DeWalt DCD791, DCD796 Original Instructions Manual

Download

Page 1

Final page size: A5 (148mm x 210mm)

DCD791 DCD796

Page 2

DeWALT

English (original instructions) 3

Page 3

Fig. A

DCD796

Fig. B

1011

Page 4

Fig. C

Fig. D

Fig. G Fig. H Fig. I

Fig. E Fig. F

Page 5

BRUSHLESS CORDLESS COMPACT 13 mm

DeWALT

DRILL/DRIVER, DCD791 BRUSHLESS CORDLESS COMPACT 13 mm DRILL/DRIVER/HAMMERDRILL, DCD796

ENGLISH

Congratulations!

You have chosen a product development and innovation make most reliable partners for professional power toolusers.

tool. Years of experience, thorough

one of the

Technical Data

DCD791 DCD796 Voltage Type Battery type Power output No-load speed

1st gear min-10–550 0–550 2nd gear min-10–2000 0–2000

Impact rate

1st gear min-1— 0–9,350

2nd gear min-1— 0–34,000 Max. torque (hard/soft) Nm 70/27 70/27 Chuck capacity mm 1.5–13.0 1.5–13.0 Maximum drilling capacity

Wood mm 40 40

Metal mm 13 13

Masonry mm — 13 Weight (without battery pack) kg

Noise values and vibration values (triax vector sum) according to EN60745-2-1:

LPA (emission sound pressure level) dB(A)

LWA (sound power level) dB(A)

K (uncertainty for the given sound level) dB(A)

Drilling into metal

Vibration emission value a Uncertainty K = m/s21.5 1.5

Drilling into concrete

Vibration emission value a Uncertainty K = m/s2— 1.6

Screwdriving

Vibration emission value a Uncertainty K = m/s21.5 1.5

The vibration emission level given in this information sheet has been measured in accordance with a standardised test given in EN60745 and may be used to compare one tool with another. It may be used for a preliminary assessment ofexposure.

= m/s2<2.5 <2.5

h,D

= m/s2— 11.5

h,ID

= m/s2<2.5 <2.5

h,D

18 18

1/10 1/10

Li-Ion Li-Ion

W 460 460

1.1 1.2

76 89 87 100

3 3

WARNING: The declared vibration emission level represents the main applications of the tool. However if



the tool is used for different applications, with different accessories or poorly maintained, the vibration emission may differ. This may significantly increase the exposure level over the total workingperiod.

An estimation of the level of exposure to vibration should also take into account the times when the tool is switched off or when it is running but not actually doing the job. This may significantly reduce the exposure level over the total workingperiod.

Identify additional safety measures to protect the operator from the effects of vibration such as: maintain the tool and the accessories, keep the hands warm, organisation of workpatterns.

EC-Declaration of Conformity

Machinery Directive

Brushless Cordless Compact Drill Driver/ Hammerdrill DCD791, DCD796

declares that these products described under

Technical Data are in compliance with: 2006/42/EC, EN60745-1:2009+A11:2010, EN60745-2-1:2010, EN60745-2-2:2010.

These products also comply with Directive 2014/30/EU and 2011/65/EU. For more information, please contact the following address or refer to the back of themanual.

The undersigned is responsible for compilation of the technical file and makes this declaration on behalf of

Markus Rompel Director Engineering

, Richard-Klinger-Straße 11,

D-65510, Idstein, Germany

22.06.2017

WARNING: To reduce the risk of injury, read the instructionmanual.

Page 6

Weight

ENGLISH

Batteries Chargers/Charge Times (Minutes)

Cat # V

DCB546 18/54 6.0/2.0 1.05 270 140 90 60 90 X DCB547 18/54 9.0/3.0 1.25 420 220 140 85 140 X DCB181 18 1.5 0.35 70 35 22 22 22 45

DCB182 18 4.0 0.61 185 100 60 60 60 120 DCB183/B 18 2.0 0.40 90 50 30 30 30 60 DCB184/B 18 5.0 0.62 240 120 75 75 75 150

DCB185 18 1.3 0.35 60 30 22 22 22 X

DCB187 18 3.0 0.48 140 70 45 45 45 90

Ah Weight (kg) DCB107 DCB113 DCB115 DCB118 DCB132 DCB119

Definitions: Safety Guidelines

The definitions below describe the level of severity for each signal word. Please read the manual and pay attention to thesesymbols.

DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or



seriousinjury. WARNING: Indicates a potentially hazardous situation

which, if not avoided, could result in death or



seriousinjury. CAUTION: Indicates a potentially hazardous situation

which, if not avoided, may result in minor or



moderateinjury. NOTICE: Indicates a practice not related to

personal injury which, if not avoided, may result in propertydamage.

Denotes risk of electricshock.



Denotes risk offire.



General Power Tool Safety Warnings

WARNING: Read all safety warnings and all instructions. Failure to follow the warnings and



instructions may result in electric shock, fire and/or seriousinjury.

SAVE ALL WARNINGS AND INSTRUCTIONS

FOR FUTURE REFERENCE

The term “power tool” in the warnings refers to your mainsoperated (corded) power tool or battery-operated (cordless) powertool.

1) Work area safety

a ) Keep work area clean and well lit. Cluttered or dark

areas inviteaccidents.

b ) Do not operate power tools in explosive

atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which

may ignite the dust orfumes.

c ) Keep children and bystanders away while operating

a power tool. Distractions can cause you to losecontrol.

2) Electrical safety

a ) Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools.

