Desa CGD3924NRA User Manual

PREMIUM AGED SPLIT OAK AND

YELLOW FLAME UNVENTED (VENT-FREE)

NATURAL GAS LOG HEATERS

Also Design-Certified As Vented Decorative Appliances When

Not Used With Hand-Held Thermostat Remote

OWNER’S OPERATION AND INSTALLATION MANUAL
CGD3924NRA

CCL3018NR
CCL3924NR
CCL3930NR

18", 24" and 30" Remote Ready

(Yellow Flame Model Shown)

H

O

I

F

F

N

E

T

O

M

E

R

O

P

I

T

L

O

L
O

F

F

O

WARNING: If the information in this
manual is not followed exactly, a fire or
explosion may result causing property
damage, personal injury, or loss of life.

— Do not store or use gasoline or other

flammable vapors and liquids in the
vicinity of this or any other appliance.

WARNING: Improper installation, ad­justment, alteration, service, or mainte­nance can cause injury or property dam­age. Refer to this manual for correct
installation and operational procedures.
For assistance or additional informa­tion consult a qualified installer, ser­vice agency, or the gas supplier.

— WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do
not use any phone in your building.

• Immediately call your gas supplier
from a neighbor’s phone. Follow the
gas supplier’s instructions.

• If you cannot reach your gas sup­plier, call the fire department.

— Installation and service must be per-

formed by a qualified installer, service
agency, or the gas supplier.

WARNING: This appliance is for instal­lation only in a solid-fuel burning ma­sonry or UL127 factory-built fireplace,
or in an approved ventless firebox. It is
design-certified for these installations
in accordance with ANSI Z21.11.2.
Exception: Do not install this appli­ance in a factory-built fireplace that
includes instructions stating it has not
been tested or should not be used with
unvented gas logs.

WARNING: This is an unvented gas-fired heater. It uses air (oxygen) from the room in
which it is installed. Provisions for adequate combustion and ventilation air must be
provided. Refer to

Air for Combustion and Ventilation

section on page 4 of this manual.

This appliance may be installed in an aftermarket,* manufactured (mobile) home,
where not prohibited by local codes.

This appliance is only for use with the type of gas indicated on the rating plate. This
appliance is not convertible for use with other gases.

* Aftermarket: Completion of sale, not for purpose of resale, from the manufacturer

Save this manual for future reference.

UNVENTED NATURAL GAS LOG HEATER
SAFETY

INFORMATION

WARNINGS

IMPORTANT: Read this owner’s
manual carefully and completely
before trying to assemble, oper­ate, or service this heater. Im­proper use of this heater can cause
serious injury or death from burns,
fire, explosion, electrical shock,
and carbon monoxide poisoning.

DANGER: Carbon monoxide

poisoning may lead to death!

Carbon Monoxide Poisoning: Early signs of

carbon monoxide poisoning resemble the flu,
with headaches, dizziness, or nausea. If you
have these signs, the heater may not be work­ing properly. Get fresh air at once! Have
heater serviced. Some people are more af­fected by carbon monoxide than others. These
include pregnant women, people with heart or
lung disease or anemia, those under the influ­ence of alcohol, and those at high altitudes.

Natural Gas: Natural gas is odorless. An

odor-making agent is added to the gas. The
odor helps you detect a gas leak. However,
the odor added to the gas can fade. Gas may
be present even though no odor exists.

Make certain you read and understand all warn­ings. Keep this manual for reference. It is your
guide to safe and proper operation of this heater.

WARNING: Any change to this
heater or its controls can be
dangerous.

WARNING: Do not allow fans
to blow directly into the fireplace.
Avoid any drafts that alter burner
flame patterns. Ceiling fans can
create drafts that alter burner
flame patterns. Altered burner
patterns can cause sooting.

WARNING: Do not use a
blower insert, heat exchanger
insert, or other accessory not ap­proved for use with this heater.

Due to high temperatures, the
appliance should be located out
of traffic and away from furniture
and draperies.

