FC-1
High-Performance Portable Platform
Operation Manual
Ver 1.20
Deviser Part No.: FC-1
© Tianjin Deviser Electronics Instrument Co.， Ltd.
All rights reserved.
Printed in CHINA， January. 2014.
Conventions
This manual has the following conventions for presenting information.
WARNING: A warning alerts you to any condition that could cause
personal injury.
CAUTION: A caution alerts you to any condition that could cause a
mechanical failure or potential loss of data.
Make sure the AC power supply voltage meet the equipment
requirements, otherwise it will cause an equipment failure.
Make sure to plug the power cable into an electrical outlet that has
safety grounding before turning on the power switch.
Touch the internal circuit may cause a mechanical failure or personnel
injury, so only trained engineers can remove the instrument cover and
maintain the instrument.
Guarantee
This instrument is guaranteed for a period of 12 months from the date of
shipment. Under warranty, any fault not caused by improper use will be
repaired for free.
Liability of the user: Use this instrument according to this instruction
manual. When this instrument needs to be repaired, please send it back
to our company or our appointed repair center.
The guarantee is limited only to the instrument and does not involve
any damage of equipment, personnel and property caused by improper
use of the instrument.
Limitation of Guarentee
The warranty is not applicable for the faults resulted by improper use or
inadequate maintenance (including software or interface), and
unauthorized open of the instrument. Within the 12 months warranty
period, calibration, maintenance service and consultation shall be free.
After the 12 months warranty period, fees for material and repair
workman will be charged reasonablely.
The following items are not under warranty:
A. Damages caused by improper voltage input.
B. Deformation or damage of panel, switches, devices and case as well
as defects involving interval parts caused by external mechanical force
(shocking, dropping, and etc.).
C. Defects caused by unauthorized repair.
D. Defects caused by the instrument worked beyond the required
technology specification.
Updates
Updates, if any, can be downloaded from the Deviser website
at:http://www.deviserinstruments.com
INDEX
1 Introduction ····································································· 1
2 Basic Feature ··································································· 2
2.1 Main Frame ································································· 2
2.2 Keyboard ···································································· 4
3 Function Description ························································· 6
3.1 Power On and Power Off ··············································· 6
3.1.1 Power On ····························································· 6
3.1.2 Power Off······························································ 6
3.2 Main Interface ······························································ 6
3.2.1 Status Bar ····························································· 7
3.2.2 Information Panel ··················································· 9
3.2.3 Application List Area ················································ 9
3.2.4 Switch Area ·························································· 10
3.3 Platform Application Programs ······································· 10
3.3.1 Time ··································································· 10
3.3.2 Net Setting ··························································· 10
3.3.3 Web Browser ························································ 11
3.3.4 File Manager ························································ 12
3.3.5 Application Manager ··············································· 12
3.3.6 Calibration ··························································· 14
3.3.7 Picture Viewer······················································· 14
3.3.8 Calculator ···························································· 15
3.3.9 Disk ···································································· 15
3.3.10 Update ······························································ 16
3.3.11 About ································································· 17
3.4 Soft Keyboard ····························································· 17
3.5 LCD Brightness Adjustment ··········································· 18
3.6 Charging ···································································· 19
4 Appendix ········································································ 20
FC-1 High-Performance Portable Platform Operation Manual
1
1 Introduction
FC-1 high-performance portable platform is developed by the Tianjin
Deviser Electronics Instrument Co.， Ltd, China. With compact size,
superior processing capabilities and highly intuitive interface, the field
technicians can perform OTDR, Ethernet testing and other multiservice
testing easily and efficiently. The platform meets the needs of
professional applications and helps you adapt to a variety of testing
needs.
Features and Benefits:
7 "(800X480) LCD display.
Excellent portable design and user-friendly site operation.
Large-capacity lithium battery with long standby and working time.
Quick, easy and user-friendly graphical user interface.
ARM11 hardware + Linux software platform.
Integrated software tools meet to field testing.
Remote control can be set up and operated through a browser.
