DeWalt DCS393 TYPE 1 Owner’s Manual

If you have questions or comments, contact us.

Pour toute question ou tout commentaire, nous contacter.

Si tiene dudas o comentarios, contactenos.

INSTRUCTION MANUAL
GUIDE D'UTILISATION
MANUAL DE INSTRUCCIONES

INSTRUCTIVO DE OPERACION, CENTROS DE SERVICIO Y POLIZA DE
GARANT[A. ADVERTENOIA: LEASE ESTE INSTRUCTIVO ANTES DE

USAR EL PRODUCTO.

DCS391, DCS393
20V Max* 6-1/2" (165 mm) Cordless Circular Saw

Scie circulaire sans fil de 20 V max* 165 mm
Sierra circular inal_mbrica de 20 V M_x* 165 mm

®

DCS391, DCS393 20V Max* 6-1/2" Cordless Circular Saw 5250 RPM

L

K

A

\

A. TRIGGER SWITCH LOCK-OFF BUqq-ON
B. TRIGGER SWITCH

C. BATTERY PACK

D. DEPTH ADJUSTMENT KNOB
E. SHOE

E LOWER BLADE GUARD RETRACTING LEVER

G. LOWER BLADE GUARD

A

M

M

H. BLADE CLAMPING SCREW

I. KERF INDICATOR

J. BEVEL ADJUSTMENT KNOB
K. BLADE LOCK BUTTON (not shown)

L. AUXILIARY HANDLE

M. BATTERY RELEASE BUTTON

N. BLADE WRENCH

Definitions: Safety Guidelines

The definitions below describe the level of severity br each
signal word. Please read the manual and pay attention to these
symbols.
_DANGER: Indicates an imminently hazardous situation

which, if not avoided, will result in death or serious injury.
iJ,WARNING: Indicates a potentially hazardous situation

which, if not avoided, could result in death or serious injury.
i_CAUTION: Indicates a potentially hazardous situation which,

if not avoided, may result in minor or moderate injury.
NOTICE: Indicates a practice not related to personal injury

which, if not avoided, may result in property damage.

. J

IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR
ANY DEWALT TOOL, CALL US TOLL FREE AT: 1-800-4-DEWALT

(1-800-433-9258}.

_ ARNING: To reduce the risk of injury, read the instruction

manual.

General Power Tool Safety Warnings

_ WARNING! Read all safety warnings and all instructions.

Failure to follow the warnings and instructions may result in
electric shock, fire and/or serious injury,

SAVE ALL WARNINGS AND INSTRUCTIONS

FOR FUTURE REFERENCE

The term "power tool" in the warnings refers to your mains-operated
(corded) power tool or battery-operated (cordless) power tool.

1) WORK AREA SAFETY

a) Keep work area clean and well lit. Cluttered or dark areas

invite accidents.

b) Do not operate power tools in explosive atmospheres,

such as in the presence of flammable liquids, gases or
dust. Power tools create sparks which may ignite the dust or
fumes.

c) Keep children and bystanders away while operating a

power tool. Distractions can cause you to lose control

2) ELECTRICAL SAFETY

a) Power tool plugs must match the outlet. Never modify

the plug in any way. Do not use any adapter plugs with
earthed (grounded) power tools. Unmodified plugs and

matching outlets will reduce risk of electric shock.

b) Avoid body contact with earthed or grounded surfaces

such as pipes, radiators, ranges and refrigerators. There
is an increased risk of electric shock if your body is earthed or

grounded.

c) Do not expose power tools to rain or wet conditions.

Water entering a power tool will increase the risk of electric
shock.

d) Do not abuse the cord. Never use the cord for carrying,

pulling or unplugging the power tool Keep cord away

from heat, oil, sharp edges or moving parts. Damaged or

entangled cords increase the risk of electric shock.

e) When operating a power tool outdoors, use an extension

cord suitable for outdoor use. Use of a cord suitable for
outdoor use reduces the risk of electric shock.

If operating apowertool in a damp location is unavoidable,
use a ground fault circuit interrupter (GFCI) protected

supply. Use of a GFCI reduces the risk of electric shock.

3) PERSONAL SAFETY

a) Stay alert, watch what you are doing and use common

sense when operating a power tool. Do not use a power
tool while you are tired or under the influence of drugs,

alcohol or medication. A moment of inattention while

operating power tools may result in serious personal injury.

b) Use personal protective equipment. Always wear eye

protection. Protective equipment such as dust mask, non-

skid safety shoes, hard hat, or hearing protection used for
appropriate conditions will reduce personal injuries.

c) Prevent unintentional starting. Ensure the switch is in

the off position before connecting to power source and/
or battery pack, picking up or carrying the tool. Carrying

power tools with your finger on the switch or energizing power

tools that have the switch on invites accidents.

d) Remove any adjusting key or wrench before turning the

power tool on. A wrench or a key left attached to a rotating
part of the power tool may result in personal injury.

e) Do not overreach. Keep proper footing and balance at

all times. This enables better control of the power tool in

unexpected situations.

f) Dress properly. Do not wear loose clothing or jewelry.

Keep your hair, clothing and gloves away from moving

parts. Loose clothes, jewelry or long hair can be caught in

moving parts.

g) If devices are provided for the connection of dust

extraction and collection facilities, ensure these are
connected and properly used. Use of dust collection can

reduce dust-related hazards.

4) POWER TOOL USE AND CARE

a) Do not force the power tool Use the correct power tool

for your application. The correct power tool will do the job
better and safer at the rate for which it was designed.

b) Do not use the power tool if the switch does not turn it

on and off. Any power tool that cannot be controlled with the
switch is dangerous and must be repaired.

c) Disconnect the plug from the power source and/or the

battery pack from the power tool before making any
adjustments, changing accessories, or storing power

tools. Such preventive safety measures reduce the risk of
starting the power tool accidentally.

d) Store idle power tools out of the reach of children and do

not allow persons unfamiliar with the power tool or these
instructions to operate the power tool Power tools are

dangerous in the hands of untrained users.

e) Maintain power tools. Check for misalignment or binding

ofmoving parts, breakage ofparts and any other condition
that may affect the power tool's operation. If damaged,

have the power tool repaired before use. Many accidents

are caused by poorly maintained power tools.
Keep cutting tools sharp and clean. Properly maintained

cutting tools with sharp cutting edges are less likely to bind and
are easier to control

g) Use the power tool, accessories and tool bits, etc. in

accordance with these instructions, taking into account
the working conditions and the work to be performed.

Use of the power tool for operations different from those
intended could result in a hazardous situation.