Do not place clothing or other
flammable material on or near
the appliance. Never place any
objects on the heater.

Heater base assembly becomes
very hot when running heater. Keep
children and adults away from hot
surface to avoid burns or clothing
ignition. Heater will remain hot for
a time after shutdown. Allow sur­face to cool before touching.

Carefully supervise young chil­dren when they are in the room
with heater. When using the hand­held remote accessory, keep se­lector switch in the OFF position
to prevent children from turning
on burners with remote.

You must operate this heater with
a fireplace screen in place. Make
sure fireplace screen is closed
before running heater.

Keep the appliance area clear and
free from combustible materials,
gasoline, and other flammable
vapors and liquids.

1. This appliance is only for use with the
type of gas indicated on the rating plate.
This appliance is not convertible for use
with other gases.

2. If you smell gas

• shut off gas supply

• do not try to light any appliance

• do not touch any electrical switch; do

not use any phone in your building

• immediately call your gas supplier

from a neighbor’s phone. Follow the
gas supplier’s instructions

• if you cannot reach your gas supplier,

call the fire department

3. This heater shall not be installed in a
bedroom or bathroom unless installed
as a vented appliance (see Installing

Damper Clamp Accessory for Vented
Operation, page 10).

4. Before installing in a solid fuel burn­ing fireplace, the chimney flue and fire­box must be cleaned of soot, creosote,
ashes, and loose paint by a qualified
chimney cleaner. Creosote will ignite
if highly heated. Inspect chimney flue
for damage. If damaged, operate heater
with flue damper closed.

5. If fireplace has glass doors, never op­erate this heater with glass doors closed.
If you operate heater with doors closed,
heat buildup inside fireplace will cause
glass to burst. Also if fireplace open­ing has vents at the bottom, you must
open the vents before operating heater.

6. This log heater is designed to be smoke­less. If logs ever appear to smoke, turn
off heater and call a qualified service per­son.

Note:

During initial operation, slight
smoking may occur due to log curing and
heater burning manufacturing residues.

7. T o prevent the creation of soot, follow
the instructions in Cleaning and Main-
tenance, page 18.

8. Before using furniture polish, wax, car­pet cleaner, or similar products, turn
heater off. If heated, the vapors from
these products may create a white resi­due within burner box or on adjacent
walls or furniture.

9. This heater needs fresh, outside air ven­tilation to run properly . This heater has
an Oxygen Depletion Sensing (ODS)
safety shutoff system. The ODS shuts
down the heater if not enough fresh air
is available. See Air for Combustion
and Ventilation, pages 4 through 6. If
heater keeps shutting off, see Trouble-
shooting, pages 19 through 21.

10. Do not run heater

• where flammable liquids or vapors

are used or stored

• under dusty conditions

11. Do not use this heater to cook food or
burn paper or other objects.

12. Do not use heater if any part has been
exposed to or under water. Immediately
call a qualified service technician to in­spect the room heater and to replace any
part of the control system and any gas
control which has been under water.

13. Do not operate heater if any log is bro­ken. Do not operate heater if a log is
chipped (dime-sized or larger).

For more information, visit www.desatech.com

2

107553

OWNER’S MANUAL

SAFETY
INFORMATION

Continued

LOCAL CODES

Install and use heater with care. Follow all
local codes. In the absence of local codes, use
the latest edition of The National Fuel Gas

14. Turn heater off and let cool before ser­vicing, installing, or repairing. Make sure

Code, ANSI Z223/NFPA 54*.
*Available from:

the remote selector switch is in the OFF
position. Only a qualified service person
should install, service, or repair heater.

15. Make sure the remote selector switch is
in the OFF position when you are away
from home for long periods of time.

16. This heater must not be connected to
any external electrical source.

17. Operating heater above elevations of
4,500 feet may cause pilot outage.

American National Standards Institute, Inc.

1430 Broadway

New York, NY 10018

National Fire Protection Association, Inc.