Note: Before using the platform for the first time, please charge, as
detailed in the charging section.
FC-1 High-Performance Portable Platform Operation Manual
2
2 Basic Feature
2.1 Main Frame
Figure 2.1 Top Figure of Main Frame
①AC adapter jack
②Mini USB interface
③SD jack ④USB interface
⑤Communication RJ45
interface
⑥Function interface card
FC-1 High-Performance Portable Platform Operation Manual
3
Figure 2.2 Front Figure of Main Frame
⑦7"LCD color touch screen
⑧Module function indicators
⑨Module function keys
⑩Function operation keys
⑪Number and character keys
⑫Buzzer
⑬File manage key
⑭Menu key
⑮Configuration key
⑯LCD brightness adjustment key
⑰Power key
⑱Charge indicator light
⑲Instrument strap
FC-1 High-Performance Portable Platform Operation Manual
4
Figure 2.3 Back Figure of Main Frame
⑳Fan
Back support
Battery compartment cover
Battery compartment
screw
2.2 Keyboard
:
Power.
:
LCD brightness adjustment. With and keys, to
switch the backlight of the LCD between bright and dim.
FC-1 High-Performance Portable Platform Operation Manual
5
:
Configuration. To achieve the soft keyboard to bring up and
disappear.
:
Menu. To switch between Chinese and English in main
interface.
:
File management. To manage the system files, including
copy, paste, delete, rename and etc.
:
Ta b . To s witch controls in current selected interface.
:
Module function.
:
Number and character. To type a variety of characters and numbers in
text box.
:
Backspace. To delete a character before the cursor in the
text box.
:
Escape. To exit from the current interface or function.
:
Up & down. To switch the current selected list box.
:
Confirm. To c onfirm current operation.
FC-1 High-Performance Portable Platform Operation Manual
6
3 Function Description
3.1 Power On and Power Off
3.1.1 Power On
Press the button on the platform front panel. When you hear the
buzzer sounds, the boot screen appears, indicating that the platform is
powered on.
3.1.2 Power Off
When platform is working, press the button at the front panel on the
platform. The shutdown screen appears. Press button on the
shutdown screen or key. The shutdown screen disappears, and the
shutdown operation is cancel. Press
button on the shutdown screen
or
key. When you hear the buzzer sounds, the screen is off and the
platform is powered off.
When platform is working, press the
key at the front panel on the
platform for a long time (for more than 5 seconds). When you hear the
buzzer sounds, the screen is off, and the platform is directly powered
off.
3.2 Main Interface
After the FC-1 high-performance portable platform boot, enter the
Chinese main interface. The main interface includes four parts: a status
bar, an information panel, an application list area and a switch area.
FC-1 High-Performance Portable Platform Operation Manual
7
Figure 3.1 Main Interface
3.2.1 Status Bar
The status bar displays the current network connection status, U disk
and SD card status, time, battery power status, screenshot function
button and soft keyboard button.
Pressing the screenshot function button
on the status bar can
achieve the screenshot of the current graphics user interface. The
screenshot pictures save to the file as bmp format to store to the
platform "Documents" disk. The picture file with date and time of the
screenshot as a file name is stored in the folder with the current date as
its name.
Pressing the soft keyboard button
on the status bar can achieve the
soft keyboard to bring up and disappear.
Status Bar,
Information
Panel
Switch
Area
Application
List Area
FC-1 High-Performance Portable Platform Operation Manual
8
Time Soft keyboard Connet
Screenshot Battery
Figure 3.2 Status Bar
Table 3.1 Different Connection Status Icon
Battery Power Status Icon
Charging
Depletion
About 1/4 Power
About 1/2 Power
About 3/4 Power
Full Power
Table 3.2 Different Battery Power Status Icon
Yes
No
Network connet
U disk
SD card
FC-1 High-Performance Portable Platform Operation Manual
9
3.2.2 Information Panel
The information panel can switch the system language (Chinese or
English). It displays an analog clock, date and software version.
Figure 3.3 Information Panel
3.2.3 Application List Area
Application programs are arranged in the list area in two rows and three
columns. If they can not be released to the same page, the application
programs display in the next page. The page number block just below
indicate the current page. Horizontal slide touch screen in the area or
press the keys
and to switch the pages.
Figure 3.4 Program List Area
Language
Analog
Clock
Date
Version
FC-1 High-Performance Portable Platform Operation Manual
10
3.2.4 Switch Area
Press application icon to show platform application programs.
Press model icon to show platform model programs. Press the
application icon
/model icon or key to switch.
Figure 3.5 Switch Area
3.3 Platform Application Programs
3.3.1 Time
In the first page of application list area, press the icon . You can set
the date and time. Press ‘OK’ after the correct date and time is set,
shown as below:
Figure 3.6 Date and Time Setting
3.3.2 Net Setting
In the first page of application list area, press the icon . You can set
net configurations, including IP address, subnet mask, gateway IP
Date
Month
Time
FC-1 High-Performance Portable Platform Operation Manual
11
address, DNS IP address, and MAC address. Press ‘OK’ after the
correct net configurations is set, shown as below:
Figure 3.7 Net Setting
3.3.3 Web Browser
In the first page of application list area, press the icon to enter web
browser. Press
to exit web browser, shown as below:
Back/Forward Refresh Address Bar Search Bar
Figure 3.8 Web Browser
Tab
New Ta b
Status
Bar
FC-1 High-Performance Portable Platform Operation Manual
12
3.3.4 File Manager
In the first page of application list area, press the icon or key
at the front panel on the platform to open the file manager. The file
manager can copy, paste, delete, rename, create folder and etc., shown
as below:
Figure 3.9 File Manager
3.3.5 Application Manager
In the first page of application list area, press the icon to open the
application manager. You can add or update platform model programs.
When you add or update a model program, insert U disk or SD card
which stores the model program. Press the "Add new model" bottom of
list item, and then it turns to white. Press the "Add" button. The program
Note: 1. Make sure the platform communication RJ45 interface is
already connected to the network which can access the Internet via
a twisted pair.
2. Make sure the network settings are correct, specific see “3.3.2
Net Setting”.
FC-1 High-Performance Portable Platform Operation Manual
13
can identify all model programs existing in the U disk and the SD card
automatically, and displays them in a new pop-up list. Select the
desired model program, and press the ‘Install’ button to complete to add
or update the model program.
Figure 3.10 Application Manager
FC-1 High-Performance Portable Platform Operation Manual
14
3.3.6 Calibration
In the first page of application list area, press the icon to open the
calibration window. Using the touch screen pen press
appearing in
the screen. After completing the top left corner, top right corner, bottom
right corner, bottom left corner and the middle position of the touch
screen calibration, program returns to the main interface, and ‘Please
reboot to take effect!’ dialog box is pop-up. Press ‘reboot’ button. The
platform automatic reboots, and touch screen calibration is completed.
3.3.7 Picture Viewer
In the second page of the application list area, press the icon to
open the picture viewer, shown as below:
Note: 1. Make sure the U disk and SD card have stored the
necessary model program, and the U disk and SD card can be
accessed by the platform.
2. Do not remove the battery when you add or update model
programs.
3. Do not remove the U disk or SD card when you add or update
model programs.
4. In order to complete adding or updating model programs
successfully, it is recommended to use the AC adapter, and make
sure there is enough free flash memory space in the platform.
FC-1 High-Performance Portable Platform Operation Manual
15
Figure 3.11 Picture Viewer
3.3.8 Calculator
In the second page of application list area, press the icon to open
the calculator. Press botton or to exit the calculator, shown
as below:
Figure 3.12 Calculator
3.3.9 Disk
In the second page of the application list area, press the icon to
open the disk information viewer. It can show the used size and the
available size in the disk, shown as below:
FC-1 High-Performance Portable Platform Operation Manual
16
Figure 3.13 Disk Information
3.3.10 Update
In the second page of the application list area, press the icon to
open the update dialog box. You can upgrade the firmware or platform
program. Insert U disk or SD card which stores the upgrade program.
The platform will identify the upgrade program automatically. Press
firmware or platform list item, a confirmation dialog box is pop-up.
Entering the upgrade process, the platform restarts automatically after
the upgrade is completed.
Figure 3.14 Update
FC-1 High-Performance Portable Platform Operation Manual
17
3.3.11 About
In the second page of application list area, press the icon to open
the ‘about’ dialog box which shows current software version, shown as
below:
Figure 3.15 About
3.4 Soft Keyboard
Press key at the front panel on the platform or botton at the
status bar, and the soft keyboard is pop-up. Press ‘CN’ bottom to switch
Note: 1. Make sure the U disk and SD card have stored the
necessary update program, and the U disk and SD card can be
accessed by the platform.
2. Do not remove the battery when you update the platform.
3. Do not remove the U disk or SD card when you update the
platform.
4. In order to complete updating successfully, it is recommended to
use the AC adapter, and make sure there is enough free flash
memory space in the platform.
FC-1 High-Performance Portable Platform Operation Manual
18
to English input method. ‘CN’ bottom becomes ‘EN’. Press again to
switch to Chinese input method. ‘EN’ bottom becomes ‘CN’. Chinese
input method is Pinyin input method. Press number and character keys
from
to to select the word you need. Pressing key again,
the soft keyboard disappears, shown as below:
Figure 3.16 Soft Keyboard
3.5 LCD Brightness Adjustment
Press key at the front panel on the platform to open LCD backlight
brightness adjustment window. Press
and to adjust LCD
backlight brightness. This window will be disappear when stop
operation for 3 second.
Figure 3.17 LCD Brightness Adjustment
FC-1 High-Performance Portable Platform Operation Manual
19
3.6 Charging
When the battery is fully charged, the charge indicator light is green.
When the battery power is low, the charge indicator light turns to red.
You need to connect the AC adapter to the AC adapter jack on the
platform. The charge indicator light is flashing red when the battery is
being charged. The charge indicator light turns to green when battery is
already fully charged. It takes about 5 hours for full charging.
The platform will shutdown automatically when the battery power is low.
Note: 1.
The platform internal battery is a lithium battery. This
battery must be charged using a dedicated charger. Using other
charger will damage the platform. The platform can not be charged
exceed the temperature at 10℃ to 35℃ range, otherwise it will
affect battery life.
2. It is recommended to charge the platform in the power off status.
3. Low temperatures may cause a temporary decline in battery
capacity, but it will not cause damage to the battery.
4. When the operating time was significantly shorter than normal,
replace the battery.
FC-1 High-Performance Portable Platform Operation Manual
20
4 Appendix
Instrument Specifications
Specifications Range
Display 154.08mm*85.92mm（7inches）LCD
Display
Resolution
800*480 pixel
Working
Temperature
-10 ~ +50 ℃
Storage
Temperature
-20 ~ +60 ℃
Weight 1820g
Dimension 245mm*160mm*63mm
AC Adapter DC：12.0V━5A
Battery 7.4V，7500mAh
Battery
Charging Time
5 hours
Battery Working
Time
More than 8 hours
FC-1 High-Performance Portable Platform Operation Manual
21
Standard Accessories
Standard Accessories Number
Main Unit with Lithium-ion Battery 1
AC Adapter 1
Touch Screen Pen 1
Operation Manual 1
Portable Instrument Package 1
SD Card 1
Three-wire Power Cord (1.5m) 1
FC-1 High-Performance Portable Platform Operation Manual
22
Tianjin Deviser Electronics Instrument Co., Ltd.
Add: N0.8, Haitai Chuangxin 3
rd
Road, Hi-Tech Industrial Development
Area, Tianjin, China, 300392
Tel: +86-22-2764 5003 ext. 803
Fax: +86-22-2764 5002
http://www.deviserinstruments.com
E-Mail:
overseasbiz@deviser.com.cn
Loading...