Desa CF26NRA, CF26PRA User Manual

UNVENTED (VENT-FREE) BAY FRONT GAS LOG FIREPLACE

A
U
T
O

O
F
F

O
N

OWNER’S OPERATION AND INSTALLATION MANUAL

Patent Pending

Fireplace Shown With Optional Bay Front Mantel

MODELS CF26PRA AND CF26NRA

19,000 TO 26,000 BTU/HR REMOTE CONTROL READY

WARNING: If the information in this manual is not fol­lowed exactly, a fire or explosion may result causing
property damage, personal injury, or loss of life.

— Do not store or use gasoline or other flammable

vapors and liquids in the vicinity of this or any other
appliance.

— WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any
phone in your building.

• Immediately call your gas supplier from a neighbor’s
phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the fire
department.

— Installation and service must be performed by a quali-

fied installer, service agency, or the gas supplier.

Save this manual for future reference.

For more information, visit www.desatech.com

WARNING: Improper installation, adjustment, altera­tion, service, or maintenance can cause injury or prop­erty damage. Refer to this manual for correct installation
and operational procedures. For assistance or addi­tional information consult a qualified installer, service
agency, or the gas supplier.

WARNING: This is an unvented gas-fired heater. It uses
air (oxygen) from the room in which it is installed. Provi­sions for adequate combustion and ventilation air must
be provided. Refer to Air for Combustion and Ventilation
section on page 5 of this manual.

This appliance may be installed in an aftermarket,* per­manently located, manufactured (mobile) home, where
not prohibited by local codes.

This appliance is only for use with the type of gas indi­cated on the rating plate. This appliance is not convert­ible for use with other gases.

* Aftermarket: Completion of sale, not for purpose of resale, from the manufacturer

TABLE OF CONTENTS

Safety Information ............................................... 3

Local Codes ........................................................ 4

Unpacking ........................................................... 4

Product Identification ...........................................

Product Features ................................................. 5

Remote Control Accessories ............................... 5

Air For Combustion and Ventilation ..................... 5

Installation ........................................................... 8

Operating Fireplace ........................................... 20

Inspecting Burners ........................................... 23

Cleaning and Maintenance ................................ 23

www.desatech.com

Troubleshooting ................................................. 25

Specifications ....................................................

Wiring Diagram .................................................. 29

5

Illustrated Parts Breakdown and Parts List ....... 30

Replacement Parts ............................................ 34

Service Hints ..................................................... 34

Technical Service ..............................................

Parts Central ..................................................... 34

Accessories ....................................................... 35

Warranty Information .........................................

113897

29

34

36

-01A2

SAFETY INFORMATION

WARNING: This product con­tains and/or generates chemicals
known to the state of California
to cause cancer or birth defects,
or other reproductive harm.

IMPORTANT: Read this owner’s
manual carefully and completely
before trying to assemble, op­erate, or service this fireplace.
Improper use of this fireplace
can cause serious injury or death
from burns, fire, explosion,
electrical shock, and carbon
monoxide poisoning.

DANGER: Carbon monoxide
poisoning may lead to death!

Carbon Monoxide Poisoning:

monoxide poisoning resemble the flu, with head
aches, dizziness, or nausea. If you have these signs,
the heater may not be working properly. Get fresh
air at once! Have heater serviced. Some people
are more affected by carbon monoxide than others.
These include pregnant women, people with heart
or lung disease or anemia, those under the influence
of alcohol, and those at high altitudes.

Natural and Propane/LP Gas: Natural and pro-

pane/LP gases are odorless. An odor-making agent
is added to the gas. The odor helps you detect a gas
leak. However, the odor added to the gas can fade.
Gas may be present even though no odor exists.

Make certain you read and understand all warn
ings. Keep this manual for reference. It is your
guide to safe and proper operation of this heater.

