Page 1
DEROYAL® LATCHING SAFETY AUTO
RESET MONITOR
NON-STERILE
NOT MADE WITH NATURAL RUBBER LATEX
RX ONLY FEDERAL U.S.A. LAW RESTRICTS THIS DEVICE
TO SALE OR USE BY OR ON THE ORDER
OF A PHYSICIAN OR PROPERLY LICENSED
PRACTITIONER.
IMPORTANT INFORMATION
Please read all instructions, warnings and
precautions before use. Correct set up is
essential for proper functioning of product.
This product is to be used by a licensed caregiver
only for the use it was intended.
INTENDED USE
The DeRoyal® Latching Safety Auto-Reset Monitor is
intended to alert staff and patients in the event the
patient attempts to exit the bed, wheelchair and/or
recliner. It is also intended to be used with latching
nurse call systems.
WARNINGS
Failure to comply with these warnings may result
in injury or death. This device is not suitable for all
individuals. This device is not a substitute for visual
monitoring by caregiver. The manufacturer does
not claim that this device will stop elopement and/
or stop falls. This device is designed to augment
caregivers’ comprehensive patient mobility
management program. Test this device before each
use. Do not use without reading the instructions.
This monitor is to be installed by a licensed
caregiver. As such, it is the entire responsibility of the
caregiver to ensure that the system is not designed
to replace good caregiving practices including but
not limited to:
• Direct patient supervision
• Adequate training for staff personnel for fall
prevention and/or elopement
• Testing of the system before each use
DO NOT connect a DeRoyal® alarm to other
manufacturers’ sensors. Use of another
manufacturers’ sensor may damage the alarm, may
cause the fall monitoring system not to function as
intended, and will void the DeRoyal warranty.
Be sure to follow your facility’s policies and
guidelines for frequency of patient monitoring.
INSTRUCTIONS FOR USE
SETTING UP THE MONITOR AND SENSOR PAD
1. Open battery compartment door with a small
Phillips-head screwdriver. Insert batteries.
2. Close the battery door and secure it with the
small Phillips-head screwdriver.
3. Place one bed sensor pad or chair sensor pad
within reach.
4. Connect the monitor to the bed sensor pad or the
chair sensor pad. Plug the cord end of the sensor
pad into the bottom of the monitor. Pinch the cord
together and route it through the cord protection
recess on the monitor (near the plug input).
5. Put pressure on the sensor pad to activate the
pad and monitor. The monitor will beep two
times to indicate that the sensor pad and fall
monitor are in use. The “Monitor Status” light will
blink while pressure remains on the pad. When
pressure is removed, the fall monitor will sound
the alarm. Press the “Reset” button to silence the
alarm
6. If the “Pad Lost Light” is on, check to make sure
the cord is plugged in and reset the system.
7. Test the system before use.
MOUNTING THE MONITOR
1. The strap with buckle can be used to attach the
monitor to a desired location.
2. To mount the monitor, mount the screws onto
the wall or headboard. Hang the monitor on the
screws using the mounting holes on back of the
monitor.
TURNING OFF OR RESETTING THE ALARM
1. When the alarm is triggered, the alarm can be
turned off and reset with either the reset button or
Caregiver Key™ function.
2. Select either “Reset Button ON” or “Caregiver
Key™ ON” with the switch on the side of the
monitor. Use the end of a pen to move the switch.
3. If set on “Reset Button ON” position, the caregiver
can reset the monitor by pressing the reset button
located on the front of the monitor.
4. If set on the “Caregiver Key™ ON” position, the
monitor can only be reset by using the Caregiver
Key™ provided with the monitor. The Caregiver
Key™ must be placed over the red dot to reset
the monitor.
Page 2
VOLUME, TONE AND DELAY OPTIONS
1. Adjust the volume by turning the dial located
inside the battery compartment.
2. Select an alarm tone by adjusting the switch
inside the battery compartment to the desired
setting.
3. Select alarm tone delay time by adjusting the
switch inside the battery compartment.
OPTIONAL ITEMS
1. AC Adaptor can be purchased separately.
2. Nurse call cord can be purchased separately
if the patient’s room does not supply one that
accommodates this device.
CARE INSTRUCTIONS
Wipe clean with disinfectant wipes. After cleaning,
test device before each use.
STORAGE AND TRANSPORT CONDITIONS
KEEP DRY
KEEP AWAY FROM SUNLIGHT
WARRANTY
DEROYAL® PRODUCTS ARE WARRANTED FOR
NINETY (90) DAYS FROM THE DATE OF SHIPMENT
FROM DEROYAL AS TO PRODUCT QUALITY
AND WORKMANSHIP. DEROYAL’S WRITTEN
WARRANTIES ARE GIVEN IN LIEU OF ANY
IMPLIED WARRANTIES, INCLUDING WARRANTIES
OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE.
Manufacturerd for:
DeRoyal Industries, Inc.
200 DeBusk Lane
Powell, TN 37849 USA
888.938.7828 or (001) 865.938.7828
www.deroyal.com
Part#0-1950 Revised 4/19
©2019 DeRoyal Industries, Inc.
All Rights Reserved.
DeRoyal, the DeRoyal logo, and Improving Care.
Improving Business. are registered trademarks of
DeRoyal Industries, Inc.
Safety Auto-Reset and Caregiver Key are trademarks
of Smart Caregiver Corporation.
Loading...