Detection Systems DS7080iP-32, DS7443S, DS7445, DS7447 User Manual

Download

DS7080iP-32 Security

System User’s Guide

An instruction guide for your alarm system

when used with a

DS7443S, DS7445 or DS7447 keypad

Armed

Status

Power

Fire

456

789

Entry

System

Reset

Bypass

Perimeter

Only

Off

Ready to Arm

- Page 2 -

System Overview

Congratulations on the installation of your new security system. No other investment can provide such peace of

mind. Welcome to the DS7080iP-32 intr usion/fire control system. Since each installation is unique, yours will contain

some, but not necessarily all of the features mentioned in this guide.

A security system usually consists of:

• A Control Panel: The control panel is the center of your intrusion/fire alarm system. It supports such vital functions as receiving trouble and alarm signals from detectors, the sounding of bells and/or sirens, and communicating with your alarm monitoring company.

• Command Control Stations (Keypads): The keypad is where y ou interact with the system. The k eypad displays critical information concerning the operation of your alarm system, plus it allows you to initiate commands such as arming and disarming.

• Protected Zones: Your security system may contain protected windows and doors (perimeter zones), plus various internal sensors. Your control panel separates perimeter zones from interior protection zones. Specific protection devices may include:

• Glass breakage sensors: Devices that detect the sound of breaking glass.

• Interior motion sensors: Electronic sensors (e.g. passive infrared) that detect movement within an interior zone.

• Magnetic contacts: Switches used to detect the opening of doors or windows.

• Smoke detectors: Devices that detect products of combustion.

This system includes a telephone line seizure feature. The system may be programmed to communicate with a central monitoring station to report system events. You will not be able to use your phone while the system is communicating with the central monitoring station. In the unlikely e v ent that the central station is not able to receiv e the report, your phone may be una vailab le for up to 20 min utes while the panel makes additional communication attempts.

- Page 3 -

Table of Contents

Your system may or may not be monitored by an alarm monitoring service. If it is not monitored, it is vital to understand the following:

• Alarms sound only at your location.

• When an alarm is sounded, no signals are sent out.

• Duress and other silent alarms are disabled.

• Emergency alarms sound only at your location.

System Overview .................................................................. 2

Understanding the DS7443S, DS7445 and DS7447 Keypads 4

Understanding Partitioning .................................................... 6

Turning ON (Arming) your System......................................... 7

Quick Arming Your System .................................................... 9

Turning OFF (Disarming) your System / Silencing Alarms ... 10

Force Arming your System .................................................. 11

Zone Bypassing................................................................... 12

Chime Mode ........................................................................ 13

Access Control .................................................................... 14

Setting the Date................................................................... 15

Setting the Time................................................................... 16

Automatic Arming ................................................................ 17

Delaying Automatic Arming.................................................. 18

Setting Delayed Arming ....................................................... 19

Emergency Procedures ....................................................... 20

Turning OFF (Disarming) your System under Duress.......... 21

Fire Reset / Fire Trouble ...................................................... 23

Fire Safety ........................................................................... 24

Personal Identification Numbers .......................................... 26

Removing a PIN ................................................................. 26

Error Displays...................................................................... 29

T esting Y our System ............................................................ 31

Event History Readback ...................................................... 34

Glossary .............................................................................. 35

Quick Reference Guide ....................................................... 36

System Features Reference Guide...................................... 37

Index.................................................................................... 39

- Page 4 -

Understanding the DS7443S, DS7445 and DS7447 Keypads

continued on next page

This chart will help you understand what each Light/LED represents.

The DS7443S is an LED keypad; its LEDs 1-6 represent the first 6 z ones of the system (zones 7-32 are not displayed). The DS7445 is an LED keypad; its LEDs 1-8 represent the first 8 zones of the system (zones 9-32 are not displayed). The DS7447 is an alphanumeric LCD keypad. All three keypads display info rmation on various control panel functions as indicated in the following charts. A built-in sounder is used to annunciate keystroke entries and as an interior warning device.

DS7447

Armed

Status

Power

Fire

123

456

789

Entry

System Reset

Bypass

Only

Perimeter

Off

DS7445

Armed

Status

Power

Fire

Perimete r

Supervisory

Bell Silenced

Trouble

12345678

123

456

789

Entry

System Reset

Bypass

Only

Perimete r

Off

DS7443S

No Entry

System

Reset

Bypass

Perimeter

Only

Off

654

987

321

Fire

Armed

Status

Power

TEST WEEKLY

- Page 5 -

Understanding the DS7447, DS7443S and DS7445 Keypads (continued)

Lights Present only on the DS7443S Keypad

Light Off Flashing On

LEDs 1-6

(red)

There are no zone

alarms.

A zone (1-6) has been alarmed. (Zones 7-32 are not displayed.)

A zone (1-6) is Not Ready to Arm or if a fire

zone, a trouble condition exists. (Zones 7-32

are not displayed.)

Lights Present only on the DS7445 Keypad

Light Off Flashing On

Perimeter

(yellow)

The perimeter is not

armed.

