Desa CF26PTA User Manual

UNVENTED (VENT-FREE) BAY FRONT GAS LOG FIREPLACE

A U T O

O F F

O N

OWNER’S OPERATION AND INSTALLATION MANUAL

Patent Pending

Fireplace Shown With Optional Bay Front Mantel

MODELS CF26PTA AND CF26NTA

19,000 TO 26,000 BTU/HR REMOTE CONTROL READY

WARNING: If the information in this manual is not followed exactly, a ﬁre or explosion may result causing property damage, personal injury, or loss of life.

— Do not store or use gasoline or other ﬂammable

vapors and liquids in the vicinity of this or any other appliance.

— WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone in your building.

• Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the ﬁre department.

— Installation and service must be performed by a quali-

ﬁed installer, service agency, or the gas supplier.

Save this manual for future reference.

For more information, visit www.desatech.com

WARNING: Improper installation, adjustment, alteration, service, or maintenance can cause injury or property damage. Refer to this manual for correct installation and operational procedures. For assistance or additional information consult a qualiﬁed installer, service agency, or the gas supplier.

WARNING: This is an unvented gas-ﬁred heater. It uses air (oxygen) from the room in which it is installed. Provisions for adequate combustion and ventilation air must be provided. Refer to Air for Combustion and Ventilation section on page 5 of this manual.

This appliance may be installed in an aftermarket,* permanently located, manufactured (mobile) home, where not prohibited by local codes.

This appliance is only for use with the type of gas indicated on the rating plate. This appliance is not convertible for use with other gases.

* Aftermarket: Completion of sale, not for purpose of resale, from the manufacturer

TABLE OF CONTENTS

Safety Information ............................................... 3

Local Codes ........................................................ 4

Unpacking ........................................................... 4

Product Identiﬁcation ........................................... 5

Product Features ................................................. 5

Air For Combustion and Ventilation ..................... 5

Installation ........................................................... 8

Operating Fireplace ........................................... 19

Inspecting Burners ........................................... 20

Cleaning and Maintenance ................................ 21

www.desatech.com

Troubleshooting .................................................

Speciﬁcations .................................................... 27

Replacement Parts ............................................ 27

Service Hints ..................................................... 27

Technical Service ..............................................

Illustrated Parts Breakdown and Parts List ....... 28

Parts Central ..................................................... 32

Accessories ....................................................... 32

Warranty Information ...........................Back Cover

6-01A

11389

SAFETY INFORMATION

WARNING: This product contains and/or generates chemicals known to the state of California to cause cancer or birth defects, or other reproductive harm.

IMPORTANT: Read this owner’s manual carefully and completely before trying to assemble, operate, or service this ﬁreplace. Improper use of this ﬁreplace can cause serious injury or death from burns, fire, explosion, electrical shock, and carbon monoxide poisoning.

DANGER: Carbon monoxide poisoning may lead to death!

Carbon Monoxide Poisoning:

monoxide poisoning resemble the ﬂu, with head aches, dizziness, or nausea. If you have these signs, the heater may not be working properly. Get fresh air at once! Have heater serviced. Some people are more affected by carbon monoxide than others. These include pregnant women, people with heart or lung disease or anemia, those under the inﬂuence of alcohol, and those at high altitudes.

Natural and Propane/LP Gas: Natural and pro-

pane/LP gases are odorless. An odor-making agent is added to the gas. The odor helps you detect a gas leak. However, the odor added to the gas can fade. Gas may be present even though no odor exists.

Make certain you read and understand all warn ings. Keep this manual for reference. It is your guide to safe and proper operation of this heater.

Early signs of carbon

WARNING: Do not allow fans to blow directly into the ﬁreplace. Avoid any drafts that alter burner ﬂame patterns. Ceiling fans can create drafts that alter burner ﬂame patterns. Altered burner patterns can cause sooting.

Due to high temperatures, the appliance should be located out of trafﬁc and away from furniture and draperies.

Do not place clothing or other ﬂammable material on or near the appliance. Never place any objects in the ﬁreplace or on logs.

Fireplace front and screen become very hot when running ﬁre place. Keep children and adults

away from hot surfaces to avoid burns or clothing ignition. Fire place will remain hot for a time after shutdown. Allow surfaces to cool before touching.

Carefully supervise young children when they are in the room with ﬁreplace.

You must operate this ﬁreplace with a ﬁreplace screen in place.

Make sure ﬁreplace screen is closed before running heater.