Batterymarch Park

Quincy, MA 02269

Note:

Where listed vented decorative logs
are required, thermostat operation is not
permitted.

18. Provide adequate clearances around air
openings.

PRODUCT IDENTIFICATION

Back Log

Crossover Log

Front Log

Optional
Remote
Control

W
A

R
M

E
R

C
O

T

O

E

L

M

E

P

R
A
U
T

O
O
N

O
F
F

Piezo Ignitor

Optional Selector Switch

Base Grate

Flame Adjustment Knob

Control Knob

Figure 1 - Yellow Flame Vent-Free Gas Log Heater Shown (Logs May Vary by Model)

Burner

Middle Log

UNPACKING

CAUTION: Do not remove
the data plates attached to the
heater base assembly. The data
plates contain important war­ranty and safety information.

1. Remove logs and heater base assem­bly from carton.

Note:

Do not pick up
heater base assembly by burners. This
could damage heater. Always handle
base assembly by grate.

2. Remove all protective packaging ap­plied to logs and heater for shipment.

3. Check all items for any shipping dam­age. If damaged, promptly inform
dealer where you bought heater.

PRODUCT
FEATURES

OPERATION

This heater is clean burning. It requires no
outside venting. There is no heat loss out a
vent or up a chimney. Heat is generated by
realistic dancing, yellow flames. This heater
is designed for vent-free operation with flue
damper closed. It has been tested and ap­proved to ANSI Z21.11.2 standard for
unvented heaters. State and local codes in
some areas prohibit the use of vent-free
heaters. This heater may also be operated as
a vented decorative (ANSI Z21.60) product
by opening flue damper (non-thermostat
models only).

SAFETY PILOT

This heater has a pilot with an Oxygen
Depletion Sensing (ODS) safety shutoff
system. The ODS/pilot is a required feature
for vent-free room heaters. The ODS/pilot
shuts off the heater if there is not enough
fresh air.

PIEZO IGNITION SYSTEM

This heater has a piezo ignitor. This system
requires no matches, batteries, or other
sources to light heater.

107553

3

For more information, visit www.desatech.com

UNVENTED NATURAL GAS LOG HEATER
REMOTE CONTROL

ACCESSORIES

There are two optional remote controls that
can be purchased separately for this log
heater:

• hand-held ON/OFF remote

• hand-held thermostat remote
See Accessories, page 27.
The hand-held thermostat may not be used

where vented decorative listing is required.

AIR FOR
COMBUSTION AND
VENTILATION

WARNING: This heater shall
not be installed in a confined space
or unusually tight construction
unless provisions are provided
for adequate combustion and ven­tilation air. Read the following in­structions to insure proper fresh
air for this and other fuel-burning
appliances in your home.

Today’s homes are built more energy effi­cient than ever. New materials, increased
insulation, and new construction methods
help reduce heat loss in homes. Home owners
weather strip and caulk around windows and
doors to keep the cold air out and the warm air
in. During heating months, home owners
want their homes as airtight as possible.

While it is good to make your home energy
efficient, your home needs to breathe. Fresh
air must enter your home. All fuel-burning
appliances need fresh air for proper com­bustion and ventilation.

Exhaust fans, fireplaces, clothes dryers, and
fuel burning appliances draw air from the
house to operate. You must provide ad­equate fresh air for these appliances. This
will insure proper venting of vented fuel­burning appliances.

PROVIDING ADEQUATE
VENTILATION

The following are excerpts from National
Fuel Gas Code, ANSI Z223.1/NFPA 54, Sec­tion 5.3, Air for Combustion and Ventilation.

All spaces in homes fall into one of the three
following ventilation classifications:

1. Unusually Tight Construction

2. Unconfined Space

3. Confined Space
The information on pages 4 through 6 will

help you classify your space and provide
adequate ventilation.

Unusually Tight Construction

The air that leaks around doors and win­dows may provide enough fresh air for
combustion and ventilation. However, in
buildings of unusually tight construction,
you must provide additional fresh air.