This Light will not flash. The perimeter is armed.

Supervisory

(yellow)

This Light is not used

by the DS7080iP-32.

Not used. Not used.

Bell

Silenced

(yellow)

The bells do not need

to be or have been

silenced.

This Light will not flash. There has been a Fire alarm and the bells

have been silenced. To clear, enter the Fire

Rest command.

Trouble

(yellow)

There are no trouble

conditions.

This Light will not flash. A trouble condition exists.

LEDs 1-8

(red)

There are no zone

alarms.

A zone (1-8) has been alarmed. (Zones 9-32 are not displayed.)

A zone (1-8) is Not Ready to Arm or if a fire

zone, a trouble condition exists. (Zones 9-32

are not displayed.)

- Page 6 -

Understanding Partitioning

Your alarm system may be Partitioned.

A Partitioned system is a system that is divided into two areas which may be armed and disarmed independently. The following applies in a Partitioned system:

• User PIN numbers are always required to perform operations in a Partitioned system.

• DS7447 LCD keypads will alternately display (about every 2 seconds) the current status of each partition.

• DS7443S and DS7445 LED keypads will alternately display (about every 2 seconds) the current status of each partition by wa y of the LED’s. See “Understanding the DS7447, DS7443S and DS7445 Keypads” on pages 4 and 5 for details.

• If the User PIN has authority in only one Partition, using that PIN on any keypad will perform Arming and Disarming commands only for the Partition in which the User has authority.

• If the User PIN has authority in both Partitions, the User may arm or disarm both Partitions by entering the commands from any keypad.

• Only Users with access to both partitions can arm common zones.

• If the User PIN has authority in both Partitions, the User may arm or disarm the first Partition only by entering the [PIN] + [#] [#] + [Arming/ Disarming command]. To perform arming or disarming commands in the second Partition only, enter the [PIN] + [#] [#] [#] [#] + [Arming/ Disarming command].

• If Custom Arming ([PIN] + [#] [4]) is used in a Partitioned system, the following will apply:

- Users with access to both partitions can Custom Arm all zones.

- Users with access to both partitions cannot custom ar m a single partition.

- Users with access to Partition 1 can Custom Arm any zones in Partition 1 but cannot arm common zones or zones in Partition 2.

- Users with access to Partition 2 can Custom Arm any zones in Partition 2 but cannot arm common zones or zones in Partition 1.

- Page 7 -

Turning ON (Arming) your System

This chart explains the five normal ways to arm the system.

The green Status Light must be on steady and the display (if using the DS7447 ke ypad) m ust read “Read y to Arm” in order to arm the system with one of these commands. If the green Status Light is not on, or if the displa y (if using the DS7447 k e ypad) is reading “Not Ready, ”then see

Force Arming

Zone Bypass

for other ways to arm the system.

If this is a Partitioned system, please read “Understanding Partitioning” before using this chart.

Note: In commercial burglar alarm applications for UL Listed Requirement systems, a ring-back indication and bell test should be heard after

arming (closing). If not heard, call for service.

- Page 8 -

Note: In commercial burglar alarm applications for UL Listed Requirement systems, a ring-back indication and bell test should be heard after

arming (closing). If not heard, call for service.

If this is a Partitioned system, please read “Understanding Partitioning” before using this chart.

Turning ON (Arming) your System (continued)

- Page 9 -

This chart explains four ways to quick arm the system from the keypads.

If Quick Arming is not used, a PIN must be entered at the beginning of all arming command sequences. Quick Arming is not available in a partitioned system. When Quick Arming is used, the following shortcuts are available:

Quick Arming Command Sequence Type of Arming

[#] + [On] Normal Arming

[#] + [No Entry] + [Perimeter Only] Perimeter Arming – No Entry Delay

[#] + [Perimeter Only] Perimeter Arming – Entry/Exit Delay

[#] + [No Entry] + [On] Maximum Security Arming

Quick Arming Your System

- Page 10 -

This chart explains proper procedures for disarming and/or silencing alarms.

Please read the section about Emergency Procedures prior to being confronted with an emergency event. If you have entered the building through a perimeter door , y ou ma y hear a steady pre-alert tone from the keypads. If so, disarm according to the chart below.

If the bells and sirens are on and/or the red Armed Light is flashing, then the keypad is signaling that an alarm has occurred sometime before your arrival. The DS7447 will display “Zone Alarm”. The DS7443S zone LEDs (1-6) (Zones 7 - 32 will not be displayed) or the DS7445 zone LEDs (1-8) (zones 9 - 32 will not be displayed) will be flashing for the corresponding zone that is in alar m.

• The keypad will also issue a pulsed tone during the entry delay instead of the usual steady tone.

• If the alarm has not been previously investigated, do not enter the building unless accompanied by the appropriate Emergency Services’ personnel.

* In non-partitioned systems. For systems with partitioning, review the sections on “Understanding the Keypads” and “Understanding

Partitioning”.

Turning OFF (Disarming) your System / Silencing Alarms

- Page 11 -

Force Arming your System

This chart explains the procedure for Force Arming your system if one or more zones are faulted.

