DFI Infinity NF-ULTRA-M2, Infinity NF-M2 User Manual

System Board User’s Manual

935-NF4UM1-000G

92510626

This publication contains information that is protected by copyright. No part of it may be reproduced in any form or by any means or used to make any transformation/adaptation without the prior written permission from the copyright holders.

This publication is provided for informational purposes only. The manufacturer makes no representations or warranties with respect to the contents or use of this manual and specifically disclaims any express or implied warranties of merchantability or fitness for any particular purpose. The user will assume the entire risk of the use or the results of the use of this document. Further, the manufacturer reserves the right to revise this publication and make changes to its contents at any time, without obligation to notify any person or entity of such revisions or changes.

Trademarks

Product names or trademarks appearing in this manual are for identification purpose only and are the properties of the respective owners.

FCC and DOC Statement on Class B

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio TV technician for help.

Notice:

1. The changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

2. Shielded interface cables must be used in order to comply with the emission limits.

Table of Contents

About this Manual................................................................................

Warranty.................................................................................................

Registering the Product.......................................................................

Static Electricity Precaution................................................................

Safety Measures.....................................................................................

About the Package...............................................................................

Before Using the System Board.........................................................

Chapter 1 - Introduction....................................................................

Specifications...................................................................................................................................

Features..............................................................................................................................................

Français................................................................................................................................................

Deutsch...............................................................................................................................................

Español................................................................................................................................................

Русский язык.........................................................................................................................

Japanese.............................................................................................................................................

Chapter 2 - Hardware Installation....................................................

System Board Layout ..........................................................................................................

System Memory..........................................................................................................................

CPU.......................................................................................................................................................

Jumper Settings............................................................................................................................

Rear Panel I/O Ports.............................................................................................................

Internal I/O Connectors.....................................................................................................

Chapter 3 - BIOS Setup......................................................................

Award BIOS Setup Utility.................................................................................................

NVRAID BIOS..........................................................................................................................

Updating the BIOS..................................................................................................................

Chapter 4 - Supported Softwares.....................................................

Chapter 5 - Cool’n’Quiet Technology..............................................

Chapter 6 - RAID.................................................................................

Appendix A - System Error Message...............................................

Appendix B - Troubleshooting..........................................................

5 5 6 8 8 9 9

10 10 12 17 19 21 23 25

27 27 29 33 39 44 55

70 114 115

117 130 133 138 140

About this Manual

An electronic file of this manual is included in the CD. To view the user’s manual, insert the CD into a CD-ROM drive. The autorun screen (Mainboard Utility CD) will appear. Click the “TOOLS” icon then click “Manual” on the main menu.

Warranty

1. Warranty does not cover damages or failures that arised from misuse of the product, inability to use the product, unauthorized replacement or alteration of components and product specifications.

2. The warranty is void if the product has been subjected to physical abuse, improper installation, modification, accidents or unauthorized repair of the product.

3. Unless otherwise instructed in this user’s manual, the user may not, under any circumstances, attempt to perform service, adjustments or repairs on the product, whether in or out of warranty. It must be returned to the purchase point, factory or authorized service agency for all such work.

4. We will not be liable for any indirect, special, incidental or consequencial damages to the product that has been modified or altered.

Introduction

Registering the Product

We encourage you to register your DFI product online. DFI’s product registration service entitles you to notifications about product updates, special discounts and/or promotional offers; and puts your licensing information on file so that we may efficiently assist you if in any case needed. Please follow the steps below to access the product registration page.

1. Run Internet Explorer then type www.dfi.com.tw in the Address bar. On DFI’s homepage, click Global or the language of your choice.

2. Click the Support menu then select Product Register Service.

Introduction

3. The DFI Product Registration page will appear. Click Next to continue.

4. Select or fill in the necessary information to complete the registration.

5. Thank you for registering your DFI product.

Introduction

Static Electricity Precautions

It is quite easy to inadvertently damage your PC, system board, components or devices even before installing them in your system unit. Static electrical discharge can damage computer components without causing any signs of physical damage. You must take extra care in handling them to ensure against electrostatic build-up.

1. To prevent electrostatic build-up, leave the system board in its anti-static bag until you are ready to install it.

2. Wear an antistatic wrist strap.

3. Do all preparation work on a static-free surface.

4. Hold the device only by its edges. Be careful not to touch any of the components, contacts or connections.

5. Avoid touching the pins or contacts on all modules and connectors. Hold modules or connectors by their ends.

Important:

Electrostatic discharge (ESD) can damage your processor, disk drive and other components. Perform the upgrade instruction procedures described at an ESD workstation only. If such a station is not available, you can provide some ESD protection by wearing an antistatic wrist strap and attaching it to a metal part of the system chassis. If a wrist strap is unavailable, establish and maintain contact with the system chassis throughout any procedures requiring ESD protection.