Early signs of carbon

WARNING: Do not allow fans
to blow directly into the fireplace.
Avoid any drafts that alter burner
flame patterns. Ceiling fans can
create drafts that alter burner
flame patterns. Altered burner
patterns can cause sooting.

Due to high temperatures, the
appliance should be located out
of traffic and away from furniture
and draperies.

Do not place clothing or other
flammable material on or near the
appliance. Never place any ob­jects in the fireplace or on logs.

Fireplace front and screen be­come very hot when running fire
place. Keep children and adults

-

away from hot surfaces to avoid
burns or clothing ignition. Fire
place will remain hot for a time
after shutdown. Allow surfaces
to cool before touching.

Carefully supervise young chil­dren when they are in the room
with fireplace. When using the
hand-held remote accessory,
keep selector switch in the OFF
position to prevent children

-

from turning on burners with
remote.

-

-

WARNING: Any change to
this heater or its controls can
be dangerous.

You must operate this fireplace
with a fireplace screen in place.
Make sure fireplace screen is
closed before running heater.

WARNING: Do not use a
blower insert, heat exchanger
insert, or other accessory not ap­proved for use with this heater.

-01A 3

113897

www.desatech.com

Keep the appliance area clear
and free from combustible ma
terials, gasoline, and other flam
mable vapors and liquids.

-

-

SAFETY INFORMATION

Continued

1. This appliance is only for use with the type
of gas indicated on the rating plate. This ap
pliance is not convertible for use with other
gases.

2. Do not place propane/LP supply tank(s) in
side any structure. Locate propane/LP supply
tank(s) outdoors (propane/LP units only).

3. If you smell gas

• shut off gas supply

• do not try to light any appliance

• do not touch any electrical switch; do not use

any phone in your building

• immediately call your gas supplier from a

neighborʼs phone. Follow the gas supplierʼs
instructions

• if you cannot reach your gas supplier, call

the fire department

4. This fireplace shall not be installed in a bed
room or bathroom.

5. Do not use this fireplace as a wood-burning
fireplace. Use only the logs provided with the
fireplace.

6. Do not add extra logs or ornaments such as
pine cones, vermiculite, or rock wool. Using
these added items can cause sooting. Do not
add lava rock around base. Rock and debris
could fall into the control area of fireplace.

7. This fireplace is designed to be smokeless. If
logs ever appear to smoke, turn off fireplace
and call a qualified service person. Note:
During initial operation, slight smoking could
occur due to log curing and fireplace burning
manufacturing residues.

8. To prevent the creation of soot, follow the
instructions in Cleaning and Maintenance
page 23.

9. Before using furniture polish, wax, carpet
cleaner, or similar products, turn heater off.
If heated, the vapors from these products may
create a white powder residue within burner
box or on adjacent walls or furniture.

10. This fireplace needs fresh air ventilation to run
properly. This fireplace has an Oxygen Deple
tion Sensing (ODS) safety shutoff system. The
ODS shuts down the fireplace if not enough
fresh air is available. See Air for Combustion
and Ventilation, page 5. If fireplace keeps
shutting off, see Troubleshooting, page 25.

11. Do not run fireplace

• where flammable liquids or vapors are used
or stored.

• under dusty conditions.

-

12. Do not use this fireplace to cook food or to
burn paper or other solid fuels.

13. Do not use fireplace if any part has been under

­water. Immediately call a qualified service

technician to inspect the room fireplace and
to replace any part of the control system and
any gas control which has been under water.

14. Turn off and unplug fireplace and let cool
before servicing. Only a qualified service
person should service and repair fireplace.

15. Operating fireplace above elevations of 4,500
feet could cause pilot outage.

16. Do not operate fireplace if any log is broken.
Do not operate fireplace if a log is chipped
(dime-sized or larger).

17. To prevent performance problems, do not use

­propane/LP fuel tank of less than 100 lbs.

capacity (propane/LP units only).