Unusually tight construction is de­fined as construction where:

a. walls and ceilings exposed to the

outside atmosphere have a con­tinuous water vapor retarder with
a rating of one perm (6 x 10
per pa-sec-m2) or less with open­ings gasketed or sealed

b. weather stripping has been

added on openable windows and
doors

c. caulking or sealants are applied

to areas such as joints around
window and door frames, be­tween sole plates and floors, be­tween wall-ceiling joints, be­tween wall panels, at penetra­tions for plumbing, electrical, and
gas lines, and at other openings.

If your home meets all of the three
criteria above, you must provide ad­ditional fresh air. See

From Outdoors

If your home does not meet all of the
three criteria above, proceed to

and

Ventilation Air

, page 6.

termining Fresh-Air Flow For Heater
Location

, page 5.

and

-11

kg

De-

Confined Space and Unconfined
Space

The National Fuel Gas Code, ANSI Z2123.1/
NFPA 54 defines a confined space as a space

whose volume is less than 50 cubic feet per
1,000 Btu per hour (4.8 m
aggregate input rating of all appliances in­stalled in that space and an unconfined space
as a space whose volume is not less than 50
cubic feet per 1,000 Btu per hour (4.8 m
kw) of the aggregate input rating of all
appliances installed in that space. Rooms
communicating directly with the space in
which the appliances are installed*, through
openings not furnished with doors, are con­sidered a part of the unconfined space.

* Adjoining rooms are communicating only
if there are doorless passageways or ventila­tion grills between them.

3

per kw) of the

3

per

For more information, visit www.desatech.com

4

107553

OWNER’S MANUAL

AIR FOR COMBUSTION
AND VENTILATION

Continued

DETERMINING FRESH-AIR FLOW FOR HEATER LOCATION

Determining if You Have a Confined or Unconfined Space

Use this work sheet to determine if you have a confined or unconfined space.
Space: Includes the room in which you will install heater plus any adjoining rooms with doorless passageways or ventilation grills between

the rooms.

1. Determine the volume of the space (length x width x height).
Length x Width x Height = _________________cu. ft. (volume of space)

Example:

If additional ventilation to adjoining room is supplied with grills or openings, add the volume of these rooms to the total volume of
the space.

2. Multiply the space volume by 20 to determine the maximum Btu/Hr the space can support.

_________________ (volume of space) x 20 = (Maximum Btu/Hr the space can support)

Example:

3. Add the Btu/Hr of all fuel burning appliances in the space.
Vent-free heater ____________________Btu/Hr
Gas water heater* ____________________Btu/Hr
Gas furnace ____________________Btu/Hr
Vented gas heater ____________________Btu/Hr
Gas fireplace logs ____________________Btu/Hr
Other gas appliances*+____________________Btu/Hr
Total =____________________Btu/Hr
* Do not include direct-vent gas appliances. Direct-vent draws combustion air from the outdoors and vents to the outdoors.

4. Compare the maximum Btu/Hr the space can support with the actual amount of Btu/Hr used.

_________________ Btu/Hr (maximum the space can support)
_________________ Btu/Hr (actual amount of Btu/Hr used)

Example:

The space in the above example is a confined space because the actual Btu/Hr used is more than the maximum Btu/Hr the space can support.
You must provide additional fresh air. Your options are as follows:

A. Rework worksheet, adding the space of an adjoining room. If the extra space provides an unconfined space, remove door to adjoin-

ing room or add ventilation grills between rooms. See Ventilation Air From Inside Building, page 6.

B. Vent room directly to the outdoors. See Ventilation Air From Outdoors, page 6.
C. Install a lower Btu/Hr heater, if lower Btu/Hr size makes room unconfined.

If the actual Btu/Hr used is less than the maximum Btu/Hr the space can support, the space is an unconfined space. You will need no
additional fresh air ventilation.