5) BATFERY TOOL USE AND CARE

a) Recharge only with the charger specified by the

manufacturer. A charger that is suitable for one type of
battery pack may create a risk of fire when used with another

battery pack.

b) Use power tools only with specifically designated battery

packs. Use of any other battery packs may create a risk of

injury and fire.

c) When battery pack is not in use, keep H away from other

metal objects like paper clips, coins, keys, nails, screws,

or other small metal objects that can make a connection
from one terminal to another. Shorting the battery terminals

together may cause bums or a fire.

d) Under abusive conditions, liquid may be ejected from

the battery; avoid contact. If contact accidentally occurs,
flush with water. If liquid contacts eyes, additionally seek

medical help. Liquid ejected from the battery may cause

irritation or bums.

6) SERVICE

a) Have your power tool serviced by a qualified repair

person using only identical replacement parts. This will

ensure that the safety of the power tool is maintained.

Safety Instructions for All Saws

a) _DANGER: Keep hands away from cutting area and

the blade. Keep your second hand on auxiliary handle,
or motor housing. If both hands are holding the saw, they

cannot be cut by the blade.

b) Do not reach underneath the workpiece. The guard cannot

protect you from the blade below the workpiece.

c) Adjust the cutting depth to the thickness of the workpiece.

Less than a full tooth of the blade teeth should be visible below
the workpiece.

d) Never hold piece being cut in your hands or across

your leg. Secure the workpiece to a stable platform. /t

is important to support the work properly to minimize body

exposure, blade binding, or loss of control

e) Hold power tool by insulated gripping surfaces when

performing an operation where the cutting tool may

contact hidden wiring. Contact with a "live" wire will also

make exposed metal parts of the power tool "live" and shock
the operator.

When ripping always use a rip fence or straight edge
guide. This improves the accuracy of cut and reduces the

chance of blade binding.

g) Always use blades with correct size and shape (diamond

versus round) of arbor holes. Blades that do not match the
mounting hardware of the saw will run eccentrically, causing
loss of control.

h) Never use damaged or incorrect blade washers or bolt.

The blade washers and bolt were specially designed for your
saw, for optimum performance and safety of operation.

Further Safety Instructions for All Saws

CAUSES AND OPERATOR PREVENTION OF KICKBACK:

- Kickback is a sudden reaction to a pinched, bound or

misaligned saw blade, causing an uncontrolled saw to lift up
and out of the workpiece toward the operator,"

- When the blade is pinched or bound tightly by the kerr closing
down, the blade stalls and the motor reaction drives the unit

rapidly back toward the operator,"

- If the blade becomes twisted or misaligned in the cut, the teeth
at the back edge of the blade can dig into the top surface of the
wood causing the blade to climb out of the kerf and jump back

toward the operator.

Kickback is the result of saw misuse and/or incorrect operating

procedures or conditions and can be avoided by taking proper
precautions as given below."

a) Maintain a firm grip with both hands on the saw and

position your arms to resist kickback forces. Position

your body to either side of the blade, but not in line with

the blade. Kickback could cause the saw to jump backwards,

but kickback forces can be controlled by the operator, if proper

precautions are taken.

b) When blade is binding, or when interrupting a cut for any

reason, release the trigger and hold the saw motionless
in the material until the blade comes to a complete

stop. Never attempt to remove the saw from the work
or pull the saw backward while the blade is in motion or

kickback may occur. Investigate and take corrective actions

to eliminate the cause of blade binding.

c) When restarting a saw in the workpiece, center the

saw blade in the kerf and check that saw teeth are not
engaged into the material. If saw blade is binding, it may

walk up or kickback from the workpiece as the saw is restarted.

d) Support large panels to minimize the risk of blade

pinching and kickback. Large panels tend to sag under their

own weight. Supports must be placed under the panel on both
sides, near the line of cut and near the edge of the panel

e) Do not use dull or damaged blades. Unsharpened or

improperly set blades produce narrow kerf causing excessive
friction, blade binding and kickback.

Blade depth and bevel adjusting locking levers must be
tight and secure before making cut. If blade adjustment

shifts while cutting, it may cause binding and kickback.

g) Use extra caution when making a "plunge cut" into

existing walls or other blind areas. The protruding blade
may cut objects that can cause kickback.

LOWER GUARD SAFETY INSTRUCTIONS

a) Check lower guard for proper closing before each use. Do

not operate the saw if lower guard does not move freely
and close instantly. Never clamp or tie the lower guard

into the open position. If saw is accidentally dropped, lower

guard may be bent. Raise the lower guard with the retracting

handle and make sure it moves freely and does not touch the
blade or any other part, in all angles and depths of cut.

b) Check the operation of the lower guard spring. If the

guard and the spring are not operating properly, they
must be serviced before use. Lower guard may operate

sluggishly due to damaged parts, gummy deposits, or a build-
up of debris.

c) Lower guard should be retracted manually only for

special cuts such as "plunge cuts" and "compound cuts."
Raise lower guard by retracting handle and as soon

as blade enters the material, the lower guard must be
released. For all other sawing, the lower guard should operate

automatically.

d) Always observe that the lower guard is covering the

blade before placing saw down on bench or floor. An
unprotected, coasting blade will cause the saw to walk
backwards, cutting whatever is in its path. Be aware of the time
it takes for the blade to stop after switch is released.

Additional Specific Safety Instructions for

Circular Saws

i_WARNING: Do not use abrasive wheels or blades.
_WARNING: Do not use water feed attachments.

• Use clamps or another practical way to secure and support
the workpiece to a stable platform. Holding the work by hand

or against your body leaves it unstable and may lead to loss of
control.

• Keep your body positioned to either side of the blade, but
not in line with the saw blade. KICKBACK could cause the saw

to jump backwards (see Causes and Operator Prevention of
Kickback and KICKBACK).

• Air vents often cover moving parts and should be avoided.
Loose clothes, jewelry or long hair can be caught in moving parts.

• Avoid cutting nails. Inspect for and remove all nails from lumber
before cutting.

_WARNING: ALWAYS USE SAFETY GLASSES. Everyday
eyeglasses are NOT safety glasses. Also use face or dust mask if

cutting operation is dusty. ALWAYS wear certified safety equipment:

• ANSI Z87.1 eye protection (CAN/CSA Z94.3).

• ANSI $12.6 ($3.19) hearing protection.

• NIOSH/OSHA respiratory protection.

i_WARNING: Some dust created by power sanding, sawing,

grinding, drilling, and other construction activities contains chemicals

known to the State of California to cause cancer, birth defects or
other reproductive harm. Some examples of these chemicals are:

• lead from lead-based paints,

• crystalline silica from bricks and cement and other masonry
products, and

• arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you
do this type of work. To reduce your exposure to these chemicals:

work in a well ventilated area, and work with approved safety
equipment, such as those dust masks that are specially designed to
filter out microscopic particles.

