DeWalt DCS551 User Manual

ADVERTENCIA: LÉASE ESTE

........................

INSTRUCTIVO ANTES DE USAR EL PRODUCTO.

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y

PÓLIZA DE GARANTÍA.

Si tiene dudas o comentarios, contáctenos.

If you have questions or comments, contact us.

Pour toute question ou tout commentaire, nous contacter.

1-800-4-DEWALT • www.dewalt.com

DCS551

20V Max* Cut Out Tool

INSTRUCTION MANUAL

GUIDE D’UTILISATION

MANUAL DE INSTRUCCIONES

DEWALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286

The following are trademarks for one or more DEWALT power tools: the yellow and black color scheme, the “D” shaped
air intake grill, the array of pyramids on the handgrip, the kit box configuration, and the array of lozenge-shaped humps on
the surface of the tool.

(MAR14) Part No. N382917 DCS551 Copyright © 2014 D

EWALT

Defi nitions: Safety Guidelines

The definitions below describe the level of severity for each signal word. Please read the
manual and pay attention to these symbols.

DANGER: Indicates an imminently hazardous situation which, if not avoided, will

result in death or serious injury.

WARNING: Indicates a potentially hazardous situation which, if not avoided, could

result in death or serious injury.

CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result

in minor or moderate injury.
NOTICE: Indicates a practice not related to personal injury which, if not avoided, may

result in property damage.

IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY DEWALT TOOL, CALL US
TOLL FREE AT: 1-800-4-D

WARNING: To reduce the risk of injury, read the instruction manual.

General Power Tool Safety Warnings

WARNING! Read all safety warnings and all instructions. Failure to follow the warnings
and instructions may result in electric shock, fire and/or serious injury.

SAVE ALL WARNINGS AND INSTRUCTIONS

The term "power tool" in the warnings refers to your mains-operated (corded) power tool or battery­operated (cordless) power tool.

1) WORK AREA SAFETY

a) Keep work area clean and well lit. Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive atmospheres, such as in the presence of

flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or
fumes.

c) Keep children and bystanders away while operating a power tool. Distractions can

cause you to lose control.

2) ELECTRICAL SAFETY

a) Power tool plugs must match the outlet. Never modify the plug in any way. Do not use

any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching

outlets will reduce risk of electric shock.

b) Avoid body contact with earthed or grounded surfaces such as pipes, radiators,

ranges and refrigerators. There is an increased risk of electric shock if your body is earthed
or grounded.

c) Do not expose power tools to rain or wet conditions. Water entering a power tool will

increase the risk of electric shock.

d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the

power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or
entangled cords increase the risk of electric shock.

e) When operating a power tool outdoors, use an extension cord suitable for outdoor

use. Use of a cord suitable for outdoor use reduces the risk of electric shock.

f) If operating a power tool in a damp location is unavoidable, use a ground fault circuit

interrupter (GFCI) protected supply. Use of a GFCI reduces the risk of electric shock.

3) PERSONAL SAFETY

a) Stay alert, watch what you are doing and use common sense when operating a

power tool. Do not use a power tool while you are tired or under the influence of
drugs, alcohol or medication. A moment of inattention while operating power tools may

result in serious personal injury.

b) Use personal protective equipment. Always wear eye protection. Protective equipment

such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate
conditions will reduce personal injuries.

c) Prevent unintentional starting. Ensure the switch is in the off position before

connecting to power source and/or battery pack, picking up or carrying the tool.

Carrying power tools with your finger on the switch or energizing power tools that have the
switch on invites accidents.

d) Remove any adjusting key or wrench before turning the power tool on. A wrench or a

key left attached to a rotating part of the power tool may result in personal injury.

e) Do not overreach. Keep proper footing and balance at all times. This enables better

control of the power tool in unexpected situations.

f) Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing and

gloves away from moving parts. Loose clothes, jewelry or long hair can be caught in moving
parts.

g) If devices are provided for the connection of dust extraction and collection facilities,

ensure these are connected and properly used. Use of dust collection can reduce dust­related hazards.

4) POWER TOOL USE AND CARE

a) Do not force the power tool. Use the correct power tool for your application. The

correct power tool will do the job better and safer at the rate for which it was designed.

b) Do not use the power tool if the switch does not turn it on and off. Any power tool that

cannot be controlled with the switch is dangerous and must be repaired.

c) Disconnect the plug from the power source and/or the battery pack from the power

tool before making any adjustments, changing accessories, or storing power tools.

Such preventive safety measures reduce the risk of starting the power tool accidentally.

d) Store idle power tools out of the reach of children and do not allow persons unfamiliar

with the power tool or these instructions to operate the power tool. Power tools are
dangerous in the hands of untrained users.

e) Maintain power tools. Check for misalignment or binding of moving parts, breakage

of parts and any other condition that may affect the power tool’s operation. If
damaged, have the power tool repaired before use. Many accidents are caused by poorly

maintained power tools.

f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting

edges are less likely to bind and are easier to control.

g) Use the power tool, accessories and tool bits, etc. in accordance with these

instructions, taking into account the working conditions and the work to be
performed. Use of the power tool for operations different from those intended could result in

a hazardous situation.

5) BATTERY TOOL USE AND CARE

a) Recharge only with the charger specified by the manufacturer. A charger that is suitable

for one type of battery pack may create a risk of fire when used with another battery pack.

b) Use power tools only with specifically designated battery packs. Use of any other

battery packs may create a risk of injury and fire.

c) When battery pack is not in use, keep it away from other metal objects, like paper

clips, coins, keys, nails, screws, or other small metal objects, that can make a
connection from one terminal to another. Shorting the battery terminals together may

cause burns or a fire.

d) Under abusive conditions, liquid may be ejected from the battery; avoid contact. If

contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek
medical help. Liquid ejected from the battery may cause irritation or burns.

EWALT (1-800-433-9258).

FOR FUTURE REFERENCE

Outil à découper 20V max*

6) SERVICE

a) Have your power tool serviced by a qualified repair person using only identical

replacement parts. This will ensure that the safety of the power tool is maintained.

Additional Specifi c Safety Rules for Cut-Out Tools

• Use clamps or another practical way to secure and support the workpiece to a stable
platform. Holding the work by hand or against your body leaves it unstable and may lead to loss

of control.

• Hold power tools by insulated gripping surfaces when performing an operation where
the cutting tool may contact hidden wiring. Contact with a "live" wire will make exposed

metal parts of the tool "live" and shock the operator.

WARNING: After changing bits or making any adjustments, make sure the collet nut is securely

tightened to avoid injury.

WARNING: Do not press spindle lock or collet lock buttons while motor is running. The operator

may lose control and drop the tool. Personal injury or serious tool damage may result.

