Hardware Installation

2.7.6 Universal Serial Bus Ports

The system board is equipped with
two USB ports. USB allows data
exchange between your computer and
a wide range of simultaneously
accessible external Plug and Play
peripherals.

You must have the proper drivers
installed in your operating system to
use these ports. Refer to your
operating systems manual or
documentation.

2.7.7 IrDA Connector

The system board is equipped with an IrDA connector for wireless
connectivity between your computer and peripheral devices. Connect
your IrDA cable to connector J16 on the system board. Refer to
UART2 Mode Select in the Integrated Peripherals setup (Chapter

3). You must have the proper drivers installed in your operating
system to use this connector. Refer to your operating systems
manual or documentation.

20

Pin

1

2
3
4
5

Function

IRTX
GND
IRRX
N. C.
VCC

Hardware Installation

2.7.8 CPU Fan Connector

The processor must be kept cool by using a fan with heatsink.
Connect the CPU fan to the 3-pin fan connector at location J7 on
the system board.

2

Pin

1

2
3

Function

GND
+12V
Sense

2.7.9 Chassis Fan Connector

The system board is equipped with a chassis fan connector. If you
are installing a fan in the system unit, connect the fans connector to
location J3 on the system board. The fan will provide adequate
airflow throughout the chassis to prevent overheating the processor.

Pin

1
2

3

Function

GND
+12V
Sense

21

2

Hardware Installation

2.7.10 AGP Fan Connector

The system board is equipped with an AGP fan connector. If the
system board is installed with an AGP add-in card and you wish to
install a fan on the add-in card, connect the fans connector to
location J12 on the system board. Refer to the add-in cards manual
for instructions on installing the fan.

Pin

1
2

3

Function

GND
+12V
N.C.

2.7.11 J13 (LEDs and Switches)

22

Hardware Installation

2

SB-LED

(ATX power LED)

HD-LED

(Primary/Secondary IDE LED)

G-LED

(Green LED)

ATX-SW

(ATX power switch)

G-SW

(Green switch)

RESET

(Reset switch)

SPEAKER

(Speaker connector)

KEYLOCK

(Keylock Connector)

Pin

1
2

3
4

5
6
7

8
9

10
11

12
13

14
15
16

17
18

19
20
21
22

23
24

25
26
27
28

Pin Assignment

ATX Power
Ground

Open
HDD LED Power

HDD
Open
Green LED Power

Green
Open
PWRBT

Ground
Open
SMI

Ground
Open
H/W Reset

Ground
Open
Speaker Data

N. C.
Ground
Speaker Power

Open
LED Power

N.C.
Ground
Keylock
Ground

Use pins 24 to 26
for the Power LED.

23

2

Hardware Installation

SB-LED: ATX 5VSB Standby LED

This LED will light when the 5VSB power is active.

HD-LED: Primary/Secondary IDE LED

This LED will light when the hard drive is being accessed.

G-LED: Green LED

This LED will light when the system is in the Suspend mode.

ATX-SW: ATX Power Switch

Depending on the setting in the BIOS setup, this switch is a dual
function power button that will allow your system to enter the Soft­Off or Suspend mode. Refer to Soft-Off By PWRBTN in the Power
Management Setup (Chapter 3).

G-SW: Green Switch(For APM only)

Pressing this switch will allow your system to enter the Suspend
mode. Pressing it again or using the keyboard/mouse (that is, when
the Wake-On-Keyboard/Mouse function is enabled) will allow the
system to wake up completely from the Suspend mode.

RESET: Reset Switch

This switch allows you to reboot without having to power off the
system thus prolonging the life of the power supply or system.

SPEAKER: Speaker Connector

This connects to the speaker installed in the system chassis.

KEYLOCK: Keylock and Power LED Connector

This is used to connect to the keyboard lock (located on the front
panel of the system chassis) for locking the keyboard. Use pins 24
to 26 to connect to the Power LED.

24

Hardware Installation

2.7.12 SB-LINK Connector

If the system board is installed with a Creative sound card that
requires connecting the card to the SB-LINK connector, connect
the cable that came with the sound card to connector JP6. Refer
to the sound cards manual for more information.

2

Pin

1

2
3
4
5

6

Function

PC-PCI-GNTx
DGND
Key
PC-PCI-REQx
DGND
SERIRQ

25

2

Hardware Installation

2.7.13 Power Connector

The system board is equipped with an ATX power connector at
location J4 of the system board.

Pin

Function

1

3.3V/14A

2

3.3V/14A

3

Ground

4

+5V

5

Ground

6

+5V

7

Ground

8

PW-OK

9

5VSB

10

+12V

Important:

Your power supply must meet the ATX specification ­supporting 3.3V/14A (minimum), otherwise your system will not
boot properly.

Pin

11
12
13
14
15
16
17
18
19
20

Function

3.3V/14A

-12V
Ground
PS-ON
Ground
Ground
Ground

-5V
+5V
+5V

26

Hardware Installation

2.7.14 Wake-On-LAN (WOL) Connector

The system board supports the Wake-On-LAN function. This
function will allow the network to wake up a Soft Power Down
(Soft-Off) PC. However, if your system is in the Suspend mode, you
can wake-up the system only through an IRQ or DMA interrupt. To
use the Wake-On-LAN function, you must enable the Resume On
LAN field in the Power Management Setup of the Award BIOS.
Connect the cable that comes with your LAN card to location J14
on the system board. Refer to the add-in cards manual for details.
Note: Your LAN card must support Magic Packet in order to use
the Wake-On-LAN function.

2

Pin

1
2

3

Function

5VSB (720mA)
GND
Signal

Important:

The 5VSB power source of your power supply must support
720mA (minimum).

27

Chapter 3 - Award BIOS Setup Utility

3.1 The Basic Input/Output System

The Basic Input/Output System (BIOS) is a program that takes care
of the basic level of communication between the processor and
peripherals. In addition, the BIOS also contain codes for various
advanced features found in this system board. This chapter explains the
Setup Utility for the Award BIOS.

After you power up your system, the BIOS message appears on your
screen and the memory count begins. After the memory test, the
following message will appear on the screen:

Press DEL to enter setup

If the message disappears before you respond, restar t your system or
press the Reset button. You may also restart the system by pressing
the <Ctrl> <Alt> and <Del> keys simultaneously.

When you press <Del>, the main program screen will appear.

ROM PCI/ISA BIOS

CMOS SETUP UTILITY

AWARD SOFTWARE, INC.

STANDARD CMOS SETUP
BIOS FEATURES SETUP
CHIPSET FEATURES SETUP
POWER MANAGEMENT SETUP
PNP/PCI CONFIGURATION
LOAD FAIL-SAFE SETTINGS
LOAD OPTIMAL SETTINGS

Esc

: Quit

F10

: Save & Exit Setup

INTEGRATED PERIPHERALS
SUPERVISOR P ASSWORD
USER PASSWORD
IDE HDD AUTO DETECTION
SAVE & EXIT SETUP
EXIT WITHOUT SAVING

↑↓→←

: Select Item
: Change Color

(Shift) F2

3.1.1 Standard CMOS Setup

Use the arrow keys to highlight Standard CMOS Setup and press
<Enter>. A screen similar to the one on the next page will appear.