• Avoidprolonged contact with dust from power sanding,

sawing, grinding, drilling, and other construction
activities. Wear protective clothing and wash exposed

areas with soap and water. Allowing dust to get into your

mouth, eyes, or lay on the skin may promote absorption of
harmful chemicals.

_WARNING: Use of this tool can generate and/or disperse dust,
which may cause serious and permanent respiratory or other

injury. Always use NIOSH/OSHA approved respiratory protection
appropriate for the dust exposure. Direct particles away from face

and body. Always operate tool in weft-ventilated area and provide for

proper dust removal. Use dust collection system wherever possible.

_WARNING: ALWAYS wear proper personal hearing protection
that conforms to ANSI $12.6 ($3.19) during use. Under some

conditions and duration of use, noise from this product may
contribute to hearing loss.

_WARNING: ALWAYS use eye protection. All users and
bystanders must wear eye protection that conforms to ANSi Z87. 1.

ACAUTION: When not in use, place circular saw on a stable

surface, shoe side down, where it will not cause a tripping or
falling hazard. Some tools with large battery packs will stand upright

on the battery pack but may be easily knocked over.

• The label on your tool may include the following symbols. The
symbols and their definitions are as follows:

V ................... volts

Hz ................. hertz

min ............... minutes

--- or DC... direct current

(_) ................. Class I Construction

(grounded)

[] ................. Class II Construction

(double insulated)

.../min .......... per minute

BPM ............. beats per minute

IPM ............... impacts per minute

RPM ............. revolutions per

minute

sfpm ............. surface feet

per minute

A...................... amperes

W..................... watts

"_ or AC .......... alternating

current

or AC/DC... alternating

or direct
current

no .................... no load

speed

n...................... rated

speed

..................... earthing

terminal

A ..................... safety alert

symbol

SPM ............. strokes per minute

Important Safety Instructions for All

Battery Packs

When ordering replacement battery packs, be sure to include the
catalog number and voltage. Consult the chart at the end of this
manual for compatibility of chargers and battery packs.

The battery pack is not fully charged out of the carton. Before using
the battery pack and charger, read the safety instructions below and
then follow charging procedures outlined.

READ ALL INSTRUCTIONS

• Do not charge or use the battery pack in explosive

atmospheres, such as in the presence of flammable liquids,
gases or dusL Inserting or removing the battery pack from the

charger may ignite the dust or fumes.

• NEVER force the battery pack into the charger. Do not

modify the battery pack in any way to fit into a non-
compatible charger as battery pack may rupture causing

serious personal injury. Consult the chart at the end of this

manual for compatibility of batteries and chargers.

• Charge the battery packs only in designated DEWALT chargers.

• DO NOT splash or immerse in water or other liquids.

• Do not store or use the tool and battery pack in locations

where the temperature may reach or exceed 105 °F (40 °C)
(such as outside sheds or metal buildings in summer). For

best life store battery packs in a cool, dry location.

NOTE: Do not store the battery packs in a tool with the

trigger switch locked on. Never tape the trigger switch in the
ON position.

i_WARNING: Fire hazard. Never attempt to open the battery pack
for any reason. If the battery pack case is cracked or damaged, do
not insert into the charger. Do not crush, drop or damage the battery

pack. Do not use a battery pack or charger that has received a sharp

blow, been dropped, run over or damaged in any way (e.g., pierced
with a nail, hit with a hammer, stepped on). Damaged battery packs
should be returned to the service center for recycling.

_WARNING: Fire hazard. Do not store or carry the battery

pack so that metal objects can contact exposed battery

terminals. For example, do not place the battery pack in aprons,

pockets, tool boxes, product kit boxes, drawers, etc., with loose

nails, screws, keys, etc. Transporting batteries can possibly

cause fires if the battery terminals inadvertently come in
contact with conductive materials such as keys, coins, hand
tools and the like. The US Department of Transportation Hazardous

Material Regulations (HMR) actually prohibit transporting batteries in
commerce or on airplanes (e.g., packed in suitcases and carry-on
luggage) UNLESS they are properly protected from short circuits.
So when transporting individual battery packs, make sure that the
battery terminals are protected and well insulated from materials that

could contact them and cause a short circuit.

SPECIFIC SAFETY INSTRUCTIONS FOR LITHIUM ION (Li-lon)

• Do not incinerate the battery pack even if it is severely
damaged or is completely worn out. The battery pack can

explode in a fire. Toxic fumes and materials are created when
lithMm ion battery packs are burned.

• If battery contents come into contact with the skin,
immediately wash area with mild soap and water. If battery
liquid gets into the eye, rinse water over the open eye for 15
minutes or until irritation ceases. If medical attention is needed,
the battery electrolyte is composed of a mixture of liquid organic

carbonates and lithium salts.

• Contents of opened battery cells may cause respiratory
irritation. Provide fresh air. If symptoms persist, seek medical
attention.

i_WARNING: Bum hazard. Battery liquid may be flammable if
exposed to spark or flame.

The RBRC TM Seal

The RBRCTM (Rechargeable Battery Recycling
Corporation) Seal on the nickel cadmium, nickel metal
hydride or lithium ion batteries (or battery packs)
indicate that the costs to recycle these batteries (or
battery packs) at the end of their useful life have already
been paid by DEWALT. In some areas, it is illegal to
place spent nickel cadmium, nickel metal hydride or lithium ion
batteries in the trash or municipal solid waste stream and the RBRC
program provides an environmentally conscious alternative.

RBRCTM, in cooperation with DEWALT and other battery users, has
established programs in the United States and Canada to facilitate
the collection of spent nickel cadmium, nickel metal hydride or lithium
ion batteries. Help protect our environment and conserve natural
resources by returning the spent nickel cadmium, nickel metal hydride

or lithium ion batteries to an authorized DEiWALT service center or
to your local retailer for recycling. You may also contact your local

recycling center for information on where to drop off the spent battery.
RBRC TM is a registered trademark of the Rechargeable Battery

Recycling Corporation.

Important Safety Instructions for All
Battery Chargers

SAVE THESE INSTRUCTIONS: This manual contains important

safety and operating instructions for battery chargers.

• Before using the charger, read all instructions and cautionary
markings on the charger, battery pack and product using the
battery pack.

A WARNING: Shock hazard. Do not allow any liquid to get inside the
charger. Electric shock may result.

ACAUTION: Bum hazard. To reduce the risk of injury, charge only
DEWALT rechargeable battery packs. Other types of batteries may
overheat and burst resulting in personal injury and property damage.

