DeView D410-THRE3V12L, D410-THRE3V12LHTR, D410-THRN3V12L, D410-THRN3V12LHTR Instruction Manual

COLOUR VANDAL PROOF CAMERA

D410-THRE3V12L / D410-THRN3V12L
D410-THRE3V12LHTR / D410-THRN3V12LHTR

Dimensions : mm

INSTRUCTION MANUAL

■ Do not open or modify
Do not open the cabinet exit during maintenance and
installation, as it may be dangerous and cause damages.

■ Do not put objects inside the unit
Make sure that no metal objects or flammable substances
get insdie the camera. It could cause fire, short-circuits or
damages.

■ Be careful when handling the unit
To prevent damage, do not drop the camera or subject
it to strong shock or vibration.

■ Install away from electric or magnetic fields

■ Protect from humidity and dust

■ Protect from high temperature

Be careful when installing close to the ceiling , in a kitchen
or boiler room, as the temperature may raise to high levels.

■ Cleaning
Dirt can be removed from the cabinet only by wiping it
with a soft cloth moistened with a soft detergent solution.

■ Mounting Surface
The mounting surface material must be strong enough to
secure the camera.

■ Ingress Protection
Ensure all cable entry points are sealed with silicone sealent

About this Manual

Before installing and using the camera, please read this manual carefully.
Be sure to keep it handy for later reference.

PRECAUTIONS

■ CONNECTIONS

to prevent moisture ingress.

TROUBLESHOOTING

Before sending the camera out for repair, check the items
below. If the problem persists after checking these items,
contact your service center.

■ If no image appears

Is the coaxial cable attached securely?
Are the power and voltage normal?
Has the iris of the lens inside the camera been
adjusted correctly (with the level volume) ?
Is there adequate illumination?

■ If the image is unclear

Is the lens in focus?
Is the lens dirty?
Dirt of fingerprints on the lens can adversely affect the
images. Gently wipe any dirt or fingerprints off the lens
with a soft cloth or lens cleaning paper and cleaning
fluid (commercially available).
Is the monitor adjusted correctly?

WARNING:
TO PREVENT THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS APPLIANCE TO
RAIN OR MOISTURE. ENSURE ALL CABLE

CAUTION :

Check for polarity when using a DC 12V or AC 24V power supply.

CONNECTOR AND CAMERA SETTING

DC12V / AC24V

DC12V / AC24V

ENTRY POINTS ARE SEALED

TO PREVENT

MOISTURE INGRESS

■ LENS ADJUSTMENTS

Rotation 360˚

■ CAMERA SETTINGS

● OSD SWITCH FUNCTION

Rotation 360˚ Tilt 70˚

1. Adjust the panning(360˚), rotation (360°) and tilt(70˚)
position.

2. Set the zoom position using the Zoom Lever Screw.

3. Set the focus using the Focus Lever Screw.

CONNECTIONS AND CAMERA SETTINGS

Focus

Zoom

Loosen grub screw for rotation of camera
module using the small allen key

OSD

SETUP

FUNTION

SUMMARY

when using BUILT-IN lens, selecting

MANUAL will allow the aperture to be fixed

SHUTTER

ESC, MANUAL, FLK, OFF

MANUAL: 1/60(50) ~ 1/120,000sec, x2~ x128

WHITE BAL.

ATW, MANUAL, AWC

ATW: 1,800 ~10,500 ˚K

BACKLIGHT

OFF, LOW, MIDDLE, HIGH

Backlight compensation

AGC

NORMAL, HIGH,OFF

the Brightness can be adjusted(1 ~ 70)

DNR

MIDDLE, HIGH, OFF, LOW

when AGC is turned off, DNR does not operate.

SENS-UP

AUTO(=X6), OFF

when AGC is turned off, SENS-UP does not
operate.

SPECIAL Refer to the section below

EXIT Save the settings then exit

SPECIAL FUNTION SUMMARY

OFF, uppercase or lowercase, maximum length for the name

/numeral 0~9/-, null display is limited 15 characters

AUTO :

daytime → colour mode ,

night-time→ B/W mode

B/W : Always in B/W mode

COLOUR: Always colour mode

EXTERN : CDS EXTERNAL SIGNAL INPUT

SYNC

INT, LL (n/a for 12VDC model)

LL mode: you can adjust desired phase from 0˚
~ 359˚, auto detection

MOTION DETECTION

OFF, ON

ON mode: AREA (4 programmable zones
/SIZE), the words 'MOTION DETECTED"
appear on the screen when movement is

PRIVACY

OFF, ON

ON mode:AREA(4x programmable zones)
/SIZE/TONE

MIRROR

OFF, ON

set a horizontal image inversion.

CAMERA ID

DAY NIGHT

AUTO, B/W, EXTERN, COLOR

LENS

DC(=25), MANUAL

SHARPNESS

OFF, ON(=8)

the available range of level is 0 ~ 31.

RESET Reset all settings to factory defaults

RETURN save the SPECIAL MENU and then return to the

SETUP MENU

SPECIFICATION

MODEL

General Spec NTSC PAL

CCD Type

1/3" 410K Pixels Color 1/3" 470k Pixels Color

Total number of pixels 811(H) X 508 (V) 795(H) X 596(V)

Min illumination

Video Output

Resolution

S/N Ratio

Shutter speed x128 : 1/60~1/120,000sec x128 : 1/50~1/120,000sec

Sync System

White Balance

OSD

Built-in

DAY / NIGHT

AUTO / B/W / COLOR

DNR LOW, MIDDLE, HIGHT,OFF

Power Input

Video Output

Voltage

Power Consumption

Lens

Dimension

Weight

Case Color

Operation temp

-10Ԩ׽ +55 Ԩ

900g

Ivory

Max [DC12V : 5.7 W, AC24V : 5.3 W, with Heater DC12V : 18W , AC24V :
12W]

Mechanical Spec

3.3~12.0 mm

140(ø) X 105(H)mm

Wire

BNC Cable

Electric Spec

DC 12V(10 - 20V) or AC24V(20 - 28V)

50dB (AGC off, weight ON)

Internal / External

ATW/AWC/MANUAL (1800 ˚K ~ 10,500 ˚K)

Connector

D410-THRN3V12L (+HTR) / D410-THRE3V12L (+HTR)

0.3 Lux/F1.2(50 IRE, AGC HIGH, DNR HIGH)

1.0Vp-p/75 ohm Composite

520 TV Lines(Min)

Models e

quipp

ed with heater: -40°C ~ +55°C

INSTALLATION

1. Use the supplied L-wrench to remove the four fixing
screws (B) of dome cover (A).

2. Align the camera unit with the surface of the ceiling,
make marks on the ceiling in the places where the screw
holes are to be drilled, and then drill the four holes.

3. Cut a hole (diameter2.9in.73mm) in the ceiling for routing
the cables.

4. Pass the power cable (E) and video cable (F) from the
camera unit through the cable hole in the ceiling.

5. Align the four screw holes in the camera unit (D) with
the screw holes in the ceiling, and then secure the
camera in place by tightening the four or more screws
(C) through the washers. Remember to use the base
gasket.

6. Carry out the settings and adjustments for the camera.

7. Ensure all cable entry points (rear or side) are sealed
with silicone sealent to prevent moisture ingress.
Failure to observe this may result in condensation

In storage temp

Operation humidity

-20

Ԩ׽ +70

Ԩ

Under 90％(Non-condensing)

qpp

A

D

C

E F

deposits that will reduce the IR response of the camera

.

8. Secure the dome cover (A) by tightening the screws (B).

B