Unmodified plugs and matching outlets will reduce risk of electricshock.

b ) Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if

your body is earthed orgrounded.

c ) Do not expose power tools to rain or wet conditions.

Water entering a power tool will increase the risk of electricshock.

d ) Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of

electricshock.

e ) When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electricshock.

f ) If operating a power tool in a damp location is

unavoidable, use a residual current device (RCD) protected supply. Use of an RCD reduces the risk of

electricshock.

3) Personal safety

a ) Stay alert, watch what you are doing and use

common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment

of inattention while operating power tools may result in serious personalinjury.

b ) Use personal protective equipment. Always wear

eye protection. Protective equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personalinjuries.

c ) Prevent unintentional starting. Ensure the switch

is in the off position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the

switch or energising power tools that have the switch on invitesaccidents.

Page 7

d ) Remove any adjusting key or wrench before turning

the power tool on. A wrench or a key left attached

to a rotating part of the power tool may result in personalinjury.

e ) Do not overreach. Keep proper footing and balance

at all times. This enables better control of the power tool in unexpectedsituations.

f ) Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewellery or long hair

can be caught in movingparts.

g ) If devices are provided for the connection of dust

extraction and collection facilities, ensure these are connected and properly used. Use of dust collection

can reduce dust-relatedhazards.

4) Power tool use and care

a ) Do not force the power tool. Use the correct power

tool for your application. The correct power tool

will do the job better and safer at the rate for which it wasdesigned.

b ) Do not use the power tool if the switch does not turn

it on and off. Any power tool that cannot be controlled with the switch is dangerous and must berepaired.

c ) Disconnect the plug from the power source and/or

the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the

risk of starting the power toolaccidentally.

d ) Store idle power tools out of the reach of children

and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool.

Power tools are dangerous in the hands of untrainedusers.

e ) Maintain power tools. Check for misalignment or

binding of moving parts, breakage of parts and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly

maintained powertools.

f ) Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are less likely to bind and are easier tocontrol.

g ) Use the power tool, accessories and tool bits etc.,

in accordance with these instructions taking into account the working conditions and the work to be performed. Use of the power tool for operations different

from those intended could result in a hazardoussituation.

5) Battery tool use and care

a ) Recharge only with the charger specified by the

manufacturer. A charger that is suitable for one type

of battery pack may create a risk of fire when used with another batterypack.

b ) Use power tools only with specifically designated

battery packs. Use of any other battery packs may create a risk of injury andfire.

ENGLISH

c ) When battery pack is not in use, keep it away from

other metal objects like paper clips, coins, keys, nails, screws or other small metal objects that can make a connection from one terminal to another.

Shorting the battery terminals together may cause burns or afire.

d ) Under abusive conditions, liquid may be ejected

from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid

ejected from the battery may cause irritation orburns.

6) Service

a ) Have your power tool serviced by a qualified repair

person using only identical replacement parts. This

will ensure that the safety of the power tool ismaintained.

Additional Specific Safety Rules for Drill/ Driver/Hammerdrill

• Wear ear protectors when impact drilling. Exposure to

noise can cause hearingloss.

• Use auxiliary handle(s), if supplied with the tool. Loss of

control can cause personalinjury.

• Hold power tool by insulated gripping surfaces, when

performing an operation where the cutting accessory may contact hidden wiring. Cutting accessory contacting

a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electricshock.

• Use clamps or other practical way to secure and support the workpiece to a stable platform. Holding the work by hand or against your body is unstable and may lead to loss ofcontrol.

• Wear safety goggles or other eye protection. Hammering and drilling operations cause chips to fly. Flying particles can cause permanent eyedamage.

• Accessories and tool may get hot during operation. Wear gloves when handling them if performing heat producing applications such as hammerdrilling and drillingmetals.

• Do not operate this tool for long periods of time. Vibration caused by hammer action may be harmful to your hands and arms. Use gloves to provide extra cushion and limit exposure by taking frequent restperiods.

• Air vents often cover moving parts and should be avoided. Loose clothes, jewelry or long hair can be caught in movingparts.

Residual Risks

In spite of the application of the relevant safety regulations and the implementation of safety devices, certain residual risks cannot be avoided. These are:

• Impairment ofhearing.

• Risk of squeezing fingers when changingaccessories.

• Health hazards caused by breathing dust developed when working inwood.

• Risk of personal injury due to flyingparticles.

• Risk of personal injury due to prolongeduse.

Page 8

ENGLISH

DeWALT

Electrical Safety

The electric motor has been designed for one voltage only. Always check that the battery pack voltage corresponds to the voltage on the rating plate. Also make sure that the voltage of your charger corresponds to that of yourmains.

Your accordance with EN60335; therefore no earth wire isrequired.

If the supply cord is damaged, it must be replaced by a specially prepared cord available through the serviceorganisation.

Mains Plug Replacement (U.K. & Ireland Only)

If a new mains plug needs to be fitted:

• Safely dispose of the oldplug.

• Connect the brown lead to the live terminal in theplug.

• Connect the blue lead to the neutralterminal.

WARNING: No connection is to be made to the earthterminal.



Follow the fitting instructions supplied with good quality plugs. Recommended fuse: 3A.

Using an Extension Cable

An extension cord should not be used unless absolutely necessary. Use an approved extension cable suitable for the power input of your charger (see Technical Data). The minimum conductor size is 1mm2; the maximum length is30m.

When using a cable reel, always unwind the cablecompletely.

SAVE THESE INSTRUCTIONS

charger is double insulated in

Chargers

chargers require no adjustment and are designed to be

as easy as possible tooperate.

Important Safety Instructions for All Battery Chargers

SAVE THESE INSTRUCTIONS: This manual contains important safety and operating instructions for compatible battery chargers (refer to TechnicalData).

• Before using charger, read all instructions and cautionary markings on charger, battery pack, and product using batterypack.

WARNING: Shock hazard. Do not allow any liquid to get inside charger. Electric shock mayresult.



WARNING: We recommend the use of a residual current device with a residual current rating of 30mA orless.



CAUTION: Burn hazard. To reduce the risk of injury, charge only



batteries may burst causing personal injury anddamage. CAUTION: Children should be supervised to ensure that

they do not play with theappliance.



NOTICE: Under certain conditions, with the charger plugged into the power supply, the exposed charging contacts inside the charger can be shorted by foreign

rechargeable batteries. Other types of

material. Foreign materials of a conductive nature such as, but not limited to, steel wool, aluminum foil or any buildup of metallic particles should be kept away from charger cavities. Always unplug the charger from the power supply when there is no battery pack in the cavity. Unplug charger before attempting to clean

• DO NOT attempt to charge the battery pack with any chargers other than the ones in this manual. The charger and battery pack are specifically designed to worktogether.

• These chargers are not intended for any uses other than

charging

may result in risk of fire, electric shock orelectrocution.

• Do not expose charger to rain orsnow.

• Pull by plug rather than cord when disconnecting charger. This will reduce risk ofdamage to electric plug andcord.

• Make sure that cord is located so that it will not be

stepped on, tripped over, or otherwise subjected to damage orstress.

• Do not use an extension cord unless it is absolutely necessary. Use of improper extension cord could result in risk

of fire,electric shock, orelectrocution.

• Do not place any object on top of charger or place

the charger on a soft surface that might block the ventilation slots and result in excessive internal heat.

Place the charger in a position away from any heat source. The charger is ventilated through slots in the top and the bottom of thehousing.

• Do not operate charger with damaged cord or plug— have them replacedimmediately.

• Do not operate charger if it has received a sharp blow, been dropped, or otherwise damaged in any way. Take it to an authorised servicecentre.

• Do not disassemble charger; take it to an authorised service centre when service or repair is required. Incorrect reassembly may result in a risk of electric shock, electrocution orfire.

• In case of damaged power supply cord the supply cord must be replaced immediately by the manufacturer, its service agent or similar qualified person to prevent anyhazard.

• Disconnect the charger from the outlet before

attempting any cleaning. This will reduce the risk of electric shock. Removing the battery pack will not reduce

thisrisk.

• NEVER attempt to connect two chargerstogether.

• The charger is designed to operate on standard

230V household electrical power. Do not attempt to use it on any other voltage. This does not apply to the

vehicularcharger.

Charging a Battery (Fig. B)

1. Plug the charger into an appropriate outlet before inserting batterypack.

2. Insert the battery pack battery pack is fully seated in the charger. The red (charging)

rechargeable batteries. Any other uses

10

into the charger, making sure the

Page 9

light will blink repeatedly indicating that the charging

DeWALT

process hasstarted.

3. The completion of charge will be indicated by the red light remaining ON continuously. The battery pack is fully charged and may be used at this time or left in the charger. To remove the battery pack from the charger, push the battery release button

NOTE: To ensure maximum performance and life of lithium-ion battery packs, charge the battery pack fully before firstuse.

11

on the batterypack.

Charger Operation

Refer to the indicators below for the charge status of the batterypack.

Charge Indicators

Charging

Fully Charged

Hot/Cold Pack Delay*

* The red light will continue to blink, but a yellow indicator light

will be illuminated during this operation. Once the battery pack has reached an appropriate temperature, the yellow light will turn off and the charger will resume the chargingprocedure.

The compatible charger(s) will not charge a faulty battery pack. The charger will indicate faulty battery by refusing to light or by displaying problem pack or charger blinkpattern.

NOTE: This could also mean a problem with acharger. If the charger indicates a problem, take the charger and battery

pack to be tested at an authorised servicecentre.

Hot/Cold Pack Delay

When the charger detects a battery pack that is too hot or too cold, it automatically starts a Hot/Cold Pack Delay, suspending charging until the battery pack has reached an appropriate temperature. The charger then automatically switches to the pack charging mode. This feature ensures maximum battery packlife.

A cold battery pack will charge at a slower rate than a warm battery pack. The battery pack will charge at that slower rate throughout the entire charging cycle and will not return to maximum charge rate even if the battery packwarms.

The DCB118 charger is equipped with an internal fan designed to cool the battery pack. The fan will turn on automatically when the battery pack needs to be cooled. Never operate the charger if the fan does not operate properly or if ventilation slots are blocked. Do not permit foreign objects to enter the interior of thecharger.

Electronic Protection System

XR Li-Ion tools are designed with an Electronic Protection System that will protect the battery pack against overloading, overheating or deepdischarge.

The tool will automatically turn off if the Electronic Protection System engages. If this occurs, place the lithium-ion battery pack on the charger until it is fullycharged.

ENGLISH

Wall Mounting

These chargers are designed to be wall mountable or to sit upright on a table or work surface. If wall mounting, locate the charger within reach of an electrical outlet, and away from a corner or other obstructions which may impede air flow. Use the back of the charger as a template for the location of the mounting screws on the wall. Mount the charger securely using drywall screws (purchased separately) at least 25.4mm long with a screw head diameter of 7–9mm, screwed into wood to an optimal depth leaving approximately 5.5mm of the screw exposed. Align the slots on the back of the charger with the exposed screws and fully engage them in theslots.

Charger Cleaning Instructions

WARNING: Shock hazard. Disconnect the charger from the AC outlet before cleaning. Dirt and grease



may be removed from the exterior of the charger using a cloth or soft non-metallic brush. Do not use water or any cleaning solutions. Never let any liquid get inside the tool; never immerse any part of the tool into aliquid.

Battery Packs

Important Safety Instructions for All Battery Packs

When ordering replacement battery packs, be sure to include catalogue number andvoltage.

The battery pack is not fully charged out of the carton. Before using the battery pack and charger, read the safety instructions below. Then follow charging proceduresoutlined.

READ ALL INSTRUCTIONS

• Do not charge or use battery in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Inserting or removing the battery from the charger may

ignite the dust orfumes.

• Never force battery pack into charger. Do not modify

battery pack in any way to fit into a non-compatible charger as battery pack may rupture causing serious personalinjury.

• Charge the battery packs only in

• DO NOT splash or immerse in water or otherliquids.

• Do not store or use the tool and battery pack in

locations where the temperature may reach or exceed 40 ˚C (104 ˚F) (such as outside sheds or metal buildings in summer).

• Do not incinerate the battery pack even if it is severely damaged or is completely worn out. The battery pack can

explode in a fire. Toxic fumes and materials are created when lithium-ion battery packs areburned.

• If battery contents come into contact with the skin, immediately wash area with mild soap and water. If battery liquid gets into the eye, rinse water over the open eye for 15 minutes or until irritation ceases. If medical attention is needed, the battery electrolyte is composed of a mixture of liquid organic carbonates and lithiumsalts.

chargers.

Page 10

ENGLISH

DeWALT

• Contents of opened battery cells may cause respiratory irritation. Provide fresh air. If symptoms persists, seek

medicalattention.

WARNING: Burn hazard. Battery liquid may be flammable if exposed to spark orflame.



WARNING: Never attempt to open the battery pack for any reason. If battery pack case is cracked or damaged,



do not insert into charger. Do not crush, drop or damage battery pack. Do not use a battery pack or charger that has received a sharp blow, been dropped, run over or damaged in any way (i.e., pierced with a nail, hit with a hammer, stepped on). Electric shock or electrocution may result. Damaged battery packs should be returned to service centre forrecycling.

WARNING: Fire hazard. Do not store or carry the battery pack so that metal objects can contact



exposed battery terminals. For example, do not place the battery pack in aprons, pockets, tool boxes, product kit boxes, drawers, etc., with loose nails, screws, keys,etc.

CAUTION: When not in use, place tool on its side on a stable surface where it will not cause a tripping



or falling hazard. Some tools with large battery packs will stand upright on the battery pack but may be easily knockedover.

Transportation

WARNING: Fire hazard. Transporting batteries can possibly cause fire if the battery terminals inadvertently



come in contact with conductive materials. When transporting batteries, make sure that the battery terminals are protected and well insulated from materials that could contact them and cause a shortcircuit.

batteries comply with all applicable shipping regulations as prescribed by industry and legal standards which include UN Recommendations on the Transport of Dangerous Goods; International Air Transport Association (IATA) Dangerous Goods Regulations, International Maritime Dangerous Goods (IMDG) Regulations, and the European Agreement Concerning The International Carriage of Dangerous Goods by Road (ADR). Lithium-ion cells and batteries have been tested to section 38.3 of the UN Recommendations on the Transport of Dangerous Goods Manual of Tests andCriteria.

In most instances, shipping a excepted from being classified as a fully regulated Class 9 Hazardous Material. In general, only shipments containing a lithium-ion battery with an energy rating greater than 100 Watt Hours (Wh) will require being shipped as fully regulated Class 9. All lithium-ion batteries have the Watt Hour rating marked on the pack. Furthermore, due to regulation complexities, does not recommend air shipping lithium-ion battery packs alone regardless of Watt Hour rating. Shipments of tools with batteries (combo kits) can be air shipped as excepted if the Watt Hour rating of the battery pack is no greater than 100Whr.

Regardless of whether a shipment is considered excepted or fully regulated, it is the shipper's responsibility to consult the latest regulations for packaging, labeling/marking and documentationrequirements.

battery pack will be

The information provided in this section of the manual is provided in good faith and believed to be accurate at the time the document was created. However, no warranty, expressed or implied, is given. It is the buyer’s responsibility to ensure that its activities comply with the applicableregulations.

Transporting the FLEXVOLTTM Battery

The andTransport.

Use Mode: When the FLEXVOLTTM battery stands alone or is in a the FLEXVOLTTM battery is in a 54V or a 108V (two 54V batteries) product, it will operate as a 54Vbattery.

Transport Mode: When the cap is attached to the FLEXVOLTTM battery, the battery is in Transport mode. Keep the cap for shipping.

When in Transport mode, strings of cells are electrically disconnected within the pack resulting in 3 batteries with a lower Watt hour (Wh) rating as compared to 1 battery with a higher Watt hour rating. This increased quantity of 3 batteries with the lower Watt hour rating can exempt the pack from certain shipping regulations that are imposed upon the higher Watt hour batteries.

For example, the Transport Wh rating might indicate 3x36 Wh, meaning 3 batteries of 36 Wh each. The Use Wh rating might indicate 108Wh (1battery implied).

Storage Recommendations

1. The best storage place is one that is cool and dry away

2. For long storage, it is recommended to store a fully charged

NOTE: Battery packs should not be stored completely depleted of charge. The battery pack will need to be recharged beforeuse.

Labels on Charger and Battery Pack

In addition to the pictographs used in this manual, the labels on the charger and the battery pack may show the following pictographs:

FLEXVOLTTM battery has two modes: Use

18V product, it will operate as an 18V battery. When

Example of Use and Transport Label Marking

from direct sunlight and excess heat or cold. For optimum battery performance and life, store battery packs at room temperature when not inuse.

battery pack in a cool, dry place out of the charger for optimalresults.

Read instruction manual beforeuse.

See Technical Data for chargingtime.

Page 11

Do not probe with conductiveobjects.

DeWALT

Do not charge damaged batterypacks.

Do not expose to water.

ENGLISH

• Check for damage to the tool, parts or accessories which may have occurred duringtransport.

• Take the time to thoroughly read and understand this manual prior tooperation.

Markings on Tool

The following pictograms are shown on the tool:

Have defective cords replacedimmediately.

Charge only between 4 ˚C and 40 ˚C.

Only for indooruse.

Discard the battery pack with due care for theenvironment.

Charge

than the designated

other dangeroussituations.

Do not incinerate the batterypack.

USE (without transport cap). Example: Wh rating indicates 108 Wh (1 battery with 108 Wh).

TRANSPORT (with built-in transport cap). Example: Wh rating indicates 3 x 36 Wh (3batteries of 36 Wh).

battery packs only with designated

chargers. Charging battery packs other

charger may make them burst or lead to

batteries with a

Battery Type

The DCD791 and DCD796 operate on a 18 volt batterypack. These battery packs may be used: DCB181, DCB182, DCB183,

DCB183B, DCB184, DCB184B, DCB185, DCB187, DCB546, DCB547. Refer to Technical Data for moreinformation.

Package Contents

The package contains: 1 Drill/driver or 1 drill/driver/hammerdrill 1 Charger 1 Li-Ion battery pack (C1, D1, L1, M1, P1, S1, T1, X1 models) 2 Li-Ion battery packs (C2, D2, L2, M2, P2, S2, T2, X2 models) 3 Li-Ion battery packs (C3, D3, L3, M3, P3, S3, T3, X3 models) 1 Kitbox 1 Instruction manual 1 Tool Connect™ App instruction manual (Bmodels) NOTE: Battery packs, chargers and kitboxes are not included

with N models. Battery packs and chargers are not included with NT models. Bmodels include Bluetooth® batterypacks.

NOTE: The Bluetooth® word mark and logos are registered trademarks owned by the Bluetooth®, SIG, Inc. and any use of such marks by trade names are those of their respectiveowners.

is under license. Other trademarks and

Read instruction manual beforeuse.

Visible radiation. Do not stare intolight.

Date Code Position (Fig. A)

The date code is printed into thehousing.

Example:

16

, which also includes the year of manufacture,

2017 XX XX

Year of Manufacture

Description (Fig. A)

WARNING: Never modify the power tool or any part of it. Damage or personal injury couldresult.



Trigger switch

Forward/reverse control button

Torque adjustment collar

Gear shifter

Worklight

Keyless chuck

Belt hook

Mounting screw

Bit clip

Battery pack

Battery release button

Worklight switch

Intended Use

These drills/drivers/hammerdrills are designed for professional drilling, percussion drilling and screwdrivingapplications.

DO NOT use under wet conditions or in the presence of flammable liquids orgases.

These drills/drivers/hammerdrills are professional powertools. DO NOT let children come into contact with the tool.

Supervision is required when inexperienced operators use thistool.

• Young children and the infirm. This appliance is not intended for use by young children or infirm persons withoutsupervision.

• This product is not intended for use by persons (including children) suffering from diminished physical, sensory or mental abilities; lack of experience, knowledge or skills unless they are supervised by a person responsible for their safety. Children should never be left alone with thisproduct.

Page 12

ENGLISH

DeWALT

ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of serious personal injury, turn tool off and disconnect battery pack



before making any adjustments or removing/ installing attachments or accessories. An accidental

start-up can causeinjury.

WARNING: Use only



battery packs andchargers.

Inserting and Removing the Battery Pack from the Tool (Fig. B)

NOTE: Make sure your battery pack

To Install the Battery Pack into the Tool Handle

1. Align the battery pack handle (Fig. B).

2. Slide it into the handle until the battery pack is firmly seated in the tool and ensure that you hear the lock snap intoplace.

To Remove the Battery Pack from the Tool

1. Press the release button out of the toolhandle.

2. Insert battery pack into the charger as described in the charger section of thismanual.

Fuel Gauge Battery Packs (Fig. B)

Some consists of three green LED lights that indicate the level of charge remaining in the batterypack.

To actuate the fuel gauge, press and hold the fuel gauge button. A combination of the three green LED lights will illuminate designating the level of charge left. When the level of charge in the battery is below the usable limit, the fuel gauge will not illuminate and the battery will need to berecharged.

NOTE: The fuel gauge is only an indication of the charge left on the battery pack. It does not indicate tool functionality and is subject to variation based on product components, temperature and end-userapplication.

battery packs include a fuel gauge which

10

is fullycharged.

10

with the rails inside the tool’s

11

and firmly pull the battery pack

Variable Speed Trigger Switch (Fig. A)

To turn the tool on, squeeze the trigger switch tool off, release the trigger switch. Your tool is equipped with a brake. The chuck will stop as soon as the trigger switch is fullyreleased.

NOTE: Continuous use in variable speed range is not recommended. It may damage the switch and should beavoided.

1

. To turn the

Forward/Reverse Control Button (Fig. A)

A forward/reverse control button the tool and also serves as a lock-offbutton.

To select forward rotation, release the trigger switch and press the forward/reverse control button on the right side of thetool.

To select reverse, press the forward/reverse control button on the left side of thetool.

2

determines the direction of

The centre position of the control button locks the tool in the off position. When changing the position of the control button, be sure the trigger isreleased.

NOTE: The first time the tool is run after changing the direction of rotation, you may hear a click on start up. This is normal and does not indicate aproblem.

Torque Adjustment Collar (Fig. A)

Your tool has an adjustable torque screwdriver mechanism for driving and removing a wide array of fastener shapes and sizes and in some models, a hammer mechanism for drilling into masonry. Circling the collar and in some models, a hammer symbol. These numbers are used to set the clutch to deliver a torque range. The higher the number on the collar, the higher the torque and the larger the fastener which can be driven. To select any of the numbers, rotate until the desired number aligns with thearrow.

NOTE: The torque adjustment collar is only engaged during screwdriving mode and not in drill and hammerdrillmodes.

3

are numbers, a drill bit symbol,

Dual Range Gearing (Fig. A)

The dual range feature of your drill/driver allows you to shift gears for greaterversatility.

1. To select speed 1 (high torque setting), turn the tool off and permit it to stop. Slide the gear shifter the chuck).

2. To select speed 2 (low torque setting), turn the tool off and permit it to stop. Slide the gear shifter back (away from thechuck).

NOTE: Do not change gears when the tool is running. Always allow the drill to come to a complete stop before changing gears. If you are having trouble changing gears, make sure that the dual range gear shifter is either completely pushed forward or completely pushedback.

4

forward (towards

LED Worklight (Fig. A)

The LED worklight the foot of the tool. The worklight is activated when the trigger switch is depressed. The low modes can be changed by moving the switch on the foot of the tool. If the trigger switch remains depressed, the worklight will remain on in allmodes.

When on low automatically turn off 20 seconds after the trigger switch isreleased.

5

and its worklight switch

13

and medium

, medium

14

settings, the beam will

Spotlight Mode

The high setting run for 20 minutes after the trigger switch is released. Two minutes before the spotlight will shut off, it will flash twice and then dim. To avoid the spotlight shutting off, lightly tap the triggerswitch.



15

is the spotlight mode. The spotlight will

WARNING: While using the worklight in medium or spotlight mode, do not stare at the light or place the drill in a position which may cause anyone to stare into the light. Serious eye injury couldresult.

12

are located on

14

and spotlight

15

Page 13

CAUTION: When using the tool as a spotlight, be sure it is secured on a stable surface where it will not cause a



tripping or fallinghazard. CAUTION: Remove all accessories from the chuck before

using the drill as a spotlight. Personal injury or property



damage couldresult.

Low Battery Warning

When in spotlight mode and the battery is nearing complete discharge, the spotlight will flash twice and then dim. After two minutes, the battery will be completely discharged and the drill will immediately shut down. At this point, replace with a chargedbattery.

WARNING: To reduce the risk of injury, always have a back-up battery or secondary lighting available if the



situation warrantsit.

Keyless Single Sleeve Chuck (Fig. G–I)

WARNING: Do not attempt to tighten drill bits (or any other accessory) by gripping the front part of the



chuck and turning the tool on. Damage to the chuck and personal injury may result. Always lock off trigger switch and disconnect tool from power source when changingacces sories.

WARNING: Always ensure the bit is secure before starting the tool. A loose bit may eject from tool causing possible



personalinjury.

Your tool features a keyless chuck one-handed operation of the chuck. To insert a drill bit or other accessory, follow thesesteps.

1. Turn tool off and disconnect tool from powersource.

2. Grasp the black sleeve of the chuck with one hand and use the other hand to secure the tool. Rotate the sleeve counterclockwise far enough to accept the desiredaccessory.

3. Insert the accessory about 19 mm (3/4") into the chuck and tighten securely by rotating the chuck sleeve clockwise with one hand while holding the tool with the other. Your tool is equipped with an automatic spindle lock mechanism. This allows you to open and close the chuck with onehand. NOTE: Be sure to tighten chuck with one hand on the chuck sleeve and one hand holding the tool for maximumtightness.

To release the accessory, repeat steps 1 and 2above.

6

with one rotating sleeve for

Belt Hook and Bit Clip (Fig. A)

WARNING: To reduce the risk of serious personal injury, turn tool off and disconnect battery pack



before making any adjustments or removing/ installing attachments oraccessories.

WARNING: To reduce the risk of serious personal injury, DO NOT suspend tool overhead or suspend



objects from the belt hook. ONLY hang tool’s belt hook from a workbelt.

WARNING: To reduce the risk of serious personal injury, ensure the screw holding the belt hook issecure.



ENGLISH

IMPORTANT: When attaching or replacing the belt hook or bit

clip, use only the screw tighten thescrew.

The belt hook either side of the tool using only the screw accommodate left- or right- handed users. If the hook or bit clip is not desired at all, it can be removed from thetool.

To move belt hook or bit clip, remove the screw it in place then reassemble on the opposite side. Be sure to securely tighten thescrew.

7

and bit clip

8

that is provided. Be sure to securely

9

can be be attached to

8

provided, to

8

that holds

OPERATION

Instructions for Use

WARNING: Always observe the safety instructions and applicableregulations.



WARNING: To reduce the risk of serious personal injury, turn tool off and disconnect battery pack



before making any adjustments or removing/ installing attachments or accessories. An accidental

start-up can causeinjury.

Proper Hand Position (Fig. C)

WARNING: To reduce the risk of serious personal injury, ALWAYS use proper hand position asshown.



WARNING: To reduce the risk of serious personal injury, ALWAYS hold securely in anticipation of a



suddenreaction.

Proper hand position requires one hand on the top of the

17

drill

as shown, with the other hand on the main handle

18

Drill Operation (Fig. A, D)

WARNING: TO REDUCE THE RISK OF PERSONAL INJURY, ALWAYS ensure workpiece is anchored or



clamped firmly. If drilling thin material, use a wood “backup” block to prevent damage to thematerial.

1. Turn the collar

2. Select the desired speed/torque range using the gear shifter

4

to match the speed and torque to the plannedoperation.

3. For Wood, use twist bits, spade bits, power auger bits or hole saws. For Metal, use high-speed steel twist drill bits or hole saws. Use a cutting lubricant when drilling metals. The exceptions are cast iron and brass which should be drilleddry.

4. Always apply pressure in a straight line with the bit. Use enough pressure to keep drill biting, but do not push hard enough to stall the motor or deflect thebit.

5. Hold tool firmly with both hands to control the twisting action of the drill. If model is not equipped with side handle, grip drill with one hand on the handle and one hand on the batterypack.

CAUTION: Drill may stall if overloaded causing a sudden twist. Always expect the stall. Grip the drill firmly to control



the twisting action and avoidinjury.

6. IF DRILL STALLS, it is usually because it is being overloaded or improperly used. RELEASE TRIGGER IMMEDIATELY,

3

to the drillsymbol.

Page 14

ENGLISH

DeWALT

remove drill bit from work, and determine cause of stalling. DO NOT CLICK TRIGGER ON AND OFF IN AN ATTEMPT TO START A STALLED DRILL — THIS CAN DAMAGE THEDRILL.

7. To minimise stalling or breaking through the material, reduce pressure on drill and ease the bit through the last fractional part of thehole.

8. Keep the motor running when pulling the bit back out of a drilled hole. This will help preventjamming.

9. With variable speed drills there is no need to centre punch the point to be drilled. Use a slow speed to start the hole and accelerate by squeezing the trigger harder when the hole is deep enough to drill without the bit skippingout.

Hammerdrill Operation (DCD796 only) (Fig. A, E)

1. Turn the collar

2. Select the high speed shifter IMPORTANT: Use carbide-tipped or masonry bitsonly.

3. Drill with just enough force on the hammer to keep it from bouncing excessively or “rising” off the bit. Too much force will cause slower drilling speeds, overheating and lower drillingrate.

4. Drill straight, keeping the bit at a right angle to the work. Do not exert side pressure on the bit when drillling as this will cause clogging of the bit flutes and a slower drillingspeed.

5. When drilling deep holes, if the hammer speed starts to drop off, pull the bit partially out of the hole with tool stil running to help clear debris from thehole.

NOTE: A smooth, even flow of dust from the hole indicates proper drillingrate.

3

to the hammerdrillsymbol.

2

4

back (away from the chuck).

setting by sliding the gear

Screwdriver Operation (Fig. A, F)

1. Turn the torque adjustment collar

2. Select the desired speed/torque range using the gear shifter plannedoperation. NOTE: Use the lowest torque setting required to seat the fastener at the desired depth. The lower the number, the lower the torqueoutput.

3. Insert the desired fastener accessory into the chuck as you would any drillbit.

4. Make some practice runs in scrap or on unseen areas to determine the proper position of the clutchcollar.

5. Always start with lower torque settings, then advance to higher torque settings to avoid damage to the workpiece orfastener.

4

to match the speed and torque of the

3

to the desiredposition.

MAINTENANCE

Your over a long period of time with a minimum of maintenance. Continuous satisfactory operation depends upon proper tool care and regularcleaning.

power tool has been designed to operate

WARNING: To reduce the risk of serious personal injury, turn tool off and disconnect battery pack



before making any adjustments or removing/ installing attachments or accessories. An accidental

start-up can causeinjury.

The charger and battery pack are notserviceable.

Lubrication

Your power tool requires no additionallubrication.

Cleaning

WARNING: Blow dirt and dust out of the main housing with dry air as often as dirt is seen collecting in and around



the air vents. Wear approved eye protection and approved dust mask when performing thisprocedure.

WARNING: Never use solvents or other harsh chemicals for cleaning the non-metallic parts of the tool. These



chemicals may weaken the materials used in these parts. Use a cloth dampened only with water and mild soap. Never let any liquid get inside the tool; never immerse any part of the tool into aliquid.

Optional Accessories

WARNING: Since accessories, other than those offered by



of such accessories with this tool could be hazardous. To reduce the risk of injury, only accessories should be used with thisproduct.

Consult your dealer for further information on the appropriateaccessories.

, have not been tested with this product, use

recommended

Protecting the Environment

Separate collection. Products and batteries marked with this symbol must not be disposed of with normal householdwaste.

Products and batteries contain materials that can be recovered or recycled reducing the demand for raw materials. Please recycle electrical products and batteries according to local provisions. Further information is available at www.2helpU.com.

Rechargeable Battery Pack

This long life battery pack must be recharged when it fails to produce sufficient power on jobs which were easily done before. At the end of its technical life, discard it with due care for our environment:

• Run the battery pack down completely, then remove it from

thetool.

• Li-Ion cells are recyclable. Take them to your dealer or a

local recycling station. The collected battery packs will be recycled or disposed ofproperly.

Page 15

Page 16

Belgique et Luxembourg België en Luxemburg

DeWALT - Belgium BVBA Egide Walschaertsstraat 16 2800 Mechelen

Tel: NL 32 15 47 37 63 Tel: FR 32 15 47 37 64 Fax: 32 15 47 37 99

www.dewalt.be enduser.BE@SBDinc.com

Danmark DeWALT (Stanley Black&Decker AS)

Roskildevej 22 2620 Albertslund

Tel: 70 20 15 10 Fax: 70 22 49 10

www.dewalt.dk kundeservice.dk@sbdinc.com

Deutschland DeWALT

Richard Klinger Str. 11 65510 Idstein

Tel: 06126-21-0 Fax: 06126-21-2770

www.dewalt.de infodwge@sbdinc.com

Ελλάς DeWALT (Ελλάς) Α.Ε.

EΔΡΑ-ΓΡΑΦΕΙΑ : Στράβωνος 7 & Λ. Βουλιαγμένης, Γλυφάδα 166 74, Αθήνα SERVICE : Ημερος Τόπος 2 (Χάνι Αδάμ) – 193 00 Ασπρόπυργος

Τηλ: 00302108981616 Φαξ: 00302108983570

www.dewalt.gr Greece.Service@sbdinc.com

España DeWALT Ibérica, S.C.A.

Parc de Negocios “Mas Blau” Edificio Muntadas, c/Bergadá, 1, Of. A6 08820 El Prat de Llobregat (Barcelona)

Tel: 934 797 400 Fax: 934 797 419

www.dewalt.es respuesta.postventa@sbdinc.com

France DeWALT

5, allée des Hêtres BP 60105, 69579 Limonest Cedex

Tel: 04 72 20 39 20 Fax: 04 72 20 39 00

www.dewalt.fr scufr@sbdinc.com

Schweiz Suisse Svizzera

DeWALT In der Luberzen 42 8902 Urdorf

Tel: 044 - 755 60 70 Fax: 044 - 730 70 67

www.dewalt.ch service@rofoag.ch

Ireland DeWALT

Building 4500, Kinsale Road Cork Airport Business Park Cork, Ireland

Tel: 00353-2781800 Fax: 01278 1811

www.dewalt.ie Sales.ireland@sbdinc.com

Italia DeWALT

via Energypark 6 20871 Vimercate (MB), IT

Tel: 800-014353 39 039-9590200 Fax: 39 039-9590311

www.dewalt.it

Nederlands DeWALT

Netherlands BVPostbus 83, 6120 AB BORN

Tel: 31 164 283 063 Fax: 31 164 283 200

www.dewalt.nl

Norge DeWALT

Postboks 4613 0405 Oslo, Norge

Tel: 45 25 13 00 Fax: 45 25 08 00

www.dewalt.no kundeservice.no@sbdinc.com

Österreich DeWALT

Werkzeug Vertriebsges m.b.H Oberlaaerstrasse 248, A-1230 Wien

Tel: 01 - 66116 - 0 Fax: 01 - 66116 - 614

www.dewalt.at service.austria@sbdinc.com

Portugal DeWALT

Ed. D Dinis, Quina da Fonte Rua dos Malhoes 2 2A 2º Esq. Oeiras e S. Juliao da Barra, paço de Arcos e Caxias 2770 071 Paço de Arcos

Tel: +351 214667500 Fax: +351214667580

www.dewalt.pt resposta.posvenda@sbdinc.com

Suomi DeWALT

PL47 00521 Helsinki, Suomi

Puh: 010 400 4333 Faksi: 0800 411 340

www.dewalt.fi asiakaspalvelu.fi@sbdinc.com

Sverige DeWALT

BOX 94 43122 Mölndal Sverige

Tel: 031 68 61 60 Fax: 031 68 60 08

www.dewalt.se kundservice.se@sbdinc.com

Türkiye

Sanayi ve Ticareet Bakanlığı tebliğince kullanim ömrü 7 yıldır. Stanley Black & Decker Turkey Alet Üretim San. Tic. Ltd.Şti. Kozyataği Mh Değirmen Sk. Nida Kule No: 18 Kat: 6, 34742 Kadıköy, İstanbul, Türkiye

Tel: +90 216 665 2900 Faks: +90 216 665 2901

www.dewalt.com.tr info-tr@sbdinc.com

United Kingdom

DeWALT, 210 Bath Road; Slough, Berks SL1 3YD

Tel: 01753-567055 Fax: 01753-572112

www.dewalt.co.uk emeaservice@sbdinc.com

Australia DeWALT

810 Whitehorse Road Box Hill VIC 3103 Australia

Tel: Aust 1800 338 002 Tel: NZ 0800 339 258

www.dewalt.com.au www.dewalt.co.nz

Middle East Africa DeWALT

P.O. Box - 17164, Jebel Ali Free Zone (South), Dubai, UAE

Tel: 971 4 812 7400 Fax: 971 4 2822765

www.dewalt.ae Service.MEA@sbdinc.com

N542469

07/17