NOTICE: Under certain conditions, with the charger plugged into the

power supply, the charger can be shorted by foreign material Foreign

materials of a conductive nature, such as, but not limited to, grinding
dust, metal chips, steel wool, aluminum foil or any buildup of metallic

particles should be kept away from the charger cavities. Always unplug

the charger from the power supply when there is no battery pack in the
cavity, Unplug the charger before attempting to clean.

• DO NOT attempt to charge the battery pack with any
chargers other than the ones in this manual The charger and

battery pack are specifically designed to work together.

• These chargers are not intended for any uses other than
charging DEWALT rechargeable batteries. Any other uses may

result in risk of fire, electric shock or electrocution.

• Do not expose the charger to rain or snow.

• Pull by the plug rather than the cord when disconnecting
the charger. This will reduce the risk of damage to the electric plug
and cord.

• Make sure that the cord is located so that it will not be

stepped on, tripped over or otherwise subjected to damage
or stress.

• Do not use an extension cord unless it is absolutely
necessary. Use of improper extension cord could result in risk of

fire, electric shock or electrocution.

• When operating a charger outdoors, always provide a dry

location and use an extension cord suitable for outdoor use.

Use of a cord suitable for outdoor use reduces the risk of electric
shock.

An extension cord must have adequate wire size (AWG

or American Wire Gauge) for safety. The smaller the gauge

number of the wire, the greater the capacity of the cable, that is,

16 gauge has more capacity than 18 gauge. An undersized cord

will cause a drop in line voltage resulting in loss of power and
overheating. When using more than one extension to make up the

total length, be sure each individual extension contains at least the
minimum wire size. The following table shows the correct size to

use depending on cord length and nameplate ampere rating. If in
doubt, use the next heavier gauge. The lower the gauge number,

the heavier the cord.

Minimum Gauge for Cord Sets

Ampere

Rating

More Not
Than More

Than

0 6 18 16 16 14

6 10 18 16 14 12

10 12 16 16 14 12
12 16 14 12 Not Recommended

• Do not place any object on top of the charger or place the

charger on a soft surface that might block the ventilation

slots and result in excessive internal heat. Place the charger
in a position away from any heat source. The charger is ventilated
through slots in the top and the bottom of the housing.

• Do not operate the charger with a damaged cord or plug.

• Do not operate the charger if it has received a sharp blow,
been dropped or otherwise damaged in any way. Takeit to an

authorized service center.

Volts Total Length of Cord in Feet (meters)

120V 25 (7.6) 50 (15.2) 100 (30.5) 150 (45.7)
240V 50 (15.2) 100 (30.5) 200 (61.0) 300 (91.4)

AWG

• Do not disassemble the charger; take it to an authorized
service center when service or repair is required. Incorrect

reassembly may result in a risk of electric shock, electrocution
or fire.

• Disconnect the charger from the outlet before attempting

any cleaning. This will reduce the risk of electric shock.

Removing the battery pack will not reduce this risk.

• NEVER attempt to connect 2 chargers together.

• The charger is designed to operate on standard 120V

household electrical power. Do not attempt to use it on any
other voltage. This does not apply to the vehicular charger.

Chargers

Your tool uses a DEWALTcharger. Be sure to read all safe,/instructions
before using your charger. Consult the chart at the end of this manual
for compatibility of chargers and battery packs.

Charging Procedure (Fig. 1)

1. Plug the charger into an FIG.1 C
appropriate outlet before inserting

the battery pack.

2. Insert the battery pack (C)
into the charger, as shown in
Figure 1, making sure the pack

is fully seated in charger. The
red (charging) light will blink
continuously, indicating that the

charging process has started.

3. The completion of charge will
be indicated by the red light

remaining ON continuously. The pack is fully charged and may be
used at this time or left in the charger.

Indicator Light Operation

_] PACKCHARGING

PACKCHARGED

)-=HOT/COLDDELAY--e --e --e --o _e

PROBLEMPACKORCHARGERe • • • • o • • • •

PROBLEMPOWERLINEee ee ee ee ee

Charge Indicators

This charger is designed to detect certain problems that can arise.
Problems are indicated by the red light flashing at a fast rate. If this
occurs, re-insert the battery pack into the charger. If the problem
persists, try a different battery pack to determine if the charger is
working properly. If the new pack charges correctly, then the original
pack is defective and should be returned to a service center or other
collection site for recycling. If the new battery pack elicits the same
trouble indication as the original, have the charger and the battery pack

tested at an authorized service center.

HOT/COLD DELAY

This charger has a hot/cold delay feature: when the charger detects a
battery that is hot, it automatically starts a delay, suspending charging
until the battery has cooled. After the battery has cooled, the charger
automatically switches to the pack charging mode. This feature
ensures maximum battery life. The red light flashes long, then short
while in the hot/cold delay mode.

LEAVING THE BATTERY PACK IN THE CHARGER

The charger and battery pack can be left connected with the charge
indicator showing Pack Charged.

WEAK BA'R'ERY PACKS: Weak batteries will continue to function
but should not be expected to perform as much work.

FAULTY BATTERY PACKS: This charger will not charge a faulty
battery pack. The charger will indicate faulty battery pack by refusing
to light or by displaying problem pack or charger.

NOTE: This could also mean a problem with a charger.
PROBLEM POWER LINE

Some chargers have a problem powerline indicator.When the charger
is used with some portable power sources such as generators or
sources that convert DC to AC, the charger may temporarily suspend
operation, flashing the red light with two fast blinks followed by a pause.
This indicates the power source is out of limits.

Important Charging Notes

1. Longest life and best performance can be obtained if the battery
pack is charged when the air temperature is between 65 °F and
75 °F (18 °-24 °C). DO NOT charge the battery pack in an air
temperature below +40 °F (+4.5 °C), or above +105 °F (+40.5 °C).
This is important and will prevent serious damage to the battery
pack.

2. The charger and battery pack may become warm to the touch
while charging. This is a normal condition, and does not indicate
a problem. To facilitate the cooling of the battery pack after use,
avoid placing the charger or battery pack in a warm environment

such as in a metal shed or an uninsulated trailer.

3.Acoldbatterypackwillchargeatabouthalftherateofawarm
batterypack.Thebatterypackwillchargeatthatslowerrate
throughouttheentirechargingcycleandwillnot returnto
maximumchargerateevenifthebatterypackwarms.

