Denver WCT-8020W User manual

Infrared Wild Camera

User’s Manual

WCT-8020W

123

INSTALLING BATTERIES

USING AA -ALKALINE BATTERIES

1 Pull the gap lightly and open battery compartment.
2 Reference the battery icons located on the inside of the battery

compartment. Insert the batteries according to the positive and
negative battery icons.

3 Close the battery compartment to resist water and dust.
4 NOTE: Installing any of the 8-AA batteries in the wrong

direction may cause the batteries to leak acid and could possibly
explode, causing camera failure and damage to the battery
compartment.

4

INSTALLING MEMORY

CARD

INSTALL MICRO­SD CARD

1. Insert the Micro SD

card with the
contacts facing
down. The Micro SD
card should slide in
freely with little
resistance. Continue
pressing the card
inward until you hear
a click. This means
the Micro SD card is
locked in place and
ready for use.

2. To remove Micro SD

card, press the card
inwards to release.

5

QUICK START

Enter to TEST mode

Slide the mode switch from OFF to TEST position to activate the
camera and view the user setup screen.

There is a control panel with 8 keys when you open the camera.

6

OPERATING BUTTONS

REPLAY: Press this button to start the replay mode; Press it to play

a video, press it again to stop the playing.

Up: Change to the working mode for video recordings.
Down: Change to the manual recording mode for taking photos.
SHOT/OK: Manually take a video or photo depending on the set

recording mode. Video recordings are ended by pressing the SHOT
button.
MENU: Open the Settings menu using the MENU button.
Generally, it is recommended to place the camera at the height of 3 to
6 feet (1 to 2 meters) to the ground.

Wi-Fi APP Function

Search “Denver WCT-8020W” in APP store (for IOS) or Google
Play (for android) with your smart phone and download it.

1. TEST Mode (Check the Wi-Fi status and change the settings)

1.1. Turn the mode switch to TEST position, press the small button

under the key board for 5 seconds to clear the code and then
start to pair the remote control with the camera.
(Under TEST mode, the remote control only can pair with the
camera.)

1.2. Then press button on the camera to open the WIFI

function (under TEST mode).
You will find the WIFI name (HUNTCAM-) and password
(12345678) is displayed on the screen.

7

1.3. Use your phone to search the Wi-Fi name and enter the

password, then the camera screen will show: Wi-Fi connected.

1.4. WIFI name or password can be changed in the APP when

connected.

2. ON mode

● Turn the mode switch of the camera to ON position, then

the camera will start work after 10 seconds count down,
meanwhile the red indicator light will flash.

● Press the ON button to open the Wi-Fi switch of the remote

control. Once the Wi-Fi is opened, the blue indicator light will
flash until your phone connected it.

● Refer to the section 1.2~1.3 to connect your smart phone to the

camera wifi. After connected, the camera will start to work.

2.1. You can operate the camera to take picture or video via the

APP.

8

2.2. You can find all pictures or videos captured in “File” (see

below picture). And also you can download all files to the
photo album without taking the Micro SD card out.

3. OFF mode

3.1. Press the OFF button of the remote control, the Wi-Fi function

will be closed and then it will work like a normal wild camera.
The camera captures picture or video once it detects motions.
You can download the pictures/videos when you connect the
Wi-Fi again

9

Note: Password: 4 digital numbers (1314 is the universal password)

10

Please notice - All products are subject to change without any
notice. We take reservations for errors and omissions in the
manual.

ALL RIGHTS RESERVED, COPYRIGHT DENVER

ELECTRONICS A/S

Electric and electronic equipment and included batteries
contains materials, components and substances that can be
hazardous to your health and the environment, if the waste
material (discarded electric and electronic equipment and
batteries) is not handled correctly.

Electric and electronic equipment and batteries is marked with
the crossed out trash can symbol, seen above. This symbol
signifies that electric and electronic equipment and batteries
should not be disposed of with other household waste, but
should be disposed of separately.

As the end user it is important that you submit your used
batteries to the appropriate and designated facility. In this
manner you make sure that the batteries are recycled in
accordance with legislature and will not harm the environment.

11

All cities have established collection points, where electric and
electronic equipment and batteries can either be submitted
free of charge at recycling stations and other collection sites,
or be collected from the households. Additional information is
available at the technical department of your city.

Hereby, Inter Sales A/S declares that the radio equipment type
WCT-8020W is in compliance with Directive 2014/53/EU. The
full text of the EU declaration of conformity is available at the
following internet address: www.denver-electronics.com and
then click the search ICON on topline of website. Write model
number: WCT-8020W. Now enter product page, and red
directive is found under downloads/other downloads.

Operating Frequency Range:
Max Output Power:

DENVER ELECTRONICS A/S
Omega 5A, Soeften

DK-8382 Hinnerup
Denmark

www.facebook.com/denverelectronics

12