When one or more zones are faulted, the system may be F orce Armed (if programmed) by b ypassing the f aulted z ones. The green Status Light will be off on all keypads when Force Arming is required to arm the system. The DS7447 display will read “Not Ready” and the DS7443S and DS7445 zone LEDs will be on (the DS7443S cannot display zones 7 - 32 and the DS7445 cannot display z ones 9 - 32) if one of thos e z ones is faulted. In a partitioned system, only users with authority to the faulted zone may perform the Force Arming of that Par tition.

Force Arming during an AC power failure: Regular arming of the control panel is not permitted during an AC power failure. Having to Force Arm serves as a warning that the control panel is operating under backup battery.

Bypassing or Force Arming removes some of your b uilding’ s protection because it e xcludes the f aulted z ones from arming. Therefore, an intrusion may not be detected or the detection may be delayed. Always attempt to correct any zone problems (close doors and windows etc.) before using these features. If the problem can not be corrected, contact your installing company.

Note: See the section on Zone Bypassing for an alternate method of arming the system when faults exist. Force arming is not available in

UL Listed systems.

- Page 12 -

Zone Bypassing

This chart explains the procedure for bypassing a faulted zone prior to arming the system.

There may be occasions when it is desirable or necessary to temporarily bypass one or more zones prior to arming the system. Bypass commands only work when the control panel is disarmed. For instance, an open window may cause the DS7447 display to read “Not Ready” followed by the z one n umber. The DS7443S and DS7445 may ha v e one of its zone LEDs on steady (the DS7443S cannot display zones 7 - 32 and the DS7445 cannot display zones 9 - 32). Only one zone may be bypassed each time the command is used. If more than one zone requires bypassing, repeat the command for each zone to be bypassed.

Note: See Force Arming for another method of zone bypassing.

- Page 13 -

Chime Mode

This chart explains the procedure for turning ON and turning OFF Chime Mode.

Chime Mode causes all the keypad sounders to beep each time a Perimeter or Entry/Exit zone is violated while the control panel is off (disarmed). The [#] [7] command is used to both turn Chime Mode off and on.

You cannot set the Chime mode by partition.

- Page 14 -

This chart explains the procedure for activating devices that require an Access Control PIN.

Your system may or may not use a keypad key sequence to activate other electrical devices. The special PIN required to perform this function is known as an Access Control PIN. This feature can be used in armed or disarmed modes. The PIN may control devices that activate for a short period of time (e.g. electric locking mechanisms on a door).

Access Control

- Page 15 -

This chart will guide you through the steps necessary to change the date displayed at the keypads.

You should write down your entries before you enter the Master Code Programming Mode and have them with you as y ou begin progr amming. Make your entries promptly. If a long delay occurs in your entries, the 3-beep error tone sounds and exits you from the programming mode.

Setting the Date

Note: If the control panel loses power, the date will need to be set again.

- Page 16 -

Setting the Time

This chart will guide you through the steps necessary to change the Time displayed at the keypads.

Note: If the control panel loses power, the time will need to be set again.

- Page 17 -

Automatic Arming

Note: The panel time and date must be set in order for this feature to work properly.

To inform occupants that the system is about to ar m, a pre-arming period will begin 15 minutes before the system arms automatically. If programmed by the installing company, the keypad sounders, and any outputs programmed to f ollow the k e ypad sounders , will pulse fiv e times every minute. During the last fiv e minutes bef ore arming, these sounders will be on steady. Once per minute the DS7447 keypad will read, “Arm in nn min./PIN + OFF - extend.”

Automatic Arming will affect only the partitions you have access to. Each partition can be programmed to automatically arm once per day. To program the Automatic Arming Time, perform the following:

- Page 18 -

Delaying Automatic Arming

This section explains how to delay the Automatic Arming Time.

To inform occupants that the system is about to ar m, a pre-ar ming per iod will begin 15 minutes before the system arms automatically. If programmed by the installing company, the keypad sounders, and any outputs programmed to follow the keypad sounders, will pulse five times every minute. During the last five minutes before arming, these sounders will be on steady.

Once per minute the DS7447 keypad will read, “Arm in nn min./PIN + OFF - extend.” Delayed Automatic Arming will affect only the partitions you have access to. To extend the Automatic Arming of the system during the automatic ar ming pre-ar ming per iod, perform the following steps:

* = To extend the Automatic Arming at any time, use the Delayed Arming feature in the “Setting Dealyed Arming” seciton.

Note: The keypad volume setting also applies to the Auto Arm tone. Note: The panel time and date must be set in order for this feature to work.

- Page 19 -

Setting Delayed Arming

This section explains how to cause the system to arm after a specified number of hours.

Delayed arming is simply causing the system to arm after a specified number of hours. To program the system for delayed arming, perform the following steps:

Additional Notes: Delayed arming can be used even if there are no automatic arming times programmed. Setting Delayed Arming will affect only the partitions you have access to. Users with PIN levels of 0-2 will be able to set Delayed arming.