4.Ifthebatterypackdoesnotchargeproperly:
a.Checkoperationofreceptaclebyplugginginalamporother

appliance;

b.Checktoseeifreceptacleisconnectedtoalightswitchwhich

turnspoweroffwhenyouturnoutthelights;

c.Movethechargerandbatterypacktoa locationwherethe

surroundingairtemperatureis approximately65 °F-75°F
(18°-24°C);

d.Ifchargingproblemspersist,takethetool,batterypackand

chargertoyourlocalservicecenter.

5.Thebatterypackshouldberechargedwhenitfailstoproduce
sufficientpoweronjobswhichwereeasilydonepreviously.DO

NOTCONTINUEto useundertheseconditions.Followthe
chargingprocedure.Youmayalsochargeapartiallyusedpack

wheneveryoudesirewithnoadverseeffectonthebatterypack.

6.Foreignmaterialsofaconductivenaturesuchas,butnotlimited
to,grindingdust,metalchips,steelwool,aluminumfoil,orany
buildupofmetallicparticlesshouldbekeptawayfromcharger
cavities.Alwaysunplugthechargerfromthepowersupplywhen
thereisnobatterypackinthecavity.Unplugthechargerbefore
attemptingtoclean.

7.Donotfreezeorimmersethechargerinwateroranyotherliquid.

AWARNING: Shock hazard. Don't allow any liquid to get inside the

charger. Electric shock may result.
i_WARNING: Bum hazard. Do not submerge the battery pack in

any liquid or allow any liquid to enter the battery pack. Never attempt
to open the battery pack for any reason. If the plastic housing of the

battery pack breaks or cracks, return to a service center for recycling.

Storage Recommendations

1. The best storage place is one that iscool and dry, away from direct
sunlight and excess heat or cold.

2. For long storage, it is recommended to store a fully charged
battery pack in a cool dry place out of the charger for optimal

results.

NOTE" Battery packs should not be stored completely depleted of
charge. The battery pack will need to be recharged before use.

SAVE THESE INSTRUCTIONS FOR

FUTURE USE

COMPONENTS

_ WARNING: Never modify the power tool or any part of it. Damage
or personal injury could result.

Please refer to the front of this section for the list of components.

INTENDED USE

This heavy-duty circular saw is designed for professional wood cutting
applications.

DO NOT use under wet conditions or in presence of flammable liquids
or gases.

DO NOT let children come into contact with the tool. Supervision is
required when inexperienced operators use this tool.

OPERATION

_WARNING: To reduce the risk of serious personal injury,
turn tool off and disconnect tool from power source before
making any adjustments or removing/installing attachments or
accessories. An accidental start-up can cause injury.

10

Installing and Removing the Battery Pack
(Fig. 2)

NOTE: For best results, make sure your battery pack is fully charged.
To install the battery pack (C) into the tool handle, align the battery

pack with the rails inside the tool's handle and slide it into the handle
until the battery pack is firmly seated in the tool and ensure that it does
not disengage.

Toremove the battery pack from the tool, press the release button (M)
and firmly pull the battery pack out of the tool handle. Insert it into the
charger as described in the charger section of this manual.

M

FIG. 2

FUEL GAUGE BA'rI'ER¥ PACKS (FIG. 2A)
Some DEWALT battery packs include a fuel gauge which consists of

three green LED lights that indicate the level of charge remaining in
the battery pack.

To actuate the fuel gauge, press and hold the fuel gauge button (R).

C

FIG. 2A

A combination of the three green LED lights will illuminate designating
the level of charge left. When the level of charge in the battery is below
the usable limit, the fuel gauge will not illuminate and the battery will
need to be recharged.

NOTE: The fuel gauge is only an indication of the charge left on the
battery pack. It does not indicate tool functionality and is subject to
variation based on product components, temperature and end-user
application.

For more information regarding fuel gauge battery packs, please call
1-800-4-DEWALT (1-800-433-9258) or visit our website www.dewalt.

com.

Trigger Switch (Fig. 3)

i_WARNING: This tool has no

provision to lock the trigger switch FIG.3 A

in the ON position and should B
never be locked ON by any other

means.

Release the trigger switch lock-off
button (A)by pressing the button as

shown. Pull the trigger switch (B)
to turn the motor on. Releasing the

trigger switch turns the motor off.

Changing Blades (Fig. 4, 5)

TO INSTALL THE BLADE (FIG. 4, 5)

1. Place inner clamp washer (O) on saw spindle with the large flat
surface facing out toward the blade (Fig.4A, 4B).

2. Retract the lower blade guard (G) and place blade on saw spindle
against the inner clamp washer, making sure that the blade
will rotate in the proper direction (the direction of the rotation
arrow on the saw blade and the teeth must point in the same

11

direction as the direction of rotation arrow on the lower blade
guard). Do not assume that the printing on the blade will always

be facing you when properly installed. When retracting the lower
blade guard to install the blade, check the condition and operation
of the lower blade guard to assure that it is working properly. Make
sure it moves freely and does not touch the blade or any other
part, in all angles and depths of cut.

FIG. 4A [

K

3. Place outer clamp washer (P) on saw spindle with the large flat
surface against the blade with beveled side facing out.

4. Thread blade clamping screw (H)into saw spindle by hand (screw
has left-hand threads and must be turned counterclockwise to

tighten).

5. Depress the blade lock button (K) while turning the saw spindle
with the blade wrench (N) until the blade lock engages and the

blade stops rotating (Fig. 5).

6. Tighten the blade clamping screw firmly with the blade wrench.

NOTE" Never engage the blade lock while saw is running, or engage
in an effort to stop the tool. Never turn the saw on while the blade lock
is engaged. Serious damage to your saw will result.

FIG. 4B

SPINDLE

BLADE

12

TO REPLACE THE BLADE (FIG. 4, 5}

1. To loosen the blade clamping screw (H), depress the blade lock
button (K)and turn the saw spindle with the blade wrench (N) until

the blade lock engages and the blade stops rotating. With the
blade lock engaged, turn the blade clamping screw clockwise with

the blade wrench (screw has left-hand threads and must be turned
clockwise to loosen).

FIG. 5

LOOSE[',

(clockwise)

TIGHTEN

(countemtockwise)

2. Remove the blade clamping screw (H)and outer clamp washer (P)
only. Remove old blade.

3. Clean any sawdust that may have accumulated in the guard or
clamp washer area and check the condition and operation of the

lower blade guard as previously outlined. Do not lubricate this area.

4. Select the proper blade for the application (see Blades). Always
use blades that are the correct size (diameter) with the proper size

and shape center hole for mounting on the saw spindle. Always
assure that the maximum recommended speed (rpm) on the saw

blade meets or exceeds the speed (rpm) of the saw.

