#BRHH36
safe sleeper™ universal bed rail
READ ALL INSTRUCTIONS BEFORE FIRST USE.
Ages 2 Years – 6 Years
CAUTION: ADULT ASSEMBLY REQUIRED.
WARNING: IMPORTANT! KEEP FOR FUTURE REFERENCE!
• SUFFOCATION AND STRANGULATION HAZARD.
• Gaps in and around bed rails have entrapped young children and killed
infants.
• NEVER use with children younger than 2 years old. Use ONLY with older
children who can get in and out of adult bed without help. NEVER use in
place of crib.
• NEVER use unless bed rail is tight against mattress, without gaps, and at
least 9 in. from headboard and footboard. Do not fill gaps with pillows,
blankets, or other items that can suffocate children.
• NEVER use on toddler bed, bunk bed, waterbed, or bed with inflatable
mattress. Use ONLY on adult bed.
• Discontinue use if damaged, broken, or if parts are missing.
ASSEMBLY INSTRUCTIONS
Please follow these four easy steps to assemble this rail very quickly and WITHOUT TOOLS!
Figure A
Lay the 2 halves of the rail on the floor or table, so that the 3 Cross
Bars line up (Figure A). NOTE: Make sure Anchor Straps are not
1
twisted.
Connect the 3 Cross Bars by pressing them firmly into place
(Figure B).
2
Figure B
Figure B
Figure C
Slide Mesh Cover across the entire rail (Figure C),
then zip it closed (Figure D).
3
Figure D
Open Hinged Legs until hinges lock firmly into place (Figure E).
Assembly is now complete. Proceed to installation instructions.
4
Figure E
INSTALLATION AND USE INSTRUCTIONS FOR BEDS WITH BOX SPRINGS
01. Extend Anchor Strap and Plate to maximum length.
02. Insert Hinged Legs into place between mattress and box spring.
03. Extend Anchor Strap and Plate so that Anchor Plate is in position for
tightening. (Figure F)
04. Pull red striped tag toward you while pushing the Anchor Plate forward with
opposite hand, pressing Anchor Plate firmly against the mattress and box
spring. (Figure G)
05. Release grip on the red striped tag and pull the lower strap toward you until
Anchor Plate is snug against mattress and box spring. (Figure H)
IMPORTANT: To insure bed rail is tight as possible against mattress and
box spring, raise the mattress and tighten the strap slightly. Then lower the
mattress and pull the anchor plate back and firmly into place. Repeat this
step as needed and until tight.
06. Tuck remaining length of strap under the mattress, out of the way of children.
07. Lowering rail after installed on bed: This rail is designed with childproof
hinges for added safety. Therefore – to lower your rail - you must raise EACH
(both left and right) spring-loaded hinge at the same time. The hinges each
display an arrow pointing upwards in the direction you must raise the hinge to
disengage it. Once each spring is raised, you may gently lower the rail with
ease. This will allow you to easily change or make the bed. When you raise
the rail back to the upright position, the locks will automatically pop back into
place for safety.
box spring
Figure G
Figure G
mattress
anchor plate
Figure F
Figure H
Figure H
INSTALLATION AND USE INSTRUCTIONS FOR RECESSED PLATFORM STYLE BEDS
01. Anchor Strap & Plate are not needed for platform beds which have a solid
platform that is recessed at least 3 inches below the top of the bed frame.
Tuck Anchor Strap & Plate under the mattress, out of the way of children.
02. Insert Hinged Legs into place between mattress and recessed platform bed
support. (Figure I)
03. Make sure that rail is firmly in place between mattress and outside of bed
frame. (Figure J)
IMPORTANT: Always use a platform style mattress designed to fit your
recessed platform bed. Do not use a mattress that is too small (either in
length or width), because this may create dangerous gaps between the
sides or ends of the mattress and the inside edges of the recessed platform
bed frame. Tuck straps under mattress and out of the way of children.
04. Lowering rail after installed on bed: This rail is designed with childproof
hinges for added safety. Therefore – to lower your rail - you must raise EACH
(both left and right) spring-loaded hinge at the same time. The hinges each
display an arrow pointing upwards in the direction you must raise the hinge to
disengage it. Once each spring is raised, you may gently lower the rail with
ease. This will allow you to easily change or make the bed. When you raise
the rail back to the upright position, the locks will automatically pop back into
place for safety.
platform bed frame
mattress
Figure I
Figure J
CLEANING INSTRUCTIONS
Machine wash cold and hang dry, or surface wash with damp cloth.
DEX Products, Inc.
© 2016 DEX Products, Inc., dexbaby™, safe sleeper™, and the footprint logo are trademarks of DEX Products, Inc.
safe sleeper™ bed rail is Patent Pending. Patent infringement will be prosecuted to the full extent of the law. Made in China. 0116
www.dexbaby.com 800.546.1996 2019 East Monte Vista Ave. Suite #500, Vacaville, CA 95688
Loading...