Safety Measures

To avoid damage to the system:

• Use the correct AC input voltage range

To reduce the risk of electric shock:

• Unplug the power cord before removing the system chassis cover for installation or servicing. After installation or servicing, cover the system chassis before plugging the power cord.

Battery:

• Danger of explosion if battery incorrectly replaced.

• Replace only with the same or equivalent type recommend

the manufacturer.

• Dispose of used batteries according to the battery manufacturer’s

instructions.

Introduction

About the Package

The system board package contains the following items. If any of these items are missing or damaged, please contact your dealer or sales representative for assistance.

; One system board ; One IDE cable ; One floppy cable ; Two Serial ATA data cables ; One Serial ATA power cable ; One I/O shield ; One RAID driver diskette ; One “Mainboard Utility” CD ; One user’s manual

The system board and accessories in the package may not come similar to the information listed above. This may differ in accordance to the sales region or models in which it was sold. For more information about the standard package in your region, please contact your dealer or sales representative.

Before Using the System Board

Before using the system board, prepare basic system components.

If you are installing the system board in a new system, you will need at least the following internal components.

• A CPU

• Memory module

• Storage devices such as hard disk drive, CD-ROM, etc.

You will also need external system peripherals you intend to use which will normally include at least a keyboard, a mouse and a video display monitor.

Introduction

Chapter 1 - Introduction

Specifications

Processor

Front Side Bus

Chipset

System Memory

Expansion Slots

BIOS

Power Management

Hardware Monitor

Audio

LAN

• AMD® AthlonTM 64 X2 / Athlon 64 FX / AthlonTM 64 / Sempron

• Socket AM2

• 2000MT/s HyperTransport interface

• NVIDIA nForce4

Ultra (INFINITY NF ULTRA-M2)

NVIDIA nForce4TM (INFINITY NF-M2)

• Four 240-pin DDR2 DIMM sockets

• Supports DDR2 533 and DDR2 667 DIMMs

• Supports dual channel (128-bit wide) memory interface

• Supports up to 4GB system memory

• Supports unbuffered non-ECC x8 and x16 DIMMs

• 1 PCI Express x16 slot

• 2 PCI Express x1 slots

• 3 PCI slots

• Award BIOS

• 4Mbit flash memory

• ACPI and OS Directed Power Management

• ACPI STR (Suspend to RAM) function

• Wake-On-PS/2 Keyboard/Mouse

• Wake-On-USB Keyboard/Mouse

• Wake-On-LAN

• Wake-On-Ring

• RTC timer to power-on the system

• AC power failure recovery

• Monitors CPU/system/chipset temperature

• Monitors 12V/5V/3.3V/Vcore/Vbat/5Vsb/Vdimm/Vchip voltages

• Monitors the speed of the cooling fans

• CPU Overheat Protection function monitors CPU temperature during system boot-up

• Realtek ALC655 6-channel AC’97 audio CODEC

• True stereo line level outputs

• S/PDIF-in/out interface

• Realtek RTL8111 Gigabit PCIE LAN

• Fully compliant to IEEE 802.3 (10BASE-T), 802.3u (100BASETX) and 802.3ab (1000BASE-T) standards

Introduction

IDE with NVIDIA RAID

Serial ATA with RAID

IEEE 1394

Rear Panel I/O

Internal I/O

PCB

• Supports two IDE connectors that allow connecting up to four UltraDMA 133Mbps hard drives

• NVIDIA RAID allows RAID arrays spanning across Serial ATA and Parallel ATA

• RAID 0, RAID 1, RAID 0+1 and JBOD

• Four Serial ATA por ts

• SATA speed up to 3Gb/s (INFINITY NF ULTRA-M2) SATA speed up to 1.5Gb/s (INFINITY NF-M2)