28

Award BIOS Setup Utility

ROM PCI/ISA BIOS
STANDARD CMOS SETUP
AWARD SOFTWARE, INC.

Date (mm:dd:yy) : Mon, Jul 29 1996
Time (hh:mm:ss) : 13: 27: 50

HARD DISKS
Primary Master
Primary Slave
Secondary Master
Secondary Slave

Drive A : 1.44M, 3.5 in.
Drive B : None

Video : EGA/VGA
Halt on : All Errors

: Quit

Esc
F10

: Save & Exit Setup

The settings on the screen are for reference only. Your version may not be
identical to this one.

Date

The date format is <day>, <month>, <date>, <year>. Day displays
a day, from Sunday to Saturday. Month displays the month, from
January to December. Date displays the date, from 1 to 31. Year
displays the year, from 1994 to 2079.

Time

:
:
:
:

TYPE
Auto
Auto
Auto
Auto

SIZE

0
0
0
0

CYLS

↑↓→←

HEAD
0
0
0
0

: Select Item
: Change(Shift)F2

0
0
0
0

PRECOMP

LANDZ
0
0
0
0

SECTOR

0

0

0

0

0

0

0

0

Base Memory : 640K
Extended Memory : 64512K
Other Memory : 384K

Total Memory : 65536K

PU/PD/+/- : Modify

MODE
Auto
Auto
Auto
Auto

3

The time format is <hour>, <minute>, <second>. The time is based
on the 24-hour military-time clock. For example, 1 p.m. is 13:00:00.
Hour displays hours from 00 to 23. Minute displays minutes from 00
to 59. Second displays seconds from 00 to 59.

Primary Master, Primary Slave, Secondary Master and Secondary Slave

These categories allow you to enter the appropriate specifications for
the type of hard disk drive(s) installed in your system. Press <PgUp>
or <PgDn> to select a numbered hard disk type or type the number
and press <Enter>. The hard disk will not work properly if you enter
improper information for this category. You can use Type User to
define your own drive type manually. This information should be included
in the documentation from your hard disk vendor. If you select Type
Auto, the BIOS will auto-detect the HDD & CD-ROM drive at the
POST stage and show the IDE for the HDD & CD-ROM drive. If a
hard disk has not been installed, select None and press <Enter>.

29

3

Award BIOS Setup Utility

Drive A and Drive B

These categories identify the types of floppy disk drives installed.
Choosing an incorrect type might cause your system to format the
floppy disk improperly and you cannot access your data. The options
for drive A and B are:

None No floppy drive is installed
360K, 5.25 in. 5-1/4 in. standard drive; 360KB capacity

1.2M, 5.25 in. 5-1/4 in. AT-type high-density drive; 1.2MB capacity
720K, 3.5 in. 3-1/2 in. double-sided drive; 720KB capacity

1.44M, 3.5 in. 3-1/2 in. double-sided drive; 1.44MB capacity

2.88M, 3.5 in. 3-1/2 in. double-sided drive; 2.88MB capacity

Video

This category selects the type of video adapter used for the primary
system monitor. Although secondary monitors are supported, you do
not have to select the type in Setup. The default setting is EGA/VGA
(BIOS default, Setup default).

EGA/VGA Enhanced Graphics Adapter/Video Graphics Array. For

EGA, VGA, SVGA and PGA monitor adapters.

CGA 40 Color Graphics Adapter. Power up in 40-column mode.
CGA 80 Color Graphics Adapter. Power up in 80-column mode.
Mono Monochrome adapter. Includes high resolution

monochrome adapters.

Halt On

This category determines whether the system will stop if an error is
detected during power up. The default setting is All, But Keyboard
(BIOS default, Setup default).

No Errors The system boot will not stop for any errors detected.
All Errors The system boot will stop whenever the BIOS detects

a non-fatal error.

All, But Keyboard The system boot will not stop for a keyboard

error; it will stop for all other errors.

All, But Diskette The system boot will not stop for a disk error;

it will stop for all other errors.

All, But Disk/Key The system boot will not stop for a disk or

keyboard error; it will stop for all other errors.

30

Award BIOS Setup Utility

Memory

The base memory size, extended memory size and the other memory
size cannot be altered; your computer automatically detects and displays
them.

Base Memory The POST will determine the amount of base (or

conventional) memory installed in the system. The
value of the base memory is typically 512K for
systems with 512K memory installed on the
motherboard or 640K for systems with 640K or
more memory installed on the motherboard.

Extended Memory The BIOS determines how much extended

memory is present during the POST. This is the
amount of memory located above 1MB in the
CPUs memory address map.

Other Memory This refers to the memory located in the 640K to

1024K address space. This is the memory that can
be used for different applications. DOS uses this
area to load device drivers in an effort to keep as
much base memory free for application programs.
The BIOS is the most frequent user of this RAM
area since this is where it shadows the ROM.

3

31

3

Award BIOS Setup Utility

3.1.2 BIOS Features Setup

The BIOS Features Setup allows you to configure your system for basic
operation. Some entries are defaults required by the system board,
while others, if enabled, will improve the performance of your system
or let you set some features according to your preference.

ROM PCI/ISA BIOS

BIOS FEATURES SETUP

AWARD SOFTWARE, INC.

Virus Warning
CPU L1 Cache
CPU L2 Cache
CPU L2 Cache ECC Checking
Quick Power On Self Test
Boot Sequence
Swap Floppy Drive
Boot Up Floppy Seek
Boot Up NumLock Status
Typematic Rate Setting
Typematic Rate (Chars/Sec)
Typematic Delay (Msec)
Security Option
PCI/VGA Palette Snoop
OS Select For DRAM > 64MB
HDD S.M.A.R.T. Capability

The settings on the screen are for reference only. Your version may not be
identical to this one.

: Disabled
: Enabled
: Enabled
: Enabled
: Enabled
: A, C, SCSI
: Disabled
: Disabled
:On
: Disabled
:6
: 250
: Setup
: Disabled
: Non-OS2
: Disabled

ESC

: Quit

F1

: Help

F5

: Old Values

F6

: Load Fail-Safe Settings

F7

: Load Optimal Settings

↑↓→←

PU/PD/+/­(Shift) F2

: Select Item
: Modify
: Color

Virus Warning

This category protects the boot sector and partition table of your hard
disk drive. When this item is enabled, the Award BIOS will monitor the
boot sector and partition table of the hard disk drive. If an attempt
is made to write to the boot sector or partition table of the hard disk
drive, the BIOS will halt the system and an error message will appear.

After seeing the error message, if necessary, you will be able to run
an anti-virus program to locate and remove the problem before any
damage is done.

Many disk diagnostic programs which attempt to access the boot
sector table will cause the warning message to appear. If you are
running such a program, we recommend that you first disable this
category. Also, disable this category if you are installing or running
certain operating systems like Windows® 95 or the operating system
may not install nor work.

32

Award BIOS Setup Utility

CPU L1 Cache and CPU L2 Cache

These categories speed up the memory access. The default value is
enabled. Enable the External Cache for better performance.

CPU L2 Cache ECC Checking

Intel Pentium II processor comes with built-in Level 2 cache. By default,
ECC is enabled to check the Level 2 cache. If you are not using this
function, set this field to Disabled.