Delayed arming will override automatic arming. Dela yed arming will also provide a 15 minute pre-arm period like the one provided with automatic arming.

Y ou ma y view the time left (rounded to the nearest hour) to the arming time by entering [PIN] + [#] [9] [9]. The display will show “Arm In __ Hours”. Pressing the [*] key will exit the display without changing the arming time.

Note: The panel time and date must be set in order for this feature to work.

- Page 20 -

Identifying Alarm Sounds

Your alarm system may be programmed for a steady alarm sound or a pulsed alarm sound. It is important to learn the difference between a fire alarm sound and an intrusion alarm sound before you are confronted with an actual emergency.

Silencing Alarms

All alarms can be silenced with any PIN that has disarm privileges. Entering your [PIN] + [Off] will silence the alarm and turn off (disarm) the control.

A Cautionary Note

How you respond to an alarm will depend, mostly , on the type and time of the alarm. You should seek the advice of your installing company as they install your system, not later (e.g. after an alar m) to develop a response plan.

Above all else, common sense should prevail.

If there is any threat or hint of danger to yourself or others on the premises, such as in the event of a fire alarm, everyone should be instructed to leave the premises immediately . Do not enter the premises unless accompanied by the appropriate Emergency Services’ personnel, or after they have given the OK to enter.

Emergency Procedures

Caution When Entering A Building

If the bells and sirens are on and/or the red Armed Light is flashing with the DS7447 display reading “Zone Alarm”, or the DS7445 zone LEDs 1-8 are flashing, or the DS7443 zone LEDs 1-6 are flashing, then the keypad is signaling that an alarm has occurred. The keypad will also issue a pulsed tone during the entry delay instead of the usual steady tone.

If the alarm has not been previously investigated, do not enter the

building unless accompanied by the appropriate Emergency Services’ personnel.

Fire Alarms

Fire Alarms are silenced using the same procedure as intrusion alarms: a [PIN] (with disarm privileges) + [Off].

The Fire Alarm system is not reset until alarms at smoke detectors are cleared by using the [System Reset] command. The Fire Alarm system will not be functional until this procedure has been followed. See the “Fire Reset / Fire Trouble” section for more infor mation.

- Page 21 -

Turning OFF (Disarming) your System under Duress

This chart explains the proper procedure for disarming under duress.

Ask your installer if the Duress feature has been activated. A Duress code is used when someone demands, by threatening your life or well-being, that the system be turned off. When used, the code will

both turn off the system and report a silent Duress alarm if connected to a monitoring service. Extreme care should be used when entering your PIN to turn off the system, so a Duress code is not inadvertently entered. The Duress code will only disarm partitions that it has been assigned to.

- Page 22 -

Emergency Keypad Alarms / Silencing Alarms

The Emergency Alarm Keys A, B and C may generate Fire, Special Emergency, and Panic Alarms if programmed by the installer. Ask your installing company to explain the function of these keys.

When using the Emergency Alarm Keys, they must be pressed for two seconds to generate an alarm.

Note: If the Emergency Alarm Keys are to be used, they should be labeled to signify their functions.

The A key should be labeled as the Fire key. This is the only key that may be designated as the Fire key. The B key should be labeled as the Special Emergency key. The C key should be labeled as the Panic key.

Use the Disarming Command Sequence to cancel or silence these alarms.

Entry

System

Reset

Bypass

Perimeter

Only

Off

321

654

987

Fire

Armed

Status

Power

TEST WEEK LY

ABC

Armed

Status

Power

Fire

Perimeter

Supervisory

Bell Silenced

Trouble

12345678

123

456

789

Entry

System

Reset

Bypass

Only

Perimeter

Off

ABC

Armed

Status

Power

Fire

123

456

789

Entry

System Reset

Bypass

Only

Perimeter

Off

ABC

- Page 23 -

Fire Reset / Fire Trouble

Fire Reset

During a fire alarm, exit the premises immediately. When you have determined there is no fire, it is recommended that you silence the bells/sirens before you initiate the [System Reset] command.

Before the [System Reset] command is used, determine which smoke detector has alarmed so the installing company may verify its operation.

A PIN followed by the [System Reset] key will reset any smoke detectors after a fire alarm has occurred.

[PIN] + [System Reset]

Note: To use the System Reset command sequence, your

PIN must have disarm privileges. The System Reset command will perform a fire reset, will

perform a battery test, and will clear all system troubles.

Fire Tr ouble

A Fire Trouble display signifies a problem with the fire system, such as a break in the wiring that monitors smoke detectors.

A Fire Trouble will be indicated by a short beep from the keypad sounders every 10 seconds. The DS7447 keypad will display “Fire Tr ouble” followed by the zones in a trouble condition.

The DS7443S and DS7445 keypads will turn the Fire and Trouble Lights on steady and will light the corresponding zone LEDs (the DS7443S will not display zones 7 - 32 and the DS7445 will not display z ones 9 -

32). Notify your installing company immediately if the Fire Trouble message

is displayed. The Fire Trouble beep can be silenced with any [PIN] followed by [Off].