• NVIDIA RAID allows RAID arrays spanning across Serial ATA and Parallel ATA

• RAID 0, RAID 1, RAID 0+1 and JBOD

• VIA VT6307

• Supports two 100/200/400 Mb/sec ports

• 1 mini-DIN-6 PS/2 mouse port

• 1 mini-DIN-6 PS/2 keyboard port

• 1 RCA S/PDIF-in port

• 1 RCA S/PDIF-out port

• 1 parallel port

• 1 COM port

• 1 IEEE 1394 port

• 1 RJ45 LAN port

• 4 USB 2.0/1.1 ports

• Line-in, line-out and mic-in jacks

• 3 connectors for 6 additional external USB 2.0/1.1 ports

• 1 connector for 1 external IEEE 1394 port

• 1 front audio connector for external line-out and mic-in jacks

• 1 CD-in internal audio connector

• 1 S/PDIF connector for optical cable connection

• 1 IrDA connector

• 4 Serial ATA connectors

• 2 IDE connectors

• 1 floppy connector

• 1 24-pin ATX power connector

• 1 4-pin ATX 12V power connector

• 1 front panel connector

• 3 fan connectors

• ATX form factor

• 22cm (8.66") x 30.5cm (12")

Introduction

Features

The system board supports the AMD AthlonTM 64 X2 / Athlon 64 FX / AthlonTM 64 / SempronTM processor for Socket AM2. AMD Athlon

64 provides superior computing for many software applications by allowing both 32-bit and 64-bit applications to run simultaneously on the same platform. The operating system and software are able to process more data and access a tremendous amount of memory which improves the overall system performance.

2T timing which provides better system stability is supported in CG or later revisions of the AMD Athlon

64 processor. You can select the memory timing in the Genie BIOS Setting submenu (“DRAM Configuration” section) of the BIOS.

The AMD Cool‘n’Quiet

technology allows

the system to detect the CPU’s tasks and utilization status. When the CPU’s task slows down, the system effectively lowers power consumption by lowering its CPU speed and voltage, subsequently decreasing its noise level.

PCI Express is a high bandwidth I/O infrastructure that possesses the ability to scale speeds by forming

multiple lanes. The system board currently supports the physical layer of x1 and x16 lane widths. The x1 PCI Express lane supports transfer rate of 2.5 Gigabytes (250MBbps) per second. The PCI Express architecture also provides a high performance graphics infrastructure by enhancing the capability of a x16 PCI Express lane to provide 4 Gigabytes per second transfer rate.

Cool‘n’Quiet

Introduction

CPU Overheat Protection has the capability of monitoring the CPU’s temperature during sys-

tem boot up. Once the CPU’s temperature exceeded the temperature limit pre-defined by the CPU, the system will automatically shutdown. This preventive measure has been added to protect the CPU from damage and insure a safe computing environment.

DDR2 is a higher performance DDR technology whose data transfer rate delivers bandwidth of 4.3 GB per second and beyond. That is twice the speed of the conventional DDR without increasing its power consump-

tion. DDR2 SDRAM modules work at 1.8V supply compared to

2.6V memory voltage for DDR modules. DDR2 also incorporates new innovations such as the On-Die Termination (ODT) as well as larger 4-bit pre-fetch against DDR which fetches 2 bits per clock cycle.

The onboard Realtek ALC655 is an AC’97 compatible audio codec that will support 6-channel audio only when the audio utility is configured to support this function. The mic-in at the rear will be disabled. Use the

front audio’s mic-in jack.

CPU Overheat Protection

Introduction

S/PDIF is a standard audio file transfer format that transfers digital audio signals to a device without having to be converted first to an analog format. This prevents the

quality of the audio signal from degrading whenever it is converted to analog. S/PDIF is usually found on digital audio equipment such as a DAT machine or audio processing device. The S/ PDIF connector on the system board sends surround sound and 3D audio signal outputs to amplifiers and speakers and to digital recording devices like CD recorders.

Serial ATA is a storage interface that is com-

pliant with SATA 1.0 specification. The system board supports 4 Serial ATA ports with speed of up to 3Gb/s (INFINITY NF ULTRA-M2) or 1.5Gb/s (INFINITY NF-M2). Serial ATA improves hard drive performance faster than the standard parallel ATA whose data transfer rate is 100MB/s.

The south bridge chip supports NVIDIA RAID (Redundant Array of Independent Disk) that allows RAID arrays spanning across 4 Serial ATA and Parallel ATA drives. It supports RAID 0, RAID 1, RAID 0+1 and JBOD.

The Realtek RTL8111 Gigabit PCIE LAN chip supports up to 1Gbps.

IEEE 1394 is fully compliant with the 1394 OHCI (Open Host Controller Interface) 1.1 specification. It supports up to 63 devices that can run simultaneously on a system.

1394 is a fast external bus standard that supports data transfer rates of up to 400Mbps. In addition to its high speed, it also supports isochronous data transfer which is ideal for video devices that need to transfer high levels of data in real-time. 1394 supports both Plug-and-Play and hot plugging.

Introduction

The system board is equipped with an IrDA connector

for wireless connectivity between your computer and peripheral devices. The IRDA (Infrared Data Association) specification supports data transfers of 115K baud at a distance of 1 meter.