WARNING: Shut off all live electric circuits to any areas where cut outs will be made, to avoid fire

or serious personal injury.

CAUTION: Do not touch the bit or collet nut during or immediately after cutting material. The bit

and collet nut may be hot enough to burn bare skin.

• Do not run tool while carrying at your side. The spinning bit may become entangled with
clothing and injury may occur.

• Always wear eye protection. Dust mask and hearing protection must be used for appropriate
conditions. Using personal safety devices is recommended. WORK SAFE.

• Always operate the tool with the depth guide in place. The guide keeps the bit from plunging
too deeply through the material. A minimum of penetration should be maintained to eliminate the
danger of cutting into electric wiring.

• Do not use this tool with drill or screwdriver bits. This tool is not intended to be used as a
drill or screwdriver.

• Be sure your cutting bits are sharp and in good condition. Damaged bits can cause the tool
to jump, injuring the operator.

• Never touch the bit immediately after use. It may be extremely hot.

• Always follow the bit manufacturer’s speed recommendations as some bit designs
require specific speeds for safety or performance. If you are unsure of the proper speed or
are experiencing any type of problem, contact the bit manufacturer.

• Be sure that the motor has stopped completely before you lay the tool down. If the cutter
head is still spinning when the tool is layed down, it could cause injury or damage.

• Be sure that the bit is clear of the workpiece before starting motor. If the bit is in contact
with the workpiece when the motor starts it could make the tool jump, causing damage or injury.

• If your tool fails to function properly, take it to an authorized service center. There are no
user serviceable parts inside this tool and it should only be opened by trained service personnel.

• Air vents often cover moving parts and should be avoided. Loose clothes, jewelry or long
hair can be caught in moving parts.

WARNING: ALWAYS use safety glasses. Everyday eyeglasses are NOT safety glasses. Also use

face or dust mask if cutting operation is dusty. ALWAYS WEAR CERTIFIED SAFETY EQUIPMENT:

• ANSI Z87.1 eye protection (CAN/CSA Z94.3),

• ANSI S12.6 (S3.19) hearing protection,

• NIOSH/OSHA/MSHA respiratory protection.

WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other

construction activities contains chemicals known to the State of California to cause cancer, birth
defects or other reproductive harm. Some examples of these chemicals are:

• lead from lead-based paints,

• crystalline silica from bricks and cement and other masonry products, and

• arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you do this type of work. To reduce
your exposure to these chemicals: work in a well ventilated area, and work with approved safety

Recortadora de 20 V Máx*

equipment, such as those dust masks that are specially designed to filter out microscopic particles.

• Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling, and

other construction activities. Wear protective clothing and wash exposed areas with
soap and water. Allowing dust to get into your mouth, eyes, or lay on the skin may promote

absorption of harmful chemicals.

WARNING: Use of this tool can generate and/or disperse dust, which may cause serious and

permanent respiratory or other injury. Always use NIOSH/OSHA approved respiratory protection
appropriate for the dust exposure. Direct particles away from face and body.

WARNING: Always wear proper personal hearing protection that conforms to ANSI

S12.6 (S3.19) during use. Under some conditions and duration of use, noise from this product

may contribute to hearing loss.

CAUTION: When not in use, place tool on its side on a stable surface where it will not

cause a tripping or falling hazard. Some tools with large battery packs will stand upright on the

battery pack but may be easily knocked over.

• The label on your tool may include the following symbols. The symbols and their definitions are as
follows:

V ...................... volts A ......................... amperes

Hz .................... hertz W ........................ watts

min .................. minutes

or DC ..... direct current or AC/DC ...... alternating or direct current

.................... Class I Construction

........................ (grounded) n .......................... rated speed

................... Class II Construction ........................ earthing terminal

........................ (double insulated) ........................ safety alert symbol

…/min ............. per minute BPM .................... beats per minute

IPM .................. impacts per minute RPM .................... revolutions per minute

SPM ................ strokes per minute sfpm .................... surface feet per minute

or AC ............. alternating current

n

o ........................ no load speed

Important Safety Instructions for All Battery Packs

When ordering replacement battery packs, be sure to include the catalog number and voltage.
Consult the chart at the end of this manual for compatibility of chargers and battery packs.

The battery pack is not fully charged out of the carton. Before using the battery pack and
charger, read the safety instructions below and then follow charging procedures outlined.

READ ALL INSTRUCTIONS

• Do not charge or use the battery pack in explosive atmospheres, such as in the
presence of flammable liquids, gases or dust. Inserting or removing the battery pack

from the charger may ignite the dust or fumes.

• NEVER force the battery pack into the charger. DO NOT modify the battery pack in
any way to fit into a non-compatible charger as battery pack may rupture causing
serious personal injury. Consult the chart at the end of this manual for compatibility of

batteries and chargers.

• Charge the battery packs only in designated D

EWALT chargers.

• DO NOT splash or immerse in water or other liquids.

• Do not store or use the tool and battery pack in locations where the temperature
may reach or exceed 105°F (40 °C) (such as outside sheds or metal buildings in
summer). For best life store battery packs in a cool, dry location.

NOTE: Do not store the battery packs in a tool with the trigger switch locked on.

Never tape the trigger switch in the ON position.

WARNING: Fire hazard. Never attempt to open the battery pack for any reason. If the battery

pack case is cracked or damaged, do not insert into the charger. Do not crush, drop or damage
the battery pack. Do not use a battery pack or charger that has received a sharp blow, been
dropped, run over or damaged in any way (e.g., pierced with a nail, hit with a hammer, stepped
on). Damaged battery packs should be returned to the service center for recycling.

WARNING: Fire hazard. Do not store or carry the battery pack so that metal objects

can contact exposed battery terminals. For example, do not place the battery pack in

aprons, pockets, tool boxes, product kit boxes, drawers, etc., with loose nails, screws, keys, etc.

Transporting batteries can possibly cause fires if the battery terminals inadvertently
come in contact with conductive materials such as keys, coins, hand tools and the
like. The US Department of Transportation Hazardous Material Regulations (HMR) actually

prohibit transporting batteries in commerce or on airplanes (e.g., packed in suitcases and carry­on luggage) UNLESS they are properly protected from short circuits. So when transporting
individual battery packs, make sure that the battery terminals are protected and well insulated
from materials that could contact them and cause a short circuit.

SPECIFIC SAFETY INSTRUCTIONS FOR LITHIUM ION (Li-Ion)

• Do not incinerate the battery pack even if it is severely damaged or is completely
worn out. The battery pack can explode in a fire. Toxic fumes and materials are created

when lithium ion battery packs are burned.