18. Prov id e adequate clearances aro un d air
openings.

LOCAL CODES

Install and use fireplace with care. Follow all local
codes. In the absence of local codes, use the lat
est edition of The National Fuel Gas Code, ANSI

Z223.1/NFPA 54

*Available from:

American National Standards Institute, Inc.

National Fire Protection Association, Inc.

,

*.

1430 Broadway

New York, NY 10018

Batterymarch Park

Quincy, MA 02269

UNPACKING

1. Remove and fireplace from carton.

2. Remove all protective packaging applied to
fireplace for shipment.

3. Make sure your fireplace includes one hard
ware packet.

4. Check fireplace for any shipping damage. If

­fireplace is damaged, promptly inform dealer

where you bought fireplace.

-

-

www.desatech.com

113897

-01A4

PRODUCT

IDENTIFICATION

Fireplace
Cabinet

Brick
Liner

Logs

Heater Controls
(Inside Door)

Figure 1 - Vent-Free Propane/LP Gas

Screen

Compact Fireplace

PRODUCT FEATURES

SAFETY PILOT

This fireplace has a pilot with an Oxygen Deple­tion Sensing (ODS) safety shutoff system. The
ODS/pilot is a required feature for vent-free room
fireplaces. The ODS/pilot shuts off the fireplace if
there is not enough fresh air.

PIEZO IGNITION SYSTEM

This fireplace has a piezo ignitor. This system
requires no matches, batteries, or other sources
to light fireplace.

REMOTE CONTROL

ACCESSORIES

There are two optional remote controls that can be
purchased separately for this log heater:

• hand-held ON/OFF remote

• hand-held thermostat remote

See Accessories, page 35.

AIR FOR COMBUSTION

AND VENTILATION

WARNING: This heater shall
not be installed in a confined
space or unusually tight con
struction unless provisions are
provided for adequate combus
tion and ventilation air. Read the
following instructions to insure
proper fresh air for this and
other fuel-burning appliances
in your home.

Todayʼs homes are built more energy efficient than
ever. New materials, increased insulation, and
new construction methods help reduce heat loss
in homes. Home owners weather strip and caulk
around windows and doors to keep the cold air out
and the warm air in. During heating months, home
owners want their homes as airtight as possible.

While it is good to make your home energy effi
cient, your home needs to breathe. Fresh air must
enter your home. All fuel-burning appliances need
fresh air for proper combustion and ventilation.

Exhaust fans, fireplaces, clothes dryers, and fuel
burning appliances draw air from the house to
operate. You must provide adequate fresh air for
these appliances. This will insure proper venting
of vented fuel-burning appliances.

PROVIDING ADEQUATE
VENTILATION

The following are excerpts from National Fuel
Gas Code, ANSI Z223.1/NFPA 54 Section 5.3, Air
for Combustion and Ventilation.

All spaces in homes fall into one of the three fol
lowing ventilation classifications:

1. Unusually Tight Construction

2. Unconfined Space

3. Confined Space

The information on pages 5 through 7 will help
you classify your space and provide adequate
ventilation.

-

-

-

-

-01A 5

113897

www.desatech.com

AIR FOR COMBUSTION

AND VENTILATION

Continued

Unusually Tight Construction

The air that leaks around doors and windows
may provide enough fresh air for combustion and
ventilation. However, in buildings of unusually
tight construction, you must provide additional
fresh air.

Unusually tight construction is defined as
construction where:

a. walls and ceilings exposed to the out

side atmosphere have a continuous
water vapor retarder with a rating of
one perm (6 x 10
less with openings gasketed or sealed
and

b. weather stripping has been added on

openable windows and doors and

c. caulking or sealants are applied to

areas such as joints around window
and door frames, between sole plates
and floors, between wall-ceiling joints,
between wall panels, at penetrations
for plumbing, electrical, and gas lines,
and at other openings.

If your home meets all of the three criteria
above, you must provide additional fresh
air. See Ventilation Air From Outdoors,
page 7.

If your home does not meet all of the three
criteria above, proceed to Determining

Fresh-Air Flow For Fireplace Location

below.