WARNING: Any change to this heater or its controls can be dangerous.

Keep the appliance area clear and free from combustible materials, gasoline, and other ﬂam mable vapors and liquids.

WARNING: Do not use a blower insert, heat exchanger insert, or other accessory not approved for use with this heater.

6-01A 3

11389

www.desatech.com

SAFETY INFORMATION

Continued

1. This appliance is only for use with the type of gas indicated on the rating plate. This ap pliance is not convertible for use with other gases.

2. Do not place propane/LP supply tank(s) in side any structure. Locate propane/LP supply tank(s) outdoors (propane/LP units only).

3. If you smell gas

• shut off gas supply

• do not try to light any appliance

• do not touch any electrical switch; do not use

any phone in your building

• immediately call your gas supplier from a

neighborʼs phone. Follow the gas supplierʼs instructions

• if you cannot reach your gas supplier, call

the ﬁre department

4. This ﬁreplace shall not be installed in a bed room or bathroom.

5. Do not use this ﬁreplace as a wood-burning ﬁreplace. Use only the logs provided with the ﬁreplace.

6. Do not add extra logs or ornaments such as pine cones, vermiculite, or rock wool. Using these added items can cause sooting. Do not add lava rock around base. Rock and debris could fall into the control area of ﬁreplace.

7. This fireplace is designed to be smokeless. If logs ever appear to smoke, turn off fire place and call a qualified service person. Note: During initial operation, slight smoking could occur due to log curing and ﬁreplace burning manufacturing residues.

8. To prevent the creation of soot, follow the instructions in Cleaning and Maintenance page 21.

9. Before using furniture polish, wax, carpet cleaner, or similar products, turn heater off. If heated, the vapors from these products may create a white powder residue within burner box or on adjacent walls or furniture.

10. This ﬁreplace needs fresh air ventilation to run properly. This ﬁreplace has an Oxygen Deple tion Sensing (ODS) safety shutoff system. The ODS shuts down the ﬁreplace if not enough fresh air is available. See Air for Combustion and Ventilation, page 5. If ﬁreplace keeps shutting off, see Troubleshooting, page 23.

11. Do not run ﬁreplace

• where ﬂammable liquids or vapors are used or stored.

• under dusty conditions.

12. Do not use this ﬁreplace to cook food or to burn paper or other solid fuels.

13. Do not use ﬁreplace if any part has been under

water. Immediately call a qualiﬁed service

technician to inspect the room ﬁreplace and to replace any part of the control system and any gas control which has been under water.

14. Turn off and unplug ﬁreplace and let cool before servicing. Only a qualiﬁed service person should service and repair ﬁreplace.

15. Operating ﬁreplace above elevations of 4,500 feet could cause pilot outage.

16. Do not operate ﬁreplace if any log is broken. Do not operate ﬁreplace if a log is chipped (dime-sized or larger).

17. To prevent performance problems, do not use

propane/LP fuel tank of less than 100 lbs.

capacity (propane/LP units only).

18. Prov id e adequate clearances aro un d air openings.

LOCAL CODES

Install and use ﬁreplace with care. Follow all local codes. In the absence of local codes, use the lat est edition of The National Fuel Gas Code, ANSI

Z223.1/NFPA 54

*Available from:

American National Standards Institute, Inc.

National Fire Protection Association, Inc.

1430 Broadway

New York, NY 10018

Batterymarch Park

Quincy, MA 02269

UNPACKING

1. Remove and ﬁreplace from carton.

2. Remove all protective packaging applied to ﬁreplace for shipment.

3. Make sure your ﬁreplace includes one hard ware packet.

4. Check ﬁreplace for any shipping damage. If

ﬁreplace is damaged, promptly inform dealer

where you bought ﬁreplace.

www.desatech.com

11389

6-01A

PRODUCT

IDENTIFICATION

Fireplace Cabinet

Brick Liner

Logs

Heater Controls (Inside Door)

Figure 1 - Vent-Free Propane/LP Gas

Screen

Compact Fireplace

PRODUCT FEATURES

SAFETY PILOT

This ﬁreplace has a pilot with an Oxygen Depletion Sensing (ODS) safety shutoff system. The ODS/pilot is a required feature for vent-free room ﬁreplaces. The ODS/pilot shuts off the ﬁreplace if there is not enough fresh air.

PIEZO IGNITION SYSTEM

This ﬁreplace has a piezo ignitor. This system requires no matches, batteries, or other sources to light ﬁreplace.