5. Follow steps 2 through 6 under To Install the Blade, making sure
that the blade will rotate in the proper direction.

LOWER BLADE GUARD

_WARNING: The lower blade guard is a safety feature which
reduces the risk of serious personal injury. Never use the saw
if the lower blade guard is missing, damaged, misassembled

or not working properly. Do not rely on the lower blade
guard to protect you under all circumstances. Your safety
depends on following all warnings and precautions as well

as proper operation of the saw. Check lower blade guard for

proper closing before each use as outlined in Further Safety

Instructions for All Saws. If the lower blade guard is missing

or not working properly, have the saw serviced before using.
To assure product safety and reliability, repair, maintenance

and adjustment should be performed by an authorized service
center or other qualified service organization, always using

identical replacement parts.

Blades

AWARNING: To minimize the risk of eye injury, always use eye

protection. Carbide is a hard but brittle material Foreign objects in

the workpiece such as wire or nails can cause tips to crack or break.
Only operate saw when proper saw blade guard is in place. Mount

blade securely in proper rotation before using, and always use a
clean, sharp blade.
AWARNING: Do not cut ferrous metals (steel), masonry, glass,
masonry-type planking, cement board or tile with this saw.

Do not use abrasive wheels or blades. A dull blade will cause slow
inefficient cutting, overload on the saw motor, excessive splintering,

and could increase the possibility of kickback. Please refer to the
table below to determine the correct size replacement blade for your

model saw.

13

Blade Diameter Teeth Application

DW9155 6-1/2" (165 mm) 18 General purpose cutting
DW9154 6-1/2" (165 mm) 24 Smooth wood cutting
DW9153 6-1/2" (165 mm) 90 Non-carbide, plywood/

vinyl siding cutting

Ifyou need assistance regarding blades, please call 1-800-4-DEWALT
(1-800-433-9258).

KICKBACK

Kickback is a sudden reaction to a pinched, bound or misaligned saw
blade, causing an uncontrolled saw to lift up and out of the workpiece

toward the operator. When the blade is pinched or bound tightly by the
kerf closing down, the blade stalls and the motor reaction drives the
unit rapidly back toward the operator. If the blade becomes twisted or

misaligned in the cut, the teeth at the back edge of the blade can dig
into the top surface of the wood causing the blade to climb out of the

kerf and jump back toward the operator.
Kickback is more likely to occur when any of the following conditions

exists.

1. IMPROPER WORKPIECE SUPPORT

A. Sagging or improper lifting of the cut off piece can cause

pinching of the blade and lead to kickback (Fig. 12).

B. Cutting through material supported at the outer ends only can

cause kickback. As the material weakens it sags, closing down
the kerf and pinching the blade (Fig. 12).

C. Cutting off a cantilevered or overhanging piece of material from

the bottom up in a vertical direction can cause kickback. The
falling cut off piece can pinch the blade.

D. Cutting off long narrow strips (as in ripping) can cause kickback.

The cut off strip can sag or twist closing the kerf and pinching

the blade.

E. Snagging the lower guard on a surface below the material being

cut momentarily reduces operator control. The saw can lift
partially out of the cut increasing the chance of blade twist.

2. IMPROPER DEPTH OF CUT SETTING ON SAW

To make the most efficient cut, the blade should protrude only far
enough to expose one-half of a tooth as shown in Figure 7. This

allows the shoe to support the blade and minimizes twisting and
pinching in the material. See the section titled Cutting Depth

Adjustment.

3. BLADE TWISTING (MISALIGNMENT IN CUT)

A. Pushing harder to cut through a knot, a nail, or a hard grain area

can cause the blade to twist.

B.Trying to turn the saw in the cut (trying to get back on the

marked line) can cause blade twist.

C. Overreaching or operating the saw with poor body control (out

of balance), can result in twisting the blade.

D. Changing hand grip or body position while cutting can result in

blade twist.

E. Backing up the saw to clear blade can lead to twist.

4. MATERIALS THAT REQUIRE EXTRA ATTENTION

A.Wet lumber
B. Green lumber (material freshly cut or not kiln dried)

C. Pressure treated lumber (material treated with preservatives or

anti-rot chemicals)

5. USE OF DULL OR DIRTY BLADES

Dull blades cause increased loading of the saw. To compensate,
an operator will usually push harder which further loads the unit

and promotes twisting of the blade in the kerf. Worn blades may
also have insufficient body clearance which increases the chance

of binding and increased loading.

14

6. LIFTING THE SAW WHEN MAKING A BEVEL CUT

Bevel cuts require special operator attention to proper cutting
techniques - especially guidance of the saw. Both blade angle to

the shoe and greater blade surface in the material increase the
chance for binding and misalignment (twist) to occur.

7. RESTARTING A CUT WITH THE BLADE TEETH JAMMED
AGAINST THE MATERIAL

The saw should be brought up to full operating speed before
starting a cut or restarting a cut after the unit has been stopped

with the blade in the kerf. Failure to do so can cause stalling and
kickback.

Any other conditions which could result in pinching, binding, twisting,
or misalignment of the blade could cause kickback. Refer to the
sections Further Safety Instructions for All Saws and Blades
for procedures and techniques that will minimize the occurrence of

kickback.

Cutting Depth Adjustment (Fig. 6, 7)

1. Hold the saw firmly and loosen (clockwise) the depth adjustment
knob (D)and move shoe to obtain the desired depth of cut.

2. Make sure the depth adjustment knob has been retightened
(counterclockwise) before operating saw.

FIG.6 FIG.7

For the most efficient cutting action, set the depth adjustment so that
one-half tooth of the blade will project below the material to be cut.

This distance is from the tip of the tooth to the bottom of the gullet in
front of it. This keeps blade friction at a minimum, removes sawdust

from the cut, results in cooler, faster sawing and reduces the chance
of kickback. A method for checking for correct cutting depth is shown
in Figure 7. Lay a piece of the material you plan to cut along the side

of the blade, as shown, and observe how much tooth projects beyond
the material.

Bevel Angle Adjustment (Fig. 7)

The full range of the bevel adjustment is from 0°to 50°. The quadrant is
graduated in increments of 1o. On the front of the saw is a bevel angle
adjustment mechanism consisting of a calibrated quadrant and a bevel
adjustment knob (J).

TO SET THE SAW FOR A BEVEL CUT

1. Loosen (counterclockwise) the bevel adjustment knob (J) and tilt
shoe to the desired angle by aligning the pointer with the desired
angle mark.