The system board supports USB 2.0 and USB 1.1 ports. USB 1.1 supports 12Mb/second bandwidth while USB 2.0 supports 480Mb/second bandwidth providing

a marked improvement in device transfer speeds between your computer and a wide range of simultaneously accessible external Plug and Play peripherals.

This feature allows the system that is in the

Suspend mode or Soft Power Off mode to wake-up/power-on to respond to calls coming from an external modem or respond to calls from a modem PCI card that uses the PCI PME (Power Management Event) signal to remotely wake up the PC.

Important:

If you are using a modem add-in card, the 5VSB power source of your power supply must support a minimum of ≥720mA.

This feature allows the network to remotely

wake up a Soft Power Down (Soft-Off) PC. It is supported via the onboard LAN port or via a PCI LAN card that uses the PCI PME (Power Management Event) signal. However, if your system is in the Suspend mode, you can power-on the system only through an IRQ or DMA interrupt.

Important:

The 5VSB power source of your power supply must support

≥

720mA.

This function allows you to use the PS/2 keyboard or PS/2 mouse to power-on the sys-

tem.

Important:

The 5VSB power source of your power supply must support

≥

720mA.

Wake-On-LAN

IrDA

Wake-On-PS/2

Wake-On-Ring

Introduction

This function allows you to use a USB keyboard or USB mouse to wake up a system

from the S3 (STR - Suspend To RAM) state.

Important:

If you are using the Wake-On-USB Keyboard/Mouse function for 2 USB ports, the 5VSB power source of your power supply must support ≥1.5A. For 3 or more USB ports, the 5VSB power source of your power supply must support ≥2A.

The RTC installed on the system board allows your system to automatically power-on on the set date and

time.

The system board is designed to meet the ACPI (Ad-

vanced Configuration and Power Interface) specification. ACPI has energy saving features that enables PCs to implement Power Management and Plug-and-Play with operating systems that support OS Direct Power Management. Currently, only Windows

®®

2000/XP supports the ACPI function. ACPI when enabled in the Power Management Setup will allow you to use the Suspend to RAM function.

With the Suspend to RAM function enabled, you can power-off the system at once by pressing the power button or selecting “Standby” when you shut down Windows

®®

2000/XP without having to go through the sometimes tiresome process of closing files, applications and operating system. This is because the system is capable of storing all programs and data files during the entire operating session into RAM (Random Access Memory) when it powers-off. The operating session will resume exactly where you left off the next time you power-on the system.

Important:

The 5VSB power source of your power supply must support

≥

1A.

When power returns after an AC power failure, you may choose to either power-on the

system manually, let the system power-on automatically or return to the state where you left off before power failure occurs.

rtc

str

Wake-On-USB

power failure recovery

Introduction

Français

Processeur

Chipset

Mémoire Système

Logements d’Extension

BIOS

Gestion de Puissance

Fonctions de Moniteur de Matériel

Audio

LAN

• AMD® AthlonTM 64 X2 / Athlon 64 FX / AthlonTM 64 / Sempron

• Socket AM2

• Interface HyperTransport 2000MT/s

• NVIDIA nForce4

Ultra (INFINITY NF ULTRA-M2)

NVIDIA nForce4TM (INFINITY NF-M2)

• 4 socles DIMM DDR2 240-pin

• Supporte DDR2 533 et DDR2 667 DIMMs

• Supporte l’interface de mémoire deux canaux (128-bit)

• Supporte jusqu’à 4 GB de mémoire système

• Supporte exclusivement les modules DIMM non-ECC x8 et x16

• Supporte les DIMM non-tamponnés

• 1 slot PCI Express x16

• 2 slots PCI Express x1

• 3 slots PCI

• Compatible avec Award BIOS

• Mémoire Flash 4Mbit

• ACPI et OS Directed Power Management

• ACPI STR (Suspend to RAM) fonction

• Réveil-Sur-PS/2 Clavier/Souris

• Réveil-Sur-USB Clavier/Souris

• Eveil Sonnerie

• Réveil Par Le Réseau

• Minuterie RTC pour allumer le système

• Récupération après Défaillance d’Alimentation CA

• Gère l’alarme de température et de surchauffe de CPU/ système/chipset

• Gère l’alarme de voltage et d’échec de 12V/5V/3.3V/Vcore/ Vbat/5Vsb/Vdimm/Vchip

• Gère la vitesse de ventilateur du ventilateur

• Protection du CPU - supporte la mise hors circuit automatique en cas de surchauffage du système