AIR FOR COMBUSTION

AND VENTILATION

WARNING: This heater shall not be installed in a conﬁned space or unusually tight con struction unless provisions are provided for adequate combus tion and ventilation air. Read the following instructions to insure proper fresh air for this and other fuel-burning appliances in your home.

Todayʼs homes are built more energy efﬁcient than ever. New materials, increased insulation, and new construction methods help reduce heat loss in homes. Home owners weather strip and caulk around windows and doors to keep the cold air out and the warm air in. During heating months, home owners want their homes as airtight as possible.

While it is good to make your home energy efﬁ cient, your home needs to breathe. Fresh air must enter your home. All fuel-burning appliances need fresh air for proper combustion and ventilation.

Exhaust fans, ﬁreplaces, clothes dryers, and fuel burning appliances draw air from the house to operate. You must provide adequate fresh air for these appliances. This will insure proper venting of vented fuel-burning appliances.

PROVIDING ADEQUATE VENTILATION

The following are excerpts from National Fuel Gas Code, ANSI Z223.1/NFPA 54 Section 5.3, Air for Combustion and Ventilation.

All spaces in homes fall into one of the three fol lowing ventilation classiﬁcations:

1. Unusually Tight Construction

2. Unconﬁned Space

3. Conﬁned Space

The information on pages 5 through 7 will help you classify your space and provide adequate ventilation.

6-01A 5

11389

www.desatech.com

AIR FOR COMBUSTION

AND VENTILATION

Continued

Unusually Tight Construction

The air that leaks around doors and windows may provide enough fresh air for combustion and ventilation. However, in buildings of unusually tight construction, you must provide additional fresh air.

Unusually tight construction is deﬁned as construction where:

a. walls and ceilings exposed to the out

side atmosphere have a continuous water vapor retarder with a rating of one perm (6 x 10 less with openings gasketed or sealed and

b. weather stripping has been added on

openable windows and doors and

c. caulking or sealants are applied to

areas such as joints around window and door frames, between sole plates and ﬂoors, between wall-ceiling joints, between wall panels, at penetrations for plumbing, electrical, and gas lines, and at other openings.

If your home meets all of the three criteria above, you must provide additional fresh air. See Ventilation Air From Outdoors, page 7.

If your home does not meet all of the three criteria above, proceed to Determining

Fresh-Air Flow For Fireplace Location

below.

Conﬁned and Unconﬁned Space

The National Fuel Gas Code, ANSI Z223.1 deﬁnes a conﬁned space as a space whose volume is less than 50 cubic feet per 1,000 Btu per hour (4.8 m per kw) of the aggregate input rating of all appliances installed in that space and an unconﬁning space as a space whose volume is not less than 50 cubic feet per 1,000 Btu per hour (4.8 m3 per kw) of the aggregate input rating of all appliances installed in that space. Rooms communicating directly with the space in which the appliances are installed*, through openings not furnished with doors, are considered a part of the unconﬁned space.

* Adjoining rooms are communicating only if there are doorless

-11

kg per pa-sec-m2) or

DETERMINING FRESH-AIR FLOW FOR FIREPLACE LOCATION

Determining if You Have a Conﬁned or Unconﬁned Space

Use this work sheet to determine if you have a conﬁned or unconﬁned space.

Space: Includes the room in which you will install heater plus any adjoining rooms with door less passageways or ventilation grills between the rooms.

1. Determine the volume of the space (length x width x height).

Length x Width x Height =__________cu. ft.

(volume of space)

Example: Space size 20 ft. (length) x 16 ft.

(width) x 8 ft. (ceiling height) = 2560 cu. ft. (volume of space)

If additional ventilation to adjoining room is

supplied with grills or openings, add the volume of these rooms to the total volume of the space.

2. Multiply the space volume by 20 to determine the maximum Btu/Hr the space can support.

__________ (volume of space) x 20 = (Maxi-

mum Btu/Hr the space can support)

Example: 2560 cu. ft. (volume of space) x 20 =

51,200 (maximum Btu/Hr the space can support)

3. Add the Btu/Hr of all fuel burning appliances in the space.

Vent-free ﬁreplace ___________

Gas water heater* ___________

Gas furnace ___________

Vented gas heater ___________

Gas ﬁreplace logs ___________

Other gas appliances* + ___________

Total = ___________

* Do not include direct-vent gas appliances. Di

rect-vent draws combustion air from the outdoors and vents to the outdoors.