• If battery contents come into contact with the skin, immediately wash area with
mild soap and water. If battery liquid gets into the eye, rinse water over the open eye for
15 minutes or until irritation ceases. If medical attention is needed, the battery electrolyte is
composed of a mixture of liquid organic carbonates and lithium salts.

• Contents of opened battery cells may cause respiratory irritation. Provide fresh air. If
symptoms persist, seek medical attention.

WARNING: Burn hazard. Battery liquid may be flammable if exposed to spark or flame.

The RBRC™ Seal

The RBRC™ (Rechargeable Battery Recycling Corp oration) Seal on the nickel
cadmium, nickel metal hydride or lithium ion batteries (or battery packs) indicate
that the costs to recycle these batteries (or battery packs) at the end of their useful
life have already been paid by D

EWALT. In some areas, it is illegal to place spent

nickel cadmium, nickel metal hydride or lithium ion batteries in the trash or
municipal solid waste stream and the RBRC program provides an environmentally
conscious alternative.

RBRC™, in cooperation with D

EWALT and other battery users, has established programs in

the United States and Canada to facilitate the collection of spent nickel cadmium, nickel metal
hydride or lithium ion batteries. Help protect our environment and conserve natural resources by
returning the spent nickel cadmium, nickel metal hydride or lithium ion batteries to an authorized

EWALT service center or to your local retailer for recycling. You may also contact your local

D
recycling center for information on where to drop off the spent battery.

RBRC™ is a registered trademark of the Rechargeable Battery Recycling Corporation.

Important Safety Instructions for All Battery Chargers

SAVE THESE INSTRUCTIONS: This manual contains important safety and operating
instructions for battery chargers.

• Before using the charger, read all instructions and cautionary markings on the charger,
battery pack and product using the battery pack.

WARNING: Shock hazard. Do not allow any liquid to get inside the charger. Electric shock

may result.

CAUTION: Burn hazard. To reduce the risk of injury, charge only DEWALT rechargeable

battery packs. Other types of batteries may overheat and burst resulting in personal injury and
property damage.

NOTICE: Under certain conditions, with the charger plugged into the power supply, the charger
can be shorted by foreign material. Foreign materials of a conductive nature, such as, but not
limited to, grinding dust, metal chips, steel wool, aluminum foil or any buildup of metallic particles
should be kept away from the charger cavities. Always unplug the charger from the power supply
when there is no battery pack in the cavity. Unplug the charger before attempting to clean.

• DO NOT attempt to charge the battery pack with any chargers other than the ones
in this manual. The charger and battery pack are specifically designed to work together.

• These chargers are not intended for any uses other than charging D
rechargeable batteries. Any other uses may result in risk of fire, electric shock or
electrocution.

• Do not expose the charger to rain or snow.

EWALT

• Pull by the plug rather than the cord when disconnecting the charger. This will

reduce the risk of damage to the electric plug and cord.

• Make sure that the cord is located so that it will not be stepped on, tripped over or

otherwise subjected to damage or stress.

• Do not use an extension cord unless it is absolutely necessary. Use of improper

extension cord could result in risk of fire, electric shock or electrocution.

• When operating a charger outdoors, always provide a dry location and use an
extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces
the risk of electric shock.

• An extension cord must have adequate wire size (AWG or American Wire Gauge)
for safety. The smaller the gauge number of the wire, the greater the capacity of the cable,
that is, 16 gauge has more capacity than 18 gauge. An undersized cord will cause a drop in
line voltage resulting in loss of power and overheating. When using more than one extension
to make up the total length, be sure each individual extension contains at least the minimum
wire size. The following table shows the correct size to use depending on cord length and
nameplate ampere rating. If in doubt, use the next heavier gauge. The lower the gauge number,
the heavier the cord.

Minimum Gauge for Cord Sets

Volts Total Length of Cord in Feet (meters)

Ampere Rating

More
Than

0 6 18 16 16 14

610 18161412
10 12 16 16 14 12
12 16 14 12 Not Recommended

Not More

Than

120V 25 (7.6) 50 (15.2) 100 (30.5) 150 (45.7)
240V 50 (15.2) 100 (30.5) 200 (61.0) 300 (91.4)

AWG

• Do not place any object on top of the charger or place the charger on a soft surface
that might block the ventilation slots and result in excessive internal heat. Place the

charger in a position away from any heat source. The charger is ventilated through slots in
the top and the bottom of the housing.

• Do not operate the charger with a damaged cord or plug.

• Do not operate the charger if it has received a sharp blow, been dropped or
otherwise damaged in any way. Take it to an authorized service center.

• Do not disassemble the charger; take it to an authorized service center when service
or repair is required. Incorrect reassembly may result in a risk of electric shock, electrocution
or fire.

• Disconnect the charger from the outlet before attempting any cleaning. This will
reduce the risk of electric shock. Removing the battery pack will not reduce this risk.

• NEVER attempt to connect 2 chargers together.

• The charger is designed to operate on standard 120V household electrical power.
Do not attempt to use it on any other voltage. This does not apply to the vehicular
charger.

Chargers

Your tool uses a DEWALT charger. Be sure to read all safety instructions before using your charger.
Consult the chart at the end of this manual for compatibility of chargers and battery packs.

Charging Procedure (Fig. 2)

1. Plug the charger into an appropriate outlet before inserting the battery pack.

2. Insert the battery pack (G) into the charger, as shown in Figure 2, making sure the pack

is fully seated in charger. The red (charging) light will blink continuously, indicating that the
charging process has started.

3. The completion of charge will be indicated by the red light remaining ON continuously. The

pack is fully charged and may be used at this time or left in the charger.

Indicator Light Operation

DCB101

PACK CHARGING

PACK CHARGED

HOT/COLD DELAY

PROBLEM PACK OR CHARGER

x

PROBLEM POWERLINE

DCB107, DCB112

PACK CHARGING

PACK CHARGED

HOT/COLD DELAY

Charge Indicators

This charger is designed to detect certain problems that can arise. Problems are indicated by
the red light flashing at a fast rate. If this occurs, re-insert the battery pack into the charger. If the
problem persists, try a different battery pack to determine if the charger is working properly. If
the new pack charges correctly, then the original pack is defective and should be returned to a
service center or other collection site for recycling. If the new battery pack elicits the same trouble
indication as the original, have the charger and the battery pack tested at an authorized service
center.

HOT/COLD DELAY
DCB101

This charger has a hot/cold delay feature: when the charger detects a battery that is hot, it
automatically starts a delay, suspending charging until the battery has cooled. After the battery
has cooled, the charger automatically switches to the pack charging mode. This feature ensures
maximum battery life. The red light flashes long, then short while in the hot/cold delay mode.

