Deteknix Wire-Free W3, Wire-Free WA, Wire-Free WR, Wire-Free W6 User Manual

Wire-Free

W3 W6 WA WR

Wireless Headphone Kit

Deteknix Inc | 1211 Center Court Dr. Suite 103 Covina, CA U.S.A. 91724

Tel: [phone] [e-mail] | www.deteknix.com

TECHNICIAN SPECIFICATION

Headphone

Transducer type............................Dynamic

Operating principle .....................Closed

Frequency response.....................20–20,000Hz

Nominal impedance....................32Ω

Sound pressure level ..................111dB

Power handling capacity .............100 mW

Max. sound pressure level .......... 131 dB

Sound coupling to the ear ..........Supra-aural

Headband pressure ....................2.5N

Wireless technology....................Digital 2.4GHz

Paring type..................................Manually digital

Weight.........................................115g

Charging.....................................USB 2.0

Power..........................................3.7VDC

Current........................................40mA

Battery ........................................300mAh Li-Poly

Transmitting power......................5dbm

Transmitter / Receiver

Transmitter Cable......................... 25cm straight+5cm coil; 5cm straight(WR)

Connector......................................W3(3.5mm) W6(6.35mm) WA(AT pro)

Attaching.......................................Clip on rod or hang on.

Protection level..............................Indoor or outdoor using splash-proof

Control...........................................One touch button; three buttons (WR )

Weight ..........................................33g

premium

metal detector
accessories

d.

*W3 Wireless Headphone Kit as demonstrated

Congratulations on your purchase of this Wire-Free headphone
kit. Before using your headphones for the first time, please take
a moment to carefully read the following information.

SAFETY INSTRUCTIONS

•

When wearing the headphones, make sure the volume is turned to
minimum. Only adjust the volume after putting the headphones on.
Do not turn the volume up too loud. You could cause permanent
damage to your hearing.

•

Danger to life! Headphones dramatically reduce your ability to hear
ambient noise. Using headphones while in road traffic is potentially
very dangerous and is therefore prohibited by law. Also, please make
sure that you do not use your headphones when in the vicinity of
possibly dangerous machines and tools.

•

This product’s wireless 2.4G technology has a transmission range of
approx. 10 meters, but interfering obstacles (people, metal objects,
walls, etc.), other radio signals, and other factors may affect the
transmission range or even loss connection.

IN THE BOX

One lite headphone
One transmitter unit
One USB 2.0 charger cable
Two elastic bands, one adapter , one soft carry case .

IMPORTANT-PLEASE READ

Please read this operation manual thoroughly before using.

Fully recharge the batteries before using.

Do not expose the devices under direct sunshine.

Do not immerse the devices in any liquid.

Do not pull on cables to unplug transmitter.

1.1 HEADPHONE ADJUSTMENT

Before wearing the Wire-Free lite headphone for the first time
you should adjust it properly to achieve the best sound and
ambient noise attenuation.

Unfold the headphone pad as the figure 1. and 2. Select the
appropriate lock-in position on both sides of the headband as
figure 3. The pads will adjust the angle automatically according to
your head size.

1

2 3

1.2 POWER ON TRANSMITTER

Make sure the transmitter is fully charged and press the power
button for 1 second. The LED indicator will start to flash.

1.4 PARING

Each set of Wire-Free have been pre-paired before packing. If you
need pair them again please place the headphone to within 10cm
of the transmitter, press and release the power button of the
headphone quickly. The LED indicator of the transmitter will
change to steady condition.

1.3 POWER ON HEADPHONE

Make sure the headphones are fully charged and press the power
button(between two volume buttons) for 1 second. The LED
indicator will start to flash.

deteknix

!

1.5 TRANSMITTER ATTCHMENT

We provide two methods to attach the transmitter to your detector.
For headphone jack on control box, you can clip it on the rod by elastic
band. For headphone jack under the arm-rest, you can paste the iron
piece on flat place and attach the transmitter on it.

Now you have turned your detector into wireless!

2.1 TRANSMITTER RECHARGING

You can recharge it thru smartphone charger(recommend)
laptop computer USB port, or power bank for emergency.
Plug the USB side into the port and insert the microUSB head
on the transmitter’s charging port.
The LED indicator will start to flash. It will turn off when fully
charged.

2.2 HEADPHONE RECHARGING

You can also charge the headphone through the USB 2.0 cable
by computer, smartphone wall charger(recommend) or
portable power bank. The green light will turns off when fully
charged. It will takes about 2 to 3 hours .

1.6 VOLUME CONTROL

If the detector’s audio is too laud or low, you can also adjust the
headphone volume by press the volume buttons.
You can also adjust the receiver(WA) volume by the buttons on the
touch pad.