Example:

Gas water heater

Vent-free ﬁreplace + ________

Total = ________

4. Compare the maximum Btu/Hr the space can support with the actual amount of Btu/Hr used.

_________

_________ Example: 51,200 Btu/Hr (maximum the space

56,000 Btu/Hr (actual amount of

Btu/Hr (maximum the space can support)

Btu/Hr (actual amount of Btu/Hr used)

can support)

Btu/Hr used)

30,000

__________ Btu/Hr

26,000

56,000

Btu/Hr

www.desatech.com

11389

6-01A

AIR FOR COMBUSTION

Or Remove Door into

Adjoining

Room,

Option

Ventilation Grills

Into Adjoining Room,

Option 2

12"

Ventilation

Grills

into Adjoining

Room,

Option 1

Outlet Air

Ventilated Attic

Outlet

Inlet Air

Ventilated

Crawl Space

To Attic

To Crawl Space

AND VENTILATION

Continued

The space in the above example is a conﬁned space because the actual Btu/Hr used is more than the maximum Btu/Hr the space can support. You must provide additional fresh air. Your options are as follows:

A. Rework worksheet, adding the space of an adjoin-

ing room. If the extra space provides an unconﬁned space, remove door to adjoining room or add ventilation grills between rooms. See Ventilation

Air From Inside Building.

B. Vent room directly to the outdoors. See Ventila

tion Air From Outdoors.

C. Install a lower Btu/Hr ﬁreplace, if lower Btu/Hr

size makes room unconﬁned.

If the actual Btu/Hr used is less than the maximum Btu/Hr the space can support, conﬁned space. You will need no additional fresh air ventilation.

WARNING: If the area in which the heater may be operated is smaller than that deﬁned as an unconﬁned space or if the building is of unusually tight construction, provide adequate combustion and ventilation air by one of the methods described in the National Fuel Gas Code, ANSI Z223.1/NFPA 54 Section 5.3 or applicable local codes.

the space is an un-

Figure 2 - Ventilation Air from Inside

Building Shown with Optional Mantel

Ventilation Air From Outdoors

Provide extra fresh air by using ventilation grills or ducts. You must provide two permanent openings: one within 12” of the ceiling and one within 12” of the ﬂoor. Connect these items directly to the outdoors or spaces open to the outdoors. These spaces include attics and crawl spaces. Follow the

National Fuel Gas Code ANSI Z223.1/NFPA 54, Section 5.3, Air for Combustion and Ventilation for

required size of ventilation grills or ducts.

IMPORTANT:

Do not provide openings for inlet

or outlet air into attic if attic has a thermostatcontrolled power vent. Heated air entering the attic will activate the power vent.

VENTILATION AIR

Ventilation Air From Inside Building

This fresh air would come from an adjoining un conﬁned space. When ventilating to an adjoining unconﬁned space, you must provide two perma nent openings: one within 12” of the ceiling and one within 12” of the ﬂoor on the wall connecting the two spaces (see options 1 and 2, Figure 2). You can also remove door into adjoining room (see option 3, Figure 2). Follow the National Fuel Gas

Code ANSI Z223.1/NFPA 54, Section 5.3, Air for Combustion and Ventilation for required size of

ventilation grills or ducts.

11389

6-01A 7

Figure 3 - Ventilation Air from Outdoors

Shown with Optional Mantel

www.desatech.com

INSTALLATION

NOTICE: This heater is intended for use as supplemental heat. Use this heater along with your primary heating system. Do not install this heater as your pri mary heat source. If you have a central heating system, you may run system’s circulating blower while using heater. This will help circulate the heat throughout the house. In the event of a power outage, you can use this heater as your primary heat source.

WARNING: A qualiﬁed service person must install ﬁre place. Follow all local codes.

Note: Your Comfort Glow ﬁreplace is designed to be used in zero clearance installations. Wall or framing material can be placed directly against any exterior surface of your fireplace, except where standoff spacers are integrally attached. If standoff spacers are attached to your ﬁreplace, these spacers can be placed directly against wall or framing materials.

Use the dimensions shown for rough openings to create the easiest installation (see Built-In Fire place Installation, page 9).

CHECK GAS TYPE

Use the correct gas type (natural or propane/LP) for your unit. If your gas supply is not correct, do not install ﬁreplace. Call dealer where you bought ﬁreplace for proper type ﬁreplace.

WARNING: This appliance is equipped for (natural or pro pane/LP) gas. Field conversion is not permitted.