DCB107, DCB112

The DCB107 and DCB112 chargers have a hot/cold delay feature. When the charger detects
a battery that is hot, it automatically delays charging until the battery has cooled. When the
charger detects a battery that is cold, it automatically delays charging until the battery has
warmed.

The red light will continue to blink, but a yellow indicator light will be illuminated during this
operation. Once the battery has cooled, the yellow light will turn off and the charger will resume
the charging procedure.

LEAVING THE BATTERY PACK IN THE CHARGER

The charger and battery pack can be left connected with the charge indicator showing Pack
Charged.

WEAK BATTERY PACKS: Weak batteries will continue to function but should not be expected
to perform as much work.

FAULTY BATTERY PACKS: This charger will not charge a faulty battery pack. The charger will
indicate faulty battery pack by refusing to light or by displaying problem pack or charger.

NOTE: This could also mean a problem with a charger.
PROBLEM POWER LINE

Some chargers have a Problem Power Line indicator. When the charger is used with some
portable power sources such as generators or sources that convert DC to AC, the charger may
temporarily suspend operation, flashing the red light with two fast blinks followed by a pause. This
indicates the power source is out of limits.

Wall Mounting

DCB107, DCB112

These chargers are designed to be wall mountable or to sit upright on a table or work surface.
If wall mounting, locate the charger within reach of an electrical outlet. Mount the charger

securely using drywall screws at least 1” (25.4 mm) long, screwed into wood to an optimal depth
leaving approximately 7/32” (5.5 mm) of the screw exposed.

Important Charging Notes

1. Longest life and best performance can be obtained if the battery pack is charged when the

air temperature is between 65°F and 75°F (18° – 24°C). DO NOT charge the battery pack
in an air temperature below +40°F (+4.5°C), or above +105°F (+40.5°C). This is important
and will prevent serious damage to the battery pack.

2. The charger and battery pack may become warm to the touch while charging. This is a

normal condition, and does not indicate a problem. To facilitate the cooling of the battery
pack after use, avoid placing the charger or battery pack in a warm environment such as in
a metal shed or an uninsulated trailer.

3. A cold battery pack will charge at about half the rate of a warm battery pack. The battery

pack will charge at that slower rate throughout the entire charging cycle and will not return
to maximum charge rate even if the battery pack warms.

4. If the battery pack does not charge properly:

a. Check operation of receptacle by plugging in a lamp or other appliance;
b. Check to see if receptacle is connected to a light switch which turns power off when you

turn out the lights;

c. Move the charger and battery pack to a location where the surrounding air temperature

is approximately 65 °F – 75°F (18° – 24°C);

d. If charging problems persist, take the tool, battery pack and charger to your local service

center.

5. The battery pack should be recharged when it fails to produce sufficient power on jobs

which were easily done previously. DO NOT CONTINUE to use under these conditions.
Follow the charging procedure. You may also charge a partially used pack whenever you
desire with no adverse effect on the battery pack.

6. Foreign materials of a conductive nature such as, but not limited to, grinding dust, metal

chips, steel wool, aluminum foil, or any buildup of metallic particles should be kept away
from charger cavities. Always unplug the charger from the power supply when there is no
battery pack in the cavity. Unplug the charger before attempting to clean.

7. Do not freeze or immerse the charger in water or any other liquid.

WARNING: Shock hazard. Don’t allow any liquid to get inside the charger. Electric shock

may result.

WARNING: Burn hazard. Do not submerge the battery pack in any liquid or allow any liquid

to enter the battery pack. Never attempt to open the battery pack for any reason. If the plastic
housing of the battery pack breaks or cracks, return to a service center for recycling.

Storage Recommendations

1. The best storage place is one that is cool and dry, away from direct sunlight and excess heat

or cold.

2. For long storage, it is recommended to store a fully charged battery pack in a cool dry place

out of the charger for optimal results.

NOTE: Battery packs should not be stored completely depleted of charge. The battery pack will
need to be recharged before use.

FIG. 1

F

C

B

FIG. 2 FIG. 3 FIG. 4

G

E

G

D

FIG. 5

A

I

H

J

G

I

SAVE THESE INSTRUCTIONS FOR FUTURE USE

COMPONENTS (Fig. 1, 4)

WARNING: Never modify the power tool or any part of it. Damage or personal injury could result.

A. ON/OFF switch
B. Cutting depth guide
C. Collet nut
D. Collet lock button
E. Spindle lock button

INTENDED USE

This cut out tool is designed for professional cut out applications.
DO NOT use under wet conditions or in presence of flammable liquids or gases.
This cut out tool is a professional power tool. DO NOT let children come into contact with the tool.

Supervision is required when inexperienced operators use this tool.

F. LED worklight
G. Battery Pack
H. Battery fuel gauge
I. Battery release button

ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of serious personal injury, turn tool off and remove the

battery pack before making any adjustments or removing/installing attachments or
accessories.

An accidental start-up can cause injury.

Installing and Removing the Bit (Fig. 1)

This tool is designed for spiral cutting bits with either a 1/8" (3 mm) or 1/4" (6 mm) shank and
has a tool-free bit change system. To change bits, FIRST turn off the tool and disconnect the
battery from the tool. Remove the depth guide (B).

1. To replace bit, depress both spindle lock (E) and collet lock (D) and turn collet grip
counterclockwise.

2. Insert or remove bit.

WARNING: The bits are sharp and should be handled with great care.
CAUTION: When replacing bits, do not insert cutting flutes into the collet. This may result in

broken bits.

3. While depressing both spindle and collet locks, turn the collet grip clockwise to firmly tighten
the collet. For some heavy duty applications, it may be necessary to use a wrench to further
tighten the nut (C) while depressing the spindle lock (E).

4. Attach guide.

CAUTION: Never tighten the collet without a bit installed.

This tool comes with both 1/8" (3 mm) and 1/4" (6 mm) collets. To change collets, remove the
collet nut and insert the desired collet.

Depth Guide (Fig. 1, 5)

Depth guide (B) snaps onto locators as shown. Keep depth guide in place at all times during operation
of the tool. For best results, adjust the guide using the knob to allow the bit to protrude about 1/8"

past the material to be cut.

mm)

(3

OPERATION

WARNING: To reduce the risk of serious personal injury, turn tool off and remove the

battery pack before making any adjustments or removing/installing attachments or
accessories.

An accidental start-up can cause injury.

Installing and Removing the Battery Pack (Fig. 3)

NOTE: For best results, make sure your battery pack is fully charged.
To install the battery pack (G) into the tool handle, align the battery pack with the rails inside the

tool’s handle and slide it into the handle until the battery pack is firmly seated in the tool and
ensure that it does not disengage.