• AC’97 CODEC Realtek ALC655 6-canaux

• Sorties de niveau de lignes stéréo vraies

• Interface entrée/sortie S/PDIF

• Realtek RTL8111 Gigabit PCIE LAN

• Supporte IEEE 802.3 (10BASE-T), 802.3u (100BASE-TX) et

802.3ab (1000BASE-T)

Caractéristiques et Spécifications

Introduction

IDE avec NVIDIA RAID

Serial ATA avec RAID

IEEE 1394

Panneau Arrière

I/O

Interne I/O

PCB

• Supporte des disques durs jusqu’à UltraDMA 133Mbps

• NVIDIA RAID permet des ensembles RAID sur toute l’étendue du port de série ATA et du parallèle ATA

• RAID 0, RAID 1, RAID 0+1 et JBOD

• 4 ports de série ATA

• Vitesse SATA jusqu’à 3Gb/s (INFINITY NF ULTRA-M2) Vitesse SATA jusqu’à 1.5Gb/s (INFINITY NF-M2)

• NVIDIA RAID permet des ensembles RAID sur toute l’étendue du port de série ATA et du parallèle ATA

• RAID 0, RAID 1, RAID 0+1 et JBOD

• VIA VT6307

• Supporte 2 100/200/400 Mb/sec ports

• 1 port souris PS/2

• 1 port clavier PS/2

• 1 port RCA S/PDIF-in

• 1 port RCA S/PDIF-out

• 1 port parallèle DB-25

• 1 port de DB-9 série

• 1 port IEEE 1394

• 1 port RJ45 LAN

• 4 ports USB 2.0/1.1

• Line-in, line-out (front R/L) et mic-in prises audio

•

3 connecteurs pour 6 ports USB 2.0/1.1 supplémentaires

• 1 connecteur pour 1 IEEE 1394

• 1 connecteur audio frontal pour les jacks de sortie externe et d’entrée micro

•1 connecteur CD-in audio internes

• 1 S/PDIF l’assemblage pour l’adjonction de câble optique

• 1 connecteur IR

• 4 ports de Série ATA

• 2 connecteurs IDE

• 1 connecteur de FDD

• 1 connecteur d’alimentation 24-pin ATX

• 1 connecteur d’alimentation 4-pin 12V ATX

• 1 connecteur devant panneau

• 3 connecteurs de ventilateurs

• Facteur de forme de ATX

• 22cm (8.66") x 30.5cm (12")

Introduction

Deutsch

Prozessor

Chipset

Systemspeicher

Expansion Schlitz

BIOS

Energie Management

Kleinteilmonitor

Audio

LAN

• AMD® AthlonTM 64 X2 / Athlon 64 FX / AthlonTM 64 / Sempron

• Socket AM2

• Interface HyperTransport 2000MT/s

• NVIDIA nForce4

Ultra (INFINITY NF ULTRA-M2)

NVIDIA nForce4TM (INFINITY NF-M2)

• 4 Sockel 240-pin DDR2 DIMM

• Unterhält DDR2 533 und DDR2 667 DIMMs

• Unterhält 128-bit – Speiher mit den zwei Kanälen

• Unterhält bis zum 4GB-Systemspeicher

• Unterhält nur non-ECC x8 und x16 DIMMs

• Unterhält DIMMs ohne Dämpfer

• 1 PCI Express x16-Einbauplätzen

• 2 PCI Express x1-Einbauplätzen

• 3 PCI-Einbauplätzen

• Kompatibilität mit Award BIOS

• Flash-Speicher (4Mbit)

• ACPI und OS Directed Power Management

• ACPI STR (Suspend to RAM) funktion

• Wecken bei Betätigung der PS/2 Tastatur/Maus

• Wecken bei USB-Tastatur/Maus

• Wecken bei Klingeln

• Wecken des Systems durch das Netzwerk

• RTC-Taktgeber zum Einschalten des Systems

• Wiederherstellung der Wechselstromversorgung nach einem Ausfall

• Überwachung der Temperatur des CPU/Systems/Chipset sowie Warnsignal bei Überhitzung

• Überwachung der Spannungen des 12V/5V/3.3V/Vcore/Vbat/ 5Vsb/Vdimm/Vchip

• Überwachung der Geschwindigkeit des Ventilators

• Prozessor-Shutz - Die Ausschaltung bei der Überhitzung – die automatische Ausschaltung des Computers bei der Überhitzung

• Realtek ALC655 6-Kanal, AC’97 Codec

• Naturgetreue Stereo-Leitungspegel-Ausgabe

• S/PDIF-In/Aus-Schnittstelle

• Realtek RTL8111 Gigabit PCIE LAN

• Unterstützt IEEE 802.3 (10BASE-T), 802.3u (100BASE-TX) und

802.3ab (1000BASE-T)

Leistungsmerkmale und Technische Daten

Introduction

IDE mit NVIDIA RAID

Serial ATA mit RAID

IEEE 1394

Porte an der Rückwand

Internes I/O

PCB

• Unterstützung der Festplatten bis zum UltraDMA 133Mbps

• NVIDIA RAID ermöglicht, dass die RAID-Arrays sowohl serielle als auch parallele ATA-Schnittstellen umfassen.