LOCATING FIREPLACE

WARNING: Maintain the minimum clearances shown in Figure 4 and 5, page 9. If you can, provide greater clearances from ﬂoor, ceiling, and joining wall.

You can recess ﬁrebox into the wall. You can also position ﬁreplace in the optional cabinet mantels. IMPORTANT: Only use optional cabinet mantels speciﬁed in this manual. Purchase the optional mantel from your dealer (see Accessories, page 32).

WARNING: Never install the

ﬁreplace

• in a bedroom or a bathroom

• in a recreational vehicle

• where curtains, furniture, clothing, or other ﬂammable objects are less than 42 inches from the front, top, or sides of the ﬁreplace

• as a ﬁreplace insert

• in high trafﬁc areas

• in windy or drafty areas

CAUTION: This ﬁreplace creates warm air currents. These currents move heat to wall surfaces next to ﬁreplace. Installing ﬁreplace next to vinyl or cloth wall coverings or operating ﬁreplace where impurities (such as, but not limited to, tobacco smoke, aromatic candles, clean-

ing ﬂuids, oil or kerosene lamps, etc.) in the air exist, may discolor walls or cause odors.

IMPORTANT: Vent-free ﬁreplaces add moisture to the air. Although this is beneﬁcial, installing ﬁre place in rooms without enough ventilation air may cause mildew to form from too much moisture. See

Air for Combustion and Ventilation

, page 5.

CAUTION: If you install the ﬁreplace in a home garage

•

ﬁreplace pilot and burner must be at least 18 inches above ﬂoor.

• locate ﬁreplace where moving

vehicle will not hit it.

For convenience and efﬁciency, install ﬁreplace

• where there is easy access for operation, inspec tion, and service.

• in coldest part of room.

www.desatech.com

11389

6-01A

INSTALLATION

3/4" Off The Floor Minimum

6" Minimum From Sides Of Fireplace

Left Side

CEILING

42" Minimum

FLOOR

Right Side

Top Of Mantel Can Be Flush With Wall

Left Side

CEILING

Right Side

42"

Minimum

Continued

An optional blower kit is available from your dealer. See Accessories, page 32. If planning to use blower, locate ﬁreplace near an electrical outlet.

Note: When installing ﬁreplace directly on carpet ing, tile or other combustible material, other than wood ﬂooring, the ﬁreplace shall be installed on a metal or wood panel extending the full width and depth of the ﬁreplace.

0" Minimum Clearance To Top Surface Of Carpeting, Tile Or Other Combustible Material

Figure 4 - Mounting Clearances As

Viewed From Front of Fireplace Shown

Built In The Wall

BUILT-IN FIREPLACE INSTALLATION

Built-in installation of this ﬁreplace involves installing ﬁreplace into a framed-in enclosure. This makes the front of ﬁreplace ﬂush with wall. Follow the instructions below to install the ﬁreplace in this

manner. If installing a built-in mantel above the

ﬁreplace, you must follow the clearances shown in Figure 9, page 11. If using for built-in installation off of the ﬂoor, follow clearances shown in Figure 4.

Actual Framing Height 26" 26 Front Width 26 Depth 9 1/2" 10 1/2" Bottom 3/4" 3/4"

1. Frame in rough opening. Use dimensions shown

in Figure 6 for the rough opening.

If installing in a corner, use dimensions shown

in Figure 7 for the rough opening. The height

/8" which is the same as the wall opening

is 26 above.

2. An optional blower accessory is available (see

Accessories, page 32). There are two options for connecting blower to electrical source.

Option one: Have a licensed electrician install

a properly grounded, three-prong 120-volt electrical outlet at ﬁreplace location. Locate outlet inside the framed enclosure. Blower power cord will plug into this outlet.

/4" 26 7/8"

/8"

0" Minimum Clearance To Top Surface Of Carpeting, Tile Or Other Combustible Material

Figure 5 - Mounting Clearances As

Viewed From Front of Fireplace Shown

11389

with Optional Mantel

6-01A 9

Figure 6 - Rough Opening for Installing

in Wall

Figure 7 - Rough Opening for Installing

in Corner

www.desatech.com

INSTALLATION

Continued

Option two: Have a licensed electrician con-

nect blower to electrical source at junction box inside ﬁreplace.

If using option one, have electrical outlet in

stalled at this time. If using option two, do not connect blower to electrical source at junction box until step 6.