To remove the battery pack from the tool, press the release button (I) and firmly pull the battery
pack out of the tool handle. Insert it into the charger as described in the charger section of this
manual.

FUEL GAUGE BATTERY PACKS (FIG. 4)

Some D
indicate the level of charge remaining in the battery pack.

To actuate the fuel gauge, press and hold the fuel gauge button (J). A combination of the three green
LED lights will illuminate designating the level of charge left. When the level of charge in the battery
is below the usable limit, the fuel gauge will not illuminate and the battery will need to be recharged.

NOTE: The fuel gauge is only an indication of the charge left on the battery pack. It does not indicate
tool functionality and is subject to variation based on product components, temperature and end-user
application.

For more information regarding fuel gauge battery packs, please call 1-800-4-D
(1-800-433-9258) or visit our website www.dewalt.com.

EWALT battery packs include a fuel gauge which consists of three green LED lights that

EWALT

To Maintain Safe Tool Control

• Make sure the work surface is free of nails or screws. Cutting into a nail or screw may

cause the tool to jump, damaging the bit.

• Never operate the tool with one hand while holding the workpiece with the other hand.

Always clamp the material and guide the tool with both hands.

Do not cut material lying on a hard surface. Clearance behind material to be cut must be

•

allowed for protruding bit.

Disconnect battery from tool before making adjustments, changing bits, or cleaning tool.

•

Do not start the tool with bit engaged in the material. The bit may grab the material.

•

Switch (Fig. 1)

To start the motor, slide the switch (A) to "I" position. To stop the motor, slide the switch to "O" position.

Cutting a Hole for an Electrical Outlet (Fig. 5)

WARNING: Shut off all live electric circuits to any areas where cut outs will be made.

1. Push any wiring deeply into the outlet box to avoid damage from the cutting bit.

2. Before hanging the sheet covering the outlet, mark the approximate location of the center of the
outlet on the wall board. Check the cutting bit depth against the side of the board to be sure it
will cut entirely through the material.

3. Tack the sheet in place with a few fasteners avoiding the stud holding the outlet. This allows the
wall board to flex slightly around the protruding fixture box.

4. Turn the cut-out tool on. Holding the tool firmly with both hands, plunge the bit straight into the
center of the outlet.

5. Cut to the right until the edge of the box is touched. Pull out just enough for the bit to clear the
edge of the box. Plunge in again holding the bit gently against the outside of the box.

6. Follow the outside of the box as shown keeping slight pressure against the box. This will minimize
wandering and give you a clean precise cut.

7. Remove the waste and dust from the outlet. Finish fastening the sheet of wall board.

MAINTENANCE

WARNING: To reduce the risk of serious personal injury, turn tool off and remove the

battery pack before making any adjustments or removing/installing attachments or
accessories.

An accidental start-up can cause injury.

Cleaning

WARNING: Blow dirt and dust out of all air vents with clean, dry air at least once a week. To

minimize the risk of eye injury, always wear ANSI Z87.1 approved eye protection when performing this.

WARNING: Never use solvents or other harsh chemicals for cleaning the non-metallic parts of the

tool. These chemicals may weaken the plastic materials used in these parts. Use a cloth dampened
only with water and mild soap. Never let any liquid get inside the tool; never immerse any part of the
tool into a liquid.

CHARGER CLEANING INSTRUCTIONS

WARNING: Shock hazard. Disconnect the charger from the AC outlet before cleaning. Dirt and

grease may be removed from the exterior of the charger using a cloth or soft non-metallic brush. Do
not use water or any cleaning solutions.

Accessories

WARNING: Since accessories, other than those offered by DEWALT, have not been tested with this

product, use of such accessories with this tool could be hazardous. To reduce the risk of injury, only
D

EWALT recommended accessories should be used with this product.

Recommended accessories for use with your tool are available at extra cost from your local dealer or
authorized service center. If you need assistance in locating any accessory, please contact D
Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286, call 1-800-4-D

9258) or visit our website: www.dewalt.com.

EWALT (1-800-433-

EWALT

Repairs

The charger and battery pack are not serviceable.
To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment (including brush

inspection and replacement) should be performed by a D
authorized service center or other qualified service personnel. Always use identical replacement parts.

EWALT factory service center, a DEWALT

Register Online

Thank you for your purchase. Register your product now for:

• WARRANTY SERVICE: Registering your product will help you obtain more efficient warranty

service in case there is a problem with your product.

• CONFIRMATION OF OWNERSHIP: In case of an insurance loss, such as fire, flood or theft,

your registration of ownership will serve as your proof of purchase.

• FOR YOUR SAFETY: Registering your product will allow us to contact you in the unlikely event

a safety notification is required under the Federal Consumer Safety Act.

Register online at www.dewalt.com/register.

Three Year Limited Warranty

DEWALT will repair, without charge, any defects due to faulty materials or workmanship for three years
from the date of purchase. This warranty does not cover part failure due to normal wear or tool abuse.
For further detail of warranty coverage and warranty repair information, visit www.dewalt.com or call
1-800-4-D
where repairs have been made or attempted by others. This warranty gives you specific legal rights
and you may have other rights which vary in certain states or provinces.

In addition to the warranty, D

D

EWALT will maintain the tool and replace worn parts caused by normal use, for free, any time during

the first year after purchase.

EWALT (1-800-433-9258). This warranty does not apply to accessories or damage caused

EWALT tools are covered by our:

1 YEAR FREE SERVICE

2 YEARS FREE SERVICE ON DEWALT BATTERY PACKS

DC9071, DC9091, DC9096, DC9280, DC9360, DC9180, DCB120, DCB201 and DCB203

3 YEARS FREE SERVICE ON D

DCB200, DCB204

EWALT BATTERY PACKS

DEWALT BATTERY PACKS

Product warranty voided if the battery pack is tampered with in any way. DEWALT is not responsible
for any injury caused by tampering and may prosecute warranty fraud to the fullest extent permitted
by law.

90 DAY MONEY BACK GUARANTEE

If you are not completely satisfied with the performance of your D
for any reason, you can return it within 90 days from the date of purchase with a receipt for a full
refund – no questions asked.

LATIN AMERICA: This warranty does not apply to products sold in Latin America. For products sold
in Latin America, see country specific warranty information contained in the packaging, call the local
company or see website for warranty information.

FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or are missing,
call 1-800-4-D

EWALT (1-800-433-9258) for a free replacement.

EWALT Power Tool, Laser, or Nailer

Défi nitions: lignes directrices en

matière de sécurité

Les définitions ci-dessous décrivent le niveau de danger pour chaque
mot-indicateur employé. Lire le mode d’emploi et porter une attention particulière à ces
symboles.