Quick Power On Self Test

This category speeds up Power On Self Test (POST) after you power
on your system. When Enabled, the BIOS will shorten or skip some
check items during POST.

Boot Sequence

This category determines which drive to search first for the disk
operating system. The default is A, C, SCSI. The options are:

A, C, SCSI; C, A, SCSI; C, CDROM, A; CDROM, C, A;
D, A, SCSI; E, A, SCSI; F, A, SCSI; SCSI, A, C;
SCSI, C, A; C only; LS120/ZIP, C .

3

Swap Floppy Drive

When this option is enabled and the system is booting from the floppy
drive, the system will boot from drive B instead of drive A. When this
option is disabled and the system is booting from the floppy drive, the
system will boot from drive A. You must have two floppy drives to
use this function.

Boot Up Floppy Seek

When enabled, the BIOS will check whether the floppy disk drive installed
is 40 or 80 tracks. Note that the BIOS cannot distinguish between 720K,

1.2M, 1.44M and 2.88M drive types as they are all 80 tracks. When
disabled, the BIOS will not search for the type of floppy disk drive by
track number. Note that there will not be any warning message if the drive
installed is 360KB.

33

3

Award BIOS Setup Utility

Boot Up NumLock Status

This allows you to determine the default state of the numeric keypad.
By default, the system boots up with NumLock on wherein the function
of the numeric keypad is the number keys. When set to Off, the
function of the numeric keypad is the arrow keys.

Typematic Rate Setting

When disabled, continually holding down a key on your keyboard will
cause the BIOS to report that the key is down. When the typematic
rate is enabled, the BIOS will not only report that the key is down,
but will first wait for a moment, and, if the key is still down, it will begin
to report that the key has been depressed repeatedly. For example,
you would use such a feature to accelerate cursor movements with
the arrow keys.

Typematic Rate (Chars/Sec)

This selection allows you to select the rate at which the keys are
accelerated.

Typematic Delay (Msec)

This selection allows you to select the delay between when the key
was first depressed and when the acceleration begins.

Security Option

System The system will not boot and access to Setup will be

denied if the correct password is not entered at the
prompt.

Setup The system will boot, but access to Setup will be denied

if the correct password is not entered at the prompt.

PCI/VGA Palette Snoop

It determines whether the MPEG ISA/VESA VGA Cards can work with
PCI/VGA or not. The default value is Disabled.

Enabled PCI/VGA working with MPEG ISA/VESA VGA cards.
Disabled PCI/VGA not working with MPEG ISA/VESA VGA cards.

34

Award BIOS Setup Utility

OS Select for DRAM > 64MB

This item allows you to access the memory that is over 64MB in
OS/2. The options are: Non-OS/2 and OS/2.

HDD S.M.A.R.T. Capability

The system board supports SMART (Self-Monitoring, Analysis and
Reporting Technology) hard drives. SMART is a reliability prediction
technology for ATA/IDE and SCSI drives. The drive will provide sufficient
notice to the system or user to backup data prior to the drives failure.
The default is Disabled. If you are using hard drives that support
S.M.A.R.T., set this field to Enabled. SMART is supported in ATA-3 or
later hard drives.

3.1.3 Chipset Features Setup

ROM PCI/ISA BIOS

CHIPSET FEATURES SETUP

AWARD SOFTWARE, INC.

DIMM 1 DRAM Timing
DIMM 2 DRAM Timing
DIMM 3 DRAM Timing
SDRAM CAS Latency
Read Around Write
Concurrent PCI/Host
CPU to PCI Write Buffer
PCI Dynamic Bursting
PCI Master 0 WS Write
PCI Delay Transaction
PCI#2 Access #1 Retry
AGP Master 1 WS Write
AGP Master 1 WS Read
Video RAM Cacheable
Memory Hole At 15M-16M
AGP Aperture Size (MB)
AGP-2X Mode

: Normal
: Normal
: Normal
:3
: Disabled
: Disabled
: Enabled
: Enabled
: Enabled
: Enabled
: Disabled
: Enabled
: Disabled
: Disabled
: Disabled
:64
: Enabled

CPU Clock Frequency

**** System Health Monitor ****

Current CPU Temperature
Current CPU Fan Speed
Current Chassis Fan Speed
CPU Temperature Limit
CPU Fan Speed Limit
Chassis Fan Speed Limit
+3.3V Voltage
+12V Voltage
+5V Voltage
+1.5V Voltage

ESC

: Quit

F1

: Help

F5

: Old Values

F6

: Load Fail-Safe Settings

F7

: Load Optimal Settings

↑ ↓ → ←

PU/PD/+/-

(Shift) F2

: Default

:36
: 3750 RPM
: 0 RPM
: Ignore
: Ignore
: Ignore
: Ignore
: Ignore
: Ignore
: Ignore

o

C/96oF

: Select Item
: Modify
: Color

3

The settings on the screen are for reference only. Your version may not be
identical to this one.

This section gives you functions to configure the system based on
the specific features of the chipset. The chipset manages bus speeds
and access to system memory resources. It also coordinates
communications between the conventional ISA bus and the PCI bus.

These items should not be altered unless necessary. The default

settings have been chosen because they provide the best operating
conditions for your system. The only time you might consider making
any changes would be if you discovered some incompatibility or that
data was being lost while using your system.

35

3

Award BIOS Setup Utility

CPU Clock Frequency

The options in the CPU Clock Frequency field are: Default, 66MHz,
75MHz, 83MHz, 100MHz, 103MHz, 112MHz, 124MHz and 133MHz.
The default setting is Default. Under this setting, the system will run
at 66MHz or 100MHz depending on the processors clock frequency.

However, if you selected an option other than Default and is
unable to boot up the system, there are 2 methods of going back
to its default setting.

Method 1: Clear the CMOS data by following the procedure in
section 2.5 (chapter 2) of this manual. All fields in the BIOS Setup
will automatically be set to its default settings.

Method 2: Press the <Insert> key and Power button simultaneously
until the power-on screen appears. This will allow the system to boot
according to the FSB of the processor. Now press the <Del> key
to enter the Award BIOS setup utility. Select Chipset Features
Setup and set the CPU Clock Frequency field to Default or a
suitable clock frequency.

System Health Monitor

Note:

The system board comes with a System Health Monitor utility.
Once this utility is installed, the system will ignore the settings in
the System Health Monitor field of the Chipset Features Setup.

If you are using Windows 95 or Windows NT 4.0, you may
select between using the utility and the Chipset Features Setup.
For other operating systems, you may only use the Chipset
Features Setup. Refer to the System Health Monitor Utility
section (Chapter 4) for more information.

Current CPU Temperature, Current CPU Fan Speed and Current
Chassis Fan Speed

These fields show the current temperature of the processor, and the
current fan speed of the CPU and chassis fans in RPM (Revolutions
Per Minute).

36

Award BIOS Setup Utility

CPU Temperature Limit

This field allows you to manually set a limit to the processors
temperature. If the temperature of the processor is over the
temperature set in this field (70oC/158oF recommended), an alarm will
sound warning you of system overheat. The sound of the alarm is
continuous low to high beeps. Some of the most common causes
leading to high temperature are:

- The fan is not functioning normally or has stopped. Turn off your
system and replace the fan.