After problems have been remedied, a [PIN] + [System Reset] should be entered to clear the “Sounder Silenced” display.

- Page 24 -

Fire Safety

This fire alarm system can provide early warning of a developing fire. Such a system, however, does not ensure protection against property damage or loss of life resulting from a fire. Any fire alarm system may fail to warn for any number of reasons (e.g. smoke not reaching a detector that is behind a closed door).

When considering detectors for residential applications, refer to NFPA Standard 72, “The National Fire Alarm Code. ” This standard is availab le at a nominal cost from: The National Fire Protection Association, Batterymarch Park, Quincy, MA 02269.

If Installed in Family Residences

Adherence to the NFP A Standard 72 can lead to reasonable fire saf ety when the following items are practiced:

• Minimize hazards: Avoid the three traditional fire killers: smoking in bed, leaving children home alone, and cleaning with flammable liquids.

• Providing a fire warning system: Most fire deaths occur in the home, the majority, during sleeping hours. The minimum level of protection requires smoke detectors to be installed outside of each separate sleeping area and on each additional story of the dwelling.

For added early warning protection, it is recommended that detectors be installed in all separated areas including the basement, bedrooms, dining room, utility room, furnace room, and hallways.

Having and Practicing an Escape Plan

A fire warning may be wasted unless the family has planned in advance for a rapid and safe exit from the building.

• Draw a floor plan of the entire house showing two exits from each bedroom and two from the house. Since stairwells and hallways may be bloc ked during a fire, the plan should provide exits from bedroom windows.

Make copies of the plan and practice it with all family members.

• Prearrange a meeting place outside and away from the residence. Once out of the building, all occupants should immediately go to the pre-selected location to be accounted for.

No fire detection system should be considered 100 percent foolproof

continued on next page

- Page 25 -

Fire Safety (continued)

• Provide a barricade between family members and fire, smoke, and toxic gases (e.g. close all bedroom doors before retiring).

• Children should be instructed on opening their bedroom windows and exiting safely from the building. If exiting is not possible, they should be taught to stay at the open window and shout for help until it arrives.

• In the event of a fire alarm after retiring, wake the children b y shouting to them from behind your closed door. T ell them to keep their bedroom doors closed.

• If the top of your bedroom door is uncomfortably hot, do not open it. There is most likely fire, intolerable heat, or smoke on the other side. Shout to all f amily members to k eep their bedroom doors closed and to exit the building via alternate routes.

• If the top of the door is not uncomfortably hot, brace the bottom of the door with your foot, and the top with one hand, then open the door about one inch. Be prepared to slam the door shut if there is any pressure against the door or if any hot air rushes in.

• If there is no evidence of excessive heat or pressure, leave the room and close the door behind you. Shout appropr iate instructions to all family members and immediately leave the building via the pre-planned routes. If heavy smoke is present, drop to your hands and knees and crawl to remain below the smoke level.

Installation Considerations

Proper location of detection devices is one of the most critical factors in a fire alarm system. The following are some general considerations:

• Smoke detectors should not be installed in “dead air” spaces or close to ventilating or air conditioning outlets because smoke may be circulated away from the detector. Locations near air inlets should be favored.

• Avoid areas subject to nor mal smoke concentrations such as kitchens, garages, or near fireplaces.

• Do not install smoke detectors where normal area temperatures are above 100 degrees F (38 degrees C) or below 32 degrees F (0 degrees C).

• Areas of high humidity and dust concentrations should be avoided.

• The edge of ceiling mounted detectors should be no closer than 4 inches (10 cm) from any wall.

• Place the top edge of wall mounted detectors between 4 and 12 inches (10 to 30 cm) from the ceiling.

- Page 26 -

Personal Identification Numbers

General Information

When programing Personal Identification Numbers, it is helpful to kno w the following terms:

• PIN: Personal Identification Number. This is the 4- or 6-digit code users enter at the keypad to gain access to the system. A PIN may be assigned to each User Number 001 - 024.

• Partition (Area): This is the area the User has authority in. You may select Partition (Area) 1, 2 or both.

• User Number: This is the number that identifies each person using the system. There are 24 possible User Numbers (001 - 024).

• Authority Level: This number determines which functions each user will be able to perform (see “Pin Authority Levels”).

Your system has the capacity to assign up to 24 PINs. The length of the PINs will be fixed at 4 or 6 digits. You cannot have both 4- and 6digit PINs in the same system. If you wish to change the PIN length, it will be necessary to have your installing company make the change . If changed, all new PINs will need to be assigned. Each User number may have only one PIN assigned to it. Attempting to assign the same PIN to multiple User Numbers will result in a 3 beep entry error tone, and the entry will not be made.

User Number 001 is designated as a Master Code. It can be used to add, delete or change other PINs and will always hav e access to both partitions regardless of how it is programmed.

User Number 001 is shipped from the factory with the sequence of

123456. If four-digit PINs are used on your system then the default master code will be 1234. This code should be changed to one of y our personal preference, and must be programmed as a Master Code. PINs should never be programmed with common sequences such as 1111 or 2468 because they are easily violated.