DANGER : indique une situation dangereuse imminente qui, si elle n’est pas évitée,

entraînera la mort ou des blessures graves.

AVERTISSEMENT: indique une situation potentiellement dangereuse qui, si elle n’est

pas évitée, pourrait entraîner la mort ou des blessures graves.

ATTENTION : indique une situation potentiellement dangereuse qui, si elle n’est pas

évitée, pourrait entraîner des blessures légères ou modérées.
AVIS : indique une pratique ne posant aucun risque de dommages corporels mais

qui par contre, si rien n’est fait pour l’éviter, pourrait poser des risques de dommages

matériels.

POUR TOUTE QUESTION OU REMARQUE AU SUJET DE CET OUTIL OU DE TOUT AUTRE OUTIL

EWALT, COMPOSEZ LE NUMÉRO SANS FRAIS : 1-800-4-DEWALT (1-800-433-9258).

D

AVERTISSEMENT : afin de réduire le risque de blessures, lire le mode d’emploi de l’outil.

Avertissements de sécurité généraux pour les outils
électriques

AVERTISSEMENT! lire tous les avertissements de sécurité et toutes les directives.
Le non-respect des avertissements et des directives pourrait se solder par un choc électrique,
un incendie et/ou une blessure grave.

CONSERVER TOUS LES AVERTISSEMENTS ET TOUTES LES

DIRECTIVES POUR UN USAGE ULTÉRIEUR

Le terme " outil électrique " cité dans les avertissements se rapporte à votre outil électrique à
alimentation sur secteur (avec fil) ou par piles (sans fil).

1) SÉCURITÉ DU LIEU DE TRAVAIL

a) Tenir l’aire de travail propre et bien éclairée. Les lieux encombrés ou sombres sont

propices aux accidents.

b) Ne pas faire fonctionner d’outils électriques dans un milieu déflagrant, tel qu’en

présence de liquides, de gaz ou de poussières inflammables. Les outils électriques
produisent des étincelles qui pourraient enflammer la poussière ou les vapeurs.

c) Éloigner les enfants et les personnes à proximité pendant l’utilisation d’un outil

électrique. Une distraction pourrait en faire perdre la maîtrise à l’utilisateur.

2) SÉCURITÉ EN MATIÈRE D’ÉLECTRICITÉ

a) Les fiches des outils électriques doivent correspondre à la prise. Ne jamais modifier la

fiche d’aucune façon. Ne jamais utiliser de fiche d’adaptation avec un outil électrique
mis à la terre. Le risque de choc électrique sera réduit par l’utilisation de fiches non modifiées

correspondant à la prise.

b) Éviter tout contact physique avec des surfaces mises à la terre comme des tuyaux,

des radiateurs, des cuisinières et des réfrigérateurs. Le risque de choc électrique est plus
élevé si votre corps est mis à la terre.

c) Ne pas exposer les outils électriques à la pluie ou à l’humidité. La pénétration de l’eau

dans un outil électrique augmente le risque de choc électrique.

d) Ne pas utiliser le cordon de façon abusive. Ne jamais utiliser le cordon pour

transporter, tirer ou débrancher un outil électrique. Tenir le cordon éloigné de
la chaleur, de l’huile, des bords tranchants et des pièces mobiles. Les cordons

endommagés ou enchevêtrés augmentent les risques de choc électrique.

e) Pour l’utilisation d’un outil électrique à l’extérieur, se servir d’une rallonge convenant

à cette application. L’utilisation d’une rallonge conçue pour l’extérieur réduira les risques de
choc électrique.

f) S’il est impossible d’éviter l’utilisation d’un outil électrique dans un endroit humide,

brancher l’outil dans une prise ou sur un circuit d’alimentation dotés d’un disjoncteur
de fuite à la terre (GFCI). L’utilisation de ce type de disjoncteur réduit les risques de choc

électrique.

3) SÉCURITÉ PERSONNELLE

a) Être vigilant, surveiller le travail effectué et faire preuve de jugement lorsqu’un outil

électrique est utilisé. Ne pas utiliser d’outil électrique en cas de fatigue ou sous
l’influence de drogues, d’alcool ou de médicaments. Un simple moment d’inattention en

utilisant un outil électrique peut entraîner des blessures corporelles graves.

b) Utiliser des équipements de protection individuelle. Toujours porter une protection

oculaire. L’utilisation d’équipements de protection comme un masque antipoussière, des
chaussures antidérapantes, un casque de sécurité ou des protecteurs auditifs lorsque la
situation le requiert réduira les risques de blessures corporelles.

c) Empêcher les démarrages intempestifs. S’assurer que l’interrupteur se trouve à la

position d’arrêt avant de relier l’outil à une source d’alimentation et/ou d’insérer un
bloc-piles, de ramasser ou de transporter l’outil. Transporter un outil électrique alors que

le doigt repose sur l’interrupteur ou brancher un outil électrique dont l’interrupteur est à la
position de marche risque de provoquer un accident.

d) Retirer toute clé de réglage ou clé avant de démarrer l’outil. Une clé ou une clé de

réglage attachée à une partie pivotante de l’outil électrique peut provoquer des blessures
corporelles.

e) Ne pas trop tendre les bras. Conserver son équilibre en tout temps. Cela permet de

mieux maîtriser l’outil électrique dans les situations imprévues.

f) S’habiller de manière appropriée. Ne pas porter de vêtements amples ni de bijoux.

Garder les cheveux, les vêtements et les gants à l’écart des pièces mobiles. Les
vêtements amples, les bijoux ou les cheveux longs risquent de rester coincés dans les pièces
mobiles.

g) Si des composants sont fournis pour le raccordement de dispositifs de dépoussiérage

et de ramassage, s’assurer que ceux-ci sont bien raccordés et utilisés. L’utilisation d’un
dispositif de dépoussiérage peut réduire les dangers engendrés par les poussières.

4) UTILISATION ET ENTRETIEN D’UN OUTIL ÉLECTRIQUE

a) Ne pas forcer un outil électrique. Utiliser l’outil électrique approprié à l’application.

L’outil électrique approprié effectuera un meilleur travail, de façon plus sûre et à la vitesse pour
laquelle il a été conçu.

b) Ne pas utiliser un outil électrique dont l’interrupteur est défectueux. Tout outil

électrique dont l’interrupteur est défectueux est dangereux et doit être réparé.

c) Débrancher la fiche de la source d’alimentation et/ou du bloc-piles de l’outil

électrique avant de faire tout réglage ou changement d’accessoire ou avant de
ranger l’outil. Ces mesures préventives réduisent les risques de démarrage accidentel de

l’outil électrique.

d) Ranger les outils électriques hors de la portée des enfants et ne permettre à aucune

personne n’étant pas familière avec un outil électrique ou son mode d’emploi
d’utiliser cet outil. Les outils électriques deviennent dangereux entre les mains d’utilisateurs

inexpérimentés.

e) Entretien des outils électriques. Vérifier si les pièces mobiles sont mal alignées ou

coincées, si des pièces sont brisées ou présentent toute autre condition susceptible
de nuire au bon fonctionnement de l’outil électrique. En cas de dommage, faire
réparer l’outil électrique avant toute nouvelle utilisation. Beaucoup d’accidents sont

causés par des outils électriques mal entretenus.

f) S’assurer que les outils de coupe sont aiguisés et propres. Les outils de coupe bien

entretenus et affûtés sont moins susceptibles de se coincer et sont plus faciles à maîtriser.

g) Utiliser l’outil électrique, les accessoires, les forets, etc. conformément aux présentes

directives en tenant compte des conditions de travail et du travail à effectuer.

L’utilisation d’un outil électrique pour toute opération autre que celle pour laquelle il a été conçu
est dangereuse.

5) UTILISATION ET ENTRETIEN DU BLOC-PILES

a) Ne recharger l’outil qu’au moyen du chargeur précisé par le fabricant. L’utilisation d’un

chargeur qui convient à un type de bloc-piles risque de provoquer un incendie s’il est utilisé
avec un autre type de b loc-piles.

b) Utiliser les outils électriques uniquement avec les blocs-piles conçus à cet effet.

L’utilisation de tout autre bloc-piles risque de causer des blessures ou un incendie.

c) Lorsque le bloc-piles n’est pas utilisé, le tenir éloigné des objets métalliques,

notamment des trombones, de la monnaie, des clés, des clous, des vis ou autres
petits objets métalliques qui peuvent établir une connexion entre les deux bornes. Le

court-circuit des bornes du bloc-piles risque de provoquer des brûlures ou un incendie.

d) En cas d’utilisation abusive, le liquide peut gicler hors du bloc-piles; éviter tout

contact avec ce liquide. Si un contact accidentel se produit, laver à grande eau. Si
le liquide entre en contact avec les yeux, obtenir également des soins médicaux. Le

liquide qui gicle hors du bloc-piles peut provoquer des irritations ou des brûlures.

6) RÉPARATION

a) Faire réparer l’outil électrique par un réparateur professionnel en n’utilisant que des

pièces de rechange identiques. Cela permettra de maintenir une utilisation sécuritaire de

l’outil électrique.

Régles de sécurité additionnelles particuliéres concernant les
outils à découper

• Utilisez des serres de fixation ou un autre dispositif de fixation permettant de soutenir

et de retenir la pièce sur une plate-forme stable. Tenir la pièce avec la main ou contre son

corps n’est pas suffisamment stable et risque de provoquer une perte de maîtrise de l’outil.

• Tenir l’outil par sa surface de prise isolée dans une situation où l’outil de coupe peut

entrer en contact avec un câblage caché. Tout contact avec un fil " sous tension " mettra "
sous tension " les pièces métalliques de l’outil et causera un choc électrique à l’opérateur de l’outil.

AVERTISSEMENT : Pour prévenir toute blessure, s’assurer que l’écrou de la douille de serrage

est fermement serré après tout changement d’organe de coupe ou réglage.

AVERTISSEMENT : Ne pas appuyer sur le bouton de verrouillage de la broche ou celui de l’écrou

de la douille lorsque le moteur est en marche. L’utilisateur pourrait alors perdre le contrôle de l’outil et
le laisser tomber, et risquer de se blesser ou d’endommager sérieusement l’outil.

AVERTISSEMENT : Pour prévenir tout risque d’incendie ou de blessure, couper le courant

électrique là où toute découpe doit être faite.

ATTENTION : Ne pas toucher l’organe de coupe ou l’écrou de la douille pendant ou immédiatement

après toute coupe. Ces derniers pourraient être assez chauds pour provoquer des brûlures.

• Ne pas faire fonctionner l’outil tout en le transportant à son côté. L’organe de coupe en

tournant pourrait s’accrocher aux vêtements et provoquer des blessures.

• Toujours porter des lunettes de protection. Porter un masque anti-poussières et un

protecteur auditif lorsque la situation le requiert. L’utilisation de dispositifs individuels de sécurité
est recommandée. TRAVAILLER EN TOUTE SÉCURITÉ.

• Toujours utiliser l’outil avec son guide de profondeur en place. Le guide empêche l’organe

de coupe de pénétrer dans le matériau trop profondément. Maintenir un minimum de pénétration
pour éliminer tout risque de couper des fils électriques.

• Ne pas utiliser cet outil comme une perceuse ou un tournevis électrique. Il n’a pas été

conçu à cet effet.

• S’assurer que tout organe de coupe est bien aiguisé et en bonne condition. Des organes

de coupes endommagés peuvent provoquer les tressautements de l’outil et blesser l’utilisateur.

• Ne jamais toucher l’organe de coupe immédiatement après usage. Il pourrait être

extrêmement chaud.

• Suivre systématiquement les recommandations de vitesse du fabricant, car certaines

fraises nécessitent de tourner à des vitesses spécifiques pour des raisons de sécurité
ou de performances.

Si l’on n’est pas sûr de la vitesse adéquate ou si l’on rencontre un

problème quelconque, contacter le fabricant des fraises.

• S’assurer que le moteur est à l’arrêt complet avant de poser l’outil. Le fait de poser l’outil

alors que l’organe de coupe continue de tourner pose des risques de blessure ou de dommage
matériel.

• S’assurer que l’organe de coupe ne touche pas la pièce à travailler avant de mettre l’outil

en marche. Le fait de les mettre en contact pendant la mise en marche du moteur pourrait faire
tressauter l’outil et poser des risques de blessure ou de dommage matériel.

• Si l’outil ne fonctionne pas correctement, l’apporter à un centre de service autorisé.

Cet outil ne comporte aucune pièce réparable par l’utilisateur et ne doit être ouvert que par du
personnel qualifié.

• Prendre des précautions à proximité des évents, car ils cachent des pièces mobiles.

Vêtements amples, bijoux ou cheveux longs risquent de rester coincés dans ces pièces mobiles.