2. Retighten knob firmly (clockwise).

Shoe Adjustment for 90°Cuts (Fig. 8)

IF ADDITIONAL ADJUSTMENT IS NEEDED: FIG.8

1. Adjust the saw to 0° bevel.

2. Retract the lower blade guard. Place the
saw on blade side.

3. Loosen bevel adjustment knob (J). Place a
square against the blade and shoe to adjust
the 90° setting.

4. Turn the calibration screw (Q) so that the
shoe will stop at the proper angle.

Q

15

5. Confirm the accuracy of the setting by checking the squareness of
an actual cut on a scrap piece of material.

Kerf Indicator (Fig. 9)

The front of the saw shoe has a kerf indicator (I)
for vertical and bevel cutting. This indicator
enables you to guide the saw along cutting
lines penciled on the material being cut. The
kerf indicator lines up with the left (outer) side of
the saw blade, which makes the slot or "kerf"
cut by the moving blade fall to the right of the
indicator. Guide along the penciled cutting line
so that the kerf falls into the waste or surplus

material.

Workpiece Support (Fig. 10-12)

WARNING: It is important to support the work properly and to

hold the saw firmly to prevent loss of control which could cause

personal injury. Figure 10 illustrates proper hand support of the saw.

Maintain a firm grip with both hands on the saw and position your
body and arm to allow you to resist kickback if it occurs. ALWAYS

TURN OFF TOOL AND REMOVE BATTERY BEFORE MAKING ANY

ADJUSTMENTS!

FIG.10

FIG. 9

I

Figure 10 shows proper sawing position. Note that hands are kept away
from cutting area. To avoid kickback, DO support board or panel
NEAR the cut (Fig. 11). DON'T support board or panel away from the
cut (Fig. 12).

Place the work with its "good" side - the one on which appearance is
most important - down. The saw cuts upward, so any splintering will

be on the work face that is up when you cut it.

FIG.11 DOsupportboard or panelNEARthe cut.

SUPPORT

FIG. 12

DON'T support board or panel AWAY from the cut.

Cutting (Fig. 10)

Place the wider portion of the saw shoe on that part of the workpiece
which is solidly supported, not on the section that will fall off when the

cut is made. As an example, Figure 10 illustrates the RIGHT way to
cut off the end of a board. Always clamp work. Don't try to hold short

16

pieces by hand! Remember to support cantilevered and overhanging
material. Use caution when sawing material from below.
Be sure saw is up to full speed before blade contacts materialto be cut.
Starting saw with blade against material to be cut or pushed forward

into kerf can result in kickback. Push the saw forward at a speed which
allows the blade to cut without laboring.

Hardness and toughness can vary even in the same piece of material,
and knotty or damp sections can put a heavy load on the saw. When

this happens, push the saw more slowly, but hard enough to keep
working without much decrease in speed. Forcing the saw can cause

rough cuts, inaccuracy, kickback, and over-heating of the motor.
Should your cut begin to go off the line, don't try to force it back on.

Release the trigger switch and allow blade to come to a complete stop.
Then you can withdraw the saw, sight anew, and start a new cut slightly

inside the wrong one. Withdraw the saw if you must shift the cut. Forcing
a correction inside the cut can stall the saw and lead to kickback.

IF SAW STALLS, RELEASE THE TRIGGER SWITCH AND BACK THE
SAW UNTIL IT IS LOOSE. BE SURE BLADE IS STRAIGHT IN THE

CUT AND CLEAR OF THE CUTTING EDGE BEFORE RESTARTING.
As you finish a cut, release the trigger switch and allow the blade

to stop before lifting the saw from the work. As you lift the saw, the
spring-tensioned lower blade guard will automatically close under the

blade. Remember the blade is exposed until this occurs. Never reach
under the work for any reason. When you have to retract the lower

blade guard manually (as is necessary for starting pocket cuts), always
use the retracting lever.
_WARNING: When cutting thin strips, be careful to ensure that

small cutoff pieces don't hang up on the inside of the lower blade

guard.

RIPPING (FIG. 13)
Ripping is the process of cutting wider boards into narrower strips -

cutting grain lengthwise. Hand guiding is more difficult for this type of
sawing and the use of a DEWALT rip fence is recommended.

FIG. 13

INSTALLRIPFENCE

INTHIS DIRECTION

POCKET CUTTING (FIG. 14) FIG.14
_WARNING: Never tie the

lower blade guard in a raised
position. Never move the saw
backwards when pocket cutting.

Thismay cause the saw to raise

up off the work surface, which
could cause inju_

A pocket cut is one that is
made in a floor, wall or other
flat surface.

1. Adjust the saw shoe so
the blade cuts at desired

depth.

2. Tilt the saw forward and rest front of the shoe on material to be cut.

3. Using the lower blade guard retracting lever, retract the lower
blade guard to an upward position. Lower the rear of the shoe until

the blade teeth almost touch the cutting line.

4. Release the lower blade guard (its contact with the work will keep
it in position to open freely as you start the cut). Remove your
hand from the lower blade guard retracting lever and firmly grip

the auxiliary handle, as shown in Figure 14. Position your body and
arm to allow you to resist kickback if it occurs.

17

5. Make sure blade is not in contact with cutting surface before
starting saw.

6. Start the motor and gradually lower the saw until its shoe rests flat
on the material to be cut. Advance saw along the cutting line until

cut is completed.

7. Release the trigger switch and allow the blade to stop completely
before withdrawing the blade from the material.

8. When starting each new cut, repeat the above steps.

MAINTENANCE

_WARNING: To reduce the risk of serious personal injury,
turn tool off and disconnect tool from power source before

making any adjustments or removing/installing attachments or
accessories. An accidental start-up can cause injury.

Cleaning

J_WARNING: Blow dirt and dust out of all air vents with clean, dry air

at least once a week. To minimize the risk of eye injury, always wear

ANSI Z87.1 approved eye protection when performing this.

AWARNING: Never use solvents or other harsh chemicals for
cleaning the non-metallic parts of the tool These chemicals may

weaken the plastic materials used in these parts. Use a cloth
dampened only with water and mild soap. Never let any liquid get

inside the tool,"never immerse any part of the tool into a liquid.

CHARGER CLEANING INSTRUCTIONS

_WARNING: Shock hazard. Disconnect the charger from the AC
outlet before cleaning. Dirt and grease may be removed from the

exterior of the charger using a cloth or soft non-metallic brush. Do not
use water or any cleaning solutions.

Lubrication

Self lubricating ball and roller bearings are used in the tool and
relubrication is not required. However, it is recommended that, once

a year, you take or send the tool to a certified service center for a
thorough cleaning, inspection, and lubrication of the gear case.

Accessories

AWARNING: Since accessories, other than those offered by
DEWALT, have not been tested with this product, use of such

accessories with this tool could be hazardous. To reduce the risk of
injury, only DEWALT recommended accessories should be used with

this product.