• RAID 0, RAID 1, RAID 0+1 und JBOD

• 4 serielle Serial ATA-Ports

• SATA bis zu 3Gb/s schnell (INFINITY NF ULTRA-M2) SATA bis zu 1.5Gb/s schnell (INFINITY NF-M2)

• NVIDIA RAID ermöglicht, dass die RAID-Arrays sowohl serielle als auch parallele ATA-Schnittstellen umfassen.

• RAID 0, RAID 1, RAID 0+1 und JBOD

• VIA VT6307

• Unterstützt 2 100/200/400 Mb/sec porte

• 1 Mini-DIN-6-Anschluß für eine PS/2-Maus

• 1 Mini-DIN-6-Anschluß für eine PS/2-Tastatur

• 1 S/PDIF-in RCA-Anschlüsse

• 1 S/PDIF-out RCA-Anschlüsse

• 1 Parallel-Anschlüsse

• 1 serieller DB-9-Anschlüsse

• 1 IEEE 1394-Anschlüsse

• 1 RJ45 LAN-Anschlüsse

• 4 USB 2.0/1.1-Anschlüsse

• Line-in, line-out (front R/L) und mic-in Audio-Anschlußbuchsen

•3

Anschlußfassung für 6 zusätzliche externe USB 2.0/1.1-

Anschlüsse

• 1 Anschluß für eine externe IEEE 1394 Schnittstelle

• 1 Front-Audioanschluss für externe Mikrofon-Ein- und – Ausgänge

• 1 CD-in interne Audioanschlüsse

• 1 S/PDIF Anschluß für die Verbindung des optischen Kabel

• 1 Anschluß für die IR-Schnittstelle

• 4 serielle Serial ATA-Ports

• 2 IDE-Anschlüsse

• 1 Floppy-Anschlüsse

• 1 24-polige Anschlußstecker für das ATX-Netzgerät

• 1 4-polige 12V Anschlußstecker für das ATX-Netzgerät

• 1 Vorderseite Füllung Anschlüsse

• 3-ventilator-Anschlüsse

• ATX Formfaktor

• 22cm (8.66") x 30.5cm (12")

Introduction

Español

Procesador

Chipset

Memoria de Sistema

Ranuras de Expansión

BIOS

Gerencia de la Energía

Monitor del Hardware

Audio

LAN

• AMD® AthlonTM 64 X2 / Athlon 64 FX / AthlonTM 64 / Sempron

• Socket AM2

• Interface de HyperTransport 2000MT/s

• NVIDIA nForce4

Ultra (INFINITY NF ULTRA-M2)

NVIDIA nForce4TM (INFINITY NF-M2)

• 4 240-pin DDR2 DIMM asientos

• Suporta DDR2 533 y DDR2 667 DIMMs

• Soporta memoria de dos canales (128-bit)

• Soporta hasta 4GB de memoria sistémica

• Soporta sólo non-ECC x8 y x16 DIMM

• Soporta unbuffered DIMM

• 1 slot PCI Express x16

• 2 slots PCI Express x1

• 3 slots PCI

• Award BIOS

• Memoria Instante (4Mbitios)

• ACPI y OS Directed Power Management

• ACPI STR (Suspend to RAM) función

• PS/2 Teclado/Ratón de Wake-On

• USB Teclado/Ratón de Wake-On

• Wake-On-LAN

• Wake-On-Ring

• Temporizador de RTC para encender el sistema

• Recuperación de Fracaso de Energía AC

• Monitores de los CPU/sistema/chipset temperaturas y alarma acalorada.