3. Install gas piping to ﬁreplace location. This installation includes an approved ﬂexible gas line (if allowed by local codes) after the equip ment shutoff valve. The ﬂexible gas line must be the last item installed on the gas piping.

4. Carefully set ﬁreplace in front of rough opening with back of ﬁreplace inside wall opening.

5. Attach ﬂexible gas line to ﬁreplace gas regula tor. See Connecting Fireplace to Gas Supply, page 16.

6. If the optional blower has been installed con nect blower to electrical source.

Option one: Route blower electrical cord

through side or rear access door of ﬁreplace. Plug electrical cord into electrical outlet.

Option two: Have a licensed electrician con-

nect blower to electrical source at junction box inside ﬁreplace.

7. Bend four nailing ﬂanges on outer casing with pliers (see Figure 8).

8. Attach fireplace to wall studs using nails or wood screws through holes in nailing ﬂange.

9. Check all gas connections for leaks. See Checking Gas Connections, page 17.

IMPORTANT: When finishing your firebox, combustible materials such as wall board, gyp sum board, sheet rock, drywall, plywood, etc. may be butted up next to the sides and top of the ﬁrebox. Combustible materials should never overlap the ﬁrebox front facing. Firebox should not be placed on top of carpet or other kinds of ﬁbrous material.

WARNING: Do not allow any combustible materials to overlap the ﬁrebox front facing.

IMPORTANT: Noncombustible materials such as brick, tile, etc. may overlap the front facing, but should never cover any necessary openings like louvered slots.

WARNING: Do not allow noncombustible materials to cover any necessary openings like louvered slots.

WARNING: Never modify or cover the louvered slots on the front of the ﬁrebox.

WARNING: Use only noncombustible mortar or adhe sives when overlapping the front facing with noncombustible facing material.

Nails or

Wood Screws

Figure 8 - Attaching Fireplace to Wall

Mantel Clearances for Built-In Installation

NOTICE: Surface temperatures

Studs

of adjacent walls and mantels become hot during operation. Walls and mantels above the firebox may become hot to the touch. If installed properly, these temperatures meet the requirement of the national product standard. Follow all minimum clearances shown in this manual.

If placing mantel above built-in ﬁreplace, you must meet minimum clearance between mantel shelf and top of ﬁreplace opening.

Nailing Flanges

www.desatech.com

11389

6-01A

INSTALLATION

13"

16"

19"

21"

2 1/2"

10"

Minimum NonCombustible Material

Continued

NOTICE: If your installation does not meet the minimum clearances shown, you must do one of the following:

• raise the mantel to an acceptable height

• remove the mantel

Note: All vertical measurements are from top of ﬁreplace opening to bottom of mantel shelf.

Mantel Shelf

6. While ﬁrmly holding edges of trim together, tighten both set screws on the adjusting plate with slotted screwdriver.

7. Repeat steps 1 through 6 for other corner.

8. Set trim assembly aside for later installation.

Slot

Shim

Top Trim

Mitered Edge

Side Trim

Set Screws

Adjusting Plate

Figure 10 - Assembling Trim

OPTIONAL MANTEL INSTALLATION

Note: Refer to instructions provided with the mantel for assembly instructions. Refer to instructions below for system installation. If using blower accessory (see Accessories, page 32), see installation instructions on pages 12 through 15.

1. Choose location for ﬁreplace and install gas supply line.

2. Remove screen from ﬁreplace by removing screws in each end of screen rod (see Figure

11). Hold screen rod cover while removing ﬁve hex head screws underneath hood (see Figure 12). Carefully lift and pull out hood (see Figure 13, page 12).

REMOVING BRICK LINER RETAINER

1. Using Phillips screw driver, remove 2 screws

2. Remove brick liner retainers and discard.

ASSEMBLING TRIM

(Trim shipped with mantel)

1. Remove packaging from three pieces of trim.

2. Locate two adjusting plates with set screws,

3. Align shim under adjusting plate as shown in

4. Slide one end of adjusting plate/shim in slot

5. Slide other end of adjusting plate/shim in slot

11389

Figure 9 - Minimum Mantel Clearances

for Built-In Installation

attaching brick liner retainers to vertical sides.

Replace 2 screws into vertical sides.

and two shims in the hardware packet.

Figure 10.

on mitered edge of top trim (see Figure 10).

on mitered edge of side trim (see Figure 10).

6-01A 11

www.desatech.com

Figure 11 - Removing Screen

Hood

Screen Rod Cover

Screw

Figure 12 - Removing Hood Screws

+ 25 hidden pages