Deublin 17/21 Series, 2117 Series, 1690 Series, 1790 Series, 1379 Series Operating Manual

040-563
2018-10

Operating Manual

Model/Series:
Number: GB
Version:

Rev. D Page 1 of 16 ©DEUBLIN

for air and hydraulic
with elastomeric seals

Rotating Unions

Series

17/21, 2117, 1690, 1790, 1890, 1379, 1479, 2300, D, MPSS-000037

for air and hydraulic

with elastomeric seals

OPERATING MANUAL

040-563
2018-10

Operating Manual

Model/Series:
Number: GB
Version:

Rev. D Page 2 of 16 ©DEUBLIN

for air and hydraulic
with elastomeric seals

Content

1 For your Safety ________________________________________________________________ 3

1.1 Intended Use __________________________________________________________________ 3

1.1.1 Application cylinder (Duo) _______________________________________________________ 4

1.2 Misuse ________________________________________________________________________ 4

1.3 Safety Instructions ______________________________________________________________ 5

1.3.1 Hazards due to hot surfaces _____________________________________________________ 5

1.3.2 Hazards due to incorrect hoses __________________________________________________ 5

1.3.3 Hazards due to the media _______________________________________________________ 5

1.3.4 Hazards by faulty installation _____________________________________________________ 6

1.4 Structure of Pictograms _________________________________________________________ 7

2 Information as to this Manual ___________________________________________________7

3 Information on the Name Plate __________________________________________________7

4 Information on the Design ______________________________________________________ 8

4.1 Filtering of the Medium __________________________________________________________ 8

4.2 Compressed Air Purity Classes ___________________________________________________ 8

4.3 Definition of Hydraulic Fluids _____________________________________________________ 9

4.4 Optional 1379/1479: use of support sleeves for vacuum applications _________________ 9

4.5 Connecting Options of the Rotating Union at the Machine Shaft ______________________ 9

4.6 Options of Hose Installation ____________________________________________________ 10

4.6.1 Connection of hose to the rotating union _________________________________________ 10

4.6.2 Observe the “paired” connection of the medium ___________________________________ 10

4.6.3 Using an anti-rotation element __________________________________________________ 11

4.6.4 Optional: Connection of a leakage line ___________________________________________ 11

5 Installation ___________________________________________________________________ 12

6 Information on the Operation ___________________________________________________ 12

7 Storage _____________________________________________________________________ 12

8 Maintenance _________________________________________________________________ 12

8.1 Maintenance Intervals __________________________________________________________ 12

8.2 Daily Inspection _______________________________________________________________ 13

9 Trouble Shooting _____________________________________________________________ 13

9.1 Potential Causes for Errors and their Elimination ___________________________________ 13

9.2 Pack Rotating Union for Transport _______________________________________________ 14

10 Disposal_____________________________________________________________________ 15

10.1 Dispose of Packaging __________________________________________________________ 15

10.2 Dispose of Rotating Union ______________________________________________________ 15

11 Spare Parts __________________________________________________________________ 15

040-563
2018-10

Operating Manual

Model/Series:
Number: GB
Version:

Rev. D Page 3 of 16 ©DEUBLIN

for air and hydraulic
with elastomeric seals

1 For your Safety

This chapter provides information on the safe handling of DEUBLIN rotating unions.

❑ For your own safety and the safety of other people read this operating manual carefully and

completely prior to working on or with DEUBLIN rotating unions.

❑ This operating manual exclusively describes the rotating unions of the manufacturer DEUBLIN.

In the further description/explanation the name “DEUBLIN” is left out for a better readability.

❑ This operating manual is a material part of the specified rotating unions. The operator is re-

sponsible for the personnel to take note of this manual.
❑ Always use the latest version of the operating manual, available under www.deublin.eu.
❑ The operator of the rotating unions shall not make any modifications or attachments to and

retrofitting of the rotating union without the manufacturer’s consent.
❑ Please follow the additional instruction „Installation“ for a secure and correct installation of the

rotating union. The installation instruction is included with the delivered union.

1.1 Intended Use

The rotating unions of the series 17/21, 2117, 1690/1790/1890, 1379/1479, 2300, D and MPSS-000037
are suitable for the following media:

Series

Medium

(1)

Air Water Hydraulic oil Brake fluid Vacuum

17/21/2117 • • • •

1690

• • •1790
1890
1379

• • •
1479

2300 •

D • •

MPSS-000037

• •

(1)

In order to obtain the longest possible lifetime for rotating unions, the applied medium must meet

certain requirements, which are defined in chapter 4.2.

The rotating unions put the medium under a certain pressure forcing it through the rotating machine
components (e.g. machine shaft) to the load.

The rotating unions referred to are designed for non-potentially explosive environments and non­combustible media.

Details on the operating range of the rotating unions are provided in the catalogue and/or the model­specific installation drawing.

The rotating unions of the series 17/21, 2117, 1690/1790/1890, 1379/1479 , 2300, D and MPSS-000037
can be used as single-passage or multi-passage option, depending on the number of connections.

040-563
2018-10

Operating Manual

Model/Series:
Number: GB
Version:

Rev. D Page 4 of 16 ©DEUBLIN

for air and hydraulic
with elastomeric seals

1.1.1 Application cylinder (Duo)

The following application is one example from a variety of applications.
This example shows how the cylinder is supplied with hydraulic oil or compressed air as medium.

Fig. 1: Schematic diagram showing the power transmission to the cylinder

The hydraulic oil moves the piston of the cylinder. The mating connections of the rotating union are
thereby used in pairs.

❑ In order to extend the piston, the hydraulic oil is supplied through connection P1 of the rotating

union in front of the piston. P2 is un-pressurised.

❑ In order to retract the piston, the hydraulic oil is supplied through connection P2 of the rotating

union behind the piston. P1 is un-pressurised.

Depending on the complexity of each application, the corresponding series with the required number
of connections and channels can be used.

1.2 Misuse

This chapter provides information on known misuse of rotating unions of the 17/21, 2117, 16 90 /17 90 /18 90,
1379/1479, 2300, D and MPSS-000037 series.
The rotating unions are not suitable for the areas and applications described herein. Use in such ar­eas or for such applications constitutes a misuse endangering people and machines and is therefore
prohibited. Always observe the operating data released by DEUBLIN on the model-specific drawing. It
can be requested from DEUBLIN.

Prohibition for the following areas:

❑ Potentially explosive areas

The rotating unions of the 17/21, 2117, 1690/1790/1890, 1379/1479, 2300, D and MPSS-000037

series shall not be used in potentially explosive areas, as they are not approved for the require­ments in potentially explosive areas. Operation in such areas may cause explosions.

❑ Outdoor operation

Inadequate protection against weather conditions can result in premature failure.

Prohibition for the following applications:

❑ Conveying of combustible media or hydrocarbons

Combustible media or hydrocarbons may ignite or cause explosions.

Exception: Thermal oil within the admissible temperature range. Please observe the safety
data sheet of the used thermal oil.

❑ Food

Food, cleaning and disinfectant residues cannot be removed from the rotating unions. People

may suffer poisoning.

P1

P2

040-563
2018-10

Operating Manual

Model/Series:
Number: GB
Version:

Rev. D Page 5 of 16 ©DEUBLIN

for air and hydraulic
with elastomeric seals

❑ Connection to a piping system with excessive pressure

If excessive pressure is applied to the rotating unions, supply pipes can come off and cause

personal injury or property damage.

❑ Connection to fixed pipes

If connection is via fixed pipes, the rotating unions may leak and the ball bearings may get

damaged.

❑ Conveying of media which are too hot

If the media exceed the maximum admissible temperature for the rotating union, the seals can

be damaged which may result in leaky rotating unions and personal injury or property damage.

❑ Application in ambient temperatures/with media temperatures below 3 °C

Rotating unions may be damaged if they are operated at temperatures (ambient or media) be-

low 3 °C.

❑ Operation without a medium (dry run)

If the rotating unions are operated without a medium, the sealing surface of the rotating unions

might fail prematurely.

❑ Operation at maximum speed and with maximum pressure

Speed and pressure must be adjusted to each another so that the rotating unions are not dam-

aged or fail prematurely (see model-specific installation drawing).

This list is not comprehensive and will be updated with results from product observation.

1.3 Safety Instructions

This chapter provides information on the hazards when using rotating unions.