Recommended accessories for use with your tool are available at
extra cost from your local service center. If you need any assistance
in locating any accessory, please contact DEWALT Industrial Tool Co.,

701 East Joppa Road, Baltimore, MD 21286, call 1-800-4-DEWALT
(1-800-433-9258) or visit our website: www.dewalt.com.

Repairs

The charger and battery pack are not serviceable. There are no
serviceable parts inside the charger or battery pack.

To assure product SAFETY and RELIABILITY, repairs, maintenance
and adjustments (including brush inspection and replacement) should
be performed by a DEWALT factory service center, a DEWALT
authorized service center or other qualified service personnel. Always
use identical replacement parts.

Register Online

Thank you for your purchase. Register your product now for:

• WARRANTY SERVICE: Registering your product will help you
obtain more efficient warranty service in case there is a problem
with your product.

• CONFIRMATION OF OWNERSHIP" In case of an insurance
loss, such as fire, flood or theft, your registration of ownership will

serve as your proof of purchase.

18

• FOR YOUR SAFETY: Registering your product will allow us to
contact you in the unlikely event a safety notification is required
under the Federal Consumer Safety Act.

Register online at www.dewalt.com/register.

Three Year Limited Warranty

DEWALTwill repair, without charge, any defects due to faulty materials
or workmanship for three years from the date of purchase. This
warranty does not cover part failure due to normal wear or tool abuse.
For further detail of warranty coverage and warranty repair information,
visit www.dewalt.com or call 1-800-4-DEWALT (1-800-433-9258).
This warranty does not apply to accessories or damage caused where
repairs have been made or attempted by others. This warranty gives
you specific legal rights and you may have other rights which vary in
certain states or provinces.

In addition to the warranty, DEWALT tools are covered by our:

1 YEAR FREE SERVICE

DEWALT will maintain the tool and replace worn parts caused by
normal use, for free, any time during the first year after purchase.

2 YEARS FREE SERVICE ON DEWALT BA'rrERY PACKS

DC9071, DC9091, DC9096, DC9280, DC9360, DC9180, DCB120,

DCB127, DCB201, DCB203 and DCB207.

3 YEARS FREE SERVICE ON DEWALT BA'rrERY PACKS

DCB200, DCB204, DCB205

DEWALT BATTERY PACKS

Product warranty voided if the battery pack is tampered with in any
way. DEWALT is not responsible for any injury caused by tampering
and may prosecute warranty fraud to the fullest extent permitted by

law.

90 DAY MONEY BACK GUARANTEE

If you are not completely satisfied with the performance of your
DFWALT Power Tool, Laser, or Nailer for any reason, you can return it
within 90 days from the date of purchase with a receipt for a full refund

- no questions asked.
LATIN AMERICA: This warranty does not apply to products sold

in Latin America. For products sold in Latin America, see country
specific warranty information contained in the packaging, call the local
company or see website for warranty information.
FREE WARNING LABEL REPLACEMENT:

If your warning labels become illegible or are missing, call
1-800-4-DEWALT (1-800-433-9258) for a free replacement.

DCSXXX61/2"(165mmlC0nDLESSCl.CU_RSAW

SER.

KEEP HANDS AND 0ODY

0F THE BLADE, CONTACT WITH BLADE WiLL RESULT JN SERIOUS JN3UHY.

MANTENGA LAS MANOS Y EL CUERPU ALEJAOOS DE LA HOJA Y A UN lAD0
DE LAMMMA, EL CONTACTO CON LA HOJA PR0VOCA LESIONES GRAVES.

TENiR LES MAINS ET TOUTE AUTHE PAHTIE Og CORPS ELOIGNEES DE LA LAME
ET RHR LEC()T_ OE CELLE-CL TOUT CONTACT AVEC LA LAME RISQUE DE CAUSER

DE GRAVES BLESSURES.

TOREOGCETHEHIRK0PIMJUHY,USEHMUST HEA0INRTHUCTIONMANUAL

CHECK GUAR01NG SYSTEM. IT MUST COVED BLADE INSTANTLY_ HOLD SAW
WITH DOTH HANDS, SUPP00T AND CLAMP W00K. WEAR EYE PROTECTJ0N.

ALWAYS USE PROPER HERPJHATOHY PROTECTION. USE WITH OEWALT BATfEHY.
REMOVE 8ATfEOY PACO WHEN CHANGING BLADES OR MAKING ADJUSTMENTS.

PARA DJSMJNGJR EL HJESGODE LESJONES, EL USUAHJO DEDEHA LEER EL
MANUAL DE INSTHUCCBONES. BNSPECCBONE LA GOAHDA JNFEM00. LA

GGAROA DEOE DE CEDHAR iNSTANT/_.N EAMENTE_ SOSTEN GA LA SIERRA CON
AMBAS MANOS. QUITE EL PAQUETE DE LA DATEHIA AL CAMDJAH LAS
LAMINAS OHACMNOO AJHSTES.

A T|TRE PRi!VENT|F. LME LE GUIDE. V_HIFiED LE PROTECTEUH INF_01EUR. CE
OERNIEH D01T SE REFEHMER INS'_ANTANEMENT. TENIR LA SCiE DES OEUX
MAINS. SGUTENiR ET FIXER LA PIECE A 0UVOER. ENI_VEZ LE PAQUET DE

DATTERM EN CHANGEANT DES LAMES GU EN FAISANT DES AJGSTEMENTS.
DEWALT iNDUSTRiAL TOOL CO., HALTIMORE, MD 21286 USA

F0H SEOVICE iNFORMATION CALL: 1-M6-C-OEWALT www.DEWALT,co_n

AWAY FROM AND TO THE SIDE

19

Scies circulaires sans fil de 20 V max* et 5 250 tr/min, modules DCS391, DCS393

L

K

A

B A

\

A. BOUTON DE VERROUILLAGE DE LA GACHETrE

B. INTERRUPTEUR _, GACHETrE

C. BLOC-PILES
D. BOUTON DE RI_GLAGE DE LA PROFONDEUR

E. PATIN

F. LEVIER RI_TRACTANT DU PROTEGE-LAME INFt_RIEUR

G. PROTEGE-LAME INFI_RIEUR

M

H. VIS DE FIXATION DE LA LAME

I. INDICATEUR DE TRAIT DE SCIE

J. BOUTON DE RI-GLAGE D'ANGLE DE BISEAU

K. BOUTON DE VERROUILLAGE DE LA LAME (non illustre)

L. POIGNEE AUXILIAIRE

M. BOUTON DE LIBt_RATION DU BLOC-PILES

N. CLI_ POUR LAME

2O