Confined and Unconfined Space

The National Fuel Gas Code, ANSI Z223.1 defines
a confined space as a space whose volume is less
than 50 cubic feet per 1,000 Btu per hour (4.8 m
per kw) of the aggregate input rating of all appli­ances installed in that space and an unconfining
space as a space whose volume is not less than
50 cubic feet per 1,000 Btu per hour (4.8 m3 per
kw) of the aggregate input rating of all appliances
installed in that space. Rooms communicating
directly with the space in which the appliances
are installed*, through openings not furnished
with doors, are considered a part of the uncon­fined space.

* Adjoining rooms are communicating only if
there are doorless

-11

kg per pa-sec-m2) or

DETERMINING FRESH-AIR FLOW
FOR FIREPLACE LOCATION

Determining if You Have a Confined or
Unconfined Space

Use this work sheet to determine if you have a
confined or unconfined space.

Space: Includes the room in which you will
install heater plus any adjoining rooms with door
less passageways or ventilation grills between
the rooms.

1. Determine the volume of the space (length x
width x height).

-

Length x Width x Height =__________cu. ft.

(volume of space)

Example: Space size 20 ft. (length) x 16 ft.

(width) x 8 ft. (ceiling height) = 2560 cu. ft.
(volume of space)

If additional ventilation to adjoining room is

supplied with grills or openings, add the volume
of these rooms to the total volume of the space.

2. Multiply the space volume by 20 to determine
the maximum Btu/Hr the space can support.

__________ (volume of space) x 20 = (Maxi-

mum Btu/Hr the space can support)

Example: 2560 cu. ft. (volume of space) x 20 =

51,200 (maximum Btu/Hr the space can support)

3. Add the Btu/Hr of all fuel burning appliances in
the space.

Vent-free fireplace ___________

Gas water heater* ___________

Gas furnace ___________

Vented gas heater ___________

Gas fireplace logs ___________

,

Other gas appliances* + ___________

Total = ___________

* Do not include direct-vent gas appliances. Di

rect-vent draws combustion air from the outdoors
and vents to the outdoors.

3

Example:

Gas water heater

Vent-free fireplace + ________

Total = ________

4. Compare the maximum Btu/Hr the space can
support with the actual amount of Btu/Hr used.

_________

_________
Example: 51,200 Btu/Hr (maximum the space

56,000 Btu/Hr (actual amount of

Btu/Hr (maximum the space can support)

Btu/Hr (actual amount of Btu/Hr used)

can support)

Btu/Hr used)

30,000

__________ Btu/Hr

26,000

56,000

-

Btu/Hr

Btu/Hr

Btu/Hr

Btu/Hr

Btu/Hr

Btu/Hr

Btu/Hr

-

Btu/Hr

Btu/Hr

www.desatech.com

113897

-01A6

AIR FOR COMBUSTION

Or
Remove
Door into

Adjoining

Room,

Option

3

Ventilation Grills

Into Adjoining Room,

Option 2

12"

12"

Ventilation

Grills

into Adjoining

Room,

Option 1

Outlet
Air

Ventilated
Attic

Outlet

A

ir

Inlet
Air

Inlet Air

Ventilated

Crawl Space

To Attic

To
Crawl
Space

AND VENTILATION

Continued

The space in the above example is a confined space
because the actual Btu/Hr used is more than the maxi­mum Btu/Hr the space can support. You must provide
additional fresh air. Your options are as follows:

A. Rework worksheet, adding the space of an adjoin-

ing room. If the extra space provides an unconfined
space, remove door to adjoining room or add
ventilation grills between rooms. See Ventilation

Air From Inside Building.

B. Vent room directly to the outdoors. See Ventila

tion Air From Outdoors.

C. Install a lower Btu/Hr fireplace, if lower Btu/Hr

size makes room unconfined.

If the actual Btu/Hr used is less than the maximum
Btu/Hr the space can support,
confined space. You will need no additional fresh
air ventilation.

