DeWalt DCT414-XE Instruction Manual

DCT414-XE

10.8 V CORDLESS IR THERMOMETER

INSTRUCTION MANUAL

1

IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY DEWALT TOOL,
CALL US AT: 1800 654 155 (Aust) or 0800 339258 (NZ).

SAFETY INSTRUCTIONS FOR POWER TOOLS

When using power tools, always observe the safety regulations applicable in your
country to reduce the risk of fire, electric shock and personal injury. Read the following
safety instructions before attempting to operate this product. Keep these instructions in
a safe place.

WARNING: To reduce the risk of injury, read the instruction manual.

GENERAL POWER TOOL SAFETY WARNINGS

WARNING! Read all safety warnings and all instructions Failure to follow
the warnings and instructions may result in electric shock, fire and/or serious
injury.

The term “power tool” in the warnings refers to your mains-operated (corded) power
tool or battery-operated (cordless) power tool.

SAVE THESE INSTRUCTIONS

WORK AREA SAFETY
a) Keep work area clean and well lit. Cluttered or dark areas invite accidents.
b) Keep children and bystanders away while operating a power tool. Distractions

can cause you to lose control.

PERSONAL SAFETY
a) Stay alert, watch what you are doing and use common sense when operating

a power tool. Do not use a power tool while you are tired or under the
influence of drugs, alcohol or medication. A moment of inattention while

operating power tools may result in serious personal injury.

b) Use personal protective equipment. Always wear eye protection. Protective

equipment such as dust mask, non-skid safety shoes, hard hat, or hearing
protection used for appropriate conditions will reduce personal injuries.

c) Prevent unintentional starting. Ensure the switch is in the off position before

connecting to power source and/or battery pack, picking up or carrying the
tool. Carrying power tools with your finger on the switch or energising power

tools that have the switch on invites accidents.

d) Do not overreach. Keep proper footing and balance at all times. This enables

better control of the power tool in unexpected situations.

e) Dress properly. Do not wear loose clothing or jewelery. Keep your hair,

clothing and gloves away from moving parts. Loose clothes, jewellery or long

hair can be caught in moving parts.

POWER TOOL USE AND CARE
a) Do not use the power tool if the switch does not turn it on and off. Any power

tool that cannot be controlled with the switch is dangerous and must be repaired.

b) Disconnect the plug from the power source and/or the battery pack from the

power tool before making any adjustments, changing accessories, or storing
power tools. Such preventive safety measures reduce the risk of starting the

power tool accidentally.

c) Store idle power tools out of the reach of children and do not allow persons

unfamiliar with the power tool or these instructions to operate the power tool.

Power tools are dangerous in the hands of untrained users.

Definitions: Safety Guidelines

The definitions below describe the level of severity for each
signal word. Please read the manual and pay attention to these
symbols.

DANGER: Indicates an imminently hazardous situation

which, if not avoided, will result in death or serious injury.

WARNING: Indicates a potentially hazardous situation

which, if not avoided, could result in death or serious injury.

CAUTION: Indicates a potentially hazardous situation which,

if not avoided, may result in minor or moderate injury.
NOTICE: indicates a practice not related to personal injury

which, if not avoided, may result in property damage.

2

d) Maintain power tools. Check for misalignment or binding of moving parts,

breakage of parts and any other condition that may affect the power tool’s
operation. If damaged, have the power tool repaired before use. Many

accidents are caused by poorly maintained power tools.

e) Use the power tool, accessories and tool bits, etc. in accordance with these

instructions, taking into account the working conditions and the work to be
performed. Use of the power tool for operations different from those intended

could result in a hazardous situation.

BATTERY TOOL USE AND CARE
a) Recharge only with the charger specified by the manufacturer. A charger that

is suitable for one type of battery pack may create a risk of fire when used with
another battery pack.

b) Use power tools only with specifically designated battery packs. Use of any

other battery packs may create a risk of injury and fire.

c) When battery pack is not in use, keep it away from other metal objects like

paper clips, coins, keys, nails, screws, or other small metal objects that can
make a connection from one terminal to another. Shorting the battery terminals

together may cause burns or a fire.

d) Under abusive conditions, liquid may be ejected from the battery; avoid

contact. If contact accidentally occurs, flush with water. If liquid contacts
eyes, additionally seek medical help. Liquid ejected from the battery may cause

irritation or burns.

SERVICE
a) Have your power tool serviced by a qualified repair person using only

identical replacement parts. This will ensure that the safety of the power tool is

maintained.

Electrical Safety

The electric motor has been designed for one voltage only. Always check that the
power supply corresponds to the voltage on the rating plate. 230 V AC means your
tool will operate on alternating current. As little as 10% lower voltage can cause loss
of power and can result in overheating. All DEWALT tools are factory tested; if this
tool does not operate, check the power supply. Your DEWALT tool is double insulated,
therefore no earth wire is required.

• Young children and the infirm. This appliance is not intended for use by
young children or infirm persons without supervision. Young children should be
supervised to ensure that they do not play with this appliance.

• Replacement of the supply cord. If the supply cord is damaged, it must be
replaced by the manufacturer or an authorised DEWALT Service Centre in order
to avoid a hazard.

Extension Cords

CAUTION: Use only extension cords that are approved by the country’s Electrical
Authority. Before using extension cords, inspect them for loose or exposed wires,
damaged insulation and defective fittings. Replace the cord if necessary.

MINIMUM GAUGE FOR CORD SETS
For Cable length (m): 7.5 15 25 30 45 60
Use Cable with minimum rating (Amperes)
Tool Amperes

0 - 3.4 7.5 7.5 7.5 7.5 7.5 7.5

3.5 - 5.0 7.5 7.5 7.5 7.5 10 15

5.1 - 7.0 10 10 10 10 15 15

7.1 - 12.0 15 15 15 15 20 20

12.1 - 20.0 20 20 20 20 25 –

Safety Information for Lasers and IR Thermometers

WARNING: Laser Radiation Exposure. Do not disassemble or modify the
IR thermometers. There are no user serviceable parts inside. Serious eye injury
could result.

WARNING: Hazardous Radiation. Use of controls or adjustments or performance

of procedures other than those specified herein may result in hazardous radiation
exposure.

• Do not operate the IR thermometers in explosive atmospheres, such as in the

presence of flammable liquids, gases, or dust. Power tools create sparks which
may ignite the dust or fumes.

• Use the IR thermometer only with the specifically designated DEWALT

batteries. Use of any other batteries may create a risk of fire.

• Store the IR thermometer out of reach of children and other untrained

persons. Lasers are dangerous in the hands of untrained users.

3

• Tool service must be performed only by qualified repair personnel. Service
or maintenance performed by unqualified personnel may result in injury. To
locate your nearest D

EWALT service center call (AUS) 1800 654 155 or

(NZ) 0800 339258

• Do not use optical tools such as a telescope or transit to view the laser beam.
Serious eye injury could result.

• Do not place the IR thermometer in a position which may cause anyone to
intentionally or unintentionally stare into the laser beam. Serious eye injury
could result.

• Do not disassemble the IR thermometer. There are no user serviceable parts
inside.

• Do not modify the IR thermometer in any way. Modifying the tool may result in
hazardous laser radiation exposure.

• Do not operate the IR thermometer around children or allow children to
operate the IR thermometer. Serious eye injury may result.

• Do not remove or deface warning labels. Removing labels increases the risk of
exposure to radiation.

• Do not use IR thermometer for testing temperatures of cooked or uncooked
food.

• Do not use for taking of humans or animals body temperature.

CAUTION: Use of controls or adjustments or performance of procedures other

than those specified herein may result in hazardous radiation exposure.

• The label on your tool may include the following symbols.

V ............................volts

mW ........................milliwatts

................Laser warning symbol

nm ..........................wavelength in nanometers

2.............................Class 2 Laser

3a ..........................Class 3a Laser

WARNING LABELS

For your convenience and safety, the following label is on your IR thermometer
(Fig. 2).

WARNING: LASER RADIATION DO NOT STARE INTO BEAM CLASS 2 LASER

PRODUCT MAXIMUM OUTPUT POWER <1mW.

WARNING: ALWAYS wear approved protective safety equipment complying with

the following standards:

• Eye protection: AS/NZS1337 Eye Protectors for Industrial Applications;

• Hearing protection: AS/NZS1270 Acoustics – Hearing Protection;

• Respiratory protection: AS/NZS1716 Respiratory Protective Devices.

WARNING: We recommend the use of a residual current device with a residual

current rating of 30mA or less.

CAUTION: When not in use, place tool on its side on a stable surface where it

will not cause a tripping or falling hazard. Some tools with large battery packs will

stand upright on the battery pack but may be easily knocked over.

Important Safety Instructions for All Battery Packs

When ordering replacement battery packs, be sure to include catalog number and
voltage. Consult the chart at the end of this manual for compatibility of chargers and
battery packs.

The battery pack is not fully charged out of the carton. Before using the battery pack
and charger, read the safety instructions below. Then follow charging procedures
outlined.

READ ALL INSTRUCTIONS

• Do not charge or use battery in explosive atmospheres, such as in the
presence of flammable liquids, gases or dust. Inserting or removing the battery

from the charger may ignite the dust or fumes.

• Never force battery pack into charger. Do not modify battery pack in any
way to fit into a non-compatible charger as battery pack may rupture
causing serious personal injury. Consult the chart at the end of this manual for

compatibility of batteries and chargers.

• Charge the battery packs only in DEWALT chargers.

• DO NOT splash or immerse in water or other liquids.

• Do not store or use the tool and battery pack in locations where the
temperature may reach or exceed 40˚C (105°F) (such as outside sheds or
metal buildings in summer).