- The space clearance of the processor, fan and heat sink is
inadequate to maintain proper airflow and heat dissipation.

- The chassis or cabinet has poor ventilation.

CPU Fan Speed Limit and Chassis Fan Speed Limit

These fields allow you to manually set a limit to the speed of the CPU
and chassis fans. If the CPU/chassis fan speed is under the speed set
in these fields, an alarm will sound informing you to attend to any issue
that may damage your system. The sound of the alarm resembles that
of the siren of an ambulance. The failure detection circuit requires a
fan to operate at greater than 3600 RPM.

3

+1.5V, +3.3V, +5V and +12V Voltages

Set these fields to Monitor if you want the system board to detect
the output voltage of the power supply. If the output voltage is over
or under +1.5V/+3.3V/+5V/+12V (±10%), an alarm will sound
warning you of voltage issue. The sound of the alarm is continuous low
to high beeps but shorter than the temperature alarm. Some of the
most common causes leading to unstable output voltage of a power
supply are:

- The power supply is not functioning normally. Turn off your system
and replace the power supply.

- The AC input from the power outlet to your system is unstable.
Please consult your MIS department or an electrician.

37

3

Award BIOS Setup Utility

3.1.4 Power Management Setup

The Power Management Setup allows you to configure your system to
most effectively save energy. If you like to use the soft power down
feature of Windows 95, you must enable the Power Management
below. Select Min. Power, Max. Power or User Defined. Either one can
be used as long as it is NOT disabled.

ROM PCI/ISA BIOS

POWER MANAGEMENT SETUP

AWARD SOFTWARE, INC.

ACPI Function
Power Management
PM Control by APM
Video Off Method
Video Off After
Standby Mode
Suspend Mode
HDD Power Down
Soft-Off by PWRBTN
Resume on Ring
Resume on LAN
Resume on Alarm

The settings on the screen are for reference only. Your version may not be
identical to this one.

: Disabled
: User Define
:Yes
: DPMS
: Suspend
: Disabled
: Disabled
: Disabled
: Instant-Off
: Disabled
: Disabled
: Disabled

IRQ3 (COM 2)
IRQ4 (COM 1)
IRQ5 (LPT 2)
IRQ6 (Floppy Disk)
IRQ7 (LPT 1)
IRQ8 (RTC Alarm)
IRQ9 (IRQ2 Redir)
IRQ10 (Reserved)
IRQ11 (Reserved)
IRQ12 (PS/2 Mouse)
IRQ13 (Coprocessor)
IRQ14 (Hard Disk)
IRQ15 (Reserved)

ESC
F1
F5
F6
F7

** PM Events **

: Quit
: Help
: Old Values
: Load Fail-Safe Settings
: Load Optimal Settings

: Primary
: Primary
: Primary
: Primary
: Primary
: Disabled
: Secondary
: Secondary
: Secondary
: Secondary
: Primary
: Primary
: Disabled

↑ ↓ → ←

PU/PD/+/­(Shift) F2

: Select Item
: Modify
: Color

ACPI Function

By default, the ACPI function is disabled. This function should be
enabled only in operating systems that support ACPI such as
Windows 98 and Windows NT 5.0.

Power Management

This category allows you to select the type (or degree) of power saving
by changing the length of idle time that elapses before the Standby
mode and Suspend mode are activated.

Min Saving Minimum power management. Standby Mode = 1 hr.,

and Suspend Mode = 1 hr.

Max Saving Maximum power management. Standby Mode = 10

sec., and Suspend Mode = 10 sec.

User Define Allows you to set each mode individually. When

enabled, each option ranges from 10 sec. to 1 hr.

38

Award BIOS Setup Utility

PM Control by APM

Yes An Advanced Power Management device will be activated to

enhance the Max. Saving mode and stop the CPUs internal
clock. Use this option in Windows® 95. (default)

No The system BIOS will ignore APM when initiating the Power

Management mode.

Video Off Method

This determines the manner in which the monitor is blanked.

V/H SYNC + Blank This selection will cause the system to turn off

the vertical and horizontal synchronization
ports and write blanks to the video buffer.

Blank Screen This option only writes blanks to the video

buffer.

DPMS Initializes display power management signaling.

Use this option if your video board supports
it.

Video Off After

N/A The system BIOS will never turn off the screen.
Suspend The screen is off when the system is in the Suspend

mode.

Standby The screen is off when the system is in the Standby

mode.

3

Standby Mode

This is user configurable only when the Power Management category
is set to User Define. When enabled and after the set time of system
inactivity, the CPU clock will run at a slower speed while all other de­vices still operate at full speed.

Suspend Mode

This is user configurable only when the Power Management category
is set to User Define. When enabled and after the set time of system
inactivity, the CPU and onboard peripherals will be shut off.

39

3

Award BIOS Setup Utility

HDD Power Down

This is user configurable only when the Power Management category
is set to User Defined. When enabled and after the set time of system
inactivity, the hard disk drive will be powered down while all other
devices remain active.

Soft-Off by PWRBTN

This category allows you to select the method of powering off your
system.

Hold 4 Sec. Regardless of whether the Power Management field is

enabled or disabled, if the power button is pushed
and released in less than 4 sec, the system enters the
Suspend mode. The purpose of this function is to
prevent the system from powering off in case you
accidentally hit or pushed the power button. Pushing
the power button for more than 4 seconds will
power off the system.

Instant-Off Pressing and then releasing the power button at

once will immediately power off your system.

Resume on Ring

With an external modem installed, the Modem Ring-on function allows
your system to power-on to respond to incoming calls. To use this
function, set this field to Enabled.

Resume on LAN

With a LAN card installed, the Wake-On-LAN function allows the
network to wake up a Soft Power Down (Soft-Off) PC. However, if
your system is in the Suspend mode, you can wake-up the system only
through an IRQ or DMA interrupt. To use this function, set this field
to Enabled. Refer to the Wake-On LAN Connector section in
Chapter 2 of this manual for more information.

40

Award BIOS Setup Utility

Resume on Alarm

Enabled When Enabled, you can set the date and time you would

like the Soft Power Down (Soft-Off) PC to wake up.
However, if the system is being accessed by incoming calls
or the network (Resume on Ring/Resume on LAN) prior
to the date and time set in this field, the system will give
priority to the incoming calls or network. Date (of
Month) and Timer (hh:mm:ss) will appear right below
this field.

Disabled Disables the automatic wake up function. (default)

Date (of Month)

0 The system will power-on everyday according to the time

set in the Timer (hh:mm:ss) field.

1-31 Select a date you would like the system to power-on. The

system will power-on on the set date, and time set in the
Timer (hh:mm:ss) field.

Timer (hh:mm:ss)

This is used to set the time you would like the system to power-on.
If you want the system to power-on ever yday as set in the Date (of
Month) field, the time set in this field must be later than the time of
the RTC in the Standard CMOS Setup.

3

PM Events

When enabled, access to the specified IRQ will cause the system to
wake up completely from the power management mode. When
disabled, the system will not wake up from the power management
mode despite access to the specified IRQ.

41

3

Award BIOS Setup Utility

3.1.5 PNP/PCI Configuration

This section describes configuring the PCI bus system. It covers some
very technical items and it is strongly recommended that only
experienced users should make any changes to the default settings.