Space size 20 ft. (length) x 16 ft. (width) x 8 ft. (ceiling height) = 2560 cu. ft. (volume of space)

2560 cu. ft. (volume of space) x 20 = 51,200 (maximum Btu/Hr the space can support)

Example:

Gas water heater
Vent-free heater +
Total =

51,200 Btu/Hr (maximum the space can support)
79,000 Btu/Hr (actual amount of Btu/Hr used)

40,000
39,000
79,000

Btu/Hr
Btu/Hr
Btu/Hr

WARNING: If the area in which the heater may be operated is smaller than that defined as an unconfined space
or if the building is of unusually tight construction, provide adequate combustion and ventilation air by one of
the methods described in the

107553

National Fuel Gas Code, ANSI Z223.1/NFPA 54, Section 5.3

5

For more information, visit www.desatech.com

or applicable local codes.

Continued

UNVENTED NATURAL GAS LOG HEATER
AIR FOR

COMBUSTION AND
VENTILATION

Continued

VENTILATION AIR

Ventilation Air From Inside
Building

This fresh air would come from an adjoining
unconfined space. When ventilating to an
adjoining unconfined space, you must pro­vide two permanent openings: one within
12" of the ceiling and one within 12" of the
floor on the wall connecting the two spaces
(see options 1 and 2, Figure 2). You can also
remove door into adjoining room (see op­tion 3, Figure 2). Follow the National Fuel

Gas Code, ANSI Z223.1/NFPA 54, Section

5.3, Air for Combustion and Ventilation for

required size of ventilation grills or ducts.

Ventilation Air From Outdoors

Provide extra fresh air by using ventilation
grills or ducts. You must provide two per­manent openings: one within 12" of the
ceiling and one within 12" of the floor.
Connect these items directly to the outdoors
or spaces open to the outdoors. These spaces
include attics and crawl spaces. Follow the

National Fuel Gas Code, ANSI Z223.1/
NFPA 54, Section 5.3, Air for Combustion
and Ventilation for required size of ventila-

tion grills or ducts.

IMPORTANT:

inlet or outlet air into attic if attic has a
thermostat-controlled power vent. Heated air
entering the attic will activate the power vent.

Do not provide openings for

Ventilation

Grills

Into Adjoining

Room,

Option 1

Figure 2 - Ventilation Air from Inside Building

Outlet
Air

Inlet
Air

Figure 3 - Ventilation Air from Outdoors

Or

Remove

Door into

Adjoining

Room,
Option

3

12"

Outlet
Air

Inlet Air

Ventilation Grills

Into Adjoining Room,

Option 2

Ventilated
Attic

Ventilated

Crawl Space

12"

To Attic

To

Crawl

Space

For more information, visit www.desatech.com

6

107553

OWNER’S MANUAL

INSTALLATION

NOTICE: This heater is intended
for use as supplemental heat. Use
this heater along with your pri­mary heating system. Do not in­stall this heater as your primary
heat source. If you have a central
heating system, you may run
system’s circulating blower while
using heater. This will help circu­late the heat throughout the
house. In the event of a power
outage, you can use this heater
as your primary heat source.

NOTICE: State or local codes may
only allow operation of this appli­ance in a vented configuration.
Check your state or local codes.

WARNING: A qualified ser­vice person must install heater.
Follow all local codes.

WARNING: Make sure the se­lector switch is in the OFF posi­tion before installing heater.

WARNING: Before installing
in a solid fuel burning fireplace,
the chimney flue and firebox must
be cleaned of soot, creosote,
ashes, and loose paint by a quali­fied chimney cleaner. Creosote
will ignite if highly heated. A dirty
chimney flue may create and dis­tribute soot within the house. In­spect chimney flue for damage. If
damaged, operate heater with flue
damper closed.

WARNING: Never install the

heater

• in a bedroom or bathroom un­less installed as a vented ap­pliance, see page 10.