1. 3.1 Hazards due to hot surfaces

Frictional heat and the temperature of the medium causes rotating unions to rise in temperature. Skin
contact with heated rotating unions can cause injuries.

❑ Use safety gloves and PPE (Personal Protective Equipment) protecting against heat when han-

dling the rotating union.

❑ Attach a clearly visible danger sign visibly on/next to the rotating union in order to warn of

danger.

1.3.2 Hazards due to incorrect hoses

For the connection of the rotating union to the machine, you have to choose appropriate hoses for the
respective medium, which meet, the specifications for the application.
If you use incorrect hoses, they may become porous or burst. This can cause personal injury and/or
property damage to components of the machine.

❑ Use only hoses which are suitable for the media, the maximum system pressure and the maxi-

mum temperature for the machine.

1.3.3 Hazards due to the media

When working on the rotating union, injuries can be caused by skin or eye contact with the media.

❑ Observe the safety instructions for the flow media. Observe the COSHH Safety Data Sheet for

the flow media.

040-563
2018-10

Operating Manual

Model/Series:
Number: GB
Version:

Rev. D Page 6 of 16 ©DEUBLIN

for air and hydraulic
with elastomeric seals

1.3.4 Hazards by faulty installation

If the rotating unions are installed incorrectly, hoses and connections may become leaky. The medium
can escape. Depending on the medium, personal injury or property damage to the components of the
machine may occur.

❑ Before installing the rotating union ensure that no feed pressure and no residual pressure is

applied to the pipeline system of the machine.

- Please follow the additional instruction “Installation” for a secure and correct installation of
the rotating union. The installation instruction is included with the delivered union.

❑ Install the hoses to the rotating union prior to mounting it at the machine shaft. This does not

apply to hoses with an SAE connection.
❑ Install the anti-rotation element on the rotating union, tension free.
❑ Make sure that the hoses are connected in compliance with the channel configuration of the

rotating union. Pay attention to the model specific installation drawing.
❑ Install the rotating union on the machine using hoses only, in order to avoid stress on the rotat-

ing union.
❑ Install the hoses free from stress.
❑ Rotating Unions with leakage line: Install the rotating union in a way that the leaking medium

can be carried away securely downward at the lowest point and that the drain line shows a fall

(min. 15°).

040-563
2018-10

Operating Manual

Model/Series:
Number: GB
Version:

Rev. D Page 7 of 16 ©DEUBLIN

for air and hydraulic
with elastomeric seals

1.4 Structure of Pictograms

This chapter provides information on the meaning of the pictograms used in the manual.

Warning

Potentially dangerous situation, which may result in death or serious injury.

Note

Potentially harmful situation in which the product or surrounding objects can be dam­aged.

Application notes
and other useful information.

2 Information as to this Manual

The copyright as to this manual remains with DEUBLIN. Subject to changes!

❑ You can download the latest version of this manual under www.deublin.eu.
❑ Always use the latest version of the operating manual.

3 Information on the Name Plate

Model number

DEUBLIN‘s internal identification / date of manufacture

MADE IN <<country of manufacture>>

Fig. 2: Name plate

The coding of the model number is described in the catalogue. The model number corresponds to the
order number.

Warning

Note

Info

040-563
2018-10

Operating Manual

Model/Series:
Number: GB
Version:

Rev. D Page 8 of 16 ©DEUBLIN

for air and hydraulic
with elastomeric seals

4 Information on the Design

This chapter provides information as to which items have to be observed in the design in order to have
a positive effect on the service life of the rotating union.

You can obtain the drawings of the rotating unions from DEUBLIN to integrate the ro­tating union in your drawing.
You will require the model-specific installation drawing of your rotating unions to imple­ment it into your design and to operate the rotating unions in a safe manner.

The model-specific installation drawing of the respective rotating union contains e.g.:

❑ torque moments of the union
❑ technical data
❑ tolerances
❑ approved media

4.1 Filtering of the Medium

Unfiltered media with a particle size of more than 60 µm, increased wear of the rotating union.

Please use the following classes of liquid media:

❑ Class 5 in accordance with ISO 4406:2017 Code 17/15/12 or
❑ Class 6 in accordance with NAS 1638

Determine the required filter performance data according to standard ISO 16889:2008 to achieve a
maxi-mum particle size of 60μm.

The larger the particles in the media, the higher the wear of the rotating union is. The
higher the total of all particles (polluting load), the higher the wear.

❑ Insert a filter in front of the rotating union which filters particles with a size of 60 µm and larger

from the media.

4.2 Compressed Air Purity Classes

This chapter only applies for series 17/21, 1217, 1690/1790/1890 and MPSS-000037.

To ensure the longest possible service life of the rotating union, DEUBLIN recommends using a com­pressed air purity class according to ISO 8573-1:2010 [6:4:4]. This results in the following parameters
for the compressed air:

Particles Water Oil

Mass concentration

Cp [mg/m³]

Pressure dewpoint

[C°]

Concentration of total oil

[mg/m³]

0 < Cp ≤ 5 ≤ +3 ≤ 5

Info

Info

Info

040-563
2018-10

Operating Manual

Model/Series:
Number: GB
Version:

Rev. D Page 9 of 16 ©DEUBLIN

for air and hydraulic
with elastomeric seals

4.3 Definition of Hydraulic Fluids

The hydraulic fluid that is used must correspond to the following definition: Mineral oils according to
DIN 51524 (HL; HLP)/ ISO 6743/4 (HL, HM, HV) in viscosity classes 10, 22, 32, 46, 68 and 100 mm²/s).

4.4 Optional 1379/1479: use of support sleeves for vacuum applications

For vacuum applications of series 1379/1479, support sleeves are used for the connections to the
flange. These support sleeves prevent the O-rings from being drawn into the channel in the event of a
vacuum which would cause the rotating unions to leak.
Support sleeves and installation instructions are supplied together with the rotating unions of series
1379 and 1479.

Component damage due to incorrect installation

If the support sleeves are inserted into the channel with O-ring already in position, you
risk crimping and damaging the O-rings.

❑ Remove the O-rings, insert the support sleeves, and then insert the O-rings.

4.5 Connecting Options of the Rotating Union at the Machine Shaft

Fig. 3: Options for the installation on the machine shaft

The rotating unions are mounted to the machine shaft via the rotor. The following rotor options are
available:

❑ Option (A): The rotor is equipped with a flange.
❑ Option (B): The end of the rotor is threaded.

The rotor provides the connection between rotating union and shaft. Therefore it is important to care­fully design the shaft in compliance with the specifications in the installation drawing for each specific
rotating union. Deviations might result in leakages and uneven movements of the rotating unions.

Note

BA

040-563
2018-10

Operating Manual

Model/Series:
Number: GB
Version:

Rev. D Page 10 of 16 ©DEUBLIN

for air and hydraulic
with elastomeric seals

4.6 Options of Hose Installation

The following examples show how to install the hoses at the rotating unions.
These connecting options ensure that the hoses do not transfer stress to the rotating unions when the
machine shaft moves.

❑ Please pay attention to the chapter “1.3 Safety Instructions” regarding the design.

4.6.1 Connection of hose to the rotating union

The hoses must be installed without stress and bends so that they do not apply any forces to the rotat­ing union. The following figures show examples of installation.

Connect the rotating union with flexible hoses.
During operation, flexible hoses prevent lateral loads on the
bearings of the rotating unions.
Please observe chapter 1.3.4.

Fig. 4: Lateral connection of the hoses

4.6.2 Observe the “paired” connection of the medium

The connections for the rotating unions are arranged in “paired” connections, which are separately
sealed. In order to prevent the mixing of different media, you must be sure to supply and return only
one medium through “paired” connections.

Possible “paired” connections:

❑ Connection 1 and 2
❑ Connection 3 and 4

For rotating unions with further connections, the “paired”
connections are arranged in the same way.

Fig. 5: Example of “paired” connections

1

2

3

4

040-563
2018-10

Operating Manual

Model/Series:
Number: GB
Version:

Rev. D Page 11 of 16 ©DEUBLIN

for air and hydraulic
with elastomeric seals

4.6.3 Using an anti-rotation element

Fig. 6: Example of an anti-rotation element

The rotating union must be secured against rotation during operation using an anti-rotation element
(2). The connections of the hoses (1) can be used as torque supports.
A fork head may e.g. be installed on-site to serve as an anti-rotation element at a hose connection.

The connector of the hose (1) may in this example only touch
against one side of the bracket (2) of the anti-rotation ele­ment so that a clearance (X) remains between the other side
of the bracket and the hose connector.

Fig. 7: Top view torque support

4.6.4 Optional: Connection of a leakage line

To prevent surrounding components from being damaged by escaping medium, you can connect a
leakage line to some rotating unions with separate leakage line, if required.

Some rotating unions are provided with relief bores (leakage
connections) for ventilation and leakage discharge.

❑ When used in dirty environment, we recommend protect-

ing the leakage holes against penetrating dirt. If you close
all relief bores, pressure builds up resulting in the prema­ture wearing out of seals.

❑ Position the rotating union in a way that you can always

connect the leakage line in 6 o’clock position (at the lowest
point) to a leakage hole.

❑ The leaking medium has to be conveyed pressureless

back to the tank.

Fig. 8: Schedule connection of leakage line

1

2

x

2

1

040-563
2018-10

Operating Manual

Model/Series:
Number: GB
Version:

Rev. D Page 12 of 16 ©DEUBLIN

for air and hydraulic
with elastomeric seals

5 Installation

The union installation is described in an additional manual which is supplied with each rotating union.
Please follow the additional instruction “Installation” for a secure and correct installation of the rotating
union. The instruction “Installation” is available online under www.deublin.eu.

❑ Ensure that the person installing the rotating union receives the following information:

- Position and location of the rotating union in the machine

- Information on the media

- Plan for connection of hoses

- Position of leakage line

- Information on how to mount an anti-rotation element provided by the customer

- Installation drawing for each specific model

6 Information on the Operation

Damage to components due to operation without medium (dry running)

If your rotating union model is intended for operation with a medium but it is operated
without the medium, the sealing surfaces of the rotating unions will be damaged.

❑ Ensure that the rotating unions are operated with a medium.
❑ Switch off the plant/machine, if the rotating unions are operated without medium.

7 Storage

Damage of component due to incorrect storage

If you store the rotating unions incorrectly, they become leaky or get damaged.

❑ Store the rotating unions in a dry space between 3 °C and 40 °C.
❑ Rotating unions should not be stored for more than two years.

8 Maintenance

This chapter provides information on how to extend the service life of the rotating unions by means of
maintenance.

8.1 Maintenance Intervals

You can avoid early wear of the rotating unions, if you adhere to the maintenance intervals described
herein.

Risk of injury due to hot surfaces

Frictional heat and the temperature of the medium causes rotating unions to rise in
temperature. Skin contact with heated rotating unions can cause injuries.

❑ Before starting to work on the rotating union, allow the machine to cool down.
❑ Use safety gloves and PPE (Personal Protective Equipment) protecting against heat

or cold depending on the application of the rotating unions.

Re-lubrication is not necessary.

Note

Note

Warning

Info

040-563
2018-10

Operating Manual

Model/Series:
Number: GB
Version:

Rev. D Page 13 of 16 ©DEUBLIN

for air and hydraulic
with elastomeric seals

8.2 Daily Inspection

Check the rotating unions for tightness.

Risk of injuries due to applied line pressure

If you have to work on the rotating union and feed pressure of the medium is applied
or there is residual pressure in the piping system of the machine, the medium can es­cape under pressure when releasing the connections. You and other people may suffer
severe injuries.

❑ Ensure that no feed pressure is applied.
❑ Ensure that there is no residual pressure in the piping system.

During the operation of the machine, leakage might occur,
the time period is subject to the extent which the rotating
unions are used.

❑ Carry out daily visual inspections in order to check whether

leakage occurred at the rotating union (see arrows).

If you detect leakage:

1. Stop the machine.

2. Replace worn out or leaking rotating unions with new ro­tating unions.

3. Replace defective hoses with new hoses.

4. Seal leaking connections.

9 Trouble Shooting

This chapter provides the following information:

1. Which problem may occur?

2. What could be the cause of the problem?

3. How can you eliminate this problem?

Do not disassemble the rotating unions for repair. This invalidates the warranty claim.

9.1 Potential Causes for Errors and their Elimination

Risk of injuries due to applied line pressure

If you have to work on the rotating union and feed pressure of the medium is applied or
there is residual pressure in the piping system of the machine, the medium can escape
under pressure when releasing the connections. You and other people may suffer seri­ous injuries.

❑ Ensure that no feed pressure is applied.
❑ Ensure that there is no residual pressure in the piping system.

Warning

Fig. 9: Inspect visually

Info

Warning

040-563
2018-10

Operating Manual

Model/Series:
Number: GB
Version:

Rev. D Page 14 of 16 ©DEUBLIN

for air and hydraulic
with elastomeric seals

Error Potential causes Elimination

Rotating union is
leaky after installation

Incorrect installation 1. Stop the machine.

2. Ensure that the connections are sealed ac­cording to the manual “Installation”.

3. Ensure that all hoses are installed without
stress.

4. Ensure that all seal faces are clean.

5. Ensure that the anti-rotation element is
installed without stress.

Seal faces of the rotating
union are damaged

1. Pack rotating union.

2. Send rotating union to DEUBLIN for over-
haul/service.

Rotating union leaks
before the end of the
expected service life

Medium is contaminated 1. Stop the machine.

2. Drain medium.

3. Send rotating union to DEUBLIN for over­haul/service, if required.

4. Flush the piping system of the machine.

5. Mount new filter.

6. Fill in new medium.

Rotating union is not de­signed for the respective
application

1. Ensure that the correct DEUBLIN Rotating
Union is used.

2. Contact DEUBLIN if required.

Rotating union runs
untrue or wobbles

Thread and/or concen­tricity outside the admis­sible tolerance.

1. Stop the machine.

2. Remove rotating union.

3. Manufacture new thread or flange.

4. Mount the rotating union according to in­stallation instructions.

Rotating union is mount­ed incorrectly.

1. Stop the machine.

2. Remove rotating union.

3. Mount the rotating union according to in­stallation instructions.

9.2 Pack Rotating Union for Transport

The rotating union has to be protected against mechanical impact and humidity during transport to
ensure that the rotating union will arrive at DEUBLIN without being damaged.

1. Dismount the rotating union in reverse order of the installation (see Installation).

2. Ensure that the rotating union is free from the respective media.

3. Use a cardboard box, which is suitable for the weight of the rotating union.

4. Cushion the base of the cardboard box with a soft material, e.g. air bubble film.

5. Wrap the rotating union with a soft material, e.g. air bubble film.

6. Ensure that no packing material or dirt can penetrate the opening of the rotating union.

7. Position the rotating union in the middle of the cardboard box.

8. Fill the free space around the rotating union with newspaper or another suitable material.

9. Close the cardboard box by means of tape.

040-563
2018-10

Operating Manual

Model/Series:
Number: GB
Version:

Rev. D Page 15 of 16 ©DEUBLIN

for air and hydraulic
with elastomeric seals

10 Disposal

10 .1 Dispose of Packaging

❑ Dispose of the packaging (cardboard box and plastics) according to the national standards,

regulations and directives.

10.2 Dispose of Rotating Union

Mainly, the rotating unions consist of metals, which can be reused within the reclamation of scrap.
Decontaminate unions / parts and dispose of in an “Environmentally Friendly” way.

❑ Dismount the rotating union in reverse order to the installation (see Installation).
❑ Flush the rotating union.
❑ Collect the dirty flushing media.
❑ Dispose of the collected flushing media according to the national standards, regulations and

directives.
❑ Observe the instructions of the producer of the media.
❑ Dispose of the rotating union according to the national standards, regulations and directives.

In case of repair, DEUBLIN disposes of all used parts.

11 Spare Parts

The rotating unions have a limited service life and include wearing parts. All static and dynamic sealing
elements of a component are considered wearing parts, as well as ball bearings.

Repair kits are available for series 17/21, 2117, 1690/1790/1890 and 1379/1479, 2300 of the rotating
unions and can be obtained from DEUBLIN. No repair kits are available for models of the D and MPSS­000037 series. Please ask your DEUBLIN Service.
You need special tools and repair instructions for repair of the rotating unions, which can be obtained
from DEUBLIN as well.

Note

If you do not want to repair your rotating union on your own, DEUBLIN will be pleased
to help you. If requested, DEUBLIN will exchange all wearing parts and clean all com­ponents of the rotating union. Before repaired rotating unions leave the premises, they
will be subjected to an operational check. The repaired rotating union is returned with
a standard “DEUBLIN Warranty” valid for 12 months.

Info

©2018 DEUBLIN GmbH | Florenz-Allee 1 | 55129 Mainz | Alle Rechte vorbehalten.

Reliability

Many years’ experience, ongoing liaison with customers, innovations sourced

inhouse and from suppliers place DEUBLIN in a position providing

reliable Rotating Unions at the highest level.

When it comes to concrete applications, maximum service life is guaranteed

by matching the sealing to the respective medium.

The service life is also equally maximized by maintaining cleanliness when

storing and handling the Rotating Union and by adhering to the guidelines issued

by DEUBLIN in respect of the conditions on the customer’s premises.

AMERICA

EUROPE

DEUBLIN Germany

Florenz-Allee 1
55129 Mainz, Germany
Phone: [phone]
Fax: [phone]
e-mail: [e-mail]

DEUBLIN Italy

Via Guido Rossa 9 - Loc. Monteveglio
40053 Comune di Valsamoggia (BO), Italy
Phone: [phone]
Fax: [phone]
e-mail: [e-mail]

DEUBLIN Austria

Lainzer Straße 35
1130 Wien, Austria
Phone: [phone]
Fax: [phone]
e-mail: [e-mail]

DEUBLIN France

61 Bis, Avenue de l‘Europe
Z.A.C de la Malnoue, Emerainville
77436 Marne-la-Vallée Cedex 2, France
Phone: [phone]
Fax: [phone]
e-mail: [e-mail]

DEUBLIN Poland

ul. Bierutowska 57-59
51-317 Wrocław, Poland
Phone: [phone]
Fax: [phone]
e-mail: [e-mail]

DEUBLIN Russia

ul. Kosygina, 13, 5th entrance, 1st floor
Moscow, 119334, Russia
Phone: [phone]
Fax: [phone]
e-mail: [e-mail]

DEUBLIN Spain

C/ Lola Anglada, 20 local 1
08228 Terrassa, Spain
Phone: [phone]
Fax: [phone]
e-mail: [e-mail]

DEUBLIN United Kingdom

6 Sopwith Park, Royce Close, West Por tway
Andover SP10 3TS, UK
Phone: [phone]
Fax: [phone]
e-mail: [e-mail]

DEUBLIN USA

2050 Norman Drive
Waukegan, IL 60085-6747 U.S.A
Phone: [phone]
Fax: [phone]
e-mail: [e-mail]

DEUBLIN Brazil

Rua Fagundes de Oliveira, 538 - Galpão A11
Piraporinha
09950-300 – Diadema - SP - Brasil
Phone: [phone]
Fax: [phone]
e-mail: [e-mail]

DEUBLIN Mexico

Norte 79-A No. 77, Col. Claveria
02080 Mexico, D.F.
Phone: [phone]
Fax: [phone]
e-mail: [e-mail]

ASIA

DEUBLIN China

No. 2, 6th DD Street,
DD Port Dalian, 116620, China
Phone: [phone]
Fax: [phone]
e-mail: [e-mail]

Shanghai Branch Office

Room 15A07, Wangjiao Plaza
No. 175 East Yan’an Road, Huangpu District
Shanghai 200002
Phone: [phone]
Fax: [phone]
e-mail: [e-mail]

DEUBLIN Asia Pacific

51 Goldhill Plaza
#17-02 Singapore 308900
Phone: [phone]
Fax: [phone]
email: [e-mail]

DEUBLIN Japan

2-13-1, Minamihanayashiki, Kawanishi City
Hyogo 666 -0026, Japan
Phone: [phone]
Fax: [phone]
e-mail: [e-mail]

2-4-10-3F, Ryogoku, Sumida-ku
Tokyo 130-0026, Japan
Phone: [phone]
Fax: [phone]
e-mail: [e-mail]

1-9-2-4F, Mikawaanjo-cho, Anjo City
Aichi 446-0056, Japan
Phone: [phone]
Fax: [phone]
e-mail: [e-mail]

DEUBLIN Korea

Star Tower #1003, Sangdaewon-dong 223-25,
Jungwon-gu, Seongnam-si, Gyeonggi-do,
South Korea
Phone: [phone]
Fax: [phone]
e-mail: [e-mail]