ROM PCI/ISA BIOS

PNP/PCI CONFIGURATION

AWARD SOFTWARE, INC.

Resources Controlled By
Reset Configuration Data

The settings on the screen are for reference only. Your version may not be
identical to this one.

Resources Controlled By

: Auto
: Disabled

Assign IRQ For VGA
PCI Slot 1 IRQ
PCI Slot 2 IRQ
PCI Slot 3 IRQ
PCI Slot 4 IRQ

ESC

: Quit

F1

: Help

F5

: Old Values

F6

: Load Fail-Safe Settings

F7

: Load Optimal Settings

: Enabled
: Auto
: Auto
: Auto
: Auto

↑ ↓ → ←

PU/PD/+/­(Shift) F2

: Select Item
: Modify
: Color

The Award Plug and Play BIOS has the capability to automatically
configure all of the boot and Plug and Play compatible devices.

Auto The system will automatically detect the settings for you.

The categories that follow will not be shown on the
screen.

Manual This will allow you to set the IRQ/DMA (you have

assigned your add-in card) to Legacy ISA or PCI/ISA PnP.
For non-PnP ISA cards, select Legacy ISA. For PnP ISA
or PCI cards, select PCI/ISA PnP.

42

Award BIOS Setup Utility

Reset Configuration Data

Enabled The BIOS will reset the configuration data once

automatically. It will then recreate a new set of
configuration data.

Disabled The BIOS will not reset the configuration data.

Assign IRQ for VGA

When Enabled, the system automatically assigns an IRQ for the VGA
card installed. Your VGA card will need an IRQ only when using the
video capture function of the card. If you are not using this function
and a new device requires an IRQ, you can set this function to
Disabled. The IRQ (previously occupied by the VGA card) will be
available for your new device.

Note:

When Disabled, a Yellow mark will appear in Windows 95s
Device Manager.

PCI Slot 1 IRQ to PCI Slot 4 IRQ

By default, an IRQ is automatically assigned to each PCI slot. You may
also specify an IRQ to these slots. The options are: 3, 4, 5, 7, 9, 10,
11, 12, 14 and 15.

3

3.1.6 Load Fail-Safe Settings

The Load Fail-Safe Settings option loads the troubleshooting default
values permanently stored in the ROM chips. These settings are not
optimal and turn off all high performance features. You should use these
values only if you have hardware problems. Highlight this option on the
main menu and press <Enter>. The message below will appear.

Load Fail-Safe Settings (Y/N)? N

If you want to proceed, type <Y> and press <Enter>. The default
settings will be loaded.

43

3

Award BIOS Setup Utility

3.1.7 Load Optimal Settings

The Load Optimal Settings option loads optimized settings from the
BIOS ROM. Use the Setup default values as standard values for your
system. Highlight this option on the main menu and press <Enter>. The
message below will appear.

Load Optimal Settings (Y/N)? N

Type <Y> and press <Enter> to load the Setup default values.

3.1.8 Integrated Peripherals

ROM PCI/ISA BIOS

INTEGRATED PERIPHERALS

AWARD SOFTWARE, INC.

Onboard Primary PCI IDE
Onboard Secondary PCI IDE
IDE Prefetch Mode
IDE HDD Block Mode
IDE Primary Master PIO
IDE Primary Slave PIO
IDE Secondary Master PIO
IDE Secondary Slave PIO
IDE Primary Master UDMA
IDE Primary Slave UDMA
IDE Secondary Master UDMA
IDE Secondary Slave UDMA
Init Display First
USB Controller

: Enabled
: Enabled
: Enabled
: Enabled
: Auto
: Auto
: Auto
: Auto
: Auto
: Auto
: Auto
: Auto
: AGP
: Disabled

KBC Input Clock
Onboard FDC Controller
Onboard Serial Port 1
Onboard Serial Port 2
UART2 Mode Select

Onboard Parallel Port
Parallel Port Mode
ECP Mode Use DMA
EPP Mode Select
Keyboard/Mouse Power On

ESC

: Quit

F1

: Help

F5

: Old Values

F6

: Load Fail-Safe Settings

F7

: Load Optimal Settings

↑ ↓ → ←

PU/PD/+/­(Shift) F2

: 8MHz
: Enabled
: 3F8/IRQ4
: 2F8/IRQ3
: Normal

: 378/IRQ7
: ECP+EPP
:3
: EPP1.7
: Disabled

: Select Item
: Modify
: Color

The settings on the screen are for reference only. Your version may not be
identical to this one.

Onboard Primary PCI IDE and Onboard Secondary PCI IDE

These categories allow you to enable or disable the primary and
secondary IDE controller. The default is Enabled. Select Disabled if you
want to add a different hard drive controller.

44

Award BIOS Setup Utility

IDE Prefetch Mode

The onboard IDE drive interfaces supports IDE prefetching, for faster
drive accesses. If you install a primar y and/or secondary add-in IDE
interface, set this field to Disabled if the interface does not support
prefetching.

IDE HDD Block Mode

Enabled The IDE HDD uses the block mode. The system BIOS

will check the hard disk drive for the maximum block size
the system can transfer. The block size will depend on the
type of hard disk drive.

Disabled The IDE HDD uses the standard mode.

IDE Primary Master/Slave PIO and IDE Secondary Master/Slave PIO

PIO means Programmed Input/Output. Rather than have the BIOS
issue a series of commands to effect a transfer to or from the disk
drive, PIO allows the BIOS to tell the controller what it wants and
then let the controller and the CPU perform the complete task by
themselves. Your system supports five modes, 0 (default) to 4, which
primarily differ in timing. When Auto is selected, the BIOS will select the
best available mode after checking your drive.

3

Auto The BIOS will automatically set the system according to your

hard disk drives timing.

0-4 You can select a mode that matches your hard disk drives

timing. Caution: Do not use the wrong setting or you will
have drive errors.

IDE Primary Master/Slave UDMA and IDE Secondary Master/Slave
UDMA

These categories allow you to set the Ultra DMA in use. When Auto
is selected, the BIOS will select the best available option after checking
your hard drive or CD-ROM.

Auto The BIOS will automatically detect the settings for you.
Disabled The BIOS will not detect these categories.

45

3

Award BIOS Setup Utility

Init Display First

This field applies only to systems installed with both PCI and AGP
cards. It allows you to select which one to initialize first when the
system boots.

AGP When the system boots, it will first initialize AGP.
PCI Slot When the system boots, it will first initialize PCI.

USB Controller

Select Enabled if your system contains a Universal Serial Bus (USB)
controller and you have USB peripherals.

USB Keyboard Support

By default, USB Keyboard Suppor t is Disabled. If you are operating
under DOS, make sure to enable this function.

KBC Input Clock

This is used to select the input clock of your keyboard. The options
are: 6MHz, 8MHz, 12MHz and 16MHz. The default is 8MHz.

Onboard Serial Port 1 and Onboard Serial Port 2

Auto The system will automatically select an I/O address for the

onboard serial port 1 and serial port 2.

3F8/IRQ4, 2F8/IRQ3, 3E8/IRQ4, 2E8/IRQ3 Allows you to manually

select an I/O address for the onboard serial port 1 and
serial port 2.

Disabled Disables the onboard serial port 1 and/or serial por t 2.

UART2 Mode Select

The system board supports IrDA function for wireless connectivity
between your computer and peripheral devices. You may not use IrDA
(J16) and the COM 2 serial port (J8) at the same time. If you are
using the COM 2 serial port, make sure UART2 Mode Select is set
to Normal.

46

Award BIOS Setup Utility

To use the IrDA function, follow the steps below.

1. Connect your IrDA cable to connector J16 on the system
board.

2. Set UART2 Mode Select to the type of IrDA standard
supported by your IrDA peripheral/device (IrDA or ASKIR).

3. The following will appear right after UART2 Mode Select.

IR Transmission Delay

If this option is Enabled, transmission of data will be slower. This is
recommended when you encounter transmission problem with your
device. The options are: Enabled and Disabled.

Onboard Parallel Port

378H/IRQ7, 3BCH/IRQ7, 278H/IRQ5 Selects the I/O address and

IRQ for the onboard parallel port.

Disabled Disables the onboard parallel port.

Parallel Port Mode

Parallel Port Mode will appear only if you selected an I/O address and
IRQ in the Onboard Parallel Por t field. This option applies to a
standard specification and will depend on the type and speed of your
device. Refer to your peripherals manual for the best option. Select the
parallel port mode according to the type of printer device connected
to your onboard parallel port.

3

The parallel modes are SPP, EPP, ECP and ECP+EPP. The default is
ECP+EPP. Both ECP Mode Use DMA and EPP Mode Select will
appear on the screen. If you selected EPP, EPP Mode Select will
appear. This field applies to standard specification. The options are
EPP1.9 and EPP1.7. Default setting: EPP1.7. If you selected ECP, ECP
Mode Use DMA will appear. This is used to select a DMA channel
for the parallel port. The options are 1 and 3. Default setting: 3.

47

3

Award BIOS Setup Utility

Keyboard/Mouse Power On

This field allows you to use the keyboard or mouse to power-on the
system. To use this function, make sure JP7 is set to 2-3 On - the
Wake-On-Keyboard/Mouse function enabled. Refer to Jumper Settings
for Wake-On-Keyboard/Wake-On-Mouse in Chapter 2 of this manual
for more information.

Disabled Default setting.

Warning:

If JP7 was previously enabled with a password
set in this field, and now you wish to disable the
password function, make sure to set this field
to Disabled prior to setting JP7 to 1-2 On ­Disabled, otherwise you will not be able to boot
up the system.

Password When this option is selected, the KB Power On

Password field will appear. Move the cursor to this
field and press <Enter>. Enter your password. You can
enter up to 5 characters. Type in exactly the same
password to confirm, then press <Enter>.

Important:

The power button will not function once a
keyboard password has been set in the KB
Power On Password field. You must type the
password to power-on the system.

Hot Key When this option is selected, the KB Power On Hot

Key field will appear. Move the cursor to this field to
select a function key you would like to use to power­on the system. The options are Ctrl-F1 to Ctrl-F12.

Mouse Left When this option is selected, double-click the left but-

ton of the mouse to power-on the system.

Mouse Right When this option is selected, double-click the right

button of the mouse to power-on the system.

Any Key You can press any key to power-on the system.

48

Award BIOS Setup Utility

3.1.9 Supervisor Password

If you want to protect your system and setup from unauthorized entry,
set a supervisors password with the System option selected in the
BIOS Features Setup. If you want to protect access to setup only, but
not your system, set a supervisors password with the Setup option
selected in the BIOS Features Setup. You will not be prompted for a
password when you cold boot the system.

Use the arrow keys to highlight the Supervisor Password option and
press <Enter>. The message below will appear.

Enter Password:

Type in the password. You are limited to eight characters. When done,
the message below will appear:

Confirm Password:

You are asked to verify the password. Type in exactly the same
password. If you type in a wrong password, you will be prompted to
enter the correct password again. To delete or disable the password
function, highlight Supervisor Password and press <Enter>, instead of
typing in a new password. Press the <Esc> key to return to the main
menu.

3

3.1.10 User Password

If you want another user to have access only to your system but not
to setup, set a users password with the System option selected in
the BIOS Features Setup. If you want a user to enter a password when
trying to access setup, set a users password with the Setup option
selected in the BIOS Features Setup. Using users password to enter
Setup allows a user to access only the User Password option that
appears on the main screen. Access to all other options is denied. To
set, confirm, verify, disable or delete a users password, follow the
procedures described in the section Supervisor Password. If you
forget your password, refer to the procedure described in the same
section.

49

3

Award BIOS Setup Utility

3.1.11 IDE HDD Auto Detection

Use this option to detect the parameters for the hard disk drives
installed in your system. These parameters will then be automatically
entered into the "Standard CMOS Setup". The IDE HDD Auto
Detection screen displays the following categories of information: Size,
Cylinders, Heads, Precomp, LandZone, Sectors and Mode.

ROM PCI/ISA BIOS

CMOS SETUP UTILITY

AWARD SOFTWARE, INC.

HARD DISKS TYPE SIZE CYLS HEAD RECOMP LANDZ SECTOR MODE

Primary Master:

Select Primary Master Option (N=Skip): N
OPTIONS SIZE CYLS HEAD RECOMP LANDZ SECTOR MODE
2 (Y) 853 827 32 0 1653 63 LBA

1 853 1654 16 65535 1653 63 Normal
3 853 827 32 65536 1653 63 Large

Note: Some OS (like SCO-UNIX) must be “NORMAL” for installation

ESC: Skip

The settings on the screen are for reference only. Your version may not be
identical to this one.

For hard drives larger than 528MB, you would typically select the LBA
type. Certain operating systems require that you select Normal or
Large. Please check your operating systems manual or Help desk on
which one to select.

50

Award BIOS Setup Utility

3.1.12 Save & Exit Setup

When all the changes have been made, highlight Save & Exit Setup
and press <Enter>. The message below will appear:

Save to CMOS and Exit (Y/N)? N

Type Y and press <Enter>. The modifications you have made will be
written into the CMOS memory, and the system will reboot. You will
once again see the initial diagnostics on the screen. If you wish to make
additional changes to the setup, press <Ctrl> <Alt> <Esc>
simultaneously or <Del> after memory testing is done.

3.1.13 Exit Without Saving

When you do not want to save the changes you have made, highlight
Exit Without Saving and press <Enter>. The message below will
appear:

Quit Without Saving (Y/N)? N

Type Y and press <Enter>. The system will reboot and you will once
again see the initial diagnostics on the screen. If you wish to make any
changes to the setup, press <Ctrl> <Alt> <Esc> simultaneously or
<Del> after memory testing is done.

3

51

Chapter 4 - Supported Softwares

4.1 Desktop Management Interface (DMI)

The system board comes with a DMI built into the BIOS. DMI, along
with the appropriately networked software, is designed to make
inventory, maintenance and troubleshooting of computer systems easier.
With DMI, a network administrator or MIS engineer can remotely
access some information about a particular computer system without
physically going to it. Quite often a service call may be unnecessary as
the problem can be solved remotely.

The DMI utility in the BIOS automatically records various information
about your system configuration. Information about the type and speed
of CPU, type and amount of memory for each memory slot, BIOS
revision level, types of add-in PCI boards and components, certain
revision numbers of hardware installed, etc. are automatically detected
and stored in the DMI pool, which is a par t of the system board's
Plug and Play BIOS. Additional information, such as ISA based
peripherals, which may not be automatically detected, can be manually
recorded in the DMI pool by using the Add DMI menu. The DMI pool
data is then verified or updated whenever the system hardware or
setup is altered.

4.1.1 Running the DMI Utility

To run the DMI utility, type: DMICFG.EXE. Please contact your sales
representative for the utility.

The DMI utility must run in real mode with at least 180K of base
memory. Memory managers like HIMEM.SYS (required by Windows)
must not be installed. You may do this by using one of the 3 methods
listed below.

1. Boot up from a system diskette without the AUTOEXEC.BAT and
CONFIG.SYS files,

2. REM HIMEM.SYS in the CONFIG.SYS, or

3. Press <F5> during bootup to bypass your AUTOEXEC.BAT and
CONFIG.SYS files.

52

4.1.2 Using the DMI Utility

Supported Softwares

4

[Edit DMI] [Add DMI] [Load DMI File] [Save DMI File]

▲▲

▲

▲▲

■■

■

■■

▲▲

▲

▲▲

↑ ↓ ↑ ↓

↑ ↓

↑ ↓ ↑ ↓
→→

→

→→

Award DMI Configuration Utility Copyright Award Software Inc, 1996

BIOS

System

Enclosure/Chassis

Processor

Memory Controller

Memory Module
Memory Module
Memory Module
Memory Module

Cache

Cache
Port Connector
Port Connector
Port Connector
Port Connector
Port Connector
Port Connector
Port Connector

System Slots

←←

←

←←

Move cursor ENTER-Accept DEL-Delete ESC-Abort&Exit

Type : BIOS Information
Handle : 0000

Vendor Name :
BIOS Version :
BIOS Starting Address Segment : F000
BIOS Build Date :
BIOS Characteristics :
Size of BIOS ROM : 0128K

*** BIOS Auto Detect ***

The four menus located on top of the DMI Configuration Utility screen
are Edit DMI, Add DMI, Load DMI File and Save DMI File. Use the
← or → (left or right) arrow keys to select a menu from the Menu
bar.

On the left side of the screen is a list of the system configuration items.
Use the ↑ or ↓ (up or down) arrow keys to select an item.

The commands at the bottom of the screen will allow you to navigate
through the various setup menus.

Edit DMI

1. Use the ← or → arrow keys to select the Edit DMI menu.

2. Highlight the item on the left screen that you would like to edit

by using the ↑ or ↓ arrow keys, then press <Enter>.

3. The cursor will move to the screen you select allowing you to edit
information. The screen will also display the auto-detected
information.

4. Press <F10> to update the edited information into the flash ROM.

53

4

Supported Softwares

Add DMI

1. Use the ← or → arrow keys to select the Add DMI menu.

2. Highlight the item on the left screen that you would like to add

by using the ↑ or ↓ arrow keys, then press <Enter>.

3. The cursor will move to the screen you select allowing you to enter
information about the added item.

4. Press <F10> to save information into the flash ROM.

To view information about the added items, go to the Edit DMI menu.

Load DMI File

1. Use the ← or → arrow keys to select the Load DMI File menu.

2. The following message will appear.

Press [Enter] to select DMI file for load

Press <Enter>.

3. The DMI files will appear on the screen. Select the file you would
like to load and press <Enter>.

4. The following message will appear.

Do you want to execute? (Y/N)

Type <Y>. All previous DMI structures will be destroyed and the
new file will be saved into the flash ROM.

Save DMI File

1. Use the ← or → arrow keys to select the Save DMI File menu.

2. The following message will appear.

Press [Enter] to select DMI file for save

Press <Enter>.

3. Enter the directory and filename under which you would like the
DMI file saved.

54

Supported Softwares

4.2 System Health Monitor Utility

The system board comes with a System Health Monitor utility
contained in the provided CD. This utility shows the current
temperature of the processor, power voltages, and processor/
chassis fan speed.

The utility also allows you to manually set the range of the
processors temperature, power voltages, and processor/chassis fan
speed. If the settings/values are over or under the set range, an
error message will pop-up and an alarm will sound. There are
three types of sound for the three different failure alarms
(temperature, voltage and fan). Refer to the Chipset Features
Setup (Chapter 3) section for details.

When you hear a failure alarm, you must power off your
computer and check the following: processor fan/heatsink, chassis
fan and power supply. We recommend that you use the Default
Setting which is the ideal setting that would keep the system in
good working condition.

Genesys Logic System Health Monitor Rev. A

The time
interval for
monitoring

the system

CPU

temperature

limit

Current

temperature

of the CPU

Output

voltage

limit

CPU/

Chassis

fan speed

limit

Polling Interval:
T emperature

CPU Over-Heat Temperature:
CPU Hysterisis Temperature: 70
CPU T emperature: 29

Voltage (V)

Fan (RPM)

CPU Fan
Chassis Fan

4 Seconds

75

High Limit Low LimitCurrent Voltage

3.3V

3.63

13.20

12.0V

5.0V

5.50

1.5V 1.65 1.54 1.35

Low Limit

2000
1000

3.29

11.98

5.00

6

Celsius
Fahrenheit

2.97

10.80

4.50

Current Speed:

4285
3478

Update w/o Save
Update and Save

User Setting

Default Setting

Quit

o

Minimize when Startup

Alarm when

CPU Over Heat

þ

3.3V Abnormal

þ

12V Abnormal

þ

5V Abnormal

þ

1.5V Abnormalþ
CPU Fan Abnormal

þ

Chassis Fan Abnormal

o

When
enabled,
this screen
will minimize
and display a
histogram
icon after
boot-up

These
items when
enabled will
alert you in
case of
detected
failure

4

55

4

Supported Softwares

Important:

Once this utility is installed, the system will ignore the settings in
the System Health Monitor field of the Chipset Features Setup.
If you are using Windows 95 or Windows NT 4.0, you may
select between using the utility and the Chipset Features Setup.
For other operating systems, you may only use the Chipset
Features Setup.

4.2.1 Installing the Utility

Insert the CD that came with the system board into a CD-ROM
drive. Run SETUP.EXE of the System Health Monitor utility. After
completing installation, you will find this utility in StartUp under
Programs of Windows 95/NT4.0. Please refer to the Readme
file for details on using the utility.

4.3 Drivers

The system board package comes with drivers for different
operating systems contained in the provided CD. To install the
drivers, please refer to the Readme file contained in the
provided CD.

If you are running Windows 95 (Win95, Win95+, Win95 OSR1:
Windows 95 OEM Service Release 1, Win95 OSR2: Windows 95
OEM Service Release 2.0 or Win95 OSR2.1: Windows 95 OEM
Service Release 2.0 plus USB Supplement), you need to run a
utility. Please refer to the Readme file contained in the provided
CD.

All steps or procedures to install software drivers are subject to
change without notice as the softwares are occassionally updated.
Please refer to the readme files for the latest information.

56

Appendix A - System Error Message

When the BIOS encounters an error that requires the user to
correct something, either a beep code will sound or a message will
be displayed in a box in the middle of the screen and the message,
PRESS F1 TO CONTINUE, CTRL-ALT-ESC or DEL TO ENTER
SETUP, will be shown in the information box at the bottom. Enter
Setup to correct the error.

A.1 POST Beep

There are two kinds of beep codes in the BIOS. One code
indicates that a video error has occured and the BIOS cannot
initialize the video screen to display any additional information. This
beep code consists of a single long beep followed by three short
beeps. The other code indicates that a DRAM error has occured.
This beep code consists of a single long beep.

A.2 Error Messages

One or more of the following messages may be displayed if the
BIOS detects an error during the POST. This list indicates the error
messages for all Awards BIOSes:

CMOS BATTERY HAS FAILED

The CMOS battery is no longer functional. It should be replaced.

Caution:

Danger of explosion if battery incorrectly replaced. Replace only
with the same or equivalent type recommended by the
manufacturer. Dispose of used batteries according to the
battery manufacturers instructions.

CMOS CHECKSUM ERROR

Checksum of CMOS is incorrect. This can indicate that CMOS has
become corrupt. This error may have been caused by a weak
battery. Check the battery and replace if necessary.

DISPLAY SWITCH IS SET INCORRECTLY

The display switch on the motherboard can be set to either
monochrome or color. This indicates the switch is set to a different

57

A

System Error Message

setting than indicated in Setup. Determine which setting is correct,
either turn off the system and change the jumper or enter Setup
and change the VIDEO selection.

FLOPPY DISK(S) fail (80)

Unable to reset floppy subsystem.

FLOPPY DISK(S) fail (40)

Floppy type mismatch.

Hard Disk(s) fail (80)

HDD reset failed.

Hard Disk(s) fail (40)

HDD controller diagnostics failed.

Hard Disk(s) fail (20)

HDD initialization error.

Hard Disk(s) fail (10)

Unable to recalibrate fixed disk.

Hard Disk(s) fail (08)

Sector Verify failed.

Keyboard is locked out - Unlock the key

The BIOS detects that the keyboard is locked. Keyboard controller is
pulled low.

Keyboard error or no keyboard present

Cannot initialize the keyboard. Make sure the keyboard is attached
correctly and no keys are being pressed during the boot.

Manufacturing POST loop

System will repeat POST procedure infinitely while the keyboard
controller is pull low. This is also used for the M/B burn in test at the
factory.

BIOS ROM checksum error - System halted

The checksum of ROM address F0000H-FFFFFH is bad.

Memory test fail

The BIOS reports memory test fail if the memory has error(s).

58

Appendix B - Troubleshooting

B.1 Troubleshooting Checklist

This chapter of the manual is designed to help you with problems
that you may encounter with your personal computer. To efficiently
troubleshoot your system, treat each problem individually. This is to
ensure an accurate diagnosis of the problem in case a problem has
multiple causes.

Some of the most common things to check when you encounter
problems while using your system are listed below.

1. The power switch of each peripheral device is turned on.

2. All cables and power cords are tightly connected.

3. The electrical outlet to which your peripheral devices are
connected is working. Test the outlet by plugging in a lamp or
other electrical device.

4. The monitor is turned on.

5. The displays brightness and contrast controls are adjusted
properly.

6. All add-in boards in the expansion slots are seated securely.

7. Any add-in board you have installed is designed for your system
and is set up correctly.

Monitor/Display

If the display screen remains dark after the system is turned on:

1. Make sure that the monitors power switch is on.

2. Check that one end of the monitors power cord is properly
attached to the monitor and the other end is plugged into a
working AC outlet. If necessary, try another outlet.

3. Check that the video input cable is properly attached to the
monitor and the systems display adapter.

4. Adjust the brightness of the display by turning the monitors
brightness control knob.

59

B

Troubleshooting

The picture seems to be constantly moving.

1. The monitor has lost its vertical sync. Adjust the monitors vertical
sync.

2. Move away any objects, such as another monitor or fan, that
may be creating a magnetic field around the display.

3. Make sure your video cards output frequencies are supported
by this monitor.

The screen seems to be constantly wavering.

1. If the monitor is close to another monitor, the adjacent monitor
may need to be turned off. Fluorescent lights adjacent to the
monitor may also cause screen wavering.

Power Supply

When the computer is turned on, nothing happens.

1. Check that one end of the AC power cord is plugged into a live
outlet and the other end properly plugged into the back of the
system.

2. Make sure that the voltage selection switch on the back panel is
set for the correct type of voltage you are using.

3. The power cord may have a shor t or open. Inspect the cord
and install a new one if necessary.

Floppy Drive

The computer cannot access the floppy drive.

1. The floppy diskette may not be formatted. Format the diskette
and try again.

2. The diskette may be write-protected. Use a diskette that is not
write-protected.

3. You may be writing to the wrong drive. Check the path
statement to make sure you are writing to the targeted drive.

4. There is not enough space left on the diskette. Use another
diskette with adequate storage space.

60

Troubleshooting

Hard Drive

Hard disk failure.

1. Make sure the correct drive type for the hard disk drive has
been entered in the BIOS.

2. If the system is configured with two hard drives, make sure the
bootable (first) hard drive is configured as Master and the
second hard drive is configured as Slave. The master hard drive
must have an active/bootable partition.

Excessively long formatting period.

1. If your hard drive takes an excessively long period of time to
format, it is likely a cable connection problem. However, if your
hard drive has a large capacity, it will take a longer time to
format.

Parallel Port

The parallel printer doesnt respond when you try to print.

1. Make sure that your printer is turned on and that the printer is
on-line.

2. Make sure your software is configured for the right type of
printer attached.

3. Verify that the onboard LPT ports I/O address and IRQ settings
are configured correctly.

4. Verify that the attached device works by attaching it to a parallel
port that is working and configured correctly. If it works, the
printer can be assumed to be in good condition. If the printer
remains inoperative, replace the printer cable and try again.

B

61

B

Troubleshooting

Serial Port

The serial device (modem, printer) doesnt output anything or is
outputting garbled characters.

1. Make sure that the serial devices power is turned on and that
the device is on-line.

2. Verify that the device is plugged into the correct serial port on
the rear of the computer.

3. Verify that the attached serial device works by attaching it to a
serial port that is working and configured correctly. If the serial
device does not work, either the cable or the serial device has a
problem. If the serial device works, the problem may be due to
the onboard I/O or the address setting.

4. Make sure the COM settings and I/O address are configured
correctly.

Keyboard

Nothing happens when a key on the keyboard was pressed.

1. Make sure the keyboard is properly connected.

2. Make sure there are no objects resting on the keyboard and
that no keys are pressed during the booting process.

System Board

1. Make sure the add-in card is seated securely in the expansion
slot. If the add-in card is loose, power off the system, re-install
the card and power up the system.

2. Check the jumper settings to ensure that the jumpers are
properly set.

3. Verify that all memory modules are seated securely into the
memory sockets.

4. Make sure the SIMMs are in the correct locations.

5. If the board fails to function, place the board on a flat surface
and seat all socketed components. Gently press each component
into the socket.

6. If you made changes to the BIOS settings, re-enter setup and
load the BIOS defaults.

62