WARNING: If the area in
which the heater may be oper­ated is smaller than that defined
as an unconfined space or if the
building is of unusually tight
construction, provide adequate
combustion and ventilation air
by one of the methods described
in the National Fuel Gas Code,
ANSI Z223.1/NFPA 54 Section 5.3
or applicable local codes.

the space is an un-

-

Figure 2 - Ventilation Air from Inside

Building Shown with Optional Mantel

Ventilation Air From Outdoors

Provide extra fresh air by using ventilation grills or
ducts. You must provide two permanent openings:
one within 12” of the ceiling and one within 12”
of the floor. Connect these items directly to the
outdoors or spaces open to the outdoors. These
spaces include attics and crawl spaces. Follow the

National Fuel Gas Code ANSI Z223.1/NFPA 54,
Section 5.3, Air for Combustion and Ventilation for

required size of ventilation grills or ducts.

IMPORTANT:

Do not provide openings for inlet

or outlet air into attic if attic has a thermostat­controlled power vent. Heated air entering the attic
will activate the power vent.

VENTILATION AIR

Ventilation Air From Inside Building

This fresh air would come from an adjoining un
confined space. When ventilating to an adjoining
unconfined space, you must provide two perma
nent openings: one within 12” of the ceiling and
one within 12” of the floor on the wall connecting
the two spaces (see options 1 and 2, Figure 2). You
can also remove door into adjoining room (see
option 3, Figure 2). Follow the National Fuel Gas

Code ANSI Z223.1/NFPA 54, Section 5.3, Air for
Combustion and Ventilation for required size of

ventilation grills or ducts.

113897

-01A 7

-

-

Figure 3 - Ventilation Air from Outdoors

Shown with Optional Mantel

www.desatech.com

INSTALLATION

NOTICE: This heater is intended
for use as supplemental heat.
Use this heater along with your
primary heating system. Do not
install this heater as your pri
mary heat source. If you have a
central heating system, you may
run system’s circulating blower
while using heater. This will help
circulate the heat throughout the
house. In the event of a power
outage, you can use this heater
as your primary heat source.

WARNING: A qualified ser­vice person must install fire
place. Follow all local codes.

Note: Your Comfort Glow fireplace is designed
to be used in zero clearance installations. Wall or
framing material can be placed directly against
any exterior surface of your fireplace, except
where standoff spacers are integrally attached.
If standoff spacers are attached to your fireplace,
these spacers can be placed directly against wall
or framing materials.

Use the dimensions shown for rough openings to
create the easiest installation (see Built-In Fire
place Installation, page 9).

CHECK GAS TYPE

Use the correct gas type (natural or propane/LP)
for your unit. If your gas supply is not correct, do
not install fireplace. Call dealer where you bought
fireplace for proper type fireplace.

WARNING: This appliance
is equipped for (natural or pro
pane/LP) gas. Field conversion
is not permitted.

LOCATING FIREPLACE

WARNING: Maintain the mini­mum clearances shown in Figure
4, page 9. If you can, provide
greater clearances from floor,
ceiling, and joining wall.

-

-

-

You can recess firebox into the wall. You can also
position fireplace in the optional cabinet mantels.
IMPORTANT: Only use optional cabinet mantels
specified in this manual. Purchase the optional man­tel from your dealer (see Accessories, page 35).

WARNING: Never install the

fireplace

• in a bedroom or a bathroom

• in a recreational vehicle

• where curtains, furniture,
clothing, or other flammable
objects are less than 42 inches
from the front, top, or sides of
the fireplace

• as a fireplace insert

• in high traffic areas

• in windy or drafty areas

CAUTION: This fireplace cre­ates warm air currents. These
currents move heat to wall sur­faces next to fireplace. Installing
fireplace next to vinyl or cloth
wall coverings or operating
fireplace where impurities (such
as, but not limited to, tobacco
smoke, aromatic candles, clean-

-

ing fluids, oil or kerosene lamps,
etc.) in the air exist, may discolor
walls or cause odors.