AVERTISSEMENT : porter SYSTEMATIQUEMENT des lunettes de protection. Les lunettes

courantes NE sont PAS des lunettes de protection. Utiliser aussi un masque antipoussières si
la découpe doit en produire beaucoup. PORTER SYSTÉMATIQUEMENT UN ÉQUIPEMENT DE
SÉCURITÉ HOMOLOGUÉ:

• Protection oculaire ANSI Z87.1 (CAN/CSA Z94.3);

• Protection auditive ANSI S12.6 (S3.19);

• Protection des voies respiratoires NIOSH/OSHA/MSHA.

AVERTISSEMENT: les scies, meules, ponceuses, perceuses ou autres outils de construction

peuvent produire des poussières contenant des produits chimiques reconnus par l’État
californien pour causer cancers, malformations congénitales ou être nocifs au système
reproducteur. Parmi ces produits chimiques, on retrouve:

• Le plomb dans les peintures à base de plomb;

• La silice cristallisée dans les briques et le ciment, ou autres produits de maçonnerie; et

• L’arsenic et le chrome dans le bois ayant subi un traitement chimique.

Le risque associé à de telles expositions varie selon la fréquence à laquelle on effectue ces travaux.
Pour réduire toute exposition à ces produits : travailler dans un endroit bien aéré, en utilisant du
matériel de sécurité homologué, tel un masque antipoussières spécialement conçu pour filtrer les
particules microscopiques.

• Limiter toute exposition prolongée avec les poussières provenant du ponçage, sciage,

meulage, perçage ou toute autre activité de construction. Porter des vêtements de
protection et nettoyer à l’eau savonneuse les parties du corps exposées. Le fait de laisser

la poussière pénétrer dans la bouche, les yeux ou la peau peut favoriser l’absorption de produits
chimiques dangereux.

AVERTISSEMENT: cet outil peut produire et/ou répandre de la poussière susceptible de causer

des dommages sérieux et permanents au système respiratoire. Utiliser systématiquement un appareil
de protection des voies respiratoires homologué par le NIOSH ou l’OSHA. Diriger les particules dans
le sens opposé au visage et au corps.

AVERTISSEMENT : pendant l’utilisation, porter systématiquement une protection

auditive individuelle adéquate homologuée ANSI S12.6 (S3.19). Sous certaines conditions et

suivant la durée d’utilisation, le bruit émanant de ce produit pourrait contribuer à une perte de l’acuité
auditive.

ATTENTION: après utilisation, ranger l’outil sur son côté, sur une surface stable, là

où il ne pourra ni faire trébucher ni faire chuter quelqu’un. Certains outils équipés d’un

large bloc-piles peuvent tenir à la verticale sur celui-ci, mais manquent alors de stabilité.

• L’étiquette apposée sur votre outil peut inclure les symboles suivants. Les symboles et leur

définition sont indiqués ci-après:

V ......................volts A .........................ampères

Hz ....................hertz W ........................watts

min ..................minutes

ou DC .....courant continu ou AC/DC .....courant alternatif ou

....................classe I fabrication continu

(mis à la terre)

...................fabrication classe II n .........................vitesse nominale

(double isolation)

…/min .............par minute

IPM ..................impacts par minute BPM ...................battements par minute

sfpm ................pieds linéaires par minute (plpm) r/min ...................tours par minute

SPM (FPM) ......fréquence par minute

ou AC ...........courant alternatif

n

o .......................vitesse à vide

.......................borne de terre

........................symbole d’avertissement

Consignes importantes de sécurité propres à tous les blocs­piles

Pour commander un bloc-piles de rechange, s’assurer d’inclure son numéro de catalogue et sa
tension. Consulter le tableau en dernière page de ce manuel pour connaître les compatibilités entre
chargeurs et blocs-piles.

Le bloc-piles n’est pas totalement chargé d’usine. Avant d’utiliser le bloc-piles et le chargeur, lire les
consignes de sécurité ci-dessous. Puis suivre la procédure de charge indiquée.

LIRE TOUTES LES CONSIGNES

• Ne pas recharger ou utiliser un bloc-piles en milieu déflagrant, en présence, par
exemple, de poussières, gaz ou liquides inflammables. Le fait d’insérer ou retirer un bloc-

piles de son chargeur pourrait causer l’inflammation de poussières ou d’émanations.

• NE JAMAIS forcer l’insertion d’un bloc-piles dans un chargeur. NE modifier un bloc-piles
d’AUCUNE façon pour le faire rentrer dans un chargeur incompatible, car il pourrait se
briser et causer des dommages corporels graves. Consulter le tableau en dernière page de

ce manuel pour connaître les compatibilités entre chargeurs et blocs-piles.

• Recharger les blocs-piles exclusivement dans des chargeurs D

• NE PAS éclabousser le bloc-piles ou l’immerger dans l’eau ou dans tout autre liquide.

• Ne pas entreposer ou utiliser l’appareil et le bloc-piles en présence de températures

ambiantes pouvant excéder 40°C (105°F) (comme dans des hangars ou des bâtiments
métalliques l’été). Pour préserver leur durée de vie, entreposer les blocs-piles dans un endroit

frais et sec.

REMARQUE: ne pas mettre un bloc-piles dans un outil dont la gâchette est verrouillée

en position de marche. Ne jamais bloquer l’interrupteur en position de MARCHE.

AVERTISSEMENT: risques d’incendie. Ne jamais tenter d’ouvrir le bloc-piles pour quelque raison

que ce soit. Si le boîtier du bloc-piles est fissuré ou endommagé, ne pas l’insérer dans un chargeur.
Ne pas écraser, laisser tomber, ou endommager les blocs-piles. Ne pas utiliser un bloc-piles ou un
chargeur qui a reçu un choc violent, ou si l’appareil est tombé, a été écrasé ou endommagé de
quelque façon que ce soit (p. ex. percé par un clou, frappé d’un coup de marteau, piétiné). Les
blocs-piles endommagés doivent être renvoyés à un centre de réparation pour y être recyclés.

AVERTISSEMENT: risques d’incendie. Au moment de ranger ou transporter le bloc­piles, s’assurer qu’aucun objet métallique n’entre en contact avec les bornes à découvert
du bloc-piles. Par exemple, éviter de placer un bloc-piles dans un tablier, une poche, une boîte
à outils ou un tiroir, etc. contenant des objets tels que des clous, des vis, des clés, etc. Le fait
de transporter des bloc-piles comporte des risques d’incendie, car les bornes des piles
pourraient entrer, par inadvertance, en contact avec des objets conducteurs, tels que: clés,
pièces de monnaie, outils ou autres. La réglementation sur les produits dangereux (Hazardous

Material Regulations) du département américain des transports interdit, en fait, le transport des
piles pour le commerce ou dans les avions (ex: dans les bagages enregistrés ou à main) À MOINS
qu’elles ne soient correctement protégées contre tout court-circuit. Aussi lors du transport individuel

EWALT.