Removing a PIN

To remove a PIN: enter a [Master Code] [#] [0] [0], the [User Number] of the PIN to be canceled, and then [#] again.

User Number 001 can not be canceled in this manner.

continued on next page

- Page 27 -

Personal Identification Numbers (continued)

PIN Authority Levels

0 = Master: Can enter all commands, add or change PINs, change

time and date, bypass, arm, set autoarm, disarm, perform system tests, system reset, and view history . User number 001 must be a master code and must have authority 0. Any or all user PINs may be master codes.

1 = Unlimited: Can enter all commands, bypass , arm, disarm, system

reset, and perform system tests. Can not change PINs.

2 = General: Can bypass, ar m and disarm. Can not change PINs,

perform system reset, or enter the [#] [7] or [#] [8] functions.

3 = Arm Only: Can arm the system with [#] + [On] arming only. Can

not perform any other functions including disarming.

4 = Temporary: Valid only for a limited time. Can arm and disarm the

system, but can not perform any other functions. This code will automatically be deleted after 15 days if you have not already done so.

The 15 day clock is reset to 15 days each time a Temporary

PIN is assigned. All Temporary PINs expire at the same time.

5 = Duress: When the system is armed and you disarm it using a

duress code, a silent report is sent to the central station. Duress codes are intended to be used when the user is forced to disarm the system.

6 = Access: When a PIN with Access Code authority is entered, any

output programmed for Access Output (e.g. door strikes) will pulse on for 10 seconds (works when the system is armed or disarmed).

continued on next page

- Page 28 -

Personal Identification Numbers (continued)

This chart will guide you through the steps necessary to change a PIN.

- Page 29 -

Error Displays

This chart explains the procedure for reading Error messages when the green Power Light is flashing.

Control panel problems are indicated by a flashing green Power Light and the DS7447 display reading “Control Tr ouble, Enter #87.” Error messages may only be read when the control is disarmed. Contact your installing company if the problems persist.

1. “AC Power Failure”* or LED #1 on steady**: There is a power

failure and the control panel is running on backup battery.

2. “Battery T rouble”* or LED #2 on steady**: If the system has just

been through a power failure, wait at least tw o hours for the battery to recharge, then enter [PIN] + [System Reset] to perform a battery test.

3. “Communicator Err”* or LED #3 on steady**: The communicator

failed to communicate with the central station.

4. “System Fault”* or LED #4 on steady**: Internal error in the control

panel’s circuitry or optional circuitry. These faults are designated as follows:

5. “Ke ypad Fault”* or LED #5 on steady**: One of the keypads is not

responding to the control panel.

6. “Aux Power Fault”* or LED #7 on steady**: The Auxiliar y power has been shorted.

7. “Zone T rouble”*: One or more of the zones is not responding to the control panel. This may also display during pow er-up (if so, ignore).

* = the DS7447 display ** = the DS7443S and DS7445 displays *** = If in “Residential Mode”, a PIN is not required for these commands. **** = Battery Trouble and Communicator Err displays must be cleared by the [System Reset] command sequence even after the problem has been remedied. These displays will not self clear. All the other error displays will self clear from the keypads once the problem has been remedied.

continued on next page

- Page 30 -

Error Displays (continued)

8. “Pt Exp Mssng”* or LED #8 on steady**: The EX8 Zone Expansion Module is missing, defective or not communicating with the Options bus.

9. “Pt Exp Tamper”* or LED #8 on steady**: The EX8 Zone Expansion Module has a tamper condition.

10.“Pt Exp Fault”* or LED #8 on steady**: The EX8 Zone Expansion Module has had a DC overcurrent fault.

11.“Keypad Tamper”* or LED #6 on steady**: One of the keypad housings has been opened.

- Page 31 -

Testing Your System

This chart explains the procedure for performing a Zone Test.

It is recommended that the system be tested weekly. The Zone Test is used to confirm that detectors will report alarms to the keypad. A Zone Test works on all zones, except 24-hour zones and fire zones. While the keypad is in a Zone Test, no control panel alarms will activate an alarm, except 24-hour zone alarms and fire alarms; these will

override the Zone Test function.

Type of

Test

Command Sequence*

What Will Happen What To Do

Zone Test [PIN] + [#] [8] [1]

“

Test Zone

” will display on the DS7447 followed by the zone number of any zones that have not been tested.

The DS7443S and DS7445 keypads will flash the zone LEDs of any untested zones. The DS7443S cannot display zones 7-32.

“

Now Testing

” will display on the DS7447 followed by the zone number of the zone that is currently being violated (tested). It returns to “

Test Zone

” after the violation.

The DS7443S and DS7445 will turn the zone LED on steady for the zone that is currently being violated (tested).

The DS7443S cannot display zones 7-32.

The DS7445 cannot display zones 9-32.

Test each detector one at a time as instructed by the installing company.

To exit the Zone Test mode, enter your [PIN] followed by the [#] key.

- Page 32 -

Testing Your System (continued)

This chart explains the procedure for performing a Battery Test.