IMPORTANT: Vent-free fireplaces add moisture
to the air. Although this is beneficial, installing fire
place in rooms without enough ventilation air may
cause mildew to form from too much moisture. See

Air for Combustion and Ventilation

, page 5.

CAUTION: If you install the
fireplace in a home garage

•

fireplace pilot and burner must be
at least 18 inches above floor.

• locate fireplace where moving

vehicle will not hit it.

For convenience and efficiency, install fireplace

• where there is easy access for operation, inspec
tion, and service.

• in coldest part of room.

-

-

www.desatech.com

113897

-01A8

INSTALLATION

36

5

/8

"

25

7

/8

"

51

3

/

4

"

26

7

/8

"

26

7

/

8

"

26

7

/

8

"

3/4" Off
The Floor
Minimum

10

1

/

2

"

Continued

An optional blower kit is available from your
dealer. See Accessories, page 35. If planning to use
blower, locate fireplace near an electrical outlet.

Minimum Clearances For Side Combustible
Material, Side Wall, and Ceiling

A. Clearances from the side of the fireplace

cabinet to any combustible material and wall
should follow diagram in Figure 4.

Example: The face of a mantel, bookshelf,

etc. is made of combustible material and
protrudes 3
tible material must be 4" from the side of the
fireplace opening (see Figure 4).

B. Clearances from the top of the fireplace open

ing to the ceiling should not be less than 42
inches.

*Minimum 16 inches from Side Wall

Figure 4 - Minimum Clearance for

1

/2" from the wall. This combus-

Example

Combustible to Wall

*

1. Frame in rough opening. Use dimensions shown

in Figure 5 for the rough opening.

If installing in a corner, use dimensions shown

in Figure 6 for the rough opening. The height

1

/8" which is the same as the wall opening

is 26
above.

2. An optional blower accessory is available (see

Accessories, page 35). There are two options
for connecting blower to electrical source.

Option one: Have a licensed electrician install

a properly grounded, three-prong 120-volt
electrical outlet at fireplace location. Locate
outlet inside the framed enclosure. Blower
power cord will plug into this outlet.

Option two: Have a licensed electrician con-

nect blower to electrical source at junction box

-

inside fireplace.

If using option one, have electrical outlet in

stalled at this time. If using option two, do not
connect blower to electrical source at junction
box until step 6.

3. Install gas piping to fireplace location. This

installation includes an approved flexible gas
line (if allowed by local codes) after the equip
ment shutoff valve. The flexible gas line must
be the last item installed on the gas piping.

4. Carefully set fireplace in front of rough opening

with back of fireplace inside wall opening.

5. Attach flexible gas line to fireplace gas regula

tor. See Connecting Fireplace to Gas Supply
page 16.

-

-

­,

BUILT-IN FIREPLACE
INSTALLATION

Built-in installation of this fireplace involves in­stalling fireplace into a framed-in enclosure. This
makes the front of fireplace flush with wall. Follow
the instructions below to install the fireplace in this
manner. If installing a built-in mantel above the
fireplace, you must follow the clearances shown
in Figure 8, page 11.

Note: If desired, purchase a four-sided trim kit for
built-in installations. See Accessories, page 35.

Actual Framing
Height 26" 26
Front Width 26
Depth 9 1/2" 10 1/2"
Bottom 3/4" 3/4"

-01A 9

113897

3

/4" 26 7/8"

Figure 5 - Rough Opening for Installing

7

/8"

Figure 6 - Rough Opening for Installing

www.desatech.com

in Wall

in Corner

INSTALLATION

Continued

6. If the optional blower has been installed con­nect blower to electrical source.

Option one: Route blower electrical cord

through side or rear access door of fireplace.
Plug electrical cord into electrical outlet.

Option two: Have a licensed electrician con-

nect blower to electrical source at junction box
inside fireplace.