• in a recreational vehicle

• where curtains, furniture,
clothing, or other flammable
objects are less than 42 inches
from the front, top, or sides of
the heater

• in high traffic areas

• in windy or drafty areas

CAUTION: This heater creates
warm air currents. These currents
move heat to wall surfaces next to
heater. Installing heater next to
vinyl or cloth wall coverings or
operating heater where impurities
(such as, but not limited to, to­bacco smoke, aromatic candles,
cleaning fluids, oil or kerosene
lamps, etc.) in the air exist, may
discolor walls or cause odors.

IMPORTANT:

ture to the air. Although this is beneficial,
installing heater in rooms without enough
ventilation air may cause mildew to form
from too much moisture. See Air for Com-
bustion and Ventilation, pages 4 through 6.

Vent-free heaters add mois-

CHECK GAS TYPE

Use only natural gas. If your gas supply is not
natural gas, do not install heater. Call dealer
where you bought heater for proper type heater.

INSTALLATION AND
CLEARANCES
(Vent-Free Operation Only)

MINIMUM FIREPLACE

CLEARANCE TO

COMBUSTIBLE MATERIALS

Log Size Side Wall Ceiling

ALL 16" 42"

LOG SIZING REQUIREMENTS

Minimum Firebox Size

Log Front Rear
Size Height Depth Width Width*

18" 17" 13" 28" 20"
24" 17" 13" 28" 21"
30" 17" 13" 34" 24"

*Measured at 13" depth
Carefully follow the instructions below. This

will ensure safe installation into a masonry,
UL127-listed manufactured fireplace, or
listed vent-free firebox.

Minimum Clearances for Side
Combustible Material, Side Wall,
and Ceiling

A. Clearances from the side of the fireplace

cabinet to any combustible material and
wall should follow diagram in Figure 4.

Example:

etc. is made of combustible material and
protrudes 3 1/2" from the wall. This com­bustible material must be 4" from the side
of the fireplace opening (see Figure 4).

Note:

a manufactured firebox, follow firebox
manufacturer’s instructions for minimum
clearances to combustible materials.

B. Clearances from the top of the fireplace

opening to the ceiling should not be less
than 42 inches.

The face of a mantel, bookshelf,

When installing your gas logs into

WARNING: Seal any fresh air
vents or ash clean-out doors lo­cated on floor or wall of fireplace.
If not, drafting may cause pilot
outage or sooting. Use a heat­resistant sealant. Do not seal
chimney flue damper.

107553

WARNING: Maintain the mini­mum clearances. If you can, pro­vide greater clearances from
floor, ceiling, and adjoining wall.

7

Example

*

*Minimum 16 inches from Side Wall

Figure 4 - Minimum Clearance for Side Com­bustible Material, Side Wall, and Ceiling

Continued

For more information, visit www.desatech.com

UNVENTED NATURAL GAS LOG HEATER
INSTALLATION

Continued

NOTICE: Manual control heaters
may be used as a vented product.
If so, you must always run heater
with chimney flue damper open.
If running heater with damper
open, noncombustible material
above fireplace opening is not
needed. Go to

Clamp Accessory for Vented
Operation

Minimum Noncombustible
Material Clearances

If Not Using Mantel

Note:

If using a mantel, go to If Using

Mantel. If not using a mantel, follow the

information below.
You must have noncombustible material(s)

above the fireplace opening. Noncombus­tible materials (such as slate, marble, tile,
etc.) must be at least 1/2 inch thick. With
sheet metal, you must have noncombustible
material behind it. Noncombustible mate­rial must extend at least 8" up (for all mod­els). If noncombustible material is less than
12", you must install the fireplace hood
accessory (24" and 30" models only). See
Figure 5 for minimum clearances.

IMPORTANT:

minimum clearances, you must operate
heater with chimney flue damper open. Go
to Installing Damper Clamp Accessory for
Vented Operation, page 10.

Installing Damper

, page 10.