If a power failure occurs, your control panel has a b uilt-in battery that will continue to power the control panel for many hours. The control panel automatically recharges the battery when power is restored.

In addition to an automatic battery test performed every 2 minutes, the battery may also be tested manually. This test also uses the battery to manually activate all the system sounders for 2 seconds ([#] [8] [5] only). If the battery voltage is lo w, a battery

fault will occur (see

Error Displays

- Page 33 -

Testing Your System (continued)

This chart explains the procedure for performing a Communicator Test.

This test is available only if your system transmits alarms and system information to a monitoring service, and has been programmed by the security installing company to permit communicator tests.

A long beep will initially sound to acknowledge the start of the test. If the test is successful, the sounder will again issue one long beep. If the test fails, the keypad sounder will turn ON continuously. To silence the sounder, enter [PIN] + [#] or press the [*] key.

- Page 34 -

Event History Readback

This chart explains the procedure for performing an Event History Readback.

The History Buffer stores the last 100 events in memory. All events are stored in non-volatile memory and will be retained even in the event of a power loss. The DS7447 can display all of these events.

The DS7443S and DS7445 keypads will only display those zones that have alarmed. The DS7443S cannot display zones 7 - 32; the DS7445 cannot display zones 9 - 32.

DS7447 Only: Scrolling through the History Events. Event History Readback operation: To begin scrolling back through the events, press the [#] key. The [#] key will scroll you back through the

history line by line. The [9] k ey will scroll you bac k in rev erse chronological order by e v ent. A [6] will scroll you bac k up through the ev ents (toward the most recent) by event.

Each event consists of two lines or display screens . The first line/screen will be the event title and user. The second line/screen will be the date of the event or the change being made.

To exit the Event History Mode, press the [*] key or wait 20 seconds and the keypad will exit automatically.

- Page 35 -

Glossary

Access Control PIN

A special code used to activate electric door locks or other mechanisms connected to the control panel that require this code to turn them on or off.

Armed/Disarmed

Arming the system (burglar zones) means to turn it on. Disarming the system means to turn it off. Remember , fire protection (if installed) is always Armed/on.

Central Station/Monitoring Service

A facility used to continuously monitor phone signals from your system. Trained personnel there dispatch proper authorities as necessary.

Custom Arming

A type of arming that uses the [#] [4] sequence. It is only a valid sequence if programmed by the installing company. It is a specific type of arming designed for your individual installation needs. Ask your installing compan y to e xplain Custom Arming further.

Disarming Command Sequence

The sequence of keys you press at the k eypad to disarm the system and/or silence alarms. It consists of your PIN followed by the [Off] button.

Entry Delay

A predetermined amount of time that allows entry into an armed area.

Exit Delay

A predetermined amount of time that allows you to exit an area just after you have ar med it.

Faulted Zone

A zone that is not ready to arm (e.g. an open door or window). It may also be descr ibed as being violated.

Force Arming

Force Arming is a way of arming the system by bypassing zones that are not ready to arm. This reduces the level of security and should be avoided.

Installing Company

The company that physically installed the system. It may or may not be the same company who monitors the system.

Local System

A system that has a control panel that is not programmed to call a monitoring service. It will sound only local (on sight) bells or sirens when an intrusion or fire alarm is detected.

Monitored System

A system that uses phone lines to notify a monitoring service of select abnormal events such as burglar or fire alarms.

Zone

A Zone is an input to the control panel. There are eight hard-wired zones on the control panel. A zone is usually some type of detection device whether it be designed for burglar or fire.

Zone Bypassing

Zone Bypassing is a way of arming the system by deliberately eliminating zones to be armed.

Zone Function

A Zone Function is the description of how a zone behaves in the system. Zone Functions usually define how a zone will respond when armed or when it detects an alarm.

- Page 36 -

Quick Reference Guide

This system should be tested weekly to ensure it is functioning properly. If problems are detected in testing or changes are noticed in normal operation, call your installing company for service. The manufacturer recommends replacing the system battery every 3 to 5 years.

Monitoring Service Phone Number: ______________________________ Monitoring Service System Number: _____________________________ Installing Company Phone Number: _____________________________

- Page 37 -

System Features Reference Guide

Audible Alarm Signaling Device Sounds

Intrusion ( ) Pulse ( ) Continuous Fire ( ) Pulse ( ) Continuous

Keypad Supplemental Alarm [B] Key

( ) Continuous ( ) Silent This system has the Duress Alarm feature. ( ) Yes ( ) No This system has the communicator test feature. ( ) Yes ( ) No This system is partitioned. ( ) Yes ( ) No

Partition 1 Zones Partition 2 Zones Common Zones 1- _____________ ______________ _____________ 2- _____________ ______________ _____________ 3- _____________ ______________ _____________ 4- _____________ ______________ _____________ 5- _____________ ______________ _____________ 6- _____________ ______________ _____________ 7- _____________ ______________ _____________ 8- _____________ ______________ _____________ 9- _____________ ______________ _____________ 10- _____________ ______________ _____________ 11- _____________ ______________ _____________ 12- _____________ ______________ _____________ 13- _____________ ______________ _____________ 14- _____________ ______________ _____________ 15- _____________ ______________ _____________ 16- _____________ ______________ _____________