7. Bend four nailing flanges on outer casing with
pliers (see Figure 7).

8. Attach fireplace to wall studs using nails
or wood screws through holes in nailing
flange.

9. Check all gas connections for leaks. See
Checking Gas Connections, page 17.

IMPORTANT: When finishing your firebox,
combustible materials such as wall board, gyp
sum board, sheet rock, drywall, plywood, etc.
may be butted up next to the sides and top of
the firebox. Combustible materials should never
overlap the firebox front facing. Firebox should
not be placed on top of carpet or other kinds of
fibrous material.

WARNING: Do not allow any
combustible materials to overlap
the firebox front facing.

IMPORTANT: Noncombustible materials such as
brick, tile, etc. may overlap the front facing, but
should never cover any necessary openings like
louvered slots.

WARNING: Do not allow non­combustible materials to cover
any necessary openings like
louvered slots.

WARNING: Never modify or
cover the louvered slots on the
front of the firebox.

Nails or
Wood
Screws

Figure 7 - Attaching Fireplace to Wall

Mantel Clearances for Built-In Installation

-

NOTICE: Surface temperatures

Studs

of adjacent walls and mantels
become hot during operation.
Walls and mantels above the
firebox may become hot to
the touch. If installed properly,
these temperatures meet the
requirement of the national
product standard. Follow all
minimum clearances shown in
this manual.

If placing mantel above built-in fireplace, you must
meet minimum clearance between mantel shelf and
top of fireplace opening.

NOTICE: If your installation does
not meet the minimum clear­ances shown, you must do one
of the following:

• raise the mantel to an accept­able height

• remove the mantel

Nailing
Flanges

WARNING: Use only non­combustible mortar or adhe­sives when overlapping the front
facing with noncombustible
facing material.

www.desatech.com

113897

-01A10

13"

16"

19"

21"

2 1/2"

6"

8"

10"

Minimum Non­Combustible
Material

Note: All vertical
measurements
are from top
of fireplace
opening to
bottom of
mantel shelf.

REMOVING BRICK LINER
RETAINER

1. Using Phillips screw driver, remove 2 screws

2. Remove brick liner retainers and discard.

ASSEMBLING TRIM

(Trim shipped with mantel)

1. Remove packagi ng from three pieces of

2. Locate two adjusting plates with set screws,

3. Align shim under adjusting plate as shown in

4. Slide one end of adjusting plate/shim in slot

5. Slide other end of adjusting plate/shim in slot

6. While firmly holding edges of trim together,

7. Repeat steps 1 through 6 for other corner.

8. Set trim assembly aside for later installation.

INSTALLATION

Continued

Mantel Shelf

Figure 8 - Minimum Mantel Clearances

for Built-In Installation

attaching brick liner retainers to vertical
sides.

Replace 2 screws into vertical sides.

trim.

and two shims in the hardware packet.

Figure 9.

on mitered edge of top trim (see Figure 9).

on mitered edge of side trim (see Figure 9).

tighten both set screws on the adjusting plate
with slotted screwdriver.

Set Screws

Top
Trim

Slot

Shim

Mitered
Edge

Side

Adjusting

Trim

Plate

Slot

Figure 9 - Assembling Trim

OPTIONAL MANTEL INSTALLATION

Note: Refer to instructions provided with the man-
tel for assembly instructions. Refer to instructions
below for system installation. If using blower ac
cessory (see Accessories, page 35), see installation
instructions on pages 12 through 15.

1. Choose location for fireplace and install gas
supply line.

2. Remove screen from fireplace by removing
screws in each end of screen rod (see Figure

10). Hold screen rod cover while removing
five hex head screws underneath hood (see
Figure 11). Carefully lift and pull out hood
(see Figure 12, page 12).

Figure 10 - Removing Screen

Hood

Screen Rod
Cover

Screw

Figure 11 - Removing Hood Screws

-

-01A 11

113897

www.desatech.com