If you cannot meet these

If Using Mantel

You must have noncombustible material(s)
above the fireplace opening. Noncombus­tible materials (such as slate, marble, tile,
etc.) must be at least 1/2 inch thick. With
sheet metal, you must have noncombustible
material behind it. Noncombustible mate­rial must extend at least 8 inches up (for all
models). If noncombustible material is less
than 12", you must install the fireplace hood
accessory (24" and 30" models only). Even

Noncombustible Requirements for
Material Distance (A) Safe Installation

12" or more Noncombustible material okay.
Between 8" and 12" Install fireplace hood accessory (GA6050, GA6052,

or GA6053, see

Less than 8" Noncombustible material must be extended to at

least 8". See
cannot extend material, you must operate heater
with flue damper open.

Heat Resistant
Material

if noncombustible material is more than
12", you may need the hood accessory to
deflect heat away from your mantel shelf.
See Figure 5 and Figures 6 and 7 on page 9
for minimum clearances.

IMPORTANT:

minimum clearances, you must operate
heater with chimney flue damper open. Go
to Installing Damper Clamp Accessory for
Vented Operation, page 10.

Accessories

Between 8" and 12"

(A)

If you cannot meet these

, page 27).

, above. If you

Figure 5 - Heat Resistant Material (Slate, Marble, Tile, etc.) Above Fireplace

For more information, visit www.desatech.com

8

107553

OWNER’S MANUAL

INSTALLATION

Continued

MANTEL CLEARANCES

In addition to meeting noncombustible mate­rial clearances, you must also meet required
clearances between fireplace opening and
mantel shelf. If you do not meet the clear­ances listed below, you will need a hood.

Determining Minimum Mantel
Clearances

If you meet minimum clearance between
mantel shelf and top of fireplace opening, a
hood is not required (see Figure 6).

Determining Minimum Mantel
Clearances When Using a Hood

If minimum clearances in Figure 6 are not
met, you must have a hood. When using a
hood there are still certain minimum mantel
clearances required. Follow minimum clear­ances shown in Figure 7 when using hood.

NOTICE: Surface temperatures of
adjacent walls and mantels be­come hot during operation. Walls
and mantels above the firebox
may become hot to the touch. If
installed properly, these tempera­tures meet the requirements of
the national product standard.
Follow all minimum clearances
shown in this manual.

NOTICE: If your installation does
not meet the minimum clearances
shown, you must do one of the
following:

• operate the logs only with the
flue damper open

• raise the mantel to an accept­able height

• remove the mantel

Mantel Shelf

18"8"20"

14"

Distances to
Underside of
Mantel

22"
17"

Underside of
Mantel Shelf

24"
20"

Top of Fireplace
Opening

Minimum Non­Combustible
Material

10"
8"
6"

1

/2

"

2

(A)

12"
8"

Minimum Non­Combustible
Material Height

Figure 6 - Minimum Mantel Clearances Without Using Hood

8"
Min.

Mantel Shelf

12" 15" 18"

Distances to
Underside of
Mantel

Underside of
Mantel Shelf

All minimum
distances are
in inches

All Models

20"

Top of Fireplace
Opening

Minimum Non­Combustible
Material

12"
10"
8"
6"

1

2

/2

"

Hood
(GA6050, GA6052)

Figure 7 - Minimum Mantel Clearances When Using Hood

All minimum
distances are
in inches

Log Set

24"/30" Models
18" Model

FLOOR CLEARANCES

A. If installing appliance on the floor level,

you must maintain the minimum distance
of 14" to combustibles (see Figure 8).

B. If combustible materials are less than

14" to the fireplace, you must install
appliance at least 5" above the combus­tible flooring (see Figure 9).

107553

Combustible

14"
Min.

Noncombustible Material

Material

Figure 8 - Minimum Fireplace Clearances
If Installed at Floor Level

9

For more information, visit www.desatech.com

Hearth

5"
Min.

Combustible
Material

Figure 9 - Minimum Fireplace Clearances
Above Combustible Flooring

Continued