Partition 1 Zones Partition 2 Zones Common Zones 17- _____________ ______________ _____________ 18- _____________ ______________ _____________ 19- _____________ ______________ _____________ 20- _____________ ______________ _____________ 21- _____________ ______________ _____________ 22- _____________ ______________ _____________ 23- _____________ ______________ _____________ 24- _____________ ______________ _____________ 25- _____________ ______________ _____________ 26- _____________ ______________ _____________ 27- _____________ ______________ _____________ 28- _____________ ______________ _____________ 29- _____________ ______________ _____________ 30- _____________ ______________ _____________ 31- _____________ ______________ _____________ 32- _____________ ______________ _____________

Turning On (Arming) Your System

Normal Arming: [PIN] + [On]

Perimeter Arming, no entry delay: [PIN] + [No Entry] + [Perimeter Only]

Perimeter Arming, with entry delay: [PIN] + [Perimeter Only]

Maximum Security Arming: [PIN] + [No Entry] + [On]

- Page 38 -

System Features Reference Guide (continued)

Custom Arming

[PIN] + [#] [4] Arms _____________________

Force Arming

Enter an arming command sequence followed by the [Bypass] key. The maxim um number of zones that can be forced armed is __________

Zone Bypass

[PIN] + [Bypass] followed by the 2-digit Zone number.

Quick Arming Your System

Normal Arming: [#] + [On] Perimeter Arming, no entry delay:

[#] + [No Entry] + [Perimeter Only] Perimeter Arming, with entry delay:

[#] + [Perimeter Only] Maximum Security Arming:

[#] + [No Entry] + [On]

Turning Off (Disarming) Your System

Enter your [PIN] followed by [Off]

Chime Mode [PIN] + [#] [7]

Zone T est [PIN] + [#] [8] [1]

Read Event History [PIN] + [#] [8] [9]

Battery T est [PIN] + [System Reset]

Communicator Test [PIN] + [#] [8] [2]

Fire Reset [PIN] + [System Reset]

Fire Trouble [PIN] + [Off] to silence, [PIN] + [System Reset] to clear

Remote Program Dial-out [PIN] + [#] [8] [3]

Remote Program Answer [PIN] + [#] [8] [6]

Local Battery/Sounder Test [PIN] + [#] [8] [5]

Error Display [PIN] + [#] [8] [7]

Error Display Reset [PIN] + [System Reset]

Clear Zone Bypass [PIN] + [Bypass] [*] to clear

Access Control [PIN] + [Off]

Set Delayed Arming [PIN] + [#] [9] [9]

Delay Auto Arm by 30 Minutes [PIN] + [OFF]

Select Partition 1 only Arming/Disarming [PIN] + [#] [#] + [Arm Sequence]

Select Partition 2 only Arming/Disarming [PIN] + [#] [#] [#] [#] + [Arm Sequence]

- Page 39 -

Index

AC Power Failure 11, 29, 30 Access Control 14 Access Control PIN 35 Armed 35 Arming

Force 11

Quick 9 Arming (Turning ON) System 7 Authority Level 26 Automatic Arming 17 Aux Power Fault 29

Battery Test 32 Battery Trouble 29, 30 Bypass 12

Central Station 35 Change a PIN 28 Chime Mode 13 Communicator Err 29, 30 Communicator Test 33 Control Panel 2 Control Station 2 Control Trouble 29 Custom Arming 6, 35

Delayed Arming 19 Delayed Automatic Arming 18 Disarmed 35 Disarming Command Sequence 35 Disarming Under Duress 21 DS7445 4 DS7447 4

Emergency Procedures 20 Entry Delay 35 Event History Readback 34 Exit Delay 35

Faulted Zone 35 Fire Alarms 20 Fire Key 22 Fire Reset 23 Fire Safety 24 Fire Trouble 23 Force Arming 11, 35

History Buffer 34

Installing Company 35

Keypad Fault 29

Line Seizure 2 Local System 35

Monitored System 35 Monitoring Service 35

Not Ready 7

Panic Key 22 Partition 26 Partitioned 6 Partitioning 6 Personal Identification Numbers 26 PIN 26 PIN Authority Levels 27 Protected Zones 2

Quick Arming 9

Ready to Arm 7 Removing a PIN 26

Setting Delayed Arming 19 Setting the Date 15 Setting the Time 16 Silencing Alarms 20 Special Emergency Key 22 System Fault 29, 30

Turning ON (Arming) System 7

User Number 26

Zone 35 Zone Bypassing 12, 35 Zone Function 35 Zone Test 31 Zone Trouble 29

Detection Systems, Inc., 130 Perinton Parkway, Fairport, New York, USA 14450-9199

For Service

Please contact your Installing

Company at the above number

Detection Systems DS7080iP-32, DS7443S, DS7445, DS7447 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual