PRO-USB1
Professional USB studio recording microphone
User manual
Any information and illustrations shown in this user manual are subject to change without further notice.
User manual version: 1.0 Creation date + author initials: 27-03-2014 RV Revision date + author initials: 27-03-2014 RV
Introduction
Thank you for purchasing this Devine PRO-USB1 broadcasting and recording microphone. Before you
unpack all the received items, carefully read this manual to become familiar with the functions of the
microphone. Also check the contents of the box to make sure all necessary parts are included. If the
microphone fails to operate properly, or if you have any problems while using it, disconnect it and contact
your local dealer for more information and help.
Any information and illustrations shown in this user manual are subject to change without further notice.
User manual version: 1.0 Creation date + author initials: 27-03-2014 RV Revision date + author initials: 27-03-2014 RV
Box contents
Box contents:
1x Devine PRO-USB1 microphone
1x shock mount
1x USB A – USB B cable
1x storage/transport case
Unit and accessory inspection
- If the unit is not going to be used for a longer period of time, disconnect it and store it in a dust-free
environment.
- Always check the unit for possible damage before use. If you suspect that something is wrong with the unit,
do not connect it! When you suspect that your unit is broken or damaged, contact your local dealer or a
certified technician to inspect the unit.
Note: Illustrations shown in this manual may vary from the actual product.
Any information and illustrations shown in this user manual are subject to change without further notice.
User manual version: 1.0 Creation date + author initials: 27-03-2014 RV Revision date + author initials: 27-03-2014 RV
Use of the microphone
The Devine Pro USB-1 studio microphone is suitable for most recording applications in your studio and has a
built-in high quality A/D converter. This way, the microphone can be connected to a computer or laptop
without having to use additional hardware.
A/D conversion and USB connection:
The Devine Pro USB-1 is equipped with an internal A/D converter, which tranfers the analogue microphone
signal to a digital signal which can be interpreted by a computer. Through USB it is possible to connect the
microphone directly with your computer, the length of the included cable is approximately 3 meters.
First time connection:
The Devine Pro USB-1 is plug-and-play compatible, which means that it will install the proper drivers
automatically after you connect the microphone through USB. When connecting the microphone, you should
receive a system message that a new USB-device is found and that the system will search automatically for
the correct drivers. After these are installed, a message should pop up which confirms that the installation
was successful and that your microphone is ready to use.
The Pro USB-1 can be used with almost every recording software available. For starters, Devine
recommends the free available open-source software Audacity. This software works with Windows, Mac and
GNU/Linux. For more information, visit the download page: http://audacity.sourceforge.net/?lang=nl
Protect your microphone:
This Devine microphone is equipped with very sensitive electronics to provide optimal audio performance.
Make sure the microphone is not exposed to severe shocks, collision, drops from high altitude or any
situations that may cause permanent damage. Improper use of the microphone is not covered by warranty.
Always transport the microphone in the original package, or in a flightcase with proper foam inlay. The
microphone is not intended for on-the-road use.
Positioning your microphone
The Devine USB PRO-1 comes with an included shock mount, which reduces background and handling
noise. This shockmount is also the perfect accessory to mount the Pro USB-1 on a microphone stand. Make
sure to tighten the knobs on your stand properly and place the microphone as close to the audio source as
possible.
Placement on a microphone stand or boom arm
The shockmount of the BM-500 microphone is equipped with a 5/8” thread, suitable for most microphone
stands. If your microphone stand has 3/8” thread, adapters can be purchased separately. For easy
positioning, mount the shockmount with the thread mount before mounting the microphone.
Any information and illustrations shown in this user manual are subject to change without further notice.
User manual version: 1.0 Creation date + author initials: 27-03-2014 RV Revision date + author initials: 27-03-2014 RV
Troubleshooting
Problem Possible Cause Solution
No sound, or very low sound
signal
Volume set too low in settings Increase incoming volume and
gain on your mixer, interface or
other sound processing device
Microphone positioned too far
away
Place the microphone closer to the
sound source
Rattling and cracking sounds Moist inside the microphone Let the microphone dry on room
temperature and avoid use of the
microphone in humid or moist
environments. Do not let the
microphone come in contact with
water or liquids.
Loud high frequencies coming
from the speakers
Microphone positioned too close to
the speakers, which causes
feedback
Move the microphone further away
from the speakers, or change the
position to prevent the microphone
to be aimed directly at the
speakers.
Interruptance of the microphone
signal
Loose cable or broken cable Check if the cable is plugged into
the microphone correctly. If that
does not solve the problem, try to
change the cable.
Distortion and/or noise in the
captured sound
Too much airflow caused by vocal
airflows
Use a pop filter (sold separately)
Too much airflow caused by wind
(outdoor use)
Use the windscreen (included)
Any information and illustrations shown in this user manual are subject to change without further notice.
User manual version: 1.0 Creation date + author initials: 27-03-2014 RV Revision date + author initials: 27-03-2014 RV
Technical specifications
- USB studio microphone
- A/D conversion: 16-bit, 48 kHz
- USB plug and play
- suitable for vocal and instrument recording
- works with every recording software or DAW (e.g. Audacity)
- polar pattern: cardioid
- electret condenser microphone
- frequency response: 20 Hz – 18 kHz
- diaphragm thickness: 2 micron
- connector: USB B (cable included)
- included shock mount
- shock mount reduces unwanted noise
- padded microphone holder, prevents scratches
- angle adjustable
- 5/8” thread
- USB cable included
- cable length: 3 meters
Frequency response graph:
Any information and illustrations shown in this user manual are subject to change without further notice.
User manual version: 1.0 Creation date + author initials: 27-03-2014 RV Revision date + author initials: 27-03-2014 RV
Loading...