• Monitores de voltajes de 12V/5V/3.3V/Vcore/Vbat/5Vsb/ Vdimm/Vchip

• Vigila la velocidad del abanico del abanido

• Protección del procesador - Desconección en caso de recalentamiento –el ordenador se desconecta automáticamente en caso de recalentamiento

• Realtek ALC655 6-canal AC’97 CODEC

• Auténtico salidas de nivel de línea estéreo

• Interfáz de S/PDIF-in/out

• Realtek RTL8111 Gigabit PCIE LAN

• Soporta IEEE 802.3 (10BASE-T), 802.3u (100BASE-TX) y

802.3ab (1000BASE-T)

Características y Especificaciones

Introduction

IDE con NVIDIA RAID

Serial ATA con RAID

IEEE 1394

Panel Trasero I/O

Conectador Interno

PCB

• Soporta las unidades duras hasta de UltraDMA 133Mbps

• NVIDIA RAID permite RAID órdenes atravesando Serial ATA y Parallel ATA

• RAID 0, RAID 1, RAID 0+1 y JBOD

• 4 ports de Serial ATA

• SATA se acelera a 3Gb/s (INFINITY NF ULTRA-M2) SATA se acelera a 1.5Gb/s (INFINITY NF-M2)

• NVIDIA RAID permite RAID órdenes atravesando Serial ATA y Parallel ATA

• RAID 0, RAID 1, RAID 0+1 y JBOD

• VIA VT6307

• Soporta 2 ports 100/200/400 Mb/sec

• 1 puerto de ratón PS/2

• 1 puerto de teclado PS/2

• 1 puerto de S/PDIF-in RCA

• 1 puerto de S/PDIF-out RCA

• 1 puerto paralelo de DB-25

• 1 puerto de serie DB-9

• 1 puerto de IEEE 1394

• 1 puerto de RJ45 LAN

• 4 puertos de USB 2.0/1.1

• Line-in, line-out (front R/L) y mic-in enchufes de audio

• 3 conectores para 6 puertos de USB 2.0/1.1 externo adicional

• 1 conector para un puerto de IEEE 1394

• 1 connector de sonido delantera por linea externa y micrófono interno

• 1 conector de CD-in audio interno

• 1 S/PDIF mortaja para conección de cable óptico

• 1 conector de IR

• 4 ports de Serial ATA

• 2 conector de IDE

• 1 conector de FDD

• 1 conector 24-pin de fuente de alimentación de ATX

• 1 conector 4-pin 12V de fuente de alimentación de ATX

• 1 conector de panel delante

• 3 conectores de abanicos

• ATX forme el factor

• 22cm (8.66") x 30.5cm (12")

Introduction

Русский языкРусский язык

Русский язык

ПроцессорПроцессор

Процессор

ЧипсетЧипсет

Чипсет

ОперативнаяОперативная

Оперативная ПамятьПамять

ПамятьПамять

Память

управлениеуправление

управление силыñèëû

ñèëûñèëû

ñèëû

BIOSBIOS

BIOS

управлениеуправление

управление силыñèëû

ñèëûñèëû

ñèëû

монитормонитор

монитор оборудованияоборудования

оборудованияоборудования

оборудования

тональнозвуковотональнозвуково

тональнозвуково

• AMD® AthlonTM 64 X2 / Athlon 64 FX / AthlonTM 64 /

Sempron

• гнездо AM2

• Интерфейс системной шины 2000MT/s

• NVIDIA nForce4

Ultra (INFINITY NF ULTRA-M2)

NVIDIA nForce4TM (INFINITY NF-M2)

•4 240-pin DDR2 DIMM гнезда

•Поддерживает DDR2 533 и DDR2 667 DIMMs

•Поддерживает двухканальную память (128-бит)

•Поддерживает до 4ГБ системной памяти

•Поддерживает только non-ECC x8 и x16 DIMM

•Поддерживает небуфф. DIMM

• 1 PCI Express x16 слотов

• 2 PCI Express x1 слотов

• 3 PCI слотов

•Award BIOS

•4Mbit Flash Память

• ACPI è OS Directed Power Management

• ACPI STR (Suspend to RAM)

• Активизация На Движение Мыши

• Активизация На Нажатие Кнопки USB Клавиатуры

• Активизация На Входящий Звонок

• Активизация На Сетевое Событие

• RTC Таймер для Включения Системы

• Скачки Напряжения

• Mониторинг температуры процессора/системы/

Чипсет

• Mониторинг напряжений 12V/5V/3.3V/Vcore/Vbat/

5Vsb/Vdimm/Vchip

• Mониторинг скорости вращения вентилятора

• Защита процессора - Выключение при перегреве –

автоматическое выключение компьютера при перегреве

• Полнодуплексный Realtek ALC655 AC’97 codec 6-и

канальный звуковой выход

• Настоящий линейный стерео выход

• интерфейса S/PDIF-in/out

Характеристики и свойстваХарактеристики и свойства

Характеристики и свойства

Introduction

LANLAN

LAN

IDE c NVIDIAIDE c NVIDIA

IDE c NVIDIA RAIDRAID

RAIDRAID

RAID

Serial ASerial A

Serial A

A cA c

A c

RAIDRAID

RAID

IEEE 1394IEEE 1394

IEEE 1394

задняя панельзадняя панель

задняя панель I/OI/O

I/OI/O

I/O

внутренне внутренне

внутренне

I/OI/O

I/O

PCBPCB

PCB

•Realtek RTL8111 Gigabit PCIE LAN

• Поддержка IEEE 802.3 (10BASE-T), 802.3u (100BASE-

TX) è 802.3ab (1000BASE-T)

• Поддерживает жесткие диски до UltraDMA 133Mbps

• NVIDIA RAID позволяет создавать массивы RAID через

Serial ATA è Parallel ATA

• RAID 0, RAID 1, RAID 0+1 è JBOD

• 4 порта Serial ATA

• Скорость SATA до 3 ГБ/с (INFINITY NF ULTRA-M2)

Скорость SATA до 1.5 ГБ/с (INFINITY NF-M2)

• NVIDIA RAID позволяет создавать массивы RAID через

Serial ATA è Parallel ATA

• RAID 0, RAID 1, RAID 0+1 è JBOD

• VIA VT6307

• Поддерживает 2 100/200/400 Mb/sec порта

• 1 ìèíè-DIN-6 PS/2 ïîðò äëÿ ìûøè è

• 1 мини-DIN-6 PS/2 порт для клавиатуры

• 1 S/PDIF-in RCA ïîðò

• 1 S/PDIF-out RCA ïîðò

• 1 DB-25 параллельный порт

• 1 внешнего DB-9 порта

• 1 IEEE 1394 ïîðò

• 1 RJ45 LAN ïîðò

• 4 USB 2.0/1.1 порта

• Mic-in, line-in и line-out гнезда для звука

• 3 разъем для 6-х дополнительных внешних USB 2.0/

1.1 портов

• 1 разъем для внешнего IEEE 1394 порта

• 1 фронтальный аудио-разъем для внешнего

линейного и микрофонного выходов

• 1 CD-in внутренних звуковых разъема

• 1 S/PDIF разъем для присоединения оптического кабеля

• 1 разъем для интерфейса IR

• 4 порта Serial ATA

• 2 IDE разъема и

• 1 разъем

FDD

• 1 24-штырьковых разъемов питания ATX

• 1 4-штырьковых 12V разъемов питания ATX

• 1 Фронт панель разъем

• 3 Разъемы для вентилятора

• ATX

• 22cm (8.66") x 30.5cm (12")

Introduction

Hardware Installation

System Board Layout

Chapter 2 - Hardware Installation

INFINITY NF ULTRA-M2

Hardware Installation

INFINITY NF-M2

Hardware Installation

System Memory

Warning:

Electrostatic discharge (ESD) can damage your system board, processor, disk drives, add-in boards, and other components. Perform the upgrade instruction procedures described at an ESD workstation only. If such a station is not available, you can provide some ESD protection by wearing an antistatic wrist strap and attaching it to a metal part of the system chassis. If a wrist strap is unavailable, establish and maintain contact with the system chassis throughout any procedures requiring ESD protection.

The system board supports 240-pin DDR2 DIMM sockets. The four DDR2 DIMM sockets on the system board are divided into 2 channels:

Channel A - DDR2-1 and DDR2-3 Channel B - DDR2-2 and DDR2-4

DDR2-1, Channel A DDR2-2, Channel B

DDR2-3, Channel A DDR2-4, Channel B

Hardware Installation

The system board supports the following memory interface.

Single Channel (SC)

Data will be accessed in chunks of 64 bits (8B) from the memory channels.

Dual Channel (DC)

Data will be accessed in chunks of 128 bits from the memory channels. Dual channel provides better system performance because it doubles the data transfer rate.

• DIMMs are on the same channel.

• DIMMs in a channel can be identical or

completely different. However, we highly recommend using identical DIMMs.

• Not all slots need to be populated.

• DIMMs of the same memory configura-

tion are on different channels.

Single Channel

Dual Channel

The table below shows the DIMM sockets that must be populated with DIMMs for single or dual channel interface. We strongly recommend that you strictly follow the memory configurations below. Installing DDR2 DIMMs other than the recommended configurations may cause system boot failure.

DDR2-1

Dual Channel

Single Channel

DDR2-2

DDR2-3

DDR2-4

+ 113 hidden pages

DFI Infinity NF-ULTRA-M2